xref: /openbmc/u-boot/arch/arm/mach-uniphier/Kconfig (revision 6fa0d345)
1if ARCH_UNIPHIER
2
3config SYS_CONFIG_NAME
4	default "uniphier"
5
6config ARCH_UNIPHIER_32BIT
7	bool
8	select CPU_V7
9	select CPU_V7_HAS_NONSEC
10	select ARMV7_NONSEC
11	select ARCH_SUPPORT_PSCI
12
13config ARCH_UNIPHIER_64BIT
14	bool
15	select ARM64
16	select SPL_SEPARATE_BSS
17	select ARMV8_MULTIENTRY
18	select ARMV8_SPIN_TABLE
19
20choice
21        prompt "UniPhier SoC select"
22        default ARCH_UNIPHIER_PRO4
23
24config ARCH_UNIPHIER_SLD3
25	bool "UniPhier PH1-sLD3 SoC"
26	select ARCH_UNIPHIER_32BIT
27
28config ARCH_UNIPHIER_LD4_SLD8
29	bool "UniPhier PH1-LD4/PH1-sLD8 SoC"
30	select ARCH_UNIPHIER_32BIT
31
32config ARCH_UNIPHIER_PRO4
33	bool "UniPhier PH1-Pro4 SoC"
34	select ARCH_UNIPHIER_32BIT
35
36config ARCH_UNIPHIER_PRO5_PXS2_LD6B
37	bool "UniPhier PH1-Pro5/ProXstream2/PH1-LD6b SoC"
38	select ARCH_UNIPHIER_32BIT
39
40config ARCH_UNIPHIER_LD11
41	bool "UniPhier PH1-LD11 SoC"
42	select ARCH_UNIPHIER_64BIT
43
44config ARCH_UNIPHIER_LD20
45	bool "UniPhier PH1-LD20 SoC"
46	select ARCH_UNIPHIER_64BIT
47	select OF_BOARD_SETUP
48
49endchoice
50
51config ARCH_UNIPHIER_LD4
52	bool "Enable UniPhier PH1-LD4 SoC support"
53	depends on ARCH_UNIPHIER_LD4_SLD8
54	default y
55
56config ARCH_UNIPHIER_SLD8
57	bool "Enable UniPhier PH1-sLD8 SoC support"
58	depends on ARCH_UNIPHIER_LD4_SLD8
59	default y
60
61config ARCH_UNIPHIER_PRO5
62	bool "Enable UniPhier PH1-Pro5 SoC support"
63	depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
64	default y
65
66config ARCH_UNIPHIER_PXS2
67	bool "Enable UniPhier ProXstream2 SoC support"
68	depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
69	default y
70
71config ARCH_UNIPHIER_LD6B
72	bool "Enable UniPhier PH1-LD6b SoC support"
73	depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
74	default y
75
76config CACHE_UNIPHIER
77	bool "Enable the UniPhier L2 cache controller"
78	depends on ARCH_UNIPHIER_32BIT
79	select SYS_CACHE_SHIFT_7
80	default y
81	help
82	  This option allows to use the UniPhier System Cache as L2 cache.
83
84config MICRO_SUPPORT_CARD
85	bool "Use Micro Support Card"
86	help
87	  This option provides support for the expansion board, available
88	  on some UniPhier reference boards.
89
90	  Say Y to use the on-board UART, Ether, LED devices.
91
92config CMD_PINMON
93	bool "Enable boot mode pins monitor command"
94	default y
95	help
96	  The command "pinmon" shows the state of the boot mode pins.
97	  The boot mode pins are latched when the system reset is deasserted
98	  and determine which device the system should load a boot image from.
99
100config CMD_DDRPHY_DUMP
101	bool "Enable dump command of DDR PHY parameters"
102	depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || \
103		ARCH_UNIPHIER_SLD8 || ARCH_UNIPHIER_LD11
104	default y
105	help
106	  The command "ddrphy" shows the resulting parameters of DDR PHY
107	  training; it is useful for the evaluation of DDR PHY training.
108
109config CMD_DDRMPHY_DUMP
110	bool "Enable dump command of DDR Multi PHY parameters"
111	depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
112	default y
113	help
114	  The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
115	  training; it is useful for the evaluation of DDR Multi PHY training.
116
117endif
118