1 /*
2  * (C) Copyright 2009
3  * Marvell Semiconductor <www.marvell.com>
4  * Written-by: Siddarth Gore <gores@marvell.com>
5  *
6  * See file CREDITS for list of people who contributed to this
7  * project.
8  *
9  * This program is free software; you can redistribute it and/or
10  * modify it under the terms of the GNU General Public License as
11  * published by the Free Software Foundation; either version 2 of
12  * the License, or (at your option) any later version.
13  *
14  * This program is distributed in the hope that it will be useful,
15  * but WITHOUT ANY WARRANTY; without even the implied warranty of
16  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
17  * GNU General Public License for more details.
18  *
19  * You should have received a copy of the GNU General Public License
20  * along with this program; if not, write to the Free Software
21  * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
22  * MA 02110-1301 USA
23  */
24 
25 #include <common.h>
26 #include <miiphy.h>
27 #include <asm/arch/cpu.h>
28 #include <asm/arch/kirkwood.h>
29 #include <asm/arch/mpp.h>
30 #include "guruplug.h"
31 
32 DECLARE_GLOBAL_DATA_PTR;
33 
34 int board_early_init_f(void)
35 {
36 	/*
37 	 * default gpio configuration
38 	 * There are maximum 64 gpios controlled through 2 sets of registers
39 	 * the  below configuration configures mainly initial LED status
40 	 */
41 	kw_config_gpio(GURUPLUG_OE_VAL_LOW,
42 			GURUPLUG_OE_VAL_HIGH,
43 			GURUPLUG_OE_LOW, GURUPLUG_OE_HIGH);
44 
45 	/* Multi-Purpose Pins Functionality configuration */
46 	static const u32 kwmpp_config[] = {
47 		MPP0_NF_IO2,
48 		MPP1_NF_IO3,
49 		MPP2_NF_IO4,
50 		MPP3_NF_IO5,
51 		MPP4_NF_IO6,
52 		MPP5_NF_IO7,
53 		MPP6_SYSRST_OUTn,
54 		MPP7_GPO,	/* GPIO_RST */
55 		MPP8_TW_SDA,
56 		MPP9_TW_SCK,
57 		MPP10_UART0_TXD,
58 		MPP11_UART0_RXD,
59 		MPP12_SD_CLK,
60 		MPP13_SD_CMD,
61 		MPP14_SD_D0,
62 		MPP15_SD_D1,
63 		MPP16_SD_D2,
64 		MPP17_SD_D3,
65 		MPP18_NF_IO0,
66 		MPP19_NF_IO1,
67 		MPP20_GE1_0,
68 		MPP21_GE1_1,
69 		MPP22_GE1_2,
70 		MPP23_GE1_3,
71 		MPP24_GE1_4,
72 		MPP25_GE1_5,
73 		MPP26_GE1_6,
74 		MPP27_GE1_7,
75 		MPP28_GE1_8,
76 		MPP29_GE1_9,
77 		MPP30_GE1_10,
78 		MPP31_GE1_11,
79 		MPP32_GE1_12,
80 		MPP33_GE1_13,
81 		MPP34_GE1_14,
82 		MPP35_GE1_15,
83 		MPP36_GPIO,
84 		MPP37_GPIO,
85 		MPP38_GPIO,
86 		MPP39_GPIO,
87 		MPP40_TDM_SPI_SCK,
88 		MPP41_TDM_SPI_MISO,
89 		MPP42_TDM_SPI_MOSI,
90 		MPP43_GPIO,
91 		MPP44_GPIO,
92 		MPP45_GPIO,
93 		MPP46_GPIO, 	/* M_RLED */
94 		MPP47_GPIO,	/* M_GLED */
95 		MPP48_GPIO,	/* B_RLED */
96 		MPP49_GPIO,	/* B_GLED */
97 		0
98 	};
99 	kirkwood_mpp_conf(kwmpp_config, NULL);
100 	return 0;
101 }
102 
103 int board_init(void)
104 {
105 	/*
106 	 * arch number of board
107 	 */
108 	gd->bd->bi_arch_number = MACH_TYPE_GURUPLUG;
109 
110 	/* adress of boot parameters */
111 	gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
112 
113 	return 0;
114 }
115 
116 #ifdef CONFIG_RESET_PHY_R
117 void mv_phy_88e1121_init(char *name)
118 {
119 	u16 reg;
120 	u16 devadr;
121 
122 	if (miiphy_set_current_dev(name))
123 		return;
124 
125 	/* command to read PHY dev address */
126 	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
127 		printf("Err..%s could not read PHY dev address\n",
128 			__FUNCTION__);
129 		return;
130 	}
131 
132 	/*
133 	 * Enable RGMII delay on Tx and Rx for CPU port
134 	 * Ref: sec 4.7.2 of chip datasheet
135 	 */
136 	miiphy_write(name, devadr, MV88E1121_PGADR_REG, 2);
137 	miiphy_read(name, devadr, MV88E1121_MAC_CTRL2_REG, &reg);
138 	reg |= (MV88E1121_RGMII_RXTM_CTRL | MV88E1121_RGMII_TXTM_CTRL);
139 	miiphy_write(name, devadr, MV88E1121_MAC_CTRL2_REG, reg);
140 	miiphy_write(name, devadr, MV88E1121_PGADR_REG, 0);
141 
142 	/* reset the phy */
143 	miiphy_reset(name, devadr);
144 
145 	printf("88E1121 Initialized on %s\n", name);
146 }
147 
148 void reset_phy(void)
149 {
150 	/* configure and initialize both PHY's */
151 	mv_phy_88e1121_init("egiga0");
152 	mv_phy_88e1121_init("egiga1");
153 }
154 #endif /* CONFIG_RESET_PHY_R */
155