1/* SPDX-License-Identifier: GPL-2.0+ */ 2/* 3 * Copyright 2004, 2007-2012 Freescale Semiconductor, Inc. 4 * Copyright (C) 2003 Motorola,Inc. 5 */ 6 7/* U-Boot Startup Code for Motorola 85xx PowerPC based Embedded Boards 8 * 9 * The processor starts at 0xfffffffc and the code is first executed in the 10 * last 4K page(0xfffff000-0xffffffff) in flash/rom. 11 * 12 */ 13 14#include <asm-offsets.h> 15#include <config.h> 16#include <mpc85xx.h> 17#include <version.h> 18 19#include <ppc_asm.tmpl> 20#include <ppc_defs.h> 21 22#include <asm/cache.h> 23#include <asm/mmu.h> 24 25#undef MSR_KERNEL 26#define MSR_KERNEL ( MSR_ME ) /* Machine Check */ 27 28#define LAW_EN 0x80000000 29 30#if defined(CONFIG_NAND_SPL) || \ 31 (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL)) 32#define MINIMAL_SPL 33#endif 34 35#if !defined(CONFIG_SPL) && !defined(CONFIG_SYS_RAMBOOT) && \ 36 !defined(CONFIG_SECURE_BOOT) && !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 37#define NOR_BOOT 38#endif 39 40/* 41 * Set up GOT: Global Offset Table 42 * 43 * Use r12 to access the GOT 44 */ 45 START_GOT 46 GOT_ENTRY(_GOT2_TABLE_) 47 GOT_ENTRY(_FIXUP_TABLE_) 48 49#ifndef MINIMAL_SPL 50 GOT_ENTRY(_start) 51 GOT_ENTRY(_start_of_vectors) 52 GOT_ENTRY(_end_of_vectors) 53 GOT_ENTRY(transfer_to_handler) 54#endif 55 56 GOT_ENTRY(__init_end) 57 GOT_ENTRY(__bss_end) 58 GOT_ENTRY(__bss_start) 59 END_GOT 60 61/* 62 * e500 Startup -- after reset only the last 4KB of the effective 63 * address space is mapped in the MMU L2 TLB1 Entry0. The .bootpg 64 * section is located at THIS LAST page and basically does three 65 * things: clear some registers, set up exception tables and 66 * add more TLB entries for 'larger spaces'(e.g. the boot rom) to 67 * continue the boot procedure. 68 69 * Once the boot rom is mapped by TLB entries we can proceed 70 * with normal startup. 71 * 72 */ 73 74 .section .bootpg,"ax" 75 .globl _start_e500 76 77_start_e500: 78/* Enable debug exception */ 79 li r1,MSR_DE 80 mtmsr r1 81 82 /* 83 * If we got an ePAPR device tree pointer passed in as r3, we need that 84 * later in cpu_init_early_f(). Save it to a safe register before we 85 * clobber it so that we can fetch it from there later. 86 */ 87 mr r24, r3 88 89#ifdef CONFIG_SYS_FSL_ERRATUM_A004510 90 mfspr r3,SPRN_SVR 91 rlwinm r3,r3,0,0xff 92 li r4,CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV 93 cmpw r3,r4 94 beq 1f 95 96#ifdef CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 97 li r4,CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 98 cmpw r3,r4 99 beq 1f 100#endif 101 102 /* Not a supported revision affected by erratum */ 103 li r27,0 104 b 2f 105 1061: li r27,1 /* Remember for later that we have the erratum */ 107 /* Erratum says set bits 55:60 to 001001 */ 108 msync 109 isync 110 mfspr r3,SPRN_HDBCR0 111 li r4,0x48 112 rlwimi r3,r4,0,0x1f8 113 mtspr SPRN_HDBCR0,r3 114 isync 1152: 116#endif 117#ifdef CONFIG_SYS_FSL_ERRATUM_A005125 118 msync 119 isync 120 mfspr r3, SPRN_HDBCR0 121 oris r3, r3, 0x0080 122 mtspr SPRN_HDBCR0, r3 123#endif 124 125 126#if defined(CONFIG_SECURE_BOOT) && defined(CONFIG_E500MC) && \ 127 !defined(CONFIG_E6500) 128 /* ISBC uses L2 as stack. 129 * Disable L2 cache here so that u-boot can enable it later 130 * as part of it's normal flow 131 */ 132 133 /* Check if L2 is enabled */ 134 mfspr r3, SPRN_L2CSR0 135 lis r2, L2CSR0_L2E@h 136 ori r2, r2, L2CSR0_L2E@l 137 and. r4, r3, r2 138 beq l2_disabled 139 140 mfspr r3, SPRN_L2CSR0 141 /* Flush L2 cache */ 142 lis r2,(L2CSR0_L2FL)@h 143 ori r2, r2, (L2CSR0_L2FL)@l 144 or r3, r2, r3 145 sync 146 isync 147 mtspr SPRN_L2CSR0,r3 148 isync 1491: 150 mfspr r3, SPRN_L2CSR0 151 and. r1, r3, r2 152 bne 1b 153 154 mfspr r3, SPRN_L2CSR0 155 lis r2, L2CSR0_L2E@h 156 ori r2, r2, L2CSR0_L2E@l 157 andc r4, r3, r2 158 sync 159 isync 160 mtspr SPRN_L2CSR0,r4 161 isync 162 163l2_disabled: 164#endif 165 166/* clear registers/arrays not reset by hardware */ 167 168 /* L1 */ 169 li r0,2 170 mtspr L1CSR0,r0 /* invalidate d-cache */ 171 mtspr L1CSR1,r0 /* invalidate i-cache */ 172 173 mfspr r1,DBSR 174 mtspr DBSR,r1 /* Clear all valid bits */ 175 176 177 .macro create_tlb1_entry esel ts tsize epn wimg rpn perm phy_high scratch 178 lis \scratch, FSL_BOOKE_MAS0(1, \esel, 0)@h 179 ori \scratch, \scratch, FSL_BOOKE_MAS0(1, \esel, 0)@l 180 mtspr MAS0, \scratch 181 lis \scratch, FSL_BOOKE_MAS1(1, 1, 0, \ts, \tsize)@h 182 ori \scratch, \scratch, FSL_BOOKE_MAS1(1, 1, 0, \ts, \tsize)@l 183 mtspr MAS1, \scratch 184 lis \scratch, FSL_BOOKE_MAS2(\epn, \wimg)@h 185 ori \scratch, \scratch, FSL_BOOKE_MAS2(\epn, \wimg)@l 186 mtspr MAS2, \scratch 187 lis \scratch, FSL_BOOKE_MAS3(\rpn, 0, \perm)@h 188 ori \scratch, \scratch, FSL_BOOKE_MAS3(\rpn, 0, \perm)@l 189 mtspr MAS3, \scratch 190 lis \scratch, \phy_high@h 191 ori \scratch, \scratch, \phy_high@l 192 mtspr MAS7, \scratch 193 isync 194 msync 195 tlbwe 196 isync 197 .endm 198 199 .macro create_tlb0_entry esel ts tsize epn wimg rpn perm phy_high scratch 200 lis \scratch, FSL_BOOKE_MAS0(0, \esel, 0)@h 201 ori \scratch, \scratch, FSL_BOOKE_MAS0(0, \esel, 0)@l 202 mtspr MAS0, \scratch 203 lis \scratch, FSL_BOOKE_MAS1(1, 0, 0, \ts, \tsize)@h 204 ori \scratch, \scratch, FSL_BOOKE_MAS1(1, 0, 0, \ts, \tsize)@l 205 mtspr MAS1, \scratch 206 lis \scratch, FSL_BOOKE_MAS2(\epn, \wimg)@h 207 ori \scratch, \scratch, FSL_BOOKE_MAS2(\epn, \wimg)@l 208 mtspr MAS2, \scratch 209 lis \scratch, FSL_BOOKE_MAS3(\rpn, 0, \perm)@h 210 ori \scratch, \scratch, FSL_BOOKE_MAS3(\rpn, 0, \perm)@l 211 mtspr MAS3, \scratch 212 lis \scratch, \phy_high@h 213 ori \scratch, \scratch, \phy_high@l 214 mtspr MAS7, \scratch 215 isync 216 msync 217 tlbwe 218 isync 219 .endm 220 221 .macro delete_tlb1_entry esel scratch 222 lis \scratch, FSL_BOOKE_MAS0(1, \esel, 0)@h 223 ori \scratch, \scratch, FSL_BOOKE_MAS0(1, \esel, 0)@l 224 mtspr MAS0, \scratch 225 li \scratch, 0 226 mtspr MAS1, \scratch 227 isync 228 msync 229 tlbwe 230 isync 231 .endm 232 233 .macro delete_tlb0_entry esel epn wimg scratch 234 lis \scratch, FSL_BOOKE_MAS0(0, \esel, 0)@h 235 ori \scratch, \scratch, FSL_BOOKE_MAS0(0, \esel, 0)@l 236 mtspr MAS0, \scratch 237 li \scratch, 0 238 mtspr MAS1, \scratch 239 lis \scratch, FSL_BOOKE_MAS2(\epn, \wimg)@h 240 ori \scratch, \scratch, FSL_BOOKE_MAS2(\epn, \wimg)@l 241 mtspr MAS2, \scratch 242 isync 243 msync 244 tlbwe 245 isync 246 .endm 247 248/* Interrupt vectors do not fit in minimal SPL. */ 249#if !defined(MINIMAL_SPL) 250 /* Setup interrupt vectors */ 251 lis r1,CONFIG_SYS_MONITOR_BASE@h 252 mtspr IVPR,r1 253 254 li r4,CriticalInput@l 255 mtspr IVOR0,r4 /* 0: Critical input */ 256 li r4,MachineCheck@l 257 mtspr IVOR1,r4 /* 1: Machine check */ 258 li r4,DataStorage@l 259 mtspr IVOR2,r4 /* 2: Data storage */ 260 li r4,InstStorage@l 261 mtspr IVOR3,r4 /* 3: Instruction storage */ 262 li r4,ExtInterrupt@l 263 mtspr IVOR4,r4 /* 4: External interrupt */ 264 li r4,Alignment@l 265 mtspr IVOR5,r4 /* 5: Alignment */ 266 li r4,ProgramCheck@l 267 mtspr IVOR6,r4 /* 6: Program check */ 268 li r4,FPUnavailable@l 269 mtspr IVOR7,r4 /* 7: floating point unavailable */ 270 li r4,SystemCall@l 271 mtspr IVOR8,r4 /* 8: System call */ 272 /* 9: Auxiliary processor unavailable(unsupported) */ 273 li r4,Decrementer@l 274 mtspr IVOR10,r4 /* 10: Decrementer */ 275 li r4,IntervalTimer@l 276 mtspr IVOR11,r4 /* 11: Interval timer */ 277 li r4,WatchdogTimer@l 278 mtspr IVOR12,r4 /* 12: Watchdog timer */ 279 li r4,DataTLBError@l 280 mtspr IVOR13,r4 /* 13: Data TLB error */ 281 li r4,InstructionTLBError@l 282 mtspr IVOR14,r4 /* 14: Instruction TLB error */ 283 li r4,DebugBreakpoint@l 284 mtspr IVOR15,r4 /* 15: Debug */ 285#endif 286 287 /* Clear and set up some registers. */ 288 li r0,0x0000 289 lis r1,0xffff 290 mtspr DEC,r0 /* prevent dec exceptions */ 291 mttbl r0 /* prevent fit & wdt exceptions */ 292 mttbu r0 293 mtspr TSR,r1 /* clear all timer exception status */ 294 mtspr TCR,r0 /* disable all */ 295 mtspr ESR,r0 /* clear exception syndrome register */ 296 mtspr MCSR,r0 /* machine check syndrome register */ 297 mtxer r0 /* clear integer exception register */ 298 299#ifdef CONFIG_SYS_BOOK3E_HV 300 mtspr MAS8,r0 /* make sure MAS8 is clear */ 301#endif 302 303 /* Enable Time Base and Select Time Base Clock */ 304 lis r0,HID0_EMCP@h /* Enable machine check */ 305#if defined(CONFIG_ENABLE_36BIT_PHYS) 306 ori r0,r0,HID0_ENMAS7@l /* Enable MAS7 */ 307#endif 308#ifndef CONFIG_E500MC 309 ori r0,r0,HID0_TBEN@l /* Enable Timebase */ 310#endif 311 mtspr HID0,r0 312 313#if !defined(CONFIG_E500MC) && !defined(CONFIG_ARCH_QEMU_E500) 314 li r0,(HID1_ASTME|HID1_ABE)@l /* Addr streaming & broadcast */ 315 mfspr r3,PVR 316 andi. r3,r3, 0xff 317 cmpwi r3,0x50@l /* if we are rev 5.0 or greater set MBDD */ 318 blt 1f 319 /* Set MBDD bit also */ 320 ori r0, r0, HID1_MBDD@l 3211: 322 mtspr HID1,r0 323#endif 324 325#ifdef CONFIG_SYS_FSL_ERRATUM_CPU_A003999 326 mfspr r3,SPRN_HDBCR1 327 oris r3,r3,0x0100 328 mtspr SPRN_HDBCR1,r3 329#endif 330 331 /* Enable Branch Prediction */ 332#if defined(CONFIG_BTB) 333 lis r0,BUCSR_ENABLE@h 334 ori r0,r0,BUCSR_ENABLE@l 335 mtspr SPRN_BUCSR,r0 336#endif 337 338#if defined(CONFIG_SYS_INIT_DBCR) 339 lis r1,0xffff 340 ori r1,r1,0xffff 341 mtspr DBSR,r1 /* Clear all status bits */ 342 lis r0,CONFIG_SYS_INIT_DBCR@h /* DBCR0[IDM] must be set */ 343 ori r0,r0,CONFIG_SYS_INIT_DBCR@l 344 mtspr DBCR0,r0 345#endif 346 347#ifdef CONFIG_ARCH_MPC8569 348#define CONFIG_SYS_LBC_ADDR (CONFIG_SYS_CCSRBAR_DEFAULT + 0x5000) 349#define CONFIG_SYS_LBCR_ADDR (CONFIG_SYS_LBC_ADDR + 0xd0) 350 351 /* MPC8569 Rev.0 silcon needs to set bit 13 of LBCR to allow elBC to 352 * use address space which is more than 12bits, and it must be done in 353 * the 4K boot page. So we set this bit here. 354 */ 355 356 /* create a temp mapping TLB0[0] for LBCR */ 357 create_tlb0_entry 0, \ 358 0, BOOKE_PAGESZ_4K, \ 359 CONFIG_SYS_LBC_ADDR, MAS2_I|MAS2_G, \ 360 CONFIG_SYS_LBC_ADDR, MAS3_SW|MAS3_SR, \ 361 0, r6 362 363 /* Set LBCR register */ 364 lis r4,CONFIG_SYS_LBCR_ADDR@h 365 ori r4,r4,CONFIG_SYS_LBCR_ADDR@l 366 367 lis r5,CONFIG_SYS_LBC_LBCR@h 368 ori r5,r5,CONFIG_SYS_LBC_LBCR@l 369 stw r5,0(r4) 370 isync 371 372 /* invalidate this temp TLB */ 373 lis r4,CONFIG_SYS_LBC_ADDR@h 374 ori r4,r4,CONFIG_SYS_LBC_ADDR@l 375 tlbivax 0,r4 376 isync 377 378#endif /* CONFIG_ARCH_MPC8569 */ 379 380/* 381 * Search for the TLB that covers the code we're executing, and shrink it 382 * so that it covers only this 4K page. That will ensure that any other 383 * TLB we create won't interfere with it. We assume that the TLB exists, 384 * which is why we don't check the Valid bit of MAS1. We also assume 385 * it is in TLB1. 386 * 387 * This is necessary, for example, when booting from the on-chip ROM, 388 * which (oddly) creates a single 4GB TLB that covers CCSR and DDR. 389 */ 390 bl nexti /* Find our address */ 391nexti: mflr r1 /* R1 = our PC */ 392 li r2, 0 393 mtspr MAS6, r2 /* Assume the current PID and AS are 0 */ 394 isync 395 msync 396 tlbsx 0, r1 /* This must succeed */ 397 398 mfspr r14, MAS0 /* Save ESEL for later */ 399 rlwinm r14, r14, 16, 0xfff 400 401 /* Set the size of the TLB to 4KB */ 402 mfspr r3, MAS1 403 li r2, 0xF80 404 andc r3, r3, r2 /* Clear the TSIZE bits */ 405 ori r3, r3, MAS1_TSIZE(BOOKE_PAGESZ_4K)@l 406 oris r3, r3, MAS1_IPROT@h 407 mtspr MAS1, r3 408 409 /* 410 * Set the base address of the TLB to our PC. We assume that 411 * virtual == physical. We also assume that MAS2_EPN == MAS3_RPN. 412 */ 413 lis r3, MAS2_EPN@h 414 ori r3, r3, MAS2_EPN@l /* R3 = MAS2_EPN */ 415 416 and r1, r1, r3 /* Our PC, rounded down to the nearest page */ 417 418 mfspr r2, MAS2 419 andc r2, r2, r3 420 or r2, r2, r1 421#ifdef CONFIG_SYS_FSL_ERRATUM_A004510 422 cmpwi r27,0 423 beq 1f 424 andi. r15, r2, MAS2_I|MAS2_G /* save the old I/G for later */ 425 rlwinm r2, r2, 0, ~MAS2_I 426 ori r2, r2, MAS2_G 4271: 428#endif 429 mtspr MAS2, r2 /* Set the EPN to our PC base address */ 430 431 mfspr r2, MAS3 432 andc r2, r2, r3 433 or r2, r2, r1 434 mtspr MAS3, r2 /* Set the RPN to our PC base address */ 435 436 isync 437 msync 438 tlbwe 439 440/* 441 * Clear out any other TLB entries that may exist, to avoid conflicts. 442 * Our TLB entry is in r14. 443 */ 444 li r0, TLBIVAX_ALL | TLBIVAX_TLB0 445 tlbivax 0, r0 446 tlbsync 447 448 mfspr r4, SPRN_TLB1CFG 449 rlwinm r4, r4, 0, TLBnCFG_NENTRY_MASK 450 451 li r3, 0 452 mtspr MAS1, r3 4531: cmpw r3, r14 454 rlwinm r5, r3, 16, MAS0_ESEL_MSK 455 addi r3, r3, 1 456 beq 2f /* skip the entry we're executing from */ 457 458 oris r5, r5, MAS0_TLBSEL(1)@h 459 mtspr MAS0, r5 460 461 isync 462 tlbwe 463 isync 464 msync 465 4662: cmpw r3, r4 467 blt 1b 468 469#if defined(CONFIG_SYS_PPC_E500_DEBUG_TLB) && !defined(MINIMAL_SPL) && \ 470 !defined(CONFIG_SECURE_BOOT) 471/* 472 * TLB entry for debuggging in AS1 473 * Create temporary TLB entry in AS0 to handle debug exception 474 * As on debug exception MSR is cleared i.e. Address space is changed 475 * to 0. A TLB entry (in AS0) is required to handle debug exception generated 476 * in AS1. 477 */ 478 479#ifdef NOR_BOOT 480/* 481 * TLB entry is created for IVPR + IVOR15 to map on valid OP code address 482 * bacause flash's virtual address maps to 0xff800000 - 0xffffffff. 483 * and this window is outside of 4K boot window. 484 */ 485 create_tlb1_entry CONFIG_SYS_PPC_E500_DEBUG_TLB, \ 486 0, BOOKE_PAGESZ_4M, \ 487 CONFIG_SYS_MONITOR_BASE & 0xffc00000, MAS2_I|MAS2_G, \ 488 0xffc00000, MAS3_SX|MAS3_SW|MAS3_SR, \ 489 0, r6 490 491#else 492/* 493 * TLB entry is created for IVPR + IVOR15 to map on valid OP code address 494 * because "nexti" will resize TLB to 4K 495 */ 496 create_tlb1_entry CONFIG_SYS_PPC_E500_DEBUG_TLB, \ 497 0, BOOKE_PAGESZ_256K, \ 498 CONFIG_SYS_MONITOR_BASE & 0xfffc0000, MAS2_I, \ 499 CONFIG_SYS_MONITOR_BASE & 0xfffc0000, MAS3_SX|MAS3_SW|MAS3_SR, \ 500 0, r6 501#endif 502#endif 503 504/* 505 * Relocate CCSR, if necessary. We relocate CCSR if (obviously) the default 506 * location is not where we want it. This typically happens on a 36-bit 507 * system, where we want to move CCSR to near the top of 36-bit address space. 508 * 509 * To move CCSR, we create two temporary TLBs, one for the old location, and 510 * another for the new location. On CoreNet systems, we also need to create 511 * a special, temporary LAW. 512 * 513 * As a general rule, TLB0 is used for short-term TLBs, and TLB1 is used for 514 * long-term TLBs, so we use TLB0 here. 515 */ 516#if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR_PHYS) 517 518#if !defined(CONFIG_SYS_CCSRBAR_PHYS_HIGH) || !defined(CONFIG_SYS_CCSRBAR_PHYS_LOW) 519#error "CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW) must be defined." 520#endif 521 522create_ccsr_new_tlb: 523 /* 524 * Create a TLB for the new location of CCSR. Register R8 is reserved 525 * for the virtual address of this TLB (CONFIG_SYS_CCSRBAR). 526 */ 527 lis r8, CONFIG_SYS_CCSRBAR@h 528 ori r8, r8, CONFIG_SYS_CCSRBAR@l 529 lis r9, (CONFIG_SYS_CCSRBAR + 0x1000)@h 530 ori r9, r9, (CONFIG_SYS_CCSRBAR + 0x1000)@l 531 create_tlb0_entry 0, \ 532 0, BOOKE_PAGESZ_4K, \ 533 CONFIG_SYS_CCSRBAR, MAS2_I|MAS2_G, \ 534 CONFIG_SYS_CCSRBAR_PHYS_LOW, MAS3_SW|MAS3_SR, \ 535 CONFIG_SYS_CCSRBAR_PHYS_HIGH, r3 536 /* 537 * Create a TLB for the current location of CCSR. Register R9 is reserved 538 * for the virtual address of this TLB (CONFIG_SYS_CCSRBAR + 0x1000). 539 */ 540create_ccsr_old_tlb: 541 create_tlb0_entry 1, \ 542 0, BOOKE_PAGESZ_4K, \ 543 CONFIG_SYS_CCSRBAR + 0x1000, MAS2_I|MAS2_G, \ 544 CONFIG_SYS_CCSRBAR_DEFAULT, MAS3_SW|MAS3_SR, \ 545 0, r3 /* The default CCSR address is always a 32-bit number */ 546 547 548 /* 549 * We have a TLB for what we think is the current (old) CCSR. Let's 550 * verify that, otherwise we won't be able to move it. 551 * CONFIG_SYS_CCSRBAR_DEFAULT is always a 32-bit number, so we only 552 * need to compare the lower 32 bits of CCSRBAR on CoreNet systems. 553 */ 554verify_old_ccsr: 555 lis r0, CONFIG_SYS_CCSRBAR_DEFAULT@h 556 ori r0, r0, CONFIG_SYS_CCSRBAR_DEFAULT@l 557#ifdef CONFIG_FSL_CORENET 558 lwz r1, 4(r9) /* CCSRBARL */ 559#else 560 lwz r1, 0(r9) /* CCSRBAR, shifted right by 12 */ 561 slwi r1, r1, 12 562#endif 563 564 cmpl 0, r0, r1 565 566 /* 567 * If the value we read from CCSRBARL is not what we expect, then 568 * enter an infinite loop. This will at least allow a debugger to 569 * halt execution and examine TLBs, etc. There's no point in going 570 * on. 571 */ 572infinite_debug_loop: 573 bne infinite_debug_loop 574 575#ifdef CONFIG_FSL_CORENET 576 577#define CCSR_LAWBARH0 (CONFIG_SYS_CCSRBAR + 0x1000) 578#define LAW_SIZE_4K 0xb 579#define CCSRBAR_LAWAR (LAW_EN | (0x1e << 20) | LAW_SIZE_4K) 580#define CCSRAR_C 0x80000000 /* Commit */ 581 582create_temp_law: 583 /* 584 * On CoreNet systems, we create the temporary LAW using a special LAW 585 * target ID of 0x1e. LAWBARH is at offset 0xc00 in CCSR. 586 */ 587 lis r0, CONFIG_SYS_CCSRBAR_PHYS_HIGH@h 588 ori r0, r0, CONFIG_SYS_CCSRBAR_PHYS_HIGH@l 589 lis r1, CONFIG_SYS_CCSRBAR_PHYS_LOW@h 590 ori r1, r1, CONFIG_SYS_CCSRBAR_PHYS_LOW@l 591 lis r2, CCSRBAR_LAWAR@h 592 ori r2, r2, CCSRBAR_LAWAR@l 593 594 stw r0, 0xc00(r9) /* LAWBARH0 */ 595 stw r1, 0xc04(r9) /* LAWBARL0 */ 596 sync 597 stw r2, 0xc08(r9) /* LAWAR0 */ 598 599 /* 600 * Read back from LAWAR to ensure the update is complete. e500mc 601 * cores also require an isync. 602 */ 603 lwz r0, 0xc08(r9) /* LAWAR0 */ 604 isync 605 606 /* 607 * Read the current CCSRBARH and CCSRBARL using load word instructions. 608 * Follow this with an isync instruction. This forces any outstanding 609 * accesses to configuration space to completion. 610 */ 611read_old_ccsrbar: 612 lwz r0, 0(r9) /* CCSRBARH */ 613 lwz r0, 4(r9) /* CCSRBARL */ 614 isync 615 616 /* 617 * Write the new values for CCSRBARH and CCSRBARL to their old 618 * locations. The CCSRBARH has a shadow register. When the CCSRBARH 619 * has a new value written it loads a CCSRBARH shadow register. When 620 * the CCSRBARL is written, the CCSRBARH shadow register contents 621 * along with the CCSRBARL value are loaded into the CCSRBARH and 622 * CCSRBARL registers, respectively. Follow this with a sync 623 * instruction. 624 */ 625write_new_ccsrbar: 626 lis r0, CONFIG_SYS_CCSRBAR_PHYS_HIGH@h 627 ori r0, r0, CONFIG_SYS_CCSRBAR_PHYS_HIGH@l 628 lis r1, CONFIG_SYS_CCSRBAR_PHYS_LOW@h 629 ori r1, r1, CONFIG_SYS_CCSRBAR_PHYS_LOW@l 630 lis r2, CCSRAR_C@h 631 ori r2, r2, CCSRAR_C@l 632 633 stw r0, 0(r9) /* Write to CCSRBARH */ 634 sync /* Make sure we write to CCSRBARH first */ 635 stw r1, 4(r9) /* Write to CCSRBARL */ 636 sync 637 638 /* 639 * Write a 1 to the commit bit (C) of CCSRAR at the old location. 640 * Follow this with a sync instruction. 641 */ 642 stw r2, 8(r9) 643 sync 644 645 /* Delete the temporary LAW */ 646delete_temp_law: 647 li r1, 0 648 stw r1, 0xc08(r8) 649 sync 650 stw r1, 0xc00(r8) 651 stw r1, 0xc04(r8) 652 sync 653 654#else /* #ifdef CONFIG_FSL_CORENET */ 655 656write_new_ccsrbar: 657 /* 658 * Read the current value of CCSRBAR using a load word instruction 659 * followed by an isync. This forces all accesses to configuration 660 * space to complete. 661 */ 662 sync 663 lwz r0, 0(r9) 664 isync 665 666/* CONFIG_SYS_CCSRBAR_PHYS right shifted by 12 */ 667#define CCSRBAR_PHYS_RS12 ((CONFIG_SYS_CCSRBAR_PHYS_HIGH << 20) | \ 668 (CONFIG_SYS_CCSRBAR_PHYS_LOW >> 12)) 669 670 /* Write the new value to CCSRBAR. */ 671 lis r0, CCSRBAR_PHYS_RS12@h 672 ori r0, r0, CCSRBAR_PHYS_RS12@l 673 stw r0, 0(r9) 674 sync 675 676 /* 677 * The manual says to perform a load of an address that does not 678 * access configuration space or the on-chip SRAM using an existing TLB, 679 * but that doesn't appear to be necessary. We will do the isync, 680 * though. 681 */ 682 isync 683 684 /* 685 * Read the contents of CCSRBAR from its new location, followed by 686 * another isync. 687 */ 688 lwz r0, 0(r8) 689 isync 690 691#endif /* #ifdef CONFIG_FSL_CORENET */ 692 693 /* Delete the temporary TLBs */ 694delete_temp_tlbs: 695 delete_tlb0_entry 0, CONFIG_SYS_CCSRBAR, MAS2_I|MAS2_G, r3 696 delete_tlb0_entry 1, CONFIG_SYS_CCSRBAR + 0x1000, MAS2_I|MAS2_G, r3 697 698#endif /* #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR_PHYS) */ 699 700#if defined(CONFIG_SYS_FSL_QORIQ_CHASSIS2) && defined(CONFIG_E6500) 701create_ccsr_l2_tlb: 702 /* 703 * Create a TLB for the MMR location of CCSR 704 * to access L2CSR0 register 705 */ 706 create_tlb0_entry 0, \ 707 0, BOOKE_PAGESZ_4K, \ 708 CONFIG_SYS_CCSRBAR + 0xC20000, MAS2_I|MAS2_G, \ 709 CONFIG_SYS_CCSRBAR_PHYS_LOW + 0xC20000, MAS3_SW|MAS3_SR, \ 710 CONFIG_SYS_CCSRBAR_PHYS_HIGH, r3 711 712enable_l2_cluster_l2: 713 /* enable L2 cache */ 714 lis r3, (CONFIG_SYS_CCSRBAR + 0xC20000)@h 715 ori r3, r3, (CONFIG_SYS_CCSRBAR + 0xC20000)@l 716 li r4, 33 /* stash id */ 717 stw r4, 4(r3) 718 lis r4, (L2CSR0_L2FI|L2CSR0_L2LFC)@h 719 ori r4, r4, (L2CSR0_L2FI|L2CSR0_L2LFC)@l 720 sync 721 stw r4, 0(r3) /* invalidate L2 */ 722 /* Poll till the bits are cleared */ 7231: sync 724 lwz r0, 0(r3) 725 twi 0, r0, 0 726 isync 727 and. r1, r0, r4 728 bne 1b 729 730 /* L2PE must be set before L2 cache is enabled */ 731 lis r4, (L2CSR0_L2PE)@h 732 ori r4, r4, (L2CSR0_L2PE)@l 733 sync 734 stw r4, 0(r3) /* enable L2 parity/ECC error checking */ 735 /* Poll till the bit is set */ 7361: sync 737 lwz r0, 0(r3) 738 twi 0, r0, 0 739 isync 740 and. r1, r0, r4 741 beq 1b 742 743 lis r4, (L2CSR0_L2E|L2CSR0_L2PE)@h 744 ori r4, r4, (L2CSR0_L2REP_MODE)@l 745 sync 746 stw r4, 0(r3) /* enable L2 */ 747 /* Poll till the bit is set */ 7481: sync 749 lwz r0, 0(r3) 750 twi 0, r0, 0 751 isync 752 and. r1, r0, r4 753 beq 1b 754 755delete_ccsr_l2_tlb: 756 delete_tlb0_entry 0, CONFIG_SYS_CCSRBAR + 0xC20000, MAS2_I|MAS2_G, r3 757#endif 758 759 /* 760 * Enable the L1. On e6500, this has to be done 761 * after the L2 is up. 762 */ 763 764#ifdef CONFIG_SYS_CACHE_STASHING 765 /* set stash id to (coreID) * 2 + 32 + L1 CT (0) */ 766 li r2,(32 + 0) 767 mtspr L1CSR2,r2 768#endif 769 770 /* Enable/invalidate the I-Cache */ 771 lis r2,(L1CSR1_ICFI|L1CSR1_ICLFR)@h 772 ori r2,r2,(L1CSR1_ICFI|L1CSR1_ICLFR)@l 773 mtspr SPRN_L1CSR1,r2 7741: 775 mfspr r3,SPRN_L1CSR1 776 and. r1,r3,r2 777 bne 1b 778 779 lis r3,(L1CSR1_CPE|L1CSR1_ICE)@h 780 ori r3,r3,(L1CSR1_CPE|L1CSR1_ICE)@l 781 mtspr SPRN_L1CSR1,r3 782 isync 7832: 784 mfspr r3,SPRN_L1CSR1 785 andi. r1,r3,L1CSR1_ICE@l 786 beq 2b 787 788 /* Enable/invalidate the D-Cache */ 789 lis r2,(L1CSR0_DCFI|L1CSR0_DCLFR)@h 790 ori r2,r2,(L1CSR0_DCFI|L1CSR0_DCLFR)@l 791 mtspr SPRN_L1CSR0,r2 7921: 793 mfspr r3,SPRN_L1CSR0 794 and. r1,r3,r2 795 bne 1b 796 797 lis r3,(L1CSR0_CPE|L1CSR0_DCE)@h 798 ori r3,r3,(L1CSR0_CPE|L1CSR0_DCE)@l 799 mtspr SPRN_L1CSR0,r3 800 isync 8012: 802 mfspr r3,SPRN_L1CSR0 803 andi. r1,r3,L1CSR0_DCE@l 804 beq 2b 805#ifdef CONFIG_SYS_FSL_ERRATUM_A004510 806#define DCSR_LAWBARH0 (CONFIG_SYS_CCSRBAR + 0x1000) 807#define LAW_SIZE_1M 0x13 808#define DCSRBAR_LAWAR (LAW_EN | (0x1d << 20) | LAW_SIZE_1M) 809 810 cmpwi r27,0 811 beq 9f 812 813 /* 814 * Create a TLB entry for CCSR 815 * 816 * We're executing out of TLB1 entry in r14, and that's the only 817 * TLB entry that exists. To allocate some TLB entries for our 818 * own use, flip a bit high enough that we won't flip it again 819 * via incrementing. 820 */ 821 822 xori r8, r14, 32 823 lis r0, MAS0_TLBSEL(1)@h 824 rlwimi r0, r8, 16, MAS0_ESEL_MSK 825 lis r1, FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)@h 826 ori r1, r1, FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)@l 827 lis r7, CONFIG_SYS_CCSRBAR@h 828 ori r7, r7, CONFIG_SYS_CCSRBAR@l 829 ori r2, r7, MAS2_I|MAS2_G 830 lis r3, FSL_BOOKE_MAS3(CONFIG_SYS_CCSRBAR_PHYS_LOW, 0, (MAS3_SW|MAS3_SR))@h 831 ori r3, r3, FSL_BOOKE_MAS3(CONFIG_SYS_CCSRBAR_PHYS_LOW, 0, (MAS3_SW|MAS3_SR))@l 832 lis r4, CONFIG_SYS_CCSRBAR_PHYS_HIGH@h 833 ori r4, r4, CONFIG_SYS_CCSRBAR_PHYS_HIGH@l 834 mtspr MAS0, r0 835 mtspr MAS1, r1 836 mtspr MAS2, r2 837 mtspr MAS3, r3 838 mtspr MAS7, r4 839 isync 840 tlbwe 841 isync 842 msync 843 844 /* Map DCSR temporarily to physical address zero */ 845 li r0, 0 846 lis r3, DCSRBAR_LAWAR@h 847 ori r3, r3, DCSRBAR_LAWAR@l 848 849 stw r0, 0xc00(r7) /* LAWBARH0 */ 850 stw r0, 0xc04(r7) /* LAWBARL0 */ 851 sync 852 stw r3, 0xc08(r7) /* LAWAR0 */ 853 854 /* Read back from LAWAR to ensure the update is complete. */ 855 lwz r3, 0xc08(r7) /* LAWAR0 */ 856 isync 857 858 /* Create a TLB entry for DCSR at zero */ 859 860 addi r9, r8, 1 861 lis r0, MAS0_TLBSEL(1)@h 862 rlwimi r0, r9, 16, MAS0_ESEL_MSK 863 lis r1, FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M)@h 864 ori r1, r1, FSL_BOOKE_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M)@l 865 li r6, 0 /* DCSR effective address */ 866 ori r2, r6, MAS2_I|MAS2_G 867 li r3, MAS3_SW|MAS3_SR 868 li r4, 0 869 mtspr MAS0, r0 870 mtspr MAS1, r1 871 mtspr MAS2, r2 872 mtspr MAS3, r3 873 mtspr MAS7, r4 874 isync 875 tlbwe 876 isync 877 msync 878 879 /* enable the timebase */ 880#define CTBENR 0xe2084 881 li r3, 1 882 addis r4, r7, CTBENR@ha 883 stw r3, CTBENR@l(r4) 884 lwz r3, CTBENR@l(r4) 885 twi 0,r3,0 886 isync 887 888 .macro erratum_set_ccsr offset value 889 addis r3, r7, \offset@ha 890 lis r4, \value@h 891 addi r3, r3, \offset@l 892 ori r4, r4, \value@l 893 bl erratum_set_value 894 .endm 895 896 .macro erratum_set_dcsr offset value 897 addis r3, r6, \offset@ha 898 lis r4, \value@h 899 addi r3, r3, \offset@l 900 ori r4, r4, \value@l 901 bl erratum_set_value 902 .endm 903 904 erratum_set_dcsr 0xb0e08 0xe0201800 905 erratum_set_dcsr 0xb0e18 0xe0201800 906 erratum_set_dcsr 0xb0e38 0xe0400000 907 erratum_set_dcsr 0xb0008 0x00900000 908 erratum_set_dcsr 0xb0e40 0xe00a0000 909 erratum_set_ccsr 0x18600 CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY 910#ifdef CONFIG_RAMBOOT_PBL 911 erratum_set_ccsr 0x10f00 0x495e5000 912#else 913 erratum_set_ccsr 0x10f00 0x415e5000 914#endif 915 erratum_set_ccsr 0x11f00 0x415e5000 916 917 /* Make temp mapping uncacheable again, if it was initially */ 918 bl 2f 9192: mflr r3 920 tlbsx 0, r3 921 mfspr r4, MAS2 922 rlwimi r4, r15, 0, MAS2_I 923 rlwimi r4, r15, 0, MAS2_G 924 mtspr MAS2, r4 925 isync 926 tlbwe 927 isync 928 msync 929 930 /* Clear the cache */ 931 lis r3,(L1CSR1_ICFI|L1CSR1_ICLFR)@h 932 ori r3,r3,(L1CSR1_ICFI|L1CSR1_ICLFR)@l 933 sync 934 isync 935 mtspr SPRN_L1CSR1,r3 936 isync 9372: sync 938 mfspr r4,SPRN_L1CSR1 939 and. r4,r4,r3 940 bne 2b 941 942 lis r3,(L1CSR1_CPE|L1CSR1_ICE)@h 943 ori r3,r3,(L1CSR1_CPE|L1CSR1_ICE)@l 944 sync 945 isync 946 mtspr SPRN_L1CSR1,r3 947 isync 9482: sync 949 mfspr r4,SPRN_L1CSR1 950 and. r4,r4,r3 951 beq 2b 952 953 /* Remove temporary mappings */ 954 lis r0, MAS0_TLBSEL(1)@h 955 rlwimi r0, r9, 16, MAS0_ESEL_MSK 956 li r3, 0 957 mtspr MAS0, r0 958 mtspr MAS1, r3 959 isync 960 tlbwe 961 isync 962 msync 963 964 li r3, 0 965 stw r3, 0xc08(r7) /* LAWAR0 */ 966 lwz r3, 0xc08(r7) 967 isync 968 969 lis r0, MAS0_TLBSEL(1)@h 970 rlwimi r0, r8, 16, MAS0_ESEL_MSK 971 li r3, 0 972 mtspr MAS0, r0 973 mtspr MAS1, r3 974 isync 975 tlbwe 976 isync 977 msync 978 979 b 9f 980 981 /* r3 = addr, r4 = value, clobbers r5, r11, r12 */ 982erratum_set_value: 983 /* Lock two cache lines into I-Cache */ 984 sync 985 mfspr r11, SPRN_L1CSR1 986 rlwinm r11, r11, 0, ~L1CSR1_ICUL 987 sync 988 isync 989 mtspr SPRN_L1CSR1, r11 990 isync 991 992 mflr r12 993 bl 5f 9945: mflr r5 995 addi r5, r5, 2f - 5b 996 icbtls 0, 0, r5 997 addi r5, r5, 64 998 999 sync 1000 mfspr r11, SPRN_L1CSR1 10013: andi. r11, r11, L1CSR1_ICUL 1002 bne 3b 1003 1004 icbtls 0, 0, r5 1005 addi r5, r5, 64 1006 1007 sync 1008 mfspr r11, SPRN_L1CSR1 10093: andi. r11, r11, L1CSR1_ICUL 1010 bne 3b 1011 1012 b 2f 1013 .align 6 1014 /* Inside a locked cacheline, wait a while, write, then wait a while */ 10152: sync 1016 1017 mfspr r5, SPRN_TBRL 1018 addis r11, r5, 0x10000@h /* wait 65536 timebase ticks */ 10194: mfspr r5, SPRN_TBRL 1020 subf. r5, r5, r11 1021 bgt 4b 1022 1023 stw r4, 0(r3) 1024 1025 mfspr r5, SPRN_TBRL 1026 addis r11, r5, 0x10000@h /* wait 65536 timebase ticks */ 10274: mfspr r5, SPRN_TBRL 1028 subf. r5, r5, r11 1029 bgt 4b 1030 1031 sync 1032 1033 /* 1034 * Fill out the rest of this cache line and the next with nops, 1035 * to ensure that nothing outside the locked area will be 1036 * fetched due to a branch. 1037 */ 1038 .rept 19 1039 nop 1040 .endr 1041 1042 sync 1043 mfspr r11, SPRN_L1CSR1 1044 rlwinm r11, r11, 0, ~L1CSR1_ICUL 1045 sync 1046 isync 1047 mtspr SPRN_L1CSR1, r11 1048 isync 1049 1050 mtlr r12 1051 blr 1052 10539: 1054#endif 1055 1056create_init_ram_area: 1057 lis r6,FSL_BOOKE_MAS0(1, 15, 0)@h 1058 ori r6,r6,FSL_BOOKE_MAS0(1, 15, 0)@l 1059 1060#ifdef NOR_BOOT 1061 /* create a temp mapping in AS=1 to the 4M boot window */ 1062 create_tlb1_entry 15, \ 1063 1, BOOKE_PAGESZ_4M, \ 1064 CONFIG_SYS_MONITOR_BASE & 0xffc00000, MAS2_I|MAS2_G, \ 1065 0xffc00000, MAS3_SX|MAS3_SW|MAS3_SR, \ 1066 0, r6 1067 1068#elif !defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SECURE_BOOT) 1069 /* create a temp mapping in AS = 1 for Flash mapping 1070 * created by PBL for ISBC code 1071 */ 1072 create_tlb1_entry 15, \ 1073 1, BOOKE_PAGESZ_1M, \ 1074 CONFIG_SYS_MONITOR_BASE & 0xfff00000, MAS2_I|MAS2_G, \ 1075 CONFIG_SYS_PBI_FLASH_WINDOW & 0xfff00000, MAS3_SX|MAS3_SW|MAS3_SR, \ 1076 0, r6 1077 1078/* 1079 * For Targets without CONFIG_SPL like P3, P5 1080 * and for targets with CONFIG_SPL like T1, T2, T4, only for 1081 * u-boot-spl i.e. CONFIG_SPL_BUILD 1082 */ 1083#elif defined(CONFIG_RAMBOOT_PBL) && defined(CONFIG_SECURE_BOOT) && \ 1084 (!defined(CONFIG_SPL) || defined(CONFIG_SPL_BUILD)) 1085 /* create a temp mapping in AS = 1 for mapping CONFIG_SYS_MONITOR_BASE 1086 * to L3 Address configured by PBL for ISBC code 1087 */ 1088 create_tlb1_entry 15, \ 1089 1, BOOKE_PAGESZ_1M, \ 1090 CONFIG_SYS_MONITOR_BASE & 0xfff00000, MAS2_I|MAS2_G, \ 1091 CONFIG_SYS_INIT_L3_ADDR & 0xfff00000, MAS3_SX|MAS3_SW|MAS3_SR, \ 1092 0, r6 1093 1094#else 1095 /* 1096 * create a temp mapping in AS=1 to the 1M CONFIG_SYS_MONITOR_BASE space, the main 1097 * image has been relocated to CONFIG_SYS_MONITOR_BASE on the second stage. 1098 */ 1099 create_tlb1_entry 15, \ 1100 1, BOOKE_PAGESZ_1M, \ 1101 CONFIG_SYS_MONITOR_BASE & 0xfff00000, MAS2_I|MAS2_G, \ 1102 CONFIG_SYS_MONITOR_BASE & 0xfff00000, MAS3_SX|MAS3_SW|MAS3_SR, \ 1103 0, r6 1104#endif 1105 1106 /* create a temp mapping in AS=1 to the stack */ 1107#if defined(CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) && \ 1108 defined(CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH) 1109 create_tlb1_entry 14, \ 1110 1, BOOKE_PAGESZ_16K, \ 1111 CONFIG_SYS_INIT_RAM_ADDR, 0, \ 1112 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW, MAS3_SX|MAS3_SW|MAS3_SR, \ 1113 CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH, r6 1114 1115#else 1116 create_tlb1_entry 14, \ 1117 1, BOOKE_PAGESZ_16K, \ 1118 CONFIG_SYS_INIT_RAM_ADDR, 0, \ 1119 CONFIG_SYS_INIT_RAM_ADDR, MAS3_SX|MAS3_SW|MAS3_SR, \ 1120 0, r6 1121#endif 1122 1123 lis r6,MSR_IS|MSR_DS|MSR_DE@h 1124 ori r6,r6,MSR_IS|MSR_DS|MSR_DE@l 1125 lis r7,switch_as@h 1126 ori r7,r7,switch_as@l 1127 1128 mtspr SPRN_SRR0,r7 1129 mtspr SPRN_SRR1,r6 1130 rfi 1131 1132switch_as: 1133/* L1 DCache is used for initial RAM */ 1134 1135 /* Allocate Initial RAM in data cache. 1136 */ 1137 lis r3,CONFIG_SYS_INIT_RAM_ADDR@h 1138 ori r3,r3,CONFIG_SYS_INIT_RAM_ADDR@l 1139 mfspr r2, L1CFG0 1140 andi. r2, r2, 0x1ff 1141 /* cache size * 1024 / (2 * L1 line size) */ 1142 slwi r2, r2, (10 - 1 - L1_CACHE_SHIFT) 1143 mtctr r2 1144 li r0,0 11451: 1146 dcbz r0,r3 1147#ifdef CONFIG_E6500 /* Lock/unlock L2 cache long with L1 */ 1148 dcbtls 2, r0, r3 1149 dcbtls 0, r0, r3 1150#else 1151 dcbtls 0, r0, r3 1152#endif 1153 addi r3,r3,CONFIG_SYS_CACHELINE_SIZE 1154 bdnz 1b 1155 1156 /* Jump out the last 4K page and continue to 'normal' start */ 1157#if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_SPL) 1158 /* We assume that we're already running at the address we're linked at */ 1159 b _start_cont 1160#else 1161 /* Calculate absolute address in FLASH and jump there */ 1162 /*--------------------------------------------------------------*/ 1163 lis r3,CONFIG_SYS_MONITOR_BASE@h 1164 ori r3,r3,CONFIG_SYS_MONITOR_BASE@l 1165 addi r3,r3,_start_cont - _start 1166 mtlr r3 1167 blr 1168#endif 1169 1170 .text 1171 .globl _start 1172_start: 1173 .long 0x27051956 /* U-BOOT Magic Number */ 1174 .globl version_string 1175version_string: 1176 .ascii U_BOOT_VERSION_STRING, "\0" 1177 1178 .align 4 1179 .globl _start_cont 1180_start_cont: 1181 /* Setup the stack in initial RAM,could be L2-as-SRAM or L1 dcache*/ 1182 lis r3,(CONFIG_SYS_INIT_RAM_ADDR)@h 1183 ori r3,r3,((CONFIG_SYS_INIT_SP_OFFSET-16)&~0xf)@l /* Align to 16 */ 1184 1185#if CONFIG_VAL(SYS_MALLOC_F_LEN) 1186#if CONFIG_VAL(SYS_MALLOC_F_LEN) + GENERATED_GBL_DATA_SIZE > CONFIG_SYS_INIT_RAM_SIZE 1187#error "SYS_MALLOC_F_LEN too large to fit into initial RAM." 1188#endif 1189 1190 /* Leave 16+ byte for back chain termination and NULL return address */ 1191 subi r3,r3,((CONFIG_VAL(SYS_MALLOC_F_LEN)+16+15)&~0xf) 1192#endif 1193 1194 /* End of RAM */ 1195 lis r4,(CONFIG_SYS_INIT_RAM_ADDR)@h 1196 ori r4,r4,(CONFIG_SYS_INIT_RAM_SIZE)@l 1197 1198 li r0,0 1199 12001: subi r4,r4,4 1201 stw r0,0(r4) 1202 cmplw r4,r3 1203 bne 1b 1204 1205#if CONFIG_VAL(SYS_MALLOC_F_LEN) 1206 lis r4,(CONFIG_SYS_INIT_RAM_ADDR)@h 1207 ori r4,r4,(CONFIG_SYS_GBL_DATA_OFFSET)@l 1208 1209 addi r3,r3,16 /* Pre-relocation malloc area */ 1210 stw r3,GD_MALLOC_BASE(r4) 1211 subi r3,r3,16 1212#endif 1213 li r0,0 1214 stw r0,0(r3) /* Terminate Back Chain */ 1215 stw r0,+4(r3) /* NULL return address. */ 1216 mr r1,r3 /* Transfer to SP(r1) */ 1217 1218 GET_GOT 1219 1220 /* Pass our potential ePAPR device tree pointer to cpu_init_early_f */ 1221 mr r3, r24 1222 1223 bl cpu_init_early_f 1224 1225 /* switch back to AS = 0 */ 1226 lis r3,(MSR_CE|MSR_ME|MSR_DE)@h 1227 ori r3,r3,(MSR_CE|MSR_ME|MSR_DE)@l 1228 mtmsr r3 1229 isync 1230 1231 bl cpu_init_f /* return boot_flag for calling board_init_f */ 1232 bl board_init_f 1233 isync 1234 1235 /* NOTREACHED - board_init_f() does not return */ 1236 1237#ifndef MINIMAL_SPL 1238 .globl _start_of_vectors 1239_start_of_vectors: 1240 1241/* Critical input. */ 1242 CRIT_EXCEPTION(0x0100, CriticalInput, CritcalInputException) 1243 1244/* Machine check */ 1245 MCK_EXCEPTION(0x200, MachineCheck, MachineCheckException) 1246 1247/* Data Storage exception. */ 1248 STD_EXCEPTION(0x0300, DataStorage, UnknownException) 1249 1250/* Instruction Storage exception. */ 1251 STD_EXCEPTION(0x0400, InstStorage, UnknownException) 1252 1253/* External Interrupt exception. */ 1254 STD_EXCEPTION(0x0500, ExtInterrupt, ExtIntException) 1255 1256/* Alignment exception. */ 1257Alignment: 1258 EXCEPTION_PROLOG(SRR0, SRR1) 1259 mfspr r4,DAR 1260 stw r4,_DAR(r21) 1261 mfspr r5,DSISR 1262 stw r5,_DSISR(r21) 1263 addi r3,r1,STACK_FRAME_OVERHEAD 1264 EXC_XFER_TEMPLATE(0x600, Alignment, AlignmentException, 1265 MSR_KERNEL, COPY_EE) 1266 1267/* Program check exception */ 1268ProgramCheck: 1269 EXCEPTION_PROLOG(SRR0, SRR1) 1270 addi r3,r1,STACK_FRAME_OVERHEAD 1271 EXC_XFER_TEMPLATE(0x700, ProgramCheck, ProgramCheckException, 1272 MSR_KERNEL, COPY_EE) 1273 1274 /* No FPU on MPC85xx. This exception is not supposed to happen. 1275 */ 1276 STD_EXCEPTION(0x0800, FPUnavailable, UnknownException) 1277 STD_EXCEPTION(0x0900, SystemCall, UnknownException) 1278 STD_EXCEPTION(0x0a00, Decrementer, timer_interrupt) 1279 STD_EXCEPTION(0x0b00, IntervalTimer, UnknownException) 1280 STD_EXCEPTION(0x0c00, WatchdogTimer, UnknownException) 1281 1282 STD_EXCEPTION(0x0d00, DataTLBError, UnknownException) 1283 STD_EXCEPTION(0x0e00, InstructionTLBError, UnknownException) 1284 1285 CRIT_EXCEPTION(0x0f00, DebugBreakpoint, DebugException ) 1286 1287 .globl _end_of_vectors 1288_end_of_vectors: 1289 1290 1291 . = . + (0x100 - ( . & 0xff )) /* align for debug */ 1292 1293/* 1294 * This code finishes saving the registers to the exception frame 1295 * and jumps to the appropriate handler for the exception. 1296 * Register r21 is pointer into trap frame, r1 has new stack pointer. 1297 * r23 is the address of the handler. 1298 */ 1299 .globl transfer_to_handler 1300transfer_to_handler: 1301 SAVE_GPR(7, r21) 1302 SAVE_4GPRS(8, r21) 1303 SAVE_8GPRS(12, r21) 1304 SAVE_8GPRS(24, r21) 1305 1306 li r22,0 1307 stw r22,RESULT(r21) 1308 mtspr SPRG2,r22 /* r1 is now kernel sp */ 1309 1310 mtctr r23 /* virtual address of handler */ 1311 mtmsr r20 1312 bctrl 1313 1314int_return: 1315 mfmsr r28 /* Disable interrupts */ 1316 li r4,0 1317 ori r4,r4,MSR_EE 1318 andc r28,r28,r4 1319 SYNC /* Some chip revs need this... */ 1320 mtmsr r28 1321 SYNC 1322 lwz r2,_CTR(r1) 1323 lwz r0,_LINK(r1) 1324 mtctr r2 1325 mtlr r0 1326 lwz r2,_XER(r1) 1327 lwz r0,_CCR(r1) 1328 mtspr XER,r2 1329 mtcrf 0xFF,r0 1330 REST_10GPRS(3, r1) 1331 REST_10GPRS(13, r1) 1332 REST_8GPRS(23, r1) 1333 REST_GPR(31, r1) 1334 lwz r2,_NIP(r1) /* Restore environment */ 1335 lwz r0,_MSR(r1) 1336 mtspr SRR0,r2 1337 mtspr SRR1,r0 1338 lwz r0,GPR0(r1) 1339 lwz r2,GPR2(r1) 1340 lwz r1,GPR1(r1) 1341 SYNC 1342 rfi 1343 1344/* Cache functions. 1345*/ 1346.globl flush_icache 1347flush_icache: 1348.globl invalidate_icache 1349invalidate_icache: 1350 mfspr r0,L1CSR1 1351 ori r0,r0,L1CSR1_ICFI 1352 msync 1353 isync 1354 mtspr L1CSR1,r0 1355 isync 1356 blr /* entire I cache */ 1357 1358.globl invalidate_dcache 1359invalidate_dcache: 1360 mfspr r0,L1CSR0 1361 ori r0,r0,L1CSR0_DCFI 1362 msync 1363 isync 1364 mtspr L1CSR0,r0 1365 isync 1366 blr 1367 1368 .globl icache_enable 1369icache_enable: 1370 mflr r8 1371 bl invalidate_icache 1372 mtlr r8 1373 isync 1374 mfspr r4,L1CSR1 1375 ori r4,r4,(L1CSR1_CPE | L1CSR1_ICE)@l 1376 oris r4,r4,(L1CSR1_CPE | L1CSR1_ICE)@h 1377 mtspr L1CSR1,r4 1378 isync 1379 blr 1380 1381 .globl icache_disable 1382icache_disable: 1383 mfspr r0,L1CSR1 1384 lis r3,0 1385 ori r3,r3,L1CSR1_ICE 1386 andc r0,r0,r3 1387 mtspr L1CSR1,r0 1388 isync 1389 blr 1390 1391 .globl icache_status 1392icache_status: 1393 mfspr r3,L1CSR1 1394 andi. r3,r3,L1CSR1_ICE 1395 blr 1396 1397 .globl dcache_enable 1398dcache_enable: 1399 mflr r8 1400 bl invalidate_dcache 1401 mtlr r8 1402 isync 1403 mfspr r0,L1CSR0 1404 ori r0,r0,(L1CSR0_CPE | L1CSR0_DCE)@l 1405 oris r0,r0,(L1CSR0_CPE | L1CSR0_DCE)@h 1406 msync 1407 isync 1408 mtspr L1CSR0,r0 1409 isync 1410 blr 1411 1412 .globl dcache_disable 1413dcache_disable: 1414 mfspr r3,L1CSR0 1415 lis r4,0 1416 ori r4,r4,L1CSR0_DCE 1417 andc r3,r3,r4 1418 mtspr L1CSR0,r3 1419 isync 1420 blr 1421 1422 .globl dcache_status 1423dcache_status: 1424 mfspr r3,L1CSR0 1425 andi. r3,r3,L1CSR0_DCE 1426 blr 1427 1428/*------------------------------------------------------------------------------- */ 1429/* Function: in8 */ 1430/* Description: Input 8 bits */ 1431/*------------------------------------------------------------------------------- */ 1432 .globl in8 1433in8: 1434 lbz r3,0x0000(r3) 1435 blr 1436 1437/*------------------------------------------------------------------------------- */ 1438/* Function: out8 */ 1439/* Description: Output 8 bits */ 1440/*------------------------------------------------------------------------------- */ 1441 .globl out8 1442out8: 1443 stb r4,0x0000(r3) 1444 sync 1445 blr 1446 1447/*------------------------------------------------------------------------------- */ 1448/* Function: out16 */ 1449/* Description: Output 16 bits */ 1450/*------------------------------------------------------------------------------- */ 1451 .globl out16 1452out16: 1453 sth r4,0x0000(r3) 1454 sync 1455 blr 1456 1457/*------------------------------------------------------------------------------- */ 1458/* Function: out16r */ 1459/* Description: Byte reverse and output 16 bits */ 1460/*------------------------------------------------------------------------------- */ 1461 .globl out16r 1462out16r: 1463 sthbrx r4,r0,r3 1464 sync 1465 blr 1466 1467/*------------------------------------------------------------------------------- */ 1468/* Function: out32 */ 1469/* Description: Output 32 bits */ 1470/*------------------------------------------------------------------------------- */ 1471 .globl out32 1472out32: 1473 stw r4,0x0000(r3) 1474 sync 1475 blr 1476 1477/*------------------------------------------------------------------------------- */ 1478/* Function: out32r */ 1479/* Description: Byte reverse and output 32 bits */ 1480/*------------------------------------------------------------------------------- */ 1481 .globl out32r 1482out32r: 1483 stwbrx r4,r0,r3 1484 sync 1485 blr 1486 1487/*------------------------------------------------------------------------------- */ 1488/* Function: in16 */ 1489/* Description: Input 16 bits */ 1490/*------------------------------------------------------------------------------- */ 1491 .globl in16 1492in16: 1493 lhz r3,0x0000(r3) 1494 blr 1495 1496/*------------------------------------------------------------------------------- */ 1497/* Function: in16r */ 1498/* Description: Input 16 bits and byte reverse */ 1499/*------------------------------------------------------------------------------- */ 1500 .globl in16r 1501in16r: 1502 lhbrx r3,r0,r3 1503 blr 1504 1505/*------------------------------------------------------------------------------- */ 1506/* Function: in32 */ 1507/* Description: Input 32 bits */ 1508/*------------------------------------------------------------------------------- */ 1509 .globl in32 1510in32: 1511 lwz 3,0x0000(3) 1512 blr 1513 1514/*------------------------------------------------------------------------------- */ 1515/* Function: in32r */ 1516/* Description: Input 32 bits and byte reverse */ 1517/*------------------------------------------------------------------------------- */ 1518 .globl in32r 1519in32r: 1520 lwbrx r3,r0,r3 1521 blr 1522#endif /* !MINIMAL_SPL */ 1523 1524/*------------------------------------------------------------------------------*/ 1525 1526/* 1527 * void write_tlb(mas0, mas1, mas2, mas3, mas7) 1528 */ 1529 .globl write_tlb 1530write_tlb: 1531 mtspr MAS0,r3 1532 mtspr MAS1,r4 1533 mtspr MAS2,r5 1534 mtspr MAS3,r6 1535#ifdef CONFIG_ENABLE_36BIT_PHYS 1536 mtspr MAS7,r7 1537#endif 1538 li r3,0 1539#ifdef CONFIG_SYS_BOOK3E_HV 1540 mtspr MAS8,r3 1541#endif 1542 isync 1543 tlbwe 1544 msync 1545 isync 1546 blr 1547 1548/* 1549 * void relocate_code (addr_sp, gd, addr_moni) 1550 * 1551 * This "function" does not return, instead it continues in RAM 1552 * after relocating the monitor code. 1553 * 1554 * r3 = dest 1555 * r4 = src 1556 * r5 = length in bytes 1557 * r6 = cachelinesize 1558 */ 1559 .globl relocate_code 1560relocate_code: 1561 mr r1,r3 /* Set new stack pointer */ 1562 mr r9,r4 /* Save copy of Init Data pointer */ 1563 mr r10,r5 /* Save copy of Destination Address */ 1564 1565 GET_GOT 1566#ifndef CONFIG_SPL_SKIP_RELOCATE 1567 mr r3,r5 /* Destination Address */ 1568 lis r4,CONFIG_SYS_MONITOR_BASE@h /* Source Address */ 1569 ori r4,r4,CONFIG_SYS_MONITOR_BASE@l 1570 lwz r5,GOT(__init_end) 1571 sub r5,r5,r4 1572 li r6,CONFIG_SYS_CACHELINE_SIZE /* Cache Line Size */ 1573 1574 /* 1575 * Fix GOT pointer: 1576 * 1577 * New GOT-PTR = (old GOT-PTR - CONFIG_SYS_MONITOR_BASE) + Destination Address 1578 * 1579 * Offset: 1580 */ 1581 sub r15,r10,r4 1582 1583 /* First our own GOT */ 1584 add r12,r12,r15 1585 /* the the one used by the C code */ 1586 add r30,r30,r15 1587 1588 /* 1589 * Now relocate code 1590 */ 1591 1592 cmplw cr1,r3,r4 1593 addi r0,r5,3 1594 srwi. r0,r0,2 1595 beq cr1,4f /* In place copy is not necessary */ 1596 beq 7f /* Protect against 0 count */ 1597 mtctr r0 1598 bge cr1,2f 1599 1600 la r8,-4(r4) 1601 la r7,-4(r3) 16021: lwzu r0,4(r8) 1603 stwu r0,4(r7) 1604 bdnz 1b 1605 b 4f 1606 16072: slwi r0,r0,2 1608 add r8,r4,r0 1609 add r7,r3,r0 16103: lwzu r0,-4(r8) 1611 stwu r0,-4(r7) 1612 bdnz 3b 1613 1614/* 1615 * Now flush the cache: note that we must start from a cache aligned 1616 * address. Otherwise we might miss one cache line. 1617 */ 16184: cmpwi r6,0 1619 add r5,r3,r5 1620 beq 7f /* Always flush prefetch queue in any case */ 1621 subi r0,r6,1 1622 andc r3,r3,r0 1623 mr r4,r3 16245: dcbst 0,r4 1625 add r4,r4,r6 1626 cmplw r4,r5 1627 blt 5b 1628 sync /* Wait for all dcbst to complete on bus */ 1629 mr r4,r3 16306: icbi 0,r4 1631 add r4,r4,r6 1632 cmplw r4,r5 1633 blt 6b 16347: sync /* Wait for all icbi to complete on bus */ 1635 isync 1636 1637/* 1638 * We are done. Do not return, instead branch to second part of board 1639 * initialization, now running from RAM. 1640 */ 1641 1642 addi r0,r10,in_ram - _start 1643 1644 /* 1645 * As IVPR is going to point RAM address, 1646 * Make sure IVOR15 has valid opcode to support debugger 1647 */ 1648 mtspr IVOR15,r0 1649 1650 /* 1651 * Re-point the IVPR at RAM 1652 */ 1653 mtspr IVPR,r10 1654 1655 mtlr r0 1656 blr /* NEVER RETURNS! */ 1657#endif 1658 .globl in_ram 1659in_ram: 1660 1661 /* 1662 * Relocation Function, r12 point to got2+0x8000 1663 * 1664 * Adjust got2 pointers, no need to check for 0, this code 1665 * already puts a few entries in the table. 1666 */ 1667 li r0,__got2_entries@sectoff@l 1668 la r3,GOT(_GOT2_TABLE_) 1669 lwz r11,GOT(_GOT2_TABLE_) 1670 mtctr r0 1671 sub r11,r3,r11 1672 addi r3,r3,-4 16731: lwzu r0,4(r3) 1674 cmpwi r0,0 1675 beq- 2f 1676 add r0,r0,r11 1677 stw r0,0(r3) 16782: bdnz 1b 1679 1680 /* 1681 * Now adjust the fixups and the pointers to the fixups 1682 * in case we need to move ourselves again. 1683 */ 1684 li r0,__fixup_entries@sectoff@l 1685 lwz r3,GOT(_FIXUP_TABLE_) 1686 cmpwi r0,0 1687 mtctr r0 1688 addi r3,r3,-4 1689 beq 4f 16903: lwzu r4,4(r3) 1691 lwzux r0,r4,r11 1692 cmpwi r0,0 1693 add r0,r0,r11 1694 stw r4,0(r3) 1695 beq- 5f 1696 stw r0,0(r4) 16975: bdnz 3b 16984: 1699clear_bss: 1700 /* 1701 * Now clear BSS segment 1702 */ 1703 lwz r3,GOT(__bss_start) 1704 lwz r4,GOT(__bss_end) 1705 1706 cmplw 0,r3,r4 1707 beq 6f 1708 1709 li r0,0 17105: 1711 stw r0,0(r3) 1712 addi r3,r3,4 1713 cmplw 0,r3,r4 1714 blt 5b 17156: 1716 1717 mr r3,r9 /* Init Data pointer */ 1718 mr r4,r10 /* Destination Address */ 1719 bl board_init_r 1720 1721#ifndef MINIMAL_SPL 1722 /* 1723 * Copy exception vector code to low memory 1724 * 1725 * r3: dest_addr 1726 * r7: source address, r8: end address, r9: target address 1727 */ 1728 .globl trap_init 1729trap_init: 1730 mflr r11 1731 bl _GLOBAL_OFFSET_TABLE_-4 1732 mflr r12 1733 1734 /* Update IVORs as per relocation */ 1735 mtspr IVPR,r3 1736 1737 lwz r4,CriticalInput@got(r12) 1738 mtspr IVOR0,r4 /* 0: Critical input */ 1739 lwz r4,MachineCheck@got(r12) 1740 mtspr IVOR1,r4 /* 1: Machine check */ 1741 lwz r4,DataStorage@got(r12) 1742 mtspr IVOR2,r4 /* 2: Data storage */ 1743 lwz r4,InstStorage@got(r12) 1744 mtspr IVOR3,r4 /* 3: Instruction storage */ 1745 lwz r4,ExtInterrupt@got(r12) 1746 mtspr IVOR4,r4 /* 4: External interrupt */ 1747 lwz r4,Alignment@got(r12) 1748 mtspr IVOR5,r4 /* 5: Alignment */ 1749 lwz r4,ProgramCheck@got(r12) 1750 mtspr IVOR6,r4 /* 6: Program check */ 1751 lwz r4,FPUnavailable@got(r12) 1752 mtspr IVOR7,r4 /* 7: floating point unavailable */ 1753 lwz r4,SystemCall@got(r12) 1754 mtspr IVOR8,r4 /* 8: System call */ 1755 /* 9: Auxiliary processor unavailable(unsupported) */ 1756 lwz r4,Decrementer@got(r12) 1757 mtspr IVOR10,r4 /* 10: Decrementer */ 1758 lwz r4,IntervalTimer@got(r12) 1759 mtspr IVOR11,r4 /* 11: Interval timer */ 1760 lwz r4,WatchdogTimer@got(r12) 1761 mtspr IVOR12,r4 /* 12: Watchdog timer */ 1762 lwz r4,DataTLBError@got(r12) 1763 mtspr IVOR13,r4 /* 13: Data TLB error */ 1764 lwz r4,InstructionTLBError@got(r12) 1765 mtspr IVOR14,r4 /* 14: Instruction TLB error */ 1766 lwz r4,DebugBreakpoint@got(r12) 1767 mtspr IVOR15,r4 /* 15: Debug */ 1768 1769 mtlr r11 1770 blr 1771 1772.globl unlock_ram_in_cache 1773unlock_ram_in_cache: 1774 /* invalidate the INIT_RAM section */ 1775 lis r3,(CONFIG_SYS_INIT_RAM_ADDR & ~(CONFIG_SYS_CACHELINE_SIZE-1))@h 1776 ori r3,r3,(CONFIG_SYS_INIT_RAM_ADDR & ~(CONFIG_SYS_CACHELINE_SIZE-1))@l 1777 mfspr r4,L1CFG0 1778 andi. r4,r4,0x1ff 1779 slwi r4,r4,(10 - 1 - L1_CACHE_SHIFT) 1780 mtctr r4 17811: dcbi r0,r3 1782#ifdef CONFIG_E6500 /* lock/unlock L2 cache long with L1 */ 1783 dcblc 2, r0, r3 1784 dcblc 0, r0, r3 1785#else 1786 dcblc r0,r3 1787#endif 1788 addi r3,r3,CONFIG_SYS_CACHELINE_SIZE 1789 bdnz 1b 1790 sync 1791 1792 /* Invalidate the TLB entries for the cache */ 1793 lis r3,CONFIG_SYS_INIT_RAM_ADDR@h 1794 ori r3,r3,CONFIG_SYS_INIT_RAM_ADDR@l 1795 tlbivax 0,r3 1796 addi r3,r3,0x1000 1797 tlbivax 0,r3 1798 addi r3,r3,0x1000 1799 tlbivax 0,r3 1800 addi r3,r3,0x1000 1801 tlbivax 0,r3 1802 isync 1803 blr 1804 1805.globl flush_dcache 1806flush_dcache: 1807 mfspr r3,SPRN_L1CFG0 1808 1809 rlwinm r5,r3,9,3 /* Extract cache block size */ 1810 twlgti r5,1 /* Only 32 and 64 byte cache blocks 1811 * are currently defined. 1812 */ 1813 li r4,32 1814 subfic r6,r5,2 /* r6 = log2(1KiB / cache block size) - 1815 * log2(number of ways) 1816 */ 1817 slw r5,r4,r5 /* r5 = cache block size */ 1818 1819 rlwinm r7,r3,0,0xff /* Extract number of KiB in the cache */ 1820 mulli r7,r7,13 /* An 8-way cache will require 13 1821 * loads per set. 1822 */ 1823 slw r7,r7,r6 1824 1825 /* save off HID0 and set DCFA */ 1826 mfspr r8,SPRN_HID0 1827 ori r9,r8,HID0_DCFA@l 1828 mtspr SPRN_HID0,r9 1829 isync 1830 1831 lis r4,0 1832 mtctr r7 1833 18341: lwz r3,0(r4) /* Load... */ 1835 add r4,r4,r5 1836 bdnz 1b 1837 1838 msync 1839 lis r4,0 1840 mtctr r7 1841 18421: dcbf 0,r4 /* ...and flush. */ 1843 add r4,r4,r5 1844 bdnz 1b 1845 1846 /* restore HID0 */ 1847 mtspr SPRN_HID0,r8 1848 isync 1849 1850 blr 1851#endif /* !MINIMAL_SPL */ 1852