xref: /openbmc/u-boot/arch/arm/mach-uniphier/Kconfig (revision 2e33df80)
1if ARCH_UNIPHIER
2
3config SYS_CONFIG_NAME
4	default "uniphier"
5
6config ARCH_UNIPHIER_PH1_SLD3
7	bool "UniPhier PH1-sLD3 SoC"
8	help
9	  This enables support for UniPhier PH1-sLD3 SoC.
10
11config ARCH_UNIPHIER_PH1_LD4
12	bool "UniPhier PH1-LD4 SoC"
13	depends on !ARCH_UNIPHIER_PH1_SLD3
14	help
15	  This enables support for UniPhier PH1-LD4 SoC.
16
17config ARCH_UNIPHIER_PH1_PRO4
18	bool "UniPhier PH1-Pro4 SoC"
19	depends on !ARCH_UNIPHIER_PH1_SLD3 && \
20		   !ARCH_UNIPHIER_PH1_LD4 && \
21		   !ARCH_UNIPHIER_PH1_SLD8
22	help
23	  This enables support for UniPhier PH1-Pro4 SoC.
24
25config ARCH_UNIPHIER_PH1_SLD8
26	bool "UniPhier PH1-sLD8 SoC"
27	depends on !ARCH_UNIPHIER_PH1_SLD3
28	help
29	  This enables support for UniPhier PH1-sLD8 SoC.
30
31config ARCH_UNIPHIER_PH1_PRO5
32	bool "UniPhier PH1-Pro5 SoC"
33	depends on !ARCH_UNIPHIER_PH1_SLD3 && \
34		   !ARCH_UNIPHIER_PH1_LD4 && \
35		   !ARCH_UNIPHIER_PH1_SLD8
36	help
37	  This enables support for UniPhier PH1-Pro5 SoC.
38
39config ARCH_UNIPHIER_PROXSTREAM2
40	bool "UniPhier ProXstream2 SoC"
41	depends on !ARCH_UNIPHIER_PH1_SLD3 && \
42		   !ARCH_UNIPHIER_PH1_LD4 && \
43		   !ARCH_UNIPHIER_PH1_SLD8
44	help
45	  This enables support for UniPhier ProXstream2 SoC.
46
47config ARCH_UNIPHIER_PH1_LD6B
48	bool "UniPhier PH1-LD6b SoC"
49	depends on !ARCH_UNIPHIER_PH1_SLD3 && \
50		   !ARCH_UNIPHIER_PH1_LD4 && \
51		   !ARCH_UNIPHIER_PH1_SLD8
52	help
53	  This enables support for UniPhier PH1-LD6b SoC.
54
55config MICRO_SUPPORT_CARD
56	bool "Use Micro Support Card"
57	help
58	  This option provides support for the expansion board, available
59	  on some UniPhier reference boards.
60
61	  Say Y to use the on-board UART, Ether, LED devices.
62
63config CMD_PINMON
64	bool "Enable boot mode pins monitor command"
65	default y
66	help
67	  The command "pinmon" shows the state of the boot mode pins.
68	  The boot mode pins are latched when the system reset is deasserted
69	  and determine which device the system should load a boot image from.
70
71config CMD_DDRPHY_DUMP
72	bool "Enable dump command of DDR PHY parameters"
73	depends on ARCH_UNIPHIER_PH1_LD4 || ARCH_UNIPHIER_PH1_PRO4 || \
74		   ARCH_UNIPHIER_PH1_SLD8
75	help
76	  The command "ddrphy" shows the resulting parameters of DDR PHY
77	  training; it is useful for the evaluation of DDR PHY training.
78
79config CMD_DDRMPHY_DUMP
80	bool "Enable dump command of DDR Multi PHY parameters"
81	depends on ARCH_UNIPHIER_PROXSTREAM2 || ARCH_UNIPHIER_PH1_LD6B
82	help
83	  The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
84	  training; it is useful for the evaluation of DDR Multi PHY training.
85
86endif
87