1 /*
2  * (C) Copyright 2011
3  * Marvell Semiconductor <www.marvell.com>
4  * Written-by: Lei Wen <leiwen@marvell.com>
5  *
6  * SPDX-License-Identifier:	GPL-2.0+
7  */
8 
9 /*
10  * This file should be included in board config header file.
11  *
12  * It supports common definitions for Kirkwood platform
13  */
14 
15 #ifndef _KW_CONFIG_H
16 #define _KW_CONFIG_H
17 
18 #if defined (CONFIG_KW88F6281)
19 #include <asm/arch/kw88f6281.h>
20 #elif defined (CONFIG_KW88F6192)
21 #include <asm/arch/kw88f6192.h>
22 #else
23 #error "SOC Name not defined"
24 #endif /* CONFIG_KW88F6281 */
25 
26 #include <asm/arch/soc.h>
27 #define CONFIG_SYS_CACHELINE_SIZE	32
28 				/* default Dcache Line length for kirkwood */
29 #define CONFIG_MD5	/* get_random_hex on krikwood needs MD5 support */
30 #define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
31 #define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
32 #define CONFIG_KIRKWOOD_PCIE_INIT       /* Enable PCIE Port0 for kernel */
33 
34 /*
35  * By default kwbimage.cfg from board specific folder is used
36  * If for some board, different configuration file need to be used,
37  * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
38  */
39 #ifndef CONFIG_SYS_KWD_CONFIG
40 #define	CONFIG_SYS_KWD_CONFIG	$(CONFIG_BOARDDIR)/kwbimage.cfg
41 #endif /* CONFIG_SYS_KWD_CONFIG */
42 
43 /* Kirkwood has 2k of Security SRAM, use it for SP */
44 #define CONFIG_SYS_INIT_SP_ADDR		0xC8012000
45 #define CONFIG_NR_DRAM_BANKS_MAX	2
46 
47 #define CONFIG_I2C_MVTWSI_BASE0	KW_TWSI_BASE
48 #define MV_UART_CONSOLE_BASE	KW_UART0_BASE
49 #define MV_SATA_BASE		KW_SATA_BASE
50 #define MV_SATA_PORT0_OFFSET	KW_SATA_PORT0_OFFSET
51 #define MV_SATA_PORT1_OFFSET	KW_SATA_PORT1_OFFSET
52 
53 /*
54  * NAND configuration
55  */
56 #ifdef CONFIG_CMD_NAND
57 #define CONFIG_NAND_KIRKWOOD
58 #define CONFIG_SYS_NAND_BASE		0xD8000000	/* MV_DEFADR_NANDF */
59 #define NAND_ALLOW_ERASE_ALL		1
60 #endif
61 
62 /*
63  * SPI Flash configuration
64  */
65 #ifdef CONFIG_CMD_SF
66 #define CONFIG_HARD_SPI			1
67 #define CONFIG_KIRKWOOD_SPI		1
68 #ifndef CONFIG_ENV_SPI_BUS
69 # define CONFIG_ENV_SPI_BUS		0
70 #endif
71 #ifndef CONFIG_ENV_SPI_CS
72 # define CONFIG_ENV_SPI_CS		0
73 #endif
74 #ifndef CONFIG_ENV_SPI_MAX_HZ
75 # define CONFIG_ENV_SPI_MAX_HZ		50000000
76 #endif
77 #endif
78 
79 /*
80  * Ethernet Driver configuration
81  */
82 #ifdef CONFIG_CMD_NET
83 #define CONFIG_CMD_MII
84 #define CONFIG_NETCONSOLE	/* include NetConsole support   */
85 #define CONFIG_MII		/* expose smi ove miiphy interface */
86 #define CONFIG_MVGBE		/* Enable Marvell Gbe Controller Driver */
87 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
88 #define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
89 #define CONFIG_RESET_PHY_R	/* use reset_phy() to init mv8831116 PHY */
90 #endif /* CONFIG_CMD_NET */
91 
92 /*
93  * USB/EHCI
94  */
95 #ifdef CONFIG_CMD_USB
96 #define CONFIG_USB_EHCI_MARVELL
97 #define CONFIG_EHCI_IS_TDI
98 #endif /* CONFIG_CMD_USB */
99 
100 /*
101  * IDE Support on SATA ports
102  */
103 #ifdef CONFIG_CMD_IDE
104 #define __io
105 #define CONFIG_CMD_EXT2
106 #define CONFIG_MVSATA_IDE
107 #define CONFIG_IDE_PREINIT
108 #define CONFIG_MVSATA_IDE_USE_PORT1
109 /* Needs byte-swapping for ATA data register */
110 #define CONFIG_IDE_SWAP_IO
111 /* Data, registers and alternate blocks are at the same offset */
112 #define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
113 #define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
114 #define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
115 /* Each 8-bit ATA register is aligned to a 4-bytes address */
116 #define CONFIG_SYS_ATA_STRIDE		4
117 /* Controller supports 48-bits LBA addressing */
118 #define CONFIG_LBA48
119 /* CONFIG_CMD_IDE requires some #defines for ATA registers */
120 #define CONFIG_SYS_IDE_MAXBUS		2
121 #define CONFIG_SYS_IDE_MAXDEVICE	2
122 /* ATA registers base is at SATA controller base */
123 #define CONFIG_SYS_ATA_BASE_ADDR	MV_SATA_BASE
124 #endif /* CONFIG_CMD_IDE */
125 
126 /*
127  * I2C related stuff
128  */
129 #ifdef CONFIG_CMD_I2C
130 #ifndef CONFIG_SYS_I2C_SOFT
131 #define CONFIG_SYS_I2C
132 #define CONFIG_SYS_I2C_MVTWSI
133 #endif
134 #define CONFIG_SYS_I2C_SLAVE		0x0
135 #define CONFIG_SYS_I2C_SPEED		100000
136 #endif
137 
138 #endif /* _KW_CONFIG_H */
139