1/*
2 * Copyright (C) 2012-2015 Masahiro Yamada <yamada.masahiro@socionext.com>
3 *
4 * SPDX-License-Identifier:	GPL-2.0+
5 */
6
7#include <config.h>
8#include <linux/linkage.h>
9#include <linux/sizes.h>
10#include <asm/system.h>
11
12#include "ssc-regs.h"
13
14ENTRY(lowlevel_init)
15	mov	r8, lr			@ persevere link reg across call
16
17	/*
18	 * The UniPhier Boot ROM loads SPL code to the L2 cache.
19	 * But CPUs can only do instruction fetch now because start.S has
20	 * cleared C and M bits.
21	 * First we need to turn on MMU and Dcache again to get back
22	 * data access to L2.
23	 */
24	mrc	p15, 0, r0, c1, c0, 0	@ SCTLR (System Control Register)
25	orr	r0, r0, #(CR_C | CR_M)	@ enable MMU and Dcache
26	mcr	p15, 0, r0, c1, c0, 0
27
28#ifdef CONFIG_DEBUG_LL
29	bl	debug_ll_init
30#endif
31
32	bl	setup_init_ram		@ RAM area for stack and page table
33
34	/*
35	 * Now we are using the page table embedded in the Boot ROM.
36	 * It is not handy since it is not a straight mapped table for sLD3.
37	 * Also, the access to the external bus is prohibited.  What we need
38	 * to do next is to create a page table and switch over to it.
39	 */
40	bl	create_page_table
41	bl	__v7_flush_dcache_all
42
43	/* Disable MMU and Dcache before switching Page Table */
44	mrc	p15, 0, r0, c1, c0, 0	@ SCTLR (System Control Register)
45	bic	r0, r0, #(CR_C | CR_M)	@ disable MMU and Dcache
46	mcr	p15, 0, r0, c1, c0, 0
47
48	bl	enable_mmu
49
50	mov	lr, r8			@ restore link
51	mov	pc, lr			@ back to my caller
52ENDPROC(lowlevel_init)
53
54ENTRY(enable_mmu)
55	mrc	p15, 0, r0, c2, c0, 2	@ TTBCR (Translation Table Base Control Register)
56	bic	r0, r0, #0x37
57	orr	r0, r0, #0x20		@ disable TTBR1
58	mcr	p15, 0, r0, c2, c0, 2
59
60	orr	r0, r12, #0x8		@ Outer Cacheability for table walks: WBWA
61	mcr	p15, 0, r0, c2, c0, 0   @ TTBR0
62
63	mov	r0, #0
64	mcr	p15, 0, r0, c8, c7, 0	@ invalidate TLBs
65
66	mov	r0, #-1			@ manager for all domains (No permission check)
67	mcr	p15, 0, r0, c3, c0, 0   @ DACR (Domain Access Control Register)
68
69	dsb
70	isb
71	/*
72	 * MMU on:
73	 * TLBs was already invalidated in "../start.S"
74	 * So, we don't need to invalidate it here.
75	 */
76	mrc	p15, 0, r0, c1, c0, 0	@ SCTLR (System Control Register)
77	orr	r0, r0, #(CR_C | CR_M)	@ MMU and Dcache enable
78	mcr	p15, 0, r0, c1, c0, 0
79
80	mov	pc, lr
81ENDPROC(enable_mmu)
82
83/*
84 * For PH1-Pro4 or older SoCs, the size of WAY is 32KB.
85 * It is large enough for tmp RAM.
86 */
87#define BOOT_RAM_SIZE	(SZ_32K)
88#define BOOT_RAM_BASE	((CONFIG_SPL_STACK) - (BOOT_RAM_SIZE))
89#define BOOT_WAY_BITS	(0x00000100)   /* way 8 */
90
91ENTRY(setup_init_ram)
92	/*
93	 * Touch to zero for the boot way
94	 */
950:
96	/*
97	 * set SSCOQM, SSCOQAD, SSCOQSZ, SSCOQWN in this order
98	 */
99	ldr	r0, = 0x00408006	@ touch to zero with address range
100	ldr	r1, = SSCOQM
101	str	r0, [r1]
102	ldr	r0, = BOOT_RAM_BASE
103	ldr	r1, = SSCOQAD
104	str	r0, [r1]
105	ldr	r0, = BOOT_RAM_SIZE
106	ldr	r1, = SSCOQSZ
107	str	r0, [r1]
108	ldr	r0, = BOOT_WAY_BITS
109	ldr	r1, = SSCOQWN
110	str	r0, [r1]
111	ldr	r1, = SSCOPPQSEF
112	ldr	r0, [r1]
113	cmp	r0, #0			@ check if the command is successfully set
114	bne	0b			@ try again if an error occurs
115
116	ldr	r1, = SSCOLPQS
1171:
118	ldr	r0, [r1]
119	cmp	r0, #0x4
120	bne	1b			@ wait until the operation is completed
121	str	r0, [r1]		@ clear the complete notification flag
122
123	mov	pc, lr
124ENDPROC(setup_init_ram)
125
126#define DEVICE	0x00002002 /* Non-shareable Device */
127#define NORMAL	0x0000000e /* Normal Memory Write-Back, No Write-Allocate */
128
129ENTRY(create_page_table)
130	ldr	r0, = DEVICE
131	ldr	r1, = BOOT_RAM_BASE
132	mov	r12, r1			@ r12 is preserved during D-cache flush
1330:	str	r0, [r1], #4		@ specify all the sections as Device
134	adds	r0, r0, #0x00100000
135	bcc	0b
136
137	ldr	r0, = NORMAL
138	str	r0, [r12]		@ mark the first section as Normal
139	add	r0, r0, #0x00100000
140	str	r0, [r12, #4]		@ mark the second section as Normal
141	mov	pc, lr
142ENDPROC(create_page_table)
143