1if ARCH_UNIPHIER 2 3config SYS_CONFIG_NAME 4 default "uniphier" 5 6choice 7 prompt "UniPhier SoC select" 8 default ARCH_UNIPHIER_PRO4 9 10config ARCH_UNIPHIER_SLD3 11 bool "UniPhier PH1-sLD3 SoC" 12 select CPU_V7 13 14config ARCH_UNIPHIER_LD4_SLD8 15 bool "UniPhier PH1-LD4/PH1-sLD8 SoC" 16 select CPU_V7 17 18config ARCH_UNIPHIER_PRO4 19 bool "UniPhier PH1-Pro4 SoC" 20 select CPU_V7 21 22config ARCH_UNIPHIER_PRO5_PXS2_LD6B 23 bool "UniPhier PH1-Pro5/ProXstream2/PH1-LD6b SoC" 24 select CPU_V7 25 26config ARCH_UNIPHIER_LD20 27 bool "UniPhier PH1-LD20 SoC" 28 select ARM64 29 select SPL_SEPARATE_BSS 30 31endchoice 32 33config ARCH_UNIPHIER_LD4 34 bool "Enable UniPhier PH1-LD4 SoC support" 35 depends on ARCH_UNIPHIER_LD4_SLD8 36 default y 37 38config ARCH_UNIPHIER_SLD8 39 bool "Enable UniPhier PH1-sLD8 SoC support" 40 depends on ARCH_UNIPHIER_LD4_SLD8 41 default y 42 43config ARCH_UNIPHIER_PRO5 44 bool "Enable UniPhier PH1-Pro5 SoC support" 45 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B 46 default y 47 48config ARCH_UNIPHIER_PXS2 49 bool "Enable UniPhier ProXstream2 SoC support" 50 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B 51 default y 52 53config ARCH_UNIPHIER_LD6B 54 bool "Enable UniPhier PH1-LD6b SoC support" 55 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B 56 default y 57 58config MICRO_SUPPORT_CARD 59 bool "Use Micro Support Card" 60 help 61 This option provides support for the expansion board, available 62 on some UniPhier reference boards. 63 64 Say Y to use the on-board UART, Ether, LED devices. 65 66config CMD_PINMON 67 bool "Enable boot mode pins monitor command" 68 default y 69 help 70 The command "pinmon" shows the state of the boot mode pins. 71 The boot mode pins are latched when the system reset is deasserted 72 and determine which device the system should load a boot image from. 73 74config CMD_DDRPHY_DUMP 75 bool "Enable dump command of DDR PHY parameters" 76 depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || ARCH_UNIPHIER_SLD8 77 default y 78 help 79 The command "ddrphy" shows the resulting parameters of DDR PHY 80 training; it is useful for the evaluation of DDR PHY training. 81 82config CMD_DDRMPHY_DUMP 83 bool "Enable dump command of DDR Multi PHY parameters" 84 depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B 85 default y 86 help 87 The command "ddrmphy" shows the resulting parameters of DDR Multi PHY 88 training; it is useful for the evaluation of DDR Multi PHY training. 89 90endif 91