1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Copyright (C) 2015 Stefan Roese <sr@denx.de> 4 */ 5 6 #include <common.h> 7 #include <i2c.h> 8 #include <miiphy.h> 9 #include <netdev.h> 10 #include <asm/io.h> 11 #include <asm/arch/cpu.h> 12 #include <asm/arch/soc.h> 13 14 #include "../drivers/ddr/marvell/a38x/ddr3_init.h" 15 #include <../serdes/a38x/high_speed_env_spec.h> 16 17 DECLARE_GLOBAL_DATA_PTR; 18 19 #define ETH_PHY_CTRL_REG 0 20 #define ETH_PHY_CTRL_POWER_DOWN_BIT 11 21 #define ETH_PHY_CTRL_POWER_DOWN_MASK (1 << ETH_PHY_CTRL_POWER_DOWN_BIT) 22 23 /* 24 * Those values and defines are taken from the Marvell U-Boot version 25 * "u-boot-2013.01-2014_T3.0" 26 */ 27 #define DB_GP_88F68XX_GPP_OUT_ENA_LOW \ 28 (~(BIT(1) | BIT(4) | BIT(6) | BIT(7) | BIT(8) | BIT(9) | \ 29 BIT(10) | BIT(11) | BIT(19) | BIT(22) | BIT(23) | BIT(25) | \ 30 BIT(26) | BIT(27) | BIT(29) | BIT(30) | BIT(31))) 31 #define DB_GP_88F68XX_GPP_OUT_ENA_MID \ 32 (~(BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(15) | \ 33 BIT(16) | BIT(17) | BIT(18))) 34 35 #define DB_GP_88F68XX_GPP_OUT_VAL_LOW 0x0 36 #define DB_GP_88F68XX_GPP_OUT_VAL_MID 0x0 37 #define DB_GP_88F68XX_GPP_POL_LOW 0x0 38 #define DB_GP_88F68XX_GPP_POL_MID 0x0 39 40 /* IO expander on Marvell GP board includes e.g. fan enabling */ 41 struct marvell_io_exp { 42 u8 chip; 43 u8 addr; 44 u8 val; 45 }; 46 47 static struct marvell_io_exp io_exp[] = { 48 { 0x20, 6, 0x20 }, /* Configuration registers: Bit on --> Input bits */ 49 { 0x20, 7, 0xC3 }, /* Configuration registers: Bit on --> Input bits */ 50 { 0x20, 2, 0x1D }, /* Output Data, register#0 */ 51 { 0x20, 3, 0x18 }, /* Output Data, register#1 */ 52 { 0x21, 6, 0xC3 }, /* Configuration registers: Bit on --> Input bits */ 53 { 0x21, 7, 0x31 }, /* Configuration registers: Bit on --> Input bits */ 54 { 0x21, 2, 0x08 }, /* Output Data, register#0 */ 55 { 0x21, 3, 0xC0 } /* Output Data, register#1 */ 56 }; 57 58 static struct serdes_map board_serdes_map[] = { 59 {PEX0, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0}, 60 {SATA0, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0}, 61 {SATA1, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0}, 62 {SATA3, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0}, 63 {SATA2, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0}, 64 {USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0} 65 }; 66 67 int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count) 68 { 69 *serdes_map_array = board_serdes_map; 70 *count = ARRAY_SIZE(board_serdes_map); 71 return 0; 72 } 73 74 /* 75 * Define the DDR layout / topology here in the board file. This will 76 * be used by the DDR3 init code in the SPL U-Boot version to configure 77 * the DDR3 controller. 78 */ 79 static struct mv_ddr_topology_map board_topology_map = { 80 DEBUG_LEVEL_ERROR, 81 0x1, /* active interfaces */ 82 /* cs_mask, mirror, dqs_swap, ck_swap X PUPs */ 83 { { { {0x1, 0, 0, 0}, 84 {0x1, 0, 0, 0}, 85 {0x1, 0, 0, 0}, 86 {0x1, 0, 0, 0}, 87 {0x1, 0, 0, 0} }, 88 SPEED_BIN_DDR_1866L, /* speed_bin */ 89 MV_DDR_DEV_WIDTH_8BIT, /* memory_width */ 90 MV_DDR_DIE_CAP_4GBIT, /* mem_size */ 91 DDR_FREQ_800, /* frequency */ 92 0, 0, /* cas_wl cas_l */ 93 MV_DDR_TEMP_LOW, /* temperature */ 94 MV_DDR_TIM_DEFAULT} }, /* timing */ 95 BUS_MASK_32BIT, /* Busses mask */ 96 MV_DDR_CFG_DEFAULT, /* ddr configuration data source */ 97 { {0} }, /* raw spd data */ 98 {0} /* timing parameters */ 99 }; 100 101 struct mv_ddr_topology_map *mv_ddr_topology_map_get(void) 102 { 103 /* Return the board topology as defined in the board code */ 104 return &board_topology_map; 105 } 106 107 int board_early_init_f(void) 108 { 109 /* Configure MPP */ 110 writel(0x11111111, MVEBU_MPP_BASE + 0x00); 111 writel(0x11111111, MVEBU_MPP_BASE + 0x04); 112 writel(0x11244011, MVEBU_MPP_BASE + 0x08); 113 writel(0x22222111, MVEBU_MPP_BASE + 0x0c); 114 writel(0x22200002, MVEBU_MPP_BASE + 0x10); 115 writel(0x30042022, MVEBU_MPP_BASE + 0x14); 116 writel(0x55550555, MVEBU_MPP_BASE + 0x18); 117 writel(0x00005550, MVEBU_MPP_BASE + 0x1c); 118 119 /* Set GPP Out value */ 120 writel(DB_GP_88F68XX_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00); 121 writel(DB_GP_88F68XX_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00); 122 123 /* Set GPP Polarity */ 124 writel(DB_GP_88F68XX_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c); 125 writel(DB_GP_88F68XX_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c); 126 127 /* Set GPP Out Enable */ 128 writel(DB_GP_88F68XX_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04); 129 writel(DB_GP_88F68XX_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04); 130 131 return 0; 132 } 133 134 int board_init(void) 135 { 136 int i; 137 138 /* adress of boot parameters */ 139 gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; 140 141 /* Init I2C IO expanders */ 142 for (i = 0; i < ARRAY_SIZE(io_exp); i++) 143 i2c_write(io_exp[i].chip, io_exp[i].addr, 1, &io_exp[i].val, 1); 144 145 return 0; 146 } 147 148 int checkboard(void) 149 { 150 puts("Board: Marvell DB-88F6820-GP\n"); 151 152 return 0; 153 } 154 155 int board_eth_init(bd_t *bis) 156 { 157 cpu_eth_init(bis); /* Built in controller(s) come first */ 158 return pci_eth_init(bis); 159 } 160