1 /* 2 * Copyright (C) 2014 Evgeni Dobrev <evgeni@studio-punkt.com> 3 * 4 * Based on sheevaplug.c originally written by 5 * Prafulla Wadaskar <prafulla@marvell.com> 6 * (C) Copyright 2009 7 * Marvell Semiconductor <www.marvell.com> 8 * 9 * SPDX-License-Identifier: GPL-2.0+ 10 */ 11 12 #include <common.h> 13 #include <miiphy.h> 14 #include <asm/arch/soc.h> 15 #include <asm/arch/mpp.h> 16 #include <asm/arch/cpu.h> 17 #include <asm/io.h> 18 19 DECLARE_GLOBAL_DATA_PTR; 20 21 int board_early_init_f(void) 22 { 23 /* 24 * default gpio configuration 25 */ 26 mvebu_config_gpio(NAS220_GE_OE_VAL_LOW, NAS220_GE_OE_VAL_HIGH, 27 NAS220_GE_OE_LOW, NAS220_GE_OE_HIGH); 28 29 /* Multi-Purpose Pins Functionality configuration */ 30 static const u32 kwmpp_config[] = { 31 MPP0_NF_IO2, 32 MPP1_NF_IO3, 33 MPP2_NF_IO4, 34 MPP3_NF_IO5, 35 MPP4_NF_IO6, 36 MPP5_NF_IO7, 37 MPP6_SYSRST_OUTn, 38 MPP7_SPI_SCn, 39 MPP8_TW_SDA, 40 MPP9_TW_SCK, 41 MPP10_UART0_TXD, 42 MPP11_UART0_RXD, 43 MPP12_GPO, 44 MPP13_GPIO, 45 MPP14_GPIO, 46 MPP15_SATA0_ACTn, 47 MPP16_SATA1_ACTn, 48 MPP17_SATA0_PRESENTn, 49 MPP18_NF_IO0, 50 MPP19_NF_IO1, 51 MPP20_GPIO, 52 MPP21_GPIO, 53 MPP22_GPIO, 54 MPP23_GPIO, 55 MPP24_GPIO, 56 MPP25_GPIO, 57 MPP26_GPIO, 58 MPP27_GPIO, 59 MPP28_GPIO, 60 MPP29_GPIO, 61 MPP30_GPIO, 62 MPP31_GPIO, 63 MPP32_GPIO, 64 MPP33_GPIO, 65 MPP34_GPIO, 66 MPP35_GPIO, 67 0 68 }; 69 kirkwood_mpp_conf(kwmpp_config, NULL); 70 return 0; 71 } 72 73 int board_init(void) 74 { 75 /* 76 * arch number of board 77 */ 78 gd->bd->bi_arch_number = MACH_TYPE_RD88F6192_NAS; 79 80 /* adress of boot parameters */ 81 gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; 82 83 return 0; 84 } 85 86 #ifdef CONFIG_RESET_PHY_R 87 /* Configure and enable MV88E1116 PHY */ 88 void reset_phy(void) 89 { 90 u16 reg; 91 u16 devadr; 92 char *name = "egiga0"; 93 94 if (miiphy_set_current_dev(name)) 95 return; 96 97 /* command to read PHY dev address */ 98 if (miiphy_read(name, 0xEE, 0xEE, (u16 *)&devadr)) { 99 printf("Err..%s could not read PHY dev address\n", __func__); 100 return; 101 } 102 103 /* 104 * Enable RGMII delay on Tx and Rx for CPU port 105 * Ref: sec 4.7.2 of chip datasheet 106 */ 107 miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); 108 miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); 109 reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); 110 miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); 111 miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); 112 113 /* reset the phy */ 114 miiphy_reset(name, devadr); 115 116 printf("88E1116 Initialized on %s\n", name); 117 } 118 #endif /* CONFIG_RESET_PHY_R */ 119