xref: /openbmc/u-boot/arch/m68k/cpu/mcf5445x/start.S (revision 729c2db7) 
1/*
2 * Copyright (C) 2003	Josef Baumgartner <josef.baumgartner@telex.de>
3 * Based on code from Bernhard Kuhn <bkuhn@metrowerks.com>
4 *
5 * Copyright 2010-2012 Freescale Semiconductor, Inc.
6 * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
7 *
8 * SPDX-License-Identifier:	GPL-2.0+
9 */
10
11#include <common.h>
12#include <asm-offsets.h>
13#include <config.h>
14#include <timestamp.h>
15#include "version.h"
16#include <asm/cache.h>
17
18#ifndef	 CONFIG_IDENT_STRING
19#define	 CONFIG_IDENT_STRING ""
20#endif
21
22#define _START	_start
23#define _FAULT	_fault
24
25#define SAVE_ALL						\
26	move.w	#0x2700,%sr;		/* disable intrs */	\
27	subl	#60,%sp;		/* space for 15 regs */ \
28	moveml	%d0-%d7/%a0-%a6,%sp@;
29
30#define RESTORE_ALL						\
31	moveml	%sp@,%d0-%d7/%a0-%a6;				\
32	addl	#60,%sp;		/* space for 15 regs */ \
33	rte;
34
35#if defined(CONFIG_SERIAL_BOOT)
36#define ASM_DRAMINIT	(asm_dram_init - CONFIG_SYS_TEXT_BASE + \
37	CONFIG_SYS_INIT_RAM_ADDR)
38#define ASM_DRAMINIT_N	(asm_dram_init - CONFIG_SYS_TEXT_BASE)
39#define ASM_SBF_IMG_HDR	(asm_sbf_img_hdr - CONFIG_SYS_TEXT_BASE + \
40	CONFIG_SYS_INIT_RAM_ADDR)
41#endif
42
43.text
44
45/*
46 * Vector table. This is used for initial platform startup.
47 * These vectors are to catch any un-intended traps.
48 */
49_vectors:
50#if defined(CONFIG_SERIAL_BOOT)
51
52INITSP:	.long	0			/* Initial SP	*/
53#ifdef CONFIG_CF_SBF
54INITPC:	.long	ASM_DRAMINIT		/* Initial PC 	*/
55#endif
56#ifdef CONFIG_SYS_NAND_BOOT
57INITPC:	.long	ASM_DRAMINIT_N		/* Initial PC 	*/
58#endif
59
60#else
61
62INITSP:	.long	0			/* Initial SP	*/
63INITPC:	.long	_START			/* Initial PC 	*/
64
65#endif
66
67vector02_0F:
68.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
69.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
70
71/* Reserved */
72vector10_17:
73.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
74
75vector18_1F:
76.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
77
78#if !defined(CONFIG_SERIAL_BOOT)
79
80/* TRAP #0 - #15 */
81vector20_2F:
82.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
83.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
84
85/* Reserved	*/
86vector30_3F:
87.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
88.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
89
90vector64_127:
91.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
92.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
93.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
94.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
95.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
96.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
97.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
98.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
99
100vector128_191:
101.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
102.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
103.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
104.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
105.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
106.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
107.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
108.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
109
110vector192_255:
111.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
112.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
113.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
114.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
115.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
116.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
117.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
118.long	_FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT, _FAULT
119#endif
120
121#if defined(CONFIG_SERIAL_BOOT)
122	/* Image header: chksum 4 bytes, len 4 bytes, img dest 4 bytes */
123asm_sbf_img_hdr:
124	.long	0x00000000		/* checksum, not yet implemented */
125	.long	0x00040000		/* image length */
126	.long	CONFIG_SYS_TEXT_BASE	/* image to be relocated at */
127
128asm_dram_init:
129	move.w	#0x2700,%sr		/* Mask off Interrupt */
130
131#ifdef CONFIG_SYS_NAND_BOOT
132	/* for assembly stack */
133	move.l	#(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_CTRL), %d0
134	movec	%d0, %RAMBAR1
135
136	move.l	#(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET), %sp
137	clr.l	%sp@-
138#endif
139
140#ifdef CONFIG_CF_SBF
141	move.l	#CONFIG_SYS_INIT_RAM_ADDR, %d0
142	movec	%d0, %VBR
143
144	move.l	#(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_CTRL), %d0
145	movec	%d0, %RAMBAR1
146
147	/* initialize general use internal ram */
148	move.l	#0, %d0
149	move.l	#(ICACHE_STATUS), %a1	/* icache */
150	move.l	#(DCACHE_STATUS), %a2	/* dcache */
151	move.l	%d0, (%a1)
152	move.l	%d0, (%a2)
153
154	/* invalidate and disable cache */
155	move.l	#(CONFIG_SYS_ICACHE_INV + CONFIG_SYS_DCACHE_INV), %d0
156	movec	%d0, %CACR		/* Invalidate cache */
157	move.l	#0, %d0
158	movec	%d0, %ACR0
159	movec	%d0, %ACR1
160	movec	%d0, %ACR2
161	movec	%d0, %ACR3
162
163	move.l	#(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET), %sp
164	clr.l	%sp@-
165
166	/* Must disable global address */
167	move.l	#0xFC008000, %a1
168	move.l	#(CONFIG_SYS_CS0_BASE), (%a1)
169	move.l	#0xFC008008, %a1
170	move.l	#(CONFIG_SYS_CS0_CTRL), (%a1)
171	move.l	#0xFC008004, %a1
172	move.l	#(CONFIG_SYS_CS0_MASK), (%a1)
173#endif /* CONFIG_CF_SBF */
174
175#ifdef CONFIG_MCF5441x
176	/* TC: enable all peripherals,
177	in the future only enable certain peripherals */
178	move.l	#0xFC04002D, %a1
179
180#if defined(CONFIG_CF_SBF)
181	move.b	#23, (%a1)		/* dspi */
182#endif
183	move.b	#46, (%a1)		/* DDR */
184
185	/* slew settings */
186	move.l	#0xEC094060, %a1
187	move.b	#0, (%a1)
188
189	/* use vco instead of cpu*2 clock for ddr clock */
190	move.l	#0xEC09001A, %a1
191	move.w	#0xE01D, (%a1)
192
193	/* DDR settings */
194	move.l	#0xFC0B8180, %a1
195	move.l	#0x00000000, (%a1)
196	move.l	#0x40000000, (%a1)
197
198	move.l	#0xFC0B81AC, %a1
199	move.l	#0x01030203, (%a1)
200
201	move.l	#0xFC0B8000, %a1
202	move.l	#0x01010101, (%a1)+	/* 0x00 */
203	move.l	#0x00000101, (%a1)+	/* 0x04 */
204	move.l	#0x01010100, (%a1)+	/* 0x08 */
205	move.l	#0x01010000, (%a1)+	/* 0x0C */
206	move.l	#0x00010101, (%a1)+	/* 0x10 */
207	move.l	#0xFC0B8018, %a1
208	move.l	#0x00010100, (%a1)+	/* 0x18 */
209	move.l	#0x00000001, (%a1)+	/* 0x1C */
210	move.l	#0x01000001, (%a1)+	/* 0x20 */
211	move.l	#0x00000100, (%a1)+	/* 0x24 */
212	move.l	#0x00010001, (%a1)+	/* 0x28 */
213	move.l	#0x00000200, (%a1)+	/* 0x2C */
214	move.l	#0x01000002, (%a1)+	/* 0x30 */
215	move.l	#0x00000000, (%a1)+	/* 0x34 */
216	move.l	#0x00000100, (%a1)+	/* 0x38 */
217	move.l	#0x02000100, (%a1)+	/* 0x3C */
218	move.l	#0x02000407, (%a1)+	/* 0x40 */
219	move.l	#0x02030007, (%a1)+	/* 0x44 */
220	move.l	#0x02000100, (%a1)+	/* 0x48 */
221	move.l	#0x0A030203, (%a1)+	/* 0x4C */
222	move.l	#0x00020708, (%a1)+	/* 0x50 */
223	move.l	#0x00050008, (%a1)+	/* 0x54 */
224	move.l	#0x04030002, (%a1)+	/* 0x58 */
225	move.l	#0x00000004, (%a1)+	/* 0x5C */
226	move.l	#0x020A0000, (%a1)+	/* 0x60 */
227	move.l	#0x0C00000E, (%a1)+	/* 0x64 */
228	move.l	#0x00002004, (%a1)+	/* 0x68 */
229	move.l	#0x00000000, (%a1)+	/* 0x6C */
230	move.l	#0x00100010, (%a1)+	/* 0x70 */
231	move.l	#0x00100010, (%a1)+	/* 0x74 */
232	move.l	#0x00000000, (%a1)+	/* 0x78 */
233	move.l	#0x07990000, (%a1)+	/* 0x7C */
234	move.l	#0xFC0B80A0, %a1
235	move.l	#0x00000000, (%a1)+	/* 0xA0 */
236	move.l	#0x00C80064, (%a1)+	/* 0xA4 */
237	move.l	#0x44520002, (%a1)+	/* 0xA8 */
238	move.l	#0x00C80023, (%a1)+	/* 0xAC */
239	move.l	#0xFC0B80B4, %a1
240	move.l	#0x0000C350, (%a1)	/* 0xB4 */
241	move.l	#0xFC0B80E0, %a1
242	move.l	#0x04000000, (%a1)+	/* 0xE0 */
243	move.l	#0x03000304, (%a1)+	/* 0xE4 */
244	move.l	#0x40040000, (%a1)+	/* 0xE8 */
245	move.l	#0xC0004004, (%a1)+	/* 0xEC */
246	move.l	#0x0642C000, (%a1)+	/* 0xF0 */
247	move.l	#0x00000642, (%a1)+	/* 0xF4 */
248	move.l	#0xFC0B8024, %a1
249	tpf
250	move.l	#0x01000100, (%a1)	/* 0x24 */
251
252	move.l	#0x2000, %d1
253	jsr	asm_delay
254#endif		/* CONFIG_MCF5441x */
255
256#ifdef CONFIG_MCF5445x
257	/* Dram Initialization a1, a2, and d0 */
258	/* mscr sdram */
259	move.l	#0xFC0A4074, %a1
260	move.b	#(CONFIG_SYS_SDRAM_DRV_STRENGTH), (%a1)
261	nop
262
263	/* SDRAM Chip 0 and 1 */
264	move.l	#0xFC0B8110, %a1
265	move.l	#0xFC0B8114, %a2
266
267	/* calculate the size */
268	move.l	#0x13, %d1
269	move.l	#(CONFIG_SYS_SDRAM_SIZE), %d2
270#ifdef CONFIG_SYS_SDRAM_BASE1
271	lsr.l	#1, %d2
272#endif
273
274dramsz_loop:
275	lsr.l	#1, %d2
276	add.l	#1, %d1
277	cmp.l	#1, %d2
278	bne	dramsz_loop
279#ifdef CONFIG_SYS_NAND_BOOT
280	beq	asm_nand_chk_status
281#endif
282	/* SDRAM Chip 0 and 1 */
283	move.l	#(CONFIG_SYS_SDRAM_BASE), (%a1)
284	or.l	%d1, (%a1)
285#ifdef CONFIG_SYS_SDRAM_BASE1
286	move.l	#(CONFIG_SYS_SDRAM_BASE1), (%a2)
287	or.l	%d1, (%a2)
288#endif
289	nop
290
291	/* dram cfg1 and cfg2 */
292	move.l	#0xFC0B8008, %a1
293	move.l	#(CONFIG_SYS_SDRAM_CFG1), (%a1)
294	nop
295	move.l	#0xFC0B800C, %a2
296	move.l	#(CONFIG_SYS_SDRAM_CFG2), (%a2)
297	nop
298
299	move.l	#0xFC0B8000, %a1	/* Mode */
300	move.l	#0xFC0B8004, %a2	/* Ctrl */
301
302	/* Issue PALL */
303	move.l	#(CONFIG_SYS_SDRAM_CTRL + 2), (%a2)
304	nop
305
306#ifdef CONFIG_M54455EVB
307	/* Issue LEMR */
308	move.l	#(CONFIG_SYS_SDRAM_EMOD + 0x408), (%a1)
309	nop
310	move.l	#(CONFIG_SYS_SDRAM_MODE + 0x300), (%a1)
311	nop
312#endif
313
314	move.l	#1000, %d1
315	jsr	asm_delay
316
317	/* Issue PALL */
318	move.l	#(CONFIG_SYS_SDRAM_CTRL + 2), (%a2)
319	nop
320
321	/* Perform two refresh cycles */
322	move.l	#(CONFIG_SYS_SDRAM_CTRL + 4), %d0
323	nop
324	move.l	%d0, (%a2)
325	move.l	%d0, (%a2)
326	nop
327
328#ifdef CONFIG_M54455EVB
329	move.l	#(CONFIG_SYS_SDRAM_MODE + 0x200), (%a1)
330	nop
331#elif defined(CONFIG_M54451EVB)
332	/* Issue LEMR */
333	move.l	#(CONFIG_SYS_SDRAM_MODE), (%a1)
334	nop
335	move.l	#(CONFIG_SYS_SDRAM_EMOD), (%a1)
336#endif
337
338	move.l	#500, %d1
339	jsr	asm_delay
340
341	move.l	#(CONFIG_SYS_SDRAM_CTRL), %d1
342	and.l	#0x7FFFFFFF, %d1
343#ifdef CONFIG_M54455EVB
344	or.l	#0x10000C00, %d1
345#elif defined(CONFIG_M54451EVB)
346	or.l	#0x10000C00, %d1
347#endif
348	move.l	%d1, (%a2)
349	nop
350
351	move.l	#2000, %d1
352	jsr	asm_delay
353#endif /* CONFIG_MCF5445x */
354
355#ifdef CONFIG_CF_SBF
356	/*
357	 * DSPI Initialization
358	 * a0 - general, sram - 0x80008000 - 32, see M54455EVB.h
359	 * a1 - dspi status
360	 * a2 - dtfr
361	 * a3 - drfr
362	 * a4 - Dst addr
363	 */
364	/* Enable pins for DSPI mode - chip-selects are enabled later */
365asm_dspi_init:
366#ifdef CONFIG_MCF5441x
367	move.l	#0xEC09404E, %a1
368	move.l	#0xEC09404F, %a2
369	move.b	#0xFF, (%a1)
370	move.b	#0x80, (%a2)
371#endif
372
373#ifdef CONFIG_MCF5445x
374	move.l	#0xFC0A4063, %a0
375	move.b	#0x7F, (%a0)
376#endif
377	/* Configure DSPI module */
378	move.l	#0xFC05C000, %a0
379	move.l	#0x80FF0C00, (%a0)	/* Master, clear TX/RX FIFO */
380
381	move.l	#0xFC05C00C, %a0
382#ifdef CONFIG_MCF5441x
383	move.l	#0x3E000016, (%a0)
384#endif
385#ifdef CONFIG_MCF5445x
386	move.l	#0x3E000011, (%a0)
387#endif
388
389	move.l	#0xFC05C034, %a2	/* dtfr */
390	move.l	#0xFC05C03B, %a3	/* drfr */
391
392	move.l	#(ASM_SBF_IMG_HDR + 4), %a1
393	move.l	(%a1)+, %d5
394	move.l	(%a1), %a4
395
396	move.l	#(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_SBFHDR_DATA_OFFSET), %a0
397	move.l	#(CONFIG_SYS_SBFHDR_SIZE), %d4
398
399	move.l	#0xFC05C02C, %a1	/* dspi status */
400
401	/* Issue commands and address */
402	move.l	#0x8002000B, %d2	/* Fast Read Cmd */
403	jsr	asm_dspi_wr_status
404	jsr	asm_dspi_rd_status
405
406	move.l	#0x80020000, %d2	/* Address byte 2 */
407	jsr	asm_dspi_wr_status
408	jsr	asm_dspi_rd_status
409
410	move.l	#0x80020000, %d2	/* Address byte 1 */
411	jsr	asm_dspi_wr_status
412	jsr	asm_dspi_rd_status
413
414	move.l	#0x80020000, %d2	/* Address byte 0 */
415	jsr	asm_dspi_wr_status
416	jsr	asm_dspi_rd_status
417
418	move.l	#0x80020000, %d2	/* Dummy Wr and Rd */
419	jsr	asm_dspi_wr_status
420	jsr	asm_dspi_rd_status
421
422	/* Transfer serial boot header to sram */
423asm_dspi_rd_loop1:
424	move.l	#0x80020000, %d2
425	jsr	asm_dspi_wr_status
426	jsr	asm_dspi_rd_status
427
428	move.b	%d1, (%a0)		/* read, copy to dst */
429
430	add.l	#1, %a0			/* inc dst by 1 */
431	sub.l	#1, %d4			/* dec cnt by 1 */
432	bne	asm_dspi_rd_loop1
433
434	/* Transfer u-boot from serial flash to memory */
435asm_dspi_rd_loop2:
436	move.l	#0x80020000, %d2
437	jsr	asm_dspi_wr_status
438	jsr	asm_dspi_rd_status
439
440	move.b	%d1, (%a4)		/* read, copy to dst */
441
442	add.l	#1, %a4			/* inc dst by 1 */
443	sub.l	#1, %d5			/* dec cnt by 1 */
444	bne	asm_dspi_rd_loop2
445
446	move.l	#0x00020000, %d2	/* Terminate */
447	jsr	asm_dspi_wr_status
448	jsr	asm_dspi_rd_status
449
450	/* jump to memory and execute */
451	move.l	#(CONFIG_SYS_TEXT_BASE + 0x400), %a0
452	jmp	(%a0)
453
454asm_dspi_wr_status:
455	move.l	(%a1), %d0		/* status */
456	and.l	#0x0000F000, %d0
457	cmp.l	#0x00003000, %d0
458	bgt	asm_dspi_wr_status
459
460	move.l	%d2, (%a2)
461	rts
462
463asm_dspi_rd_status:
464	move.l	(%a1), %d0		/* status */
465	and.l	#0x000000F0, %d0
466	lsr.l	#4, %d0
467	cmp.l	#0, %d0
468	beq	asm_dspi_rd_status
469
470	move.b	(%a3), %d1
471	rts
472#endif /* CONFIG_CF_SBF */
473
474#ifdef CONFIG_SYS_NAND_BOOT
475	/* copy 4 boot pages to dram as soon as possible */
476	/* each page is 996 bytes (1056 total with 60 ECC bytes */
477	move.l  #0x00000000, %a1	/* src */
478	move.l	#CONFIG_SYS_TEXT_BASE, %a2		/* dst */
479	move.l	#0x3E0, %d0		/* sz in long */
480
481asm_boot_nand_copy:
482	move.l	(%a1)+, (%a2)+
483	subq.l	#1, %d0
484	bne	asm_boot_nand_copy
485
486	/* jump to memory and execute */
487	move.l	#(asm_nand_init), %a0
488	jmp	(%a0)
489
490asm_nand_init:
491	/* exit nand boot-mode */
492	move.l	#0xFC0FFF30, %a1
493	or.l	#0x00000040, %d1
494	move.l	%d1, (%a1)
495
496	/* initialize general use internal ram */
497	move.l	#0, %d0
498	move.l	#(CACR_STATUS), %a1	/* CACR */
499	move.l	#(ICACHE_STATUS), %a2	/* icache */
500	move.l	#(DCACHE_STATUS), %a3	/* dcache */
501	move.l	%d0, (%a1)
502	move.l	%d0, (%a2)
503	move.l	%d0, (%a3)
504
505	/* invalidate and disable cache */
506	move.l	#0x01004100, %d0	/* Invalidate cache cmd */
507	movec	%d0, %CACR		/* Invalidate cache */
508	move.l	#0, %d0
509	movec	%d0, %ACR0
510	movec	%d0, %ACR1
511	movec	%d0, %ACR2
512	movec	%d0, %ACR3
513
514	/* Must disable global address */
515	move.l	#0xFC008000, %a1
516	move.l	#(CONFIG_SYS_CS0_BASE), (%a1)
517	move.l	#0xFC008008, %a1
518	move.l	#(CONFIG_SYS_CS0_CTRL), (%a1)
519	move.l	#0xFC008004, %a1
520	move.l	#(CONFIG_SYS_CS0_MASK), (%a1)
521
522	/* NAND port configuration */
523	move.l	#0xEC094048, %a1
524	move.b	#0xFD, (%a1)+
525	move.b	#0x5F, (%a1)+
526	move.b	#0x04, (%a1)+
527
528	/* reset nand */
529	move.l  #0xFC0FFF38, %a1	/* isr */
530	move.l  #0x000e0000, (%a1)
531	move.l	#0xFC0FFF08, %a2
532	move.l	#0x00000000, (%a2)+	/* car */
533	move.l	#0x11000000, (%a2)+	/* rar */
534	move.l	#0x00000000, (%a2)+	/* rpt */
535	move.l	#0x00000000, (%a2)+	/* rai */
536	move.l  #0xFC0FFF2c, %a2	/* cfg */
537	move.l  #0x00000000, (%a2)+	/* secsz */
538	move.l  #0x000e0681, (%a2)+
539	move.l  #0xFC0FFF04, %a2	/* cmd2 */
540	move.l  #0xFF404001, (%a2)
541	move.l  #0x000e0000, (%a1)
542
543	move.l	#0x2000, %d1
544	jsr	asm_delay
545
546	/* setup nand */
547	move.l  #0xFC0FFF00, %a1
548	move.l  #0x30700000, (%a1)+	/* cmd1 */
549	move.l  #0x007EF000, (%a1)+	/* cmd2 */
550
551	move.l  #0xFC0FFF2C, %a1
552	move.l  #0x00000841, (%a1)+	/* secsz */
553	move.l  #0x000e0681, (%a1)+	/* cfg */
554
555	move.l	#100, %d4		/* 100 pages ~200KB */
556	move.l	#4, %d2			/* start at 4 */
557	move.l  #0xFC0FFF04, %a0	/* cmd2 */
558	move.l  #0xFC0FFF0C, %a1	/* rar */
559	move.l	#(CONFIG_SYS_TEXT_BASE + 0xF80), %a2
560
561asm_nand_read:
562	move.l	#0x11000000, %d0	/* rar */
563	or.l	%d2, %d0
564	move.l	%d0, (%a1)
565	add.l	#1, %d2
566
567	move.l	(%a0), %d0		/* cmd2 */
568	or.l	#1, %d0
569	move.l	%d0, (%a0)
570
571	move.l	#0x200, %d1
572	jsr	asm_delay
573
574asm_nand_chk_status:
575	move.l  #0xFC0FFF38, %a4	/* isr */
576	move.l	(%a4), %d0
577	and.l	#0x40000000, %d0
578	tst.l	%d0
579	beq	asm_nand_chk_status
580
581	move.l  #0xFC0FFF38, %a4	/* isr */
582	move.l	(%a4), %d0
583	or.l	#0x000E0000, %d0
584	move.l	%d0, (%a4)
585
586	move.l	#0x200, %d3
587	move.l	#0xFC0FC000, %a3	/* buf 1 */
588asm_nand_copy:
589	move.l	(%a3)+, (%a2)+
590	subq.l	#1, %d3
591	bgt	asm_nand_copy
592
593	subq.l	#1, %d4
594	bgt	asm_nand_read
595
596	/* jump to memory and execute */
597	move.l	#(CONFIG_SYS_TEXT_BASE + 0x400), %a0
598	jmp	(%a0)
599
600#endif			/* CONFIG_SYS_NAND_BOOT */
601
602asm_delay:
603	nop
604	subq.l	#1, %d1
605	bne	asm_delay
606	rts
607#endif			/* CONFIG_CF_SBF || CONFIG_NAND_U_BOOT */
608
609.text
610	. = 0x400
611.globl _start
612_start:
613#if !defined(CONFIG_SERIAL_BOOT)
614	nop
615	nop
616	move.w	#0x2700,%sr		/* Mask off Interrupt */
617
618	/* Set vector base register at the beginning of the Flash */
619	move.l	#CONFIG_SYS_FLASH_BASE, %d0
620	movec	%d0, %VBR
621
622	move.l	#(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_CTRL), %d0
623	movec	%d0, %RAMBAR1
624
625	/* initialize general use internal ram */
626	move.l	#0, %d0
627	move.l	#(ICACHE_STATUS), %a1	/* icache */
628	move.l	#(DCACHE_STATUS), %a2	/* dcache */
629	move.l	%d0, (%a1)
630	move.l	%d0, (%a2)
631
632	/* invalidate and disable cache */
633	move.l	#(CONFIG_SYS_ICACHE_INV + CONFIG_SYS_DCACHE_INV), %d0
634	movec	%d0, %CACR		/* Invalidate cache */
635	move.l	#0, %d0
636	movec	%d0, %ACR0
637	movec	%d0, %ACR1
638	movec	%d0, %ACR2
639	movec	%d0, %ACR3
640#else
641	move.l	#(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_CTRL), %d0
642	movec	%d0, %RAMBAR1
643#endif
644
645	/* put relocation table address to a5 */
646	move.l	#__got_start, %a5
647
648	/* setup stack initially on top of internal static ram  */
649	move.l	#(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE), %sp
650
651	/*
652	 * if configured, malloc_f arena will be reserved first,
653	 * then (and always) gd struct space will be reserved
654	 */
655	move.l	%sp, -(%sp)
656	move.l	#board_init_f_alloc_reserve, %a1
657	jsr	(%a1)
658
659	/* update stack and frame-pointers */
660	move.l	%d0, %sp
661	move.l	%sp, %fp
662
663	/* initialize reserved area */
664	move.l	%d0, -(%sp)
665	move.l	#board_init_f_init_reserve, %a1
666	jsr	(%a1)
667
668	/* run low-level CPU init code (from flash) */
669	move.l	#cpu_init_f, %a1
670	jsr	(%a1)
671
672	/* run low-level board init code (from flash) */
673	clr.l   %sp@-
674	move.l	#board_init_f, %a1
675	jsr	(%a1)
676
677	/* board_init_f() does not return */
678
679/******************************************************************************/
680
681/*
682 * void relocate_code (addr_sp, gd, addr_moni)
683 *
684 * This "function" does not return, instead it continues in RAM
685 * after relocating the monitor code.
686 *
687 * r3 = dest
688 * r4 = src
689 * r5 = length in bytes
690 * r6 = cachelinesize
691 */
692.globl relocate_code
693relocate_code:
694	link.w	%a6,#0
695	move.l	8(%a6), %sp		/* set new stack pointer */
696
697	move.l	12(%a6), %d0		/* Save copy of Global Data pointer */
698	move.l	16(%a6), %a0		/* Save copy of Destination Address */
699
700	move.l	#CONFIG_SYS_MONITOR_BASE, %a1
701	move.l	#__init_end, %a2
702	move.l	%a0, %a3
703
704	/* copy the code to RAM */
7051:
706	move.l	(%a1)+, (%a3)+
707	cmp.l	%a1,%a2
708	bgt.s	1b
709
710/*
711 * We are done. Do not return, instead branch to second part of board
712 * initialization, now running from RAM.
713 */
714	move.l	%a0, %a1
715	add.l	#(in_ram - CONFIG_SYS_MONITOR_BASE), %a1
716	jmp	(%a1)
717
718in_ram:
719
720clear_bss:
721	/*
722	 * Now clear BSS segment
723	 */
724	move.l	%a0, %a1
725	add.l	#(_sbss - CONFIG_SYS_MONITOR_BASE),%a1
726	move.l	%a0, %d1
727	add.l	#(_ebss - CONFIG_SYS_MONITOR_BASE),%d1
7286:
729	clr.l	(%a1)+
730	cmp.l	%a1,%d1
731	bgt.s	6b
732
733	/*
734	 * fix got table in RAM
735	 */
736	move.l	%a0, %a1
737	add.l	#(__got_start - CONFIG_SYS_MONITOR_BASE),%a1
738	move.l	%a1,%a5			/* fix got pointer register a5 */
739
740	move.l	%a0, %a2
741	add.l	#(__got_end - CONFIG_SYS_MONITOR_BASE),%a2
742
7437:
744	move.l	(%a1),%d1
745	sub.l	#_start,%d1
746	add.l	%a0,%d1
747	move.l	%d1,(%a1)+
748	cmp.l	%a2, %a1
749	bne	7b
750
751	/* calculate relative jump to board_init_r in ram */
752	move.l	%a0, %a1
753	add.l	#(board_init_r - CONFIG_SYS_MONITOR_BASE), %a1
754
755	/* set parameters for board_init_r */
756	move.l	%a0,-(%sp)		/* dest_addr */
757	move.l	%d0,-(%sp)		/* gd */
758	jsr	(%a1)
759
760/******************************************************************************/
761
762/* exception code */
763.globl _fault
764_fault:
765	bra	_fault
766
767.globl _exc_handler
768_exc_handler:
769	SAVE_ALL
770	movel	%sp,%sp@-
771	bsr	exc_handler
772	addql	#4,%sp
773	RESTORE_ALL
774
775.globl _int_handler
776_int_handler:
777	SAVE_ALL
778	movel	%sp,%sp@-
779	bsr	int_handler
780	addql	#4,%sp
781	RESTORE_ALL
782
783/******************************************************************************/
784
785.globl version_string
786version_string:
787.ascii U_BOOT_VERSION_STRING, "\0"
788.align 4
789