1if ARCH_UNIPHIER 2 3config SYS_CONFIG_NAME 4 default "uniphier" 5 6config ARCH_UNIPHIER_32BIT 7 bool 8 select CPU_V7 9 select CPU_V7_HAS_NONSEC 10 select ARMV7_NONSEC 11 select ARCH_SUPPORT_PSCI 12 13choice 14 prompt "UniPhier SoC select" 15 default ARCH_UNIPHIER_V8_MULTI 16 17config ARCH_UNIPHIER_LD4_SLD8 18 bool "UniPhier LD4/sLD8 SoCs" 19 select ARCH_UNIPHIER_32BIT 20 21config ARCH_UNIPHIER_V7_MULTI 22 bool "UniPhier Pro4/Pro5/PXs2/LD6b SoCs" 23 select ARCH_UNIPHIER_32BIT 24 25config ARCH_UNIPHIER_V8_MULTI 26 bool "UniPhier V8 SoCs" 27 depends on !SPL 28 select ARM64 29 select CMD_UNZIP 30 31endchoice 32 33config ARCH_UNIPHIER_LD4 34 bool "Enable UniPhier LD4 SoC support" 35 depends on ARCH_UNIPHIER_LD4_SLD8 36 default y 37 38config ARCH_UNIPHIER_SLD8 39 bool "Enable UniPhier sLD8 SoC support" 40 depends on ARCH_UNIPHIER_LD4_SLD8 41 default y 42 43config ARCH_UNIPHIER_PRO4 44 bool "Enable UniPhier Pro4 SoC support" 45 depends on ARCH_UNIPHIER_V7_MULTI 46 default y 47 48config ARCH_UNIPHIER_PRO5 49 bool "Enable UniPhier Pro5 SoC support" 50 depends on ARCH_UNIPHIER_V7_MULTI 51 default y 52 53config ARCH_UNIPHIER_PXS2 54 bool "Enable UniPhier Pxs2 SoC support" 55 depends on ARCH_UNIPHIER_V7_MULTI 56 default y 57 58config ARCH_UNIPHIER_LD6B 59 bool "Enable UniPhier LD6b SoC support" 60 depends on ARCH_UNIPHIER_V7_MULTI 61 default y 62 63config ARCH_UNIPHIER_LD11 64 bool "Enable UniPhier LD11 SoC support" 65 depends on ARCH_UNIPHIER_V8_MULTI 66 default y 67 68config ARCH_UNIPHIER_LD20 69 bool "Enable UniPhier LD20 SoC support" 70 depends on ARCH_UNIPHIER_V8_MULTI 71 select OF_BOARD_SETUP 72 default y 73 74config ARCH_UNIPHIER_PXS3 75 bool "Enable UniPhier PXs3 SoC support" 76 depends on ARCH_UNIPHIER_V8_MULTI 77 default y 78 79config CACHE_UNIPHIER 80 bool "Enable the UniPhier L2 cache controller" 81 depends on ARCH_UNIPHIER_32BIT 82 select SYS_CACHE_SHIFT_7 83 default y 84 help 85 This option allows to use the UniPhier System Cache as L2 cache. 86 87config MICRO_SUPPORT_CARD 88 bool "Use Micro Support Card" 89 help 90 This option provides support for the expansion board, available 91 on some UniPhier reference boards. 92 93 Say Y to use the on-board UART, Ether, LED devices. 94 95config CMD_PINMON 96 bool "Enable boot mode pins monitor command" 97 default y 98 help 99 The command "pinmon" shows the state of the boot mode pins. 100 The boot mode pins are latched when the system reset is deasserted 101 and determine which device the system should load a boot image from. 102 103config CMD_DDRPHY_DUMP 104 bool "Enable dump command of DDR PHY parameters" 105 depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || \ 106 ARCH_UNIPHIER_SLD8 || ARCH_UNIPHIER_LD11 107 default y 108 help 109 The command "ddrphy" shows the resulting parameters of DDR PHY 110 training; it is useful for the evaluation of DDR PHY training. 111 112config CMD_DDRMPHY_DUMP 113 bool "Enable dump command of DDR Multi PHY parameters" 114 depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B 115 default y 116 help 117 The command "ddrmphy" shows the resulting parameters of DDR Multi PHY 118 training; it is useful for the evaluation of DDR Multi PHY training. 119 120endif 121