1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3  * Copyright (C) 2016 Stefan Roese <sr@denx.de>
4  */
5 
6 #include <common.h>
7 #include <dm.h>
8 #include <fdtdec.h>
9 #include <linux/libfdt.h>
10 #include <linux/sizes.h>
11 #include <pci.h>
12 #include <asm/io.h>
13 #include <asm/system.h>
14 #include <asm/arch/cpu.h>
15 #include <asm/arch/soc.h>
16 #include <asm/armv8/mmu.h>
17 
18 DECLARE_GLOBAL_DATA_PTR;
19 
20 /*
21  * Not all memory is mapped in the MMU. So we need to restrict the
22  * memory size so that U-Boot does not try to access it. Also, the
23  * internal registers are located at 0xf000.0000 - 0xffff.ffff.
24  * Currently only 2GiB are mapped for system memory. This is what
25  * we pass to the U-Boot subsystem here.
26  */
27 #define USABLE_RAM_SIZE		0x80000000
28 
29 ulong board_get_usable_ram_top(ulong total_size)
30 {
31 	if (gd->ram_size > USABLE_RAM_SIZE)
32 		return USABLE_RAM_SIZE;
33 
34 	return gd->ram_size;
35 }
36 
37 /*
38  * On ARMv8, MBus is not configured in U-Boot. To enable compilation
39  * of the already implemented drivers, lets add a dummy version of
40  * this function so that linking does not fail.
41  */
42 const struct mbus_dram_target_info *mvebu_mbus_dram_info(void)
43 {
44 	return NULL;
45 }
46 
47 /* DRAM init code ... */
48 
49 #define MV_SIP_DRAM_SIZE	0x82000010
50 
51 static u64 a8k_dram_scan_ap_sz(void)
52 {
53 	struct pt_regs pregs;
54 
55 	pregs.regs[0] = MV_SIP_DRAM_SIZE;
56 	pregs.regs[1] = SOC_REGS_PHY_BASE;
57 	smc_call(&pregs);
58 
59 	return pregs.regs[0];
60 }
61 
62 static void a8k_dram_init_banksize(void)
63 {
64 	/*
65 	 * The firmware (ATF) leaves a 1G whole above the 3G mark for IO
66 	 * devices. Higher RAM is mapped at 4G.
67 	 *
68 	 * Config 2 DRAM banks:
69 	 * Bank 0 - max size 4G - 1G
70 	 * Bank 1 - ram size - 4G + 1G
71 	 */
72 	phys_size_t max_bank0_size = SZ_4G - SZ_1G;
73 
74 	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
75 	if (gd->ram_size <= max_bank0_size) {
76 		gd->bd->bi_dram[0].size = gd->ram_size;
77 		return;
78 	}
79 
80 	gd->bd->bi_dram[0].size = max_bank0_size;
81 	if (CONFIG_NR_DRAM_BANKS > 1) {
82 		gd->bd->bi_dram[1].start = SZ_4G;
83 		gd->bd->bi_dram[1].size = gd->ram_size - max_bank0_size;
84 	}
85 }
86 
87 __weak int dram_init_banksize(void)
88 {
89 	if (CONFIG_IS_ENABLED(ARMADA_8K))
90 		a8k_dram_init_banksize();
91 	else
92 		fdtdec_setup_memory_banksize();
93 
94 	return 0;
95 }
96 
97 __weak int dram_init(void)
98 {
99 	if (CONFIG_IS_ENABLED(ARMADA_8K)) {
100 		gd->ram_size = a8k_dram_scan_ap_sz();
101 		if (gd->ram_size != 0)
102 			return 0;
103 	}
104 
105 	if (fdtdec_setup_mem_size_base() != 0)
106 		return -EINVAL;
107 
108 	return 0;
109 }
110 
111 int arch_cpu_init(void)
112 {
113 	/* Nothing to do (yet) */
114 	return 0;
115 }
116 
117 int arch_early_init_r(void)
118 {
119 	struct udevice *dev;
120 	int ret;
121 	int i;
122 
123 	/*
124 	 * Loop over all MISC uclass drivers to call the comphy code
125 	 * and init all CP110 devices enabled in the DT
126 	 */
127 	i = 0;
128 	while (1) {
129 		/* Call the comphy code via the MISC uclass driver */
130 		ret = uclass_get_device(UCLASS_MISC, i++, &dev);
131 
132 		/* We're done, once no further CP110 device is found */
133 		if (ret)
134 			break;
135 	}
136 
137 	/* Cause the SATA device to do its early init */
138 	uclass_first_device(UCLASS_AHCI, &dev);
139 
140 #ifdef CONFIG_DM_PCI
141 	/* Trigger PCIe devices detection */
142 	pci_init();
143 #endif
144 
145 	return 0;
146 }
147