1if ARCH_ZYNQMP 2 3config SPL_FS_FAT 4 default y 5 6config SPL_LIBCOMMON_SUPPORT 7 default y 8 9config SPL_LIBDISK_SUPPORT 10 default y 11 12config SPL_LIBGENERIC_SUPPORT 13 default y 14 15config SPL_MMC_SUPPORT 16 default y if MMC_SDHCI_ZYNQ 17 18config SPL_SERIAL_SUPPORT 19 default y 20 21config SPL_SPI_FLASH_SUPPORT 22 default y if ZYNQ_QSPI 23 24config SPL_SPI_SUPPORT 25 default y if ZYNQ_QSPI 26 27config SYS_BOARD 28 default "zynqmp" 29 30config SYS_VENDOR 31 string "Vendor name" 32 default "xilinx" 33 34config SYS_SOC 35 default "zynqmp" 36 37config SYS_CONFIG_NAME 38 string "Board configuration name" 39 default "xilinx_zynqmp" 40 help 41 This option contains information about board configuration name. 42 Based on this option include/configs/<CONFIG_SYS_CONFIG_NAME>.h header 43 will be used for board configuration. 44 45config SYS_MEM_RSVD_FOR_MMU 46 bool "Reserve memory for MMU Table" 47 help 48 If defined this option is used to setup different space for 49 MMU table than the one which will be allocated during 50 relocation. 51 52config BOOT_INIT_FILE 53 string "boot.bin init register filename" 54 depends on SPL 55 default "" 56 help 57 Add register writes to boot.bin format (max 256 pairs). 58 Expect a table of register-value pairs, e.g. "0x12345678 0x4321" 59 60config PMUFW_INIT_FILE 61 string "PMU firmware" 62 depends on SPL 63 default "" 64 help 65 Include external PMUFW (Platform Management Unit FirmWare) to 66 a Xilinx bootable image (boot.bin). 67 68config ZYNQMP_USB 69 bool "Configure ZynqMP USB" 70 71config ZYNQMP_NO_DDR 72 bool "Disable DDR MMU mapping" 73 help 74 This option configures MMU with no DDR to avoid speculative 75 access to DDR memory where DDR is not present. 76 77config SYS_MALLOC_F_LEN 78 default 0x600 79 80config DEFINE_TCM_OCM_MMAP 81 bool "Define TCM and OCM memory in MMU Table" 82 default y if MP 83 help 84 This option if enabled defines the TCM and OCM memory and its 85 memory attributes in MMU table entry. 86 87config ZYNQMP_PSU_INIT_ENABLED 88 bool "Include psu_init" 89 help 90 Include psu_init to full u-boot. SPL include psu_init by default. 91 92config SPL_ZYNQMP_ALT_BOOTMODE_ENABLED 93 bool "Overwrite SPL bootmode" 94 depends on SPL 95 help 96 Overwrite bootmode selected via boot mode pins to tell SPL what should 97 be the next boot device. 98 99config ZYNQ_SDHCI_MAX_FREQ 100 default 200000000 101 102config SPL_ZYNQMP_ALT_BOOTMODE 103 hex 104 default 0x0 if JTAG_MODE 105 default 0x1 if QSPI_MODE_24BIT 106 default 0x2 if QSPI_MODE_32BIT 107 default 0x3 if SD_MODE 108 default 0x4 if NAND_MODE 109 default 0x5 if SD_MODE1 110 default 0x6 if EMMC_MODE 111 default 0x7 if USB_MODE 112 default 0xa if SW_USBHOST_MODE 113 default 0xb if SW_SATA_MODE 114 default 0xe if SD1_LSHFT_MODE 115 116choice 117 prompt "Boot mode" 118 depends on SPL_ZYNQMP_ALT_BOOTMODE_ENABLED 119 default JTAG_MODE 120 121config JTAG_MODE 122 bool "JTAG_MODE" 123 124config QSPI_MODE_24BIT 125 bool "QSPI_MODE_24BIT" 126 127config QSPI_MODE_32BIT 128 bool "QSPI_MODE_32BIT" 129 130config SD_MODE 131 bool "SD_MODE" 132 133config SD_MODE1 134 bool "SD_MODE1" 135 136config NAND_MODE 137 bool "NAND_MODE" 138 139config EMMC_MODE 140 bool "EMMC_MODE" 141 142config USB_MODE 143 bool "USB" 144 145config SW_USBHOST_MODE 146 bool "SW USBHOST_MODE" 147 148config SW_SATA_MODE 149 bool "SW SATA_MODE" 150 151config SD1_LSHFT_MODE 152 bool "SD1_LSHFT_MODE" 153 154endchoice 155 156endif 157