xref: /openbmc/u-boot/arch/arm/mach-uniphier/Kconfig (revision 8b7d51249eca113c4965a7c417f33d7eb569434b)
1if ARCH_UNIPHIER
2
3config SYS_CONFIG_NAME
4	default "uniphier"
5
6config ARCH_UNIPHIER_32BIT
7	bool
8	select CPU_V7
9	select CPU_V7_HAS_NONSEC
10	select ARMV7_NONSEC
11
12config ARCH_UNIPHIER_64BIT
13	bool
14	select ARM64
15	select SPL_SEPARATE_BSS
16	select ARMV8_MULTIENTRY
17	select ARMV8_SPIN_TABLE
18
19choice
20        prompt "UniPhier SoC select"
21        default ARCH_UNIPHIER_PRO4
22
23config ARCH_UNIPHIER_SLD3
24	bool "UniPhier PH1-sLD3 SoC"
25	select ARCH_UNIPHIER_32BIT
26
27config ARCH_UNIPHIER_LD4_SLD8
28	bool "UniPhier PH1-LD4/PH1-sLD8 SoC"
29	select ARCH_UNIPHIER_32BIT
30
31config ARCH_UNIPHIER_PRO4
32	bool "UniPhier PH1-Pro4 SoC"
33	select ARCH_UNIPHIER_32BIT
34
35config ARCH_UNIPHIER_PRO5_PXS2_LD6B
36	bool "UniPhier PH1-Pro5/ProXstream2/PH1-LD6b SoC"
37	select ARCH_UNIPHIER_32BIT
38
39config ARCH_UNIPHIER_LD11
40	bool "UniPhier PH1-LD11 SoC"
41	select ARCH_UNIPHIER_64BIT
42
43config ARCH_UNIPHIER_LD20
44	bool "UniPhier PH1-LD20 SoC"
45	select ARCH_UNIPHIER_64BIT
46	select OF_BOARD_SETUP
47
48endchoice
49
50config ARCH_UNIPHIER_LD4
51	bool "Enable UniPhier PH1-LD4 SoC support"
52	depends on ARCH_UNIPHIER_LD4_SLD8
53	default y
54
55config ARCH_UNIPHIER_SLD8
56	bool "Enable UniPhier PH1-sLD8 SoC support"
57	depends on ARCH_UNIPHIER_LD4_SLD8
58	default y
59
60config ARCH_UNIPHIER_PRO5
61	bool "Enable UniPhier PH1-Pro5 SoC support"
62	depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
63	default y
64
65config ARCH_UNIPHIER_PXS2
66	bool "Enable UniPhier ProXstream2 SoC support"
67	depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
68	default y
69
70config ARCH_UNIPHIER_LD6B
71	bool "Enable UniPhier PH1-LD6b SoC support"
72	depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
73	default y
74
75config CACHE_UNIPHIER
76	bool "Enable the UniPhier L2 cache controller"
77	depends on ARCH_UNIPHIER_32BIT
78	select SYS_CACHE_SHIFT_7
79	default y
80	help
81	  This option allows to use the UniPhier System Cache as L2 cache.
82
83config MICRO_SUPPORT_CARD
84	bool "Use Micro Support Card"
85	help
86	  This option provides support for the expansion board, available
87	  on some UniPhier reference boards.
88
89	  Say Y to use the on-board UART, Ether, LED devices.
90
91config CMD_PINMON
92	bool "Enable boot mode pins monitor command"
93	default y
94	help
95	  The command "pinmon" shows the state of the boot mode pins.
96	  The boot mode pins are latched when the system reset is deasserted
97	  and determine which device the system should load a boot image from.
98
99config CMD_DDRPHY_DUMP
100	bool "Enable dump command of DDR PHY parameters"
101	depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || ARCH_UNIPHIER_SLD8
102	default y
103	help
104	  The command "ddrphy" shows the resulting parameters of DDR PHY
105	  training; it is useful for the evaluation of DDR PHY training.
106
107config CMD_DDRMPHY_DUMP
108	bool "Enable dump command of DDR Multi PHY parameters"
109	depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
110	default y
111	help
112	  The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
113	  training; it is useful for the evaluation of DDR Multi PHY training.
114
115endif
116