1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * (C) Copyright 2009 4 * Net Insight <www.netinsight.net> 5 * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net> 6 * 7 * Based on sheevaplug.c: 8 * (C) Copyright 2009 9 * Marvell Semiconductor <www.marvell.com> 10 * Written-by: Prafulla Wadaskar <prafulla@marvell.com> 11 */ 12 13 #include <common.h> 14 #include <miiphy.h> 15 #include <asm/mach-types.h> 16 #include <asm/arch/cpu.h> 17 #include <asm/arch/soc.h> 18 #include <asm/arch/mpp.h> 19 #include "openrd.h" 20 21 DECLARE_GLOBAL_DATA_PTR; 22 23 int board_early_init_f(void) 24 { 25 /* 26 * default gpio configuration 27 * There are maximum 64 gpios controlled through 2 sets of registers 28 * the below configuration configures mainly initial LED status 29 */ 30 mvebu_config_gpio(OPENRD_OE_VAL_LOW, 31 OPENRD_OE_VAL_HIGH, 32 OPENRD_OE_LOW, OPENRD_OE_HIGH); 33 34 /* Multi-Purpose Pins Functionality configuration */ 35 static const u32 kwmpp_config[] = { 36 MPP0_NF_IO2, 37 MPP1_NF_IO3, 38 MPP2_NF_IO4, 39 MPP3_NF_IO5, 40 MPP4_NF_IO6, 41 MPP5_NF_IO7, 42 MPP6_SYSRST_OUTn, 43 MPP7_GPO, 44 MPP8_TW_SDA, 45 MPP9_TW_SCK, 46 MPP10_UART0_TXD, 47 MPP11_UART0_RXD, 48 MPP12_SD_CLK, 49 MPP13_SD_CMD, /* Alt UART1_TXD */ 50 MPP14_SD_D0, /* Alt UART1_RXD */ 51 MPP15_SD_D1, 52 MPP16_SD_D2, 53 MPP17_SD_D3, 54 MPP18_NF_IO0, 55 MPP19_NF_IO1, 56 MPP20_GE1_0, 57 MPP21_GE1_1, 58 MPP22_GE1_2, 59 MPP23_GE1_3, 60 MPP24_GE1_4, 61 MPP25_GE1_5, 62 MPP26_GE1_6, 63 MPP27_GE1_7, 64 MPP28_GPIO, 65 MPP29_TSMP9, 66 MPP30_GE1_10, 67 MPP31_GE1_11, 68 MPP32_GE1_12, 69 MPP33_GE1_13, 70 MPP34_GPIO, /* UART1 / SD sel */ 71 MPP35_TDM_CH0_TX_QL, 72 MPP36_TDM_SPI_CS1, 73 MPP37_TDM_CH2_TX_QL, 74 MPP38_TDM_CH2_RX_QL, 75 MPP39_AUDIO_I2SBCLK, 76 MPP40_AUDIO_I2SDO, 77 MPP41_AUDIO_I2SLRC, 78 MPP42_AUDIO_I2SMCLK, 79 MPP43_AUDIO_I2SDI, 80 MPP44_AUDIO_EXTCLK, 81 MPP45_TDM_PCLK, 82 MPP46_TDM_FS, 83 MPP47_TDM_DRX, 84 MPP48_TDM_DTX, 85 MPP49_TDM_CH0_RX_QL, 86 0 87 }; 88 89 kirkwood_mpp_conf(kwmpp_config, NULL); 90 return 0; 91 } 92 93 int board_init(void) 94 { 95 /* 96 * arch number of board 97 */ 98 #if defined(CONFIG_BOARD_IS_OPENRD_BASE) 99 gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE; 100 #elif defined(CONFIG_BOARD_IS_OPENRD_CLIENT) 101 gd->bd->bi_arch_number = MACH_TYPE_OPENRD_CLIENT; 102 #elif defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE) 103 gd->bd->bi_arch_number = MACH_TYPE_OPENRD_ULTIMATE; 104 #endif 105 106 /* adress of boot parameters */ 107 gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; 108 return 0; 109 } 110 111 #ifdef CONFIG_RESET_PHY_R 112 /* Configure and enable MV88E1116/88E1121 PHY */ 113 void mv_phy_init(char *name) 114 { 115 u16 reg; 116 u16 devadr; 117 118 if (miiphy_set_current_dev(name)) 119 return; 120 121 /* command to read PHY dev address */ 122 if (miiphy_read(name, 0xEE, 0xEE, (u16 *)&devadr)) { 123 printf("Err..%s could not read PHY dev address\n", __func__); 124 return; 125 } 126 127 /* 128 * Enable RGMII delay on Tx and Rx for CPU port 129 * Ref: sec 4.7.2 of chip datasheet 130 */ 131 miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); 132 miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); 133 reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); 134 miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); 135 miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); 136 137 /* reset the phy */ 138 miiphy_reset(name, devadr); 139 140 printf(PHY_NO" Initialized on %s\n", name); 141 } 142 143 void reset_phy(void) 144 { 145 mv_phy_init("egiga0"); 146 147 #ifdef CONFIG_BOARD_IS_OPENRD_CLIENT 148 /* Kirkwood ethernet driver is written with the assumption that in case 149 * of multiple PHYs, their addresses are consecutive. But unfortunately 150 * in case of OpenRD-Client, PHY addresses are not consecutive.*/ 151 miiphy_write("egiga1", 0xEE, 0xEE, 24); 152 #endif 153 154 #if defined(CONFIG_BOARD_IS_OPENRD_CLIENT) || \ 155 defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE) 156 /* configure and initialize both PHY's */ 157 mv_phy_init("egiga1"); 158 #endif 159 } 160 #endif /* CONFIG_RESET_PHY_R */ 161