1 /* 2 * (C) Copyright 2009 3 * Marvell Semiconductor <www.marvell.com> 4 * Written-by: Prafulla Wadaskar <prafulla@marvell.com> 5 * 6 * See file CREDITS for list of people who contributed to this 7 * project. 8 * 9 * This program is free software; you can redistribute it and/or 10 * modify it under the terms of the GNU General Public License as 11 * published by the Free Software Foundation; either version 2 of 12 * the License, or (at your option) any later version. 13 * 14 * This program is distributed in the hope that it will be useful, 15 * but WITHOUT ANY WARRANTY; without even the implied warranty of 16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 17 * GNU General Public License for more details. 18 * 19 * You should have received a copy of the GNU General Public License 20 * along with this program; if not, write to the Free Software 21 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, 22 * MA 02110-1301 USA 23 */ 24 25 #include <common.h> 26 #include <miiphy.h> 27 #include <asm/arch/kirkwood.h> 28 #include <asm/arch/mpp.h> 29 #include "sheevaplug.h" 30 31 DECLARE_GLOBAL_DATA_PTR; 32 33 int board_init(void) 34 { 35 /* 36 * default gpio configuration 37 * There are maximum 64 gpios controlled through 2 sets of registers 38 * the below configuration configures mainly initial LED status 39 */ 40 kw_config_gpio(SHEEVAPLUG_OE_VAL_LOW, 41 SHEEVAPLUG_OE_VAL_HIGH, 42 SHEEVAPLUG_OE_LOW, SHEEVAPLUG_OE_HIGH); 43 44 /* Multi-Purpose Pins Functionality configuration */ 45 u32 kwmpp_config[] = { 46 MPP0_NF_IO2, 47 MPP1_NF_IO3, 48 MPP2_NF_IO4, 49 MPP3_NF_IO5, 50 MPP4_NF_IO6, 51 MPP5_NF_IO7, 52 MPP6_SYSRST_OUTn, 53 MPP7_GPO, 54 MPP8_UART0_RTS, 55 MPP9_UART0_CTS, 56 MPP10_UART0_TXD, 57 MPP11_UART0_RXD, 58 MPP12_SD_CLK, 59 MPP13_SD_CMD, 60 MPP14_SD_D0, 61 MPP15_SD_D1, 62 MPP16_SD_D2, 63 MPP17_SD_D3, 64 MPP18_NF_IO0, 65 MPP19_NF_IO1, 66 MPP20_GPIO, 67 MPP21_GPIO, 68 MPP22_GPIO, 69 MPP23_GPIO, 70 MPP24_GPIO, 71 MPP25_GPIO, 72 MPP26_GPIO, 73 MPP27_GPIO, 74 MPP28_GPIO, 75 MPP29_TSMP9, 76 MPP30_GPIO, 77 MPP31_GPIO, 78 MPP32_GPIO, 79 MPP33_GPIO, 80 MPP34_GPIO, 81 MPP35_GPIO, 82 MPP36_GPIO, 83 MPP37_GPIO, 84 MPP38_GPIO, 85 MPP39_GPIO, 86 MPP40_GPIO, 87 MPP41_GPIO, 88 MPP42_GPIO, 89 MPP43_GPIO, 90 MPP44_GPIO, 91 MPP45_GPIO, 92 MPP46_GPIO, 93 MPP47_GPIO, 94 MPP48_GPIO, 95 MPP49_GPIO, 96 0 97 }; 98 kirkwood_mpp_conf(kwmpp_config); 99 100 /* 101 * arch number of board 102 */ 103 gd->bd->bi_arch_number = MACH_TYPE_SHEEVAPLUG; 104 105 /* adress of boot parameters */ 106 gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; 107 108 return 0; 109 } 110 111 int dram_init(void) 112 { 113 int i; 114 115 for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { 116 gd->bd->bi_dram[i].start = kw_sdram_bar(i); 117 gd->bd->bi_dram[i].size = kw_sdram_bs(i); 118 } 119 return 0; 120 } 121 122 #ifdef CONFIG_RESET_PHY_R 123 /* Configure and enable MV88E1116 PHY */ 124 void reset_phy(void) 125 { 126 u16 reg; 127 u16 devadr; 128 char *name = "egiga0"; 129 130 if (miiphy_set_current_dev(name)) 131 return; 132 133 /* command to read PHY dev address */ 134 if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { 135 printf("Err..%s could not read PHY dev address\n", 136 __FUNCTION__); 137 return; 138 } 139 140 /* 141 * Enable RGMII delay on Tx and Rx for CPU port 142 * Ref: sec 4.7.2 of chip datasheet 143 */ 144 miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); 145 miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); 146 reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); 147 miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); 148 miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); 149 150 /* reset the phy */ 151 miiphy_reset(name, devadr); 152 153 printf("88E1116 Initialized on %s\n", name); 154 } 155 #endif /* CONFIG_RESET_PHY_R */ 156