1if ARCH_UNIPHIER 2 3config SYS_CONFIG_NAME 4 default "uniphier" 5 6choice 7 prompt "UniPhier SoC select" 8 default ARCH_UNIPHIER_PH1_PRO4 9 10config ARCH_UNIPHIER_PH1_SLD3 11 bool "UniPhier PH1-sLD3 SoC" 12 select CPU_V7 13 14config ARCH_UNIPHIER_LD4_SLD8 15 bool "UniPhier PH1-LD4/PH1-sLD8 SoC" 16 select CPU_V7 17 18config ARCH_UNIPHIER_PH1_PRO4 19 bool "UniPhier PH1-Pro4 SoC" 20 select CPU_V7 21 22config ARCH_UNIPHIER_PRO5_PXS2_LD6B 23 bool "UniPhier PH1-Pro5/ProXstream2/PH1-LD6b SoC" 24 select CPU_V7 25 26endchoice 27 28config ARCH_UNIPHIER_PH1_LD4 29 bool "Enable UniPhier PH1-LD4 SoC support" 30 depends on ARCH_UNIPHIER_LD4_SLD8 31 default y 32 33config ARCH_UNIPHIER_PH1_SLD8 34 bool "Enable UniPhier PH1-sLD8 SoC support" 35 depends on ARCH_UNIPHIER_LD4_SLD8 36 default y 37 38config ARCH_UNIPHIER_PH1_PRO5 39 bool "Enable UniPhier PH1-Pro5 SoC support" 40 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B 41 default y 42 43config ARCH_UNIPHIER_PROXSTREAM2 44 bool "Enable UniPhier ProXstream2 SoC support" 45 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B 46 default y 47 48config ARCH_UNIPHIER_PH1_LD6B 49 bool "Enable UniPhier PH1-LD6b SoC support" 50 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B 51 default y 52 53config MICRO_SUPPORT_CARD 54 bool "Use Micro Support Card" 55 help 56 This option provides support for the expansion board, available 57 on some UniPhier reference boards. 58 59 Say Y to use the on-board UART, Ether, LED devices. 60 61config CMD_PINMON 62 bool "Enable boot mode pins monitor command" 63 default y 64 help 65 The command "pinmon" shows the state of the boot mode pins. 66 The boot mode pins are latched when the system reset is deasserted 67 and determine which device the system should load a boot image from. 68 69config CMD_DDRPHY_DUMP 70 bool "Enable dump command of DDR PHY parameters" 71 depends on ARCH_UNIPHIER_PH1_LD4 || ARCH_UNIPHIER_PH1_PRO4 || \ 72 ARCH_UNIPHIER_PH1_SLD8 73 help 74 The command "ddrphy" shows the resulting parameters of DDR PHY 75 training; it is useful for the evaluation of DDR PHY training. 76 77config CMD_DDRMPHY_DUMP 78 bool "Enable dump command of DDR Multi PHY parameters" 79 depends on ARCH_UNIPHIER_PROXSTREAM2 || ARCH_UNIPHIER_PH1_LD6B 80 help 81 The command "ddrmphy" shows the resulting parameters of DDR Multi PHY 82 training; it is useful for the evaluation of DDR Multi PHY training. 83 84endif 85