1 /*
2  * Copyright (C) 2010  Eric C. Cooper <ecc@cmu.edu>
3  *
4  * Based on sheevaplug.c originally written by
5  * Prafulla Wadaskar <prafulla@marvell.com>
6  * (C) Copyright 2009
7  * Marvell Semiconductor <www.marvell.com>
8  *
9  * SPDX-License-Identifier:	GPL-2.0+
10  */
11 
12 #include <common.h>
13 #include <miiphy.h>
14 #include <asm/arch/soc.h>
15 #include <asm/arch/mpp.h>
16 #include <asm/arch/cpu.h>
17 #include <asm/io.h>
18 #include "dockstar.h"
19 
20 DECLARE_GLOBAL_DATA_PTR;
21 
22 int board_early_init_f(void)
23 {
24 	/*
25 	 * default gpio configuration
26 	 * There are maximum 64 gpios controlled through 2 sets of registers
27 	 * the  below configuration configures mainly initial LED status
28 	 */
29 	mvebu_config_gpio(DOCKSTAR_OE_VAL_LOW,
30 			  DOCKSTAR_OE_VAL_HIGH,
31 			  DOCKSTAR_OE_LOW, DOCKSTAR_OE_HIGH);
32 
33 	/* Multi-Purpose Pins Functionality configuration */
34 	static const u32 kwmpp_config[] = {
35 		MPP0_NF_IO2,
36 		MPP1_NF_IO3,
37 		MPP2_NF_IO4,
38 		MPP3_NF_IO5,
39 		MPP4_NF_IO6,
40 		MPP5_NF_IO7,
41 		MPP6_SYSRST_OUTn,
42 		MPP7_GPO,
43 		MPP8_UART0_RTS,
44 		MPP9_UART0_CTS,
45 		MPP10_UART0_TXD,
46 		MPP11_UART0_RXD,
47 		MPP12_SD_CLK,
48 		MPP13_SD_CMD,
49 		MPP14_SD_D0,
50 		MPP15_SD_D1,
51 		MPP16_SD_D2,
52 		MPP17_SD_D3,
53 		MPP18_NF_IO0,
54 		MPP19_NF_IO1,
55 		MPP20_GPIO,
56 		MPP21_GPIO,
57 		MPP22_GPIO,
58 		MPP23_GPIO,
59 		MPP24_GPIO,
60 		MPP25_GPIO,
61 		MPP26_GPIO,
62 		MPP27_GPIO,
63 		MPP28_GPIO,
64 		MPP29_TSMP9,
65 		MPP30_GPIO,
66 		MPP31_GPIO,
67 		MPP32_GPIO,
68 		MPP33_GPIO,
69 		MPP34_GPIO,
70 		MPP35_GPIO,
71 		MPP36_GPIO,
72 		MPP37_GPIO,
73 		MPP38_GPIO,
74 		MPP39_GPIO,
75 		MPP40_GPIO,
76 		MPP41_GPIO,
77 		MPP42_GPIO,
78 		MPP43_GPIO,
79 		MPP44_GPIO,
80 		MPP45_GPIO,
81 		MPP46_GPIO,
82 		MPP47_GPIO,
83 		MPP48_GPIO,
84 		MPP49_GPIO,
85 		0
86 	};
87 	kirkwood_mpp_conf(kwmpp_config, NULL);
88 	return 0;
89 }
90 
91 int board_init(void)
92 {
93 	/*
94 	 * arch number of board
95 	 */
96 	gd->bd->bi_arch_number = MACH_TYPE_DOCKSTAR;
97 
98 	/* address of boot parameters */
99 	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
100 
101 	return 0;
102 }
103 
104 #ifdef CONFIG_RESET_PHY_R
105 /* Configure and enable MV88E1116 PHY */
106 void reset_phy(void)
107 {
108 	u16 reg;
109 	u16 devadr;
110 	char *name = "egiga0";
111 
112 	if (miiphy_set_current_dev(name))
113 		return;
114 
115 	/* command to read PHY dev address */
116 	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
117 		printf("Err..%s could not read PHY dev address\n",
118 			__FUNCTION__);
119 		return;
120 	}
121 
122 	/*
123 	 * Enable RGMII delay on Tx and Rx for CPU port
124 	 * Ref: sec 4.7.2 of chip datasheet
125 	 */
126 	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
127 	miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
128 	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
129 	miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
130 	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
131 
132 	/* reset the phy */
133 	miiphy_reset(name, devadr);
134 
135 	printf("88E1116 Initialized on %s\n", name);
136 }
137 #endif /* CONFIG_RESET_PHY_R */
138 
139 #define GREEN_LED	(1 << 14)
140 #define ORANGE_LED	(1 << 15)
141 #define BOTH_LEDS	(GREEN_LED | ORANGE_LED)
142 #define NEITHER_LED	0
143 
144 static void set_leds(u32 leds, u32 blinking)
145 {
146 	struct kwgpio_registers *r = (struct kwgpio_registers *)MVEBU_GPIO1_BASE;
147 	u32 oe = readl(&r->oe) | BOTH_LEDS;
148 	writel(oe & ~leds, &r->oe);	/* active low */
149 	u32 bl = readl(&r->blink_en) & ~BOTH_LEDS;
150 	writel(bl | blinking, &r->blink_en);
151 }
152 
153 void show_boot_progress(int val)
154 {
155 	switch (val) {
156 	case BOOTSTAGE_ID_RUN_OS:		/* booting Linux */
157 		set_leds(BOTH_LEDS, NEITHER_LED);
158 		break;
159 	case BOOTSTAGE_ID_NET_ETH_START:	/* Ethernet initialization */
160 		set_leds(GREEN_LED, GREEN_LED);
161 		break;
162 	default:
163 		if (val < 0)	/* error */
164 			set_leds(ORANGE_LED, ORANGE_LED);
165 		break;
166 	}
167 }
168