1# SPDX-License-Identifier: GPL-2.0+ 2# 3# Copyright (C) 2015, Bin Meng <bmeng.cn@gmail.com> 4 5config INTEL_QUARK 6 bool 7 select HAVE_RMU 8 select ARCH_EARLY_INIT_R 9 select ARCH_MISC_INIT 10 imply ENABLE_MRC_CACHE 11 imply ETH_DESIGNWARE 12 imply ICH_SPI 13 imply INTEL_ICH6_GPIO 14 imply MMC 15 imply MMC_PCI 16 imply MMC_SDHCI 17 imply MMC_SDHCI_SDMA 18 imply SPI_FLASH 19 imply SYS_NS16550 20 imply USB 21 imply USB_EHCI_HCD 22 23if INTEL_QUARK 24 25config HAVE_RMU 26 bool "Add a Remote Management Unit (RMU) binary" 27 help 28 Select this option to add a Remote Management Unit (RMU) binary 29 to the resulting U-Boot image. It is a data block (up to 64K) of 30 machine-specific code which must be put in the flash for the RMU 31 within the Quark SoC processor to access when powered up before 32 system BIOS is executed. 33 34config RMU_FILE 35 string "Remote Management Unit (RMU) binary filename" 36 depends on HAVE_RMU 37 default "rmu.bin" 38 help 39 The filename of the file to use as Remote Management Unit (RMU) 40 binary in the board directory. 41 42config RMU_ADDR 43 hex "Remote Management Unit (RMU) binary location" 44 depends on HAVE_RMU 45 default 0xfff00000 46 help 47 The location of the RMU binary is determined by a strap. It must be 48 put in flash at a location matching the strap-determined base address. 49 50 The default base address of 0xfff00000 indicates that the binary must 51 be located at offset 0 from the beginning of a 1MB flash device. 52 53config HAVE_CMC 54 bool 55 default HAVE_RMU 56 57config CMC_FILE 58 string 59 depends on HAVE_CMC 60 default RMU_FILE 61 62config CMC_ADDR 63 hex 64 depends on HAVE_CMC 65 default RMU_ADDR 66 67config ESRAM_BASE 68 hex 69 default 0x80000000 70 help 71 Embedded SRAM (eSRAM) memory-mapped base address. 72 73config PCIE_ECAM_BASE 74 hex 75 default 0xe0000000 76 77config RCBA_BASE 78 hex 79 default 0xfed1c000 80 help 81 Root Complex register block memory-mapped base address. 82 83config ACPI_PM1_BASE 84 hex 85 default 0x1000 86 help 87 ACPI Power Management 1 (PM1) i/o-mapped base address. 88 This device is defined in ACPI specification, with 16 bytes in size. 89 90config ACPI_PBLK_BASE 91 hex 92 default 0x1010 93 help 94 ACPI Processor Block (PBLK) i/o-mapped base address. 95 This device is defined in ACPI specification, with 16 bytes in size. 96 97config SPI_DMA_BASE 98 hex 99 default 0x1020 100 help 101 SPI DMA i/o-mapped base address. 102 103config GPIO_BASE 104 hex 105 default 0x1080 106 help 107 GPIO i/o-mapped base address. 108 109config ACPI_GPE0_BASE 110 hex 111 default 0x1100 112 help 113 ACPI General Purpose Event 0 (GPE0) i/o-mapped base address. 114 This device is defined in ACPI specification, with 64 bytes in size. 115 116config WDT_BASE 117 hex 118 default 0x1140 119 help 120 Watchdog timer i/o-mapped base address. 121 122config SYS_CAR_ADDR 123 hex 124 default ESRAM_BASE 125 126config SYS_CAR_SIZE 127 hex 128 default 0x8000 129 help 130 Space in bytes in eSRAM used as Cache-As-ARM (CAR). 131 Note this size must not exceed eSRAM's total size. 132 133config X86_TSC_TIMER_EARLY_FREQ 134 int 135 default 400 136 137endif 138