1if ARCH_UNIPHIER 2 3config SYS_CONFIG_NAME 4 default "uniphier" 5 6choice 7 prompt "UniPhier SoC select" 8 default ARCH_UNIPHIER_PRO4 9 10config ARCH_UNIPHIER_SLD3 11 bool "UniPhier PH1-sLD3 SoC" 12 select CPU_V7 13 14config ARCH_UNIPHIER_LD4_SLD8 15 bool "UniPhier PH1-LD4/PH1-sLD8 SoC" 16 select CPU_V7 17 18config ARCH_UNIPHIER_PRO4 19 bool "UniPhier PH1-Pro4 SoC" 20 select CPU_V7 21 22config ARCH_UNIPHIER_PRO5_PXS2_LD6B 23 bool "UniPhier PH1-Pro5/ProXstream2/PH1-LD6b SoC" 24 select CPU_V7 25 26config ARCH_UNIPHIER_LD11 27 bool "UniPhier PH1-LD11 SoC" 28 select ARM64 29 select SPL_SEPARATE_BSS 30 31config ARCH_UNIPHIER_LD20 32 bool "UniPhier PH1-LD20 SoC" 33 select ARM64 34 select SPL_SEPARATE_BSS 35 36endchoice 37 38config ARCH_UNIPHIER_LD4 39 bool "Enable UniPhier PH1-LD4 SoC support" 40 depends on ARCH_UNIPHIER_LD4_SLD8 41 default y 42 43config ARCH_UNIPHIER_SLD8 44 bool "Enable UniPhier PH1-sLD8 SoC support" 45 depends on ARCH_UNIPHIER_LD4_SLD8 46 default y 47 48config ARCH_UNIPHIER_PRO5 49 bool "Enable UniPhier PH1-Pro5 SoC support" 50 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B 51 default y 52 53config ARCH_UNIPHIER_PXS2 54 bool "Enable UniPhier ProXstream2 SoC support" 55 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B 56 default y 57 58config ARCH_UNIPHIER_LD6B 59 bool "Enable UniPhier PH1-LD6b SoC support" 60 depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B 61 default y 62 63config MICRO_SUPPORT_CARD 64 bool "Use Micro Support Card" 65 help 66 This option provides support for the expansion board, available 67 on some UniPhier reference boards. 68 69 Say Y to use the on-board UART, Ether, LED devices. 70 71config CMD_PINMON 72 bool "Enable boot mode pins monitor command" 73 default y 74 help 75 The command "pinmon" shows the state of the boot mode pins. 76 The boot mode pins are latched when the system reset is deasserted 77 and determine which device the system should load a boot image from. 78 79config CMD_DDRPHY_DUMP 80 bool "Enable dump command of DDR PHY parameters" 81 depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || ARCH_UNIPHIER_SLD8 82 default y 83 help 84 The command "ddrphy" shows the resulting parameters of DDR PHY 85 training; it is useful for the evaluation of DDR PHY training. 86 87config CMD_DDRMPHY_DUMP 88 bool "Enable dump command of DDR Multi PHY parameters" 89 depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B 90 default y 91 help 92 The command "ddrmphy" shows the resulting parameters of DDR Multi PHY 93 training; it is useful for the evaluation of DDR Multi PHY training. 94 95endif 96