1 /* 2 * (C) Copyright 2009 3 * Marvell Semiconductor <www.marvell.com> 4 * Written-by: Siddarth Gore <gores@marvell.com> 5 * 6 * See file CREDITS for list of people who contributed to this 7 * project. 8 * 9 * This program is free software; you can redistribute it and/or 10 * modify it under the terms of the GNU General Public License as 11 * published by the Free Software Foundation; either version 2 of 12 * the License, or (at your option) any later version. 13 * 14 * This program is distributed in the hope that it will be useful, 15 * but WITHOUT ANY WARRANTY; without even the implied warranty of 16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 17 * GNU General Public License for more details. 18 * 19 * You should have received a copy of the GNU General Public License 20 * along with this program; if not, write to the Free Software 21 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, 22 * MA 02110-1301 USA 23 */ 24 25 #include <common.h> 26 #include <miiphy.h> 27 #include <asm/arch/kirkwood.h> 28 #include <asm/arch/mpp.h> 29 #include "guruplug.h" 30 31 DECLARE_GLOBAL_DATA_PTR; 32 33 int board_init(void) 34 { 35 /* 36 * default gpio configuration 37 * There are maximum 64 gpios controlled through 2 sets of registers 38 * the below configuration configures mainly initial LED status 39 */ 40 kw_config_gpio(GURUPLUG_OE_VAL_LOW, 41 GURUPLUG_OE_VAL_HIGH, 42 GURUPLUG_OE_LOW, GURUPLUG_OE_HIGH); 43 44 /* Multi-Purpose Pins Functionality configuration */ 45 u32 kwmpp_config[] = { 46 MPP0_NF_IO2, 47 MPP1_NF_IO3, 48 MPP2_NF_IO4, 49 MPP3_NF_IO5, 50 MPP4_NF_IO6, 51 MPP5_NF_IO7, 52 MPP6_SYSRST_OUTn, 53 MPP7_GPO, /* GPIO_RST */ 54 MPP8_TW_SDA, 55 MPP9_TW_SCK, 56 MPP10_UART0_TXD, 57 MPP11_UART0_RXD, 58 MPP12_SD_CLK, 59 MPP13_SD_CMD, 60 MPP14_SD_D0, 61 MPP15_SD_D1, 62 MPP16_SD_D2, 63 MPP17_SD_D3, 64 MPP18_NF_IO0, 65 MPP19_NF_IO1, 66 MPP20_GE1_0, 67 MPP21_GE1_1, 68 MPP22_GE1_2, 69 MPP23_GE1_3, 70 MPP24_GE1_4, 71 MPP25_GE1_5, 72 MPP26_GE1_6, 73 MPP27_GE1_7, 74 MPP28_GE1_8, 75 MPP29_GE1_9, 76 MPP30_GE1_10, 77 MPP31_GE1_11, 78 MPP32_GE1_12, 79 MPP33_GE1_13, 80 MPP34_GE1_14, 81 MPP35_GE1_15, 82 MPP36_GPIO, 83 MPP37_GPIO, 84 MPP38_GPIO, 85 MPP39_GPIO, 86 MPP40_TDM_SPI_SCK, 87 MPP41_TDM_SPI_MISO, 88 MPP42_TDM_SPI_MOSI, 89 MPP43_GPIO, 90 MPP44_GPIO, 91 MPP45_GPIO, 92 MPP46_GPIO, /* M_RLED */ 93 MPP47_GPIO, /* M_GLED */ 94 MPP48_GPIO, /* B_RLED */ 95 MPP49_GPIO, /* B_GLED */ 96 0 97 }; 98 kirkwood_mpp_conf(kwmpp_config); 99 100 /* 101 * arch number of board 102 */ 103 gd->bd->bi_arch_number = MACH_TYPE_GURUPLUG; 104 105 /* adress of boot parameters */ 106 gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; 107 108 return 0; 109 } 110 111 int dram_init(void) 112 { 113 int i; 114 115 for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { 116 gd->bd->bi_dram[i].start = kw_sdram_bar(i); 117 gd->bd->bi_dram[i].size = kw_sdram_bs(i); 118 } 119 return 0; 120 } 121 122 #ifdef CONFIG_RESET_PHY_R 123 void mv_phy_88e1121_init(char *name) 124 { 125 u16 reg; 126 u16 devadr; 127 128 if (miiphy_set_current_dev(name)) 129 return; 130 131 /* command to read PHY dev address */ 132 if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { 133 printf("Err..%s could not read PHY dev address\n", 134 __FUNCTION__); 135 return; 136 } 137 138 /* 139 * Enable RGMII delay on Tx and Rx for CPU port 140 * Ref: sec 4.7.2 of chip datasheet 141 */ 142 miiphy_write(name, devadr, MV88E1121_PGADR_REG, 2); 143 miiphy_read(name, devadr, MV88E1121_MAC_CTRL2_REG, ®); 144 reg |= (MV88E1121_RGMII_RXTM_CTRL | MV88E1121_RGMII_TXTM_CTRL); 145 miiphy_write(name, devadr, MV88E1121_MAC_CTRL2_REG, reg); 146 miiphy_write(name, devadr, MV88E1121_PGADR_REG, 0); 147 148 /* reset the phy */ 149 miiphy_reset(name, devadr); 150 151 printf("88E1121 Initialized on %s\n", name); 152 } 153 154 void reset_phy(void) 155 { 156 /* configure and initialize both PHY's */ 157 mv_phy_88e1121_init("egiga0"); 158 mv_phy_88e1121_init("egiga1"); 159 } 160 #endif /* CONFIG_RESET_PHY_R */ 161