1 /* 2 * (C) Copyright 2011 3 * Marvell Semiconductor <www.marvell.com> 4 * Written-by: Lei Wen <leiwen@marvell.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 /* 10 * This file should be included in board config header file. 11 * 12 * It supports common definitions for MVEBU platforms 13 */ 14 15 #ifndef _MVEBU_CONFIG_H 16 #define _MVEBU_CONFIG_H 17 18 #include <asm/arch/soc.h> 19 20 #if defined(CONFIG_ARMADA_XP) || defined(CONFIG_ARMADA_375) \ 21 || defined(CONFIG_ARMADA_38X) 22 /* 23 * Set this for the common xor register definitions needed in dram.c 24 * for A38x as well here. 25 */ 26 #define MV88F78X60 /* for the DDR training bin_hdr code */ 27 #endif 28 29 #define CONFIG_SYS_CACHELINE_SIZE 32 30 31 #define CONFIG_SYS_L2_PL310 32 33 #ifdef CONFIG_SPL_BUILD 34 #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ 35 #endif 36 37 /* 38 * By default kwbimage.cfg from board specific folder is used 39 * If for some board, different configuration file need to be used, 40 * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file 41 */ 42 #ifndef CONFIG_SYS_KWD_CONFIG 43 #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg 44 #endif /* CONFIG_SYS_KWD_CONFIG */ 45 46 /* Add target to build it automatically upon "make" */ 47 #ifdef CONFIG_SPL 48 #define CONFIG_BUILD_TARGET "u-boot-spl.kwb" 49 #endif 50 51 /* end of 16M scrubbed by training in bootrom */ 52 #define CONFIG_SYS_INIT_SP_ADDR 0x00FF0000 53 #define CONFIG_NR_DRAM_BANKS_MAX 2 54 55 #define MV_UART_CONSOLE_BASE MVEBU_UART0_BASE 56 57 /* 58 * SPI Flash configuration 59 */ 60 #ifdef CONFIG_CMD_SF 61 #define CONFIG_KIRKWOOD_SPI 62 #ifndef CONFIG_ENV_SPI_BUS 63 # define CONFIG_ENV_SPI_BUS 0 64 #endif 65 #ifndef CONFIG_ENV_SPI_CS 66 # define CONFIG_ENV_SPI_CS 0 67 #endif 68 #ifndef CONFIG_ENV_SPI_MAX_HZ 69 # define CONFIG_ENV_SPI_MAX_HZ 50000000 70 #endif 71 #endif 72 73 /* Needed for SPI NOR booting in SPL */ 74 #define CONFIG_DM_SEQ_ALIAS 1 75 76 /* 77 * Ethernet Driver configuration 78 */ 79 #ifdef CONFIG_CMD_NET 80 #define CONFIG_MII /* expose smi ove miiphy interface */ 81 #if !defined(CONFIG_ARMADA_375) 82 #define CONFIG_MVNETA /* Enable Marvell Gbe Controller Driver */ 83 #define CONFIG_PHYLIB 84 #endif 85 #define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ 86 #define CONFIG_PHY_GIGE /* GbE speed/duplex detect */ 87 #define CONFIG_ARP_TIMEOUT 200 88 #define CONFIG_NET_RETRY_COUNT 50 89 #endif /* CONFIG_CMD_NET */ 90 91 /* 92 * I2C related stuff 93 */ 94 #ifdef CONFIG_CMD_I2C 95 #ifndef CONFIG_SYS_I2C_SOFT 96 #define CONFIG_I2C_MVTWSI 97 #endif 98 #define CONFIG_SYS_I2C_SLAVE 0x0 99 #define CONFIG_SYS_I2C_SPEED 100000 100 #endif 101 102 /* Use common timer */ 103 #define CONFIG_SYS_TIMER_COUNTS_DOWN 104 #define CONFIG_SYS_TIMER_COUNTER (MVEBU_TIMER_BASE + 0x14) 105 #define CONFIG_SYS_TIMER_RATE 25000000 106 107 #endif /* __MVEBU_CONFIG_H */ 108