1 /* 2 * (C) Copyright 2009 3 * Marvell Semiconductor <www.marvell.com> 4 * Written-by: Prafulla Wadaskar <prafulla@marvell.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <common.h> 10 #include <netdev.h> 11 #include <asm/cache.h> 12 #include <asm/io.h> 13 #include <asm/arch/cpu.h> 14 #include <asm/arch/soc.h> 15 #include <mvebu_mmc.h> 16 17 void reset_cpu(unsigned long ignored) 18 { 19 struct kwcpu_registers *cpureg = 20 (struct kwcpu_registers *)KW_CPU_REG_BASE; 21 22 writel(readl(&cpureg->rstoutn_mask) | (1 << 2), 23 &cpureg->rstoutn_mask); 24 writel(readl(&cpureg->sys_soft_rst) | 1, 25 &cpureg->sys_soft_rst); 26 while (1) ; 27 } 28 29 /* 30 * Window Size 31 * Used with the Base register to set the address window size and location. 32 * Must be programmed from LSB to MSB as sequence of ones followed by 33 * sequence of zeros. The number of ones specifies the size of the window in 34 * 64 KByte granularity (e.g., a value of 0x00FF specifies 256 = 16 MByte). 35 * NOTE: A value of 0x0 specifies 64-KByte size. 36 */ 37 unsigned int kw_winctrl_calcsize(unsigned int sizeval) 38 { 39 int i; 40 unsigned int j = 0; 41 u32 val = sizeval >> 1; 42 43 for (i = 0; val >= 0x10000; i++) { 44 j |= (1 << i); 45 val = val >> 1; 46 } 47 return (0x0000ffff & j); 48 } 49 50 /* 51 * kw_config_adr_windows - Configure address Windows 52 * 53 * There are 8 address windows supported by Kirkwood Soc to addess different 54 * devices. Each window can be configured for size, BAR and remap addr 55 * Below configuration is standard for most of the cases 56 * 57 * If remap function not used, remap_lo must be set as base 58 * 59 * Reference Documentation: 60 * Mbus-L to Mbus Bridge Registers Configuration. 61 * (Sec 25.1 and 25.3 of Datasheet) 62 */ 63 int kw_config_adr_windows(void) 64 { 65 struct kwwin_registers *winregs = 66 (struct kwwin_registers *)KW_CPU_WIN_BASE; 67 68 /* Window 0: PCIE MEM address space */ 69 writel(KWCPU_WIN_CTRL_DATA(1024 * 1024 * 256, KWCPU_TARGET_PCIE, 70 KWCPU_ATTR_PCIE_MEM, KWCPU_WIN_ENABLE), &winregs[0].ctrl); 71 72 writel(KW_DEFADR_PCI_MEM, &winregs[0].base); 73 writel(KW_DEFADR_PCI_MEM, &winregs[0].remap_lo); 74 writel(0x0, &winregs[0].remap_hi); 75 76 /* Window 1: PCIE IO address space */ 77 writel(KWCPU_WIN_CTRL_DATA(1024 * 64, KWCPU_TARGET_PCIE, 78 KWCPU_ATTR_PCIE_IO, KWCPU_WIN_ENABLE), &winregs[1].ctrl); 79 writel(KW_DEFADR_PCI_IO, &winregs[1].base); 80 writel(KW_DEFADR_PCI_IO_REMAP, &winregs[1].remap_lo); 81 writel(0x0, &winregs[1].remap_hi); 82 83 /* Window 2: NAND Flash address space */ 84 writel(KWCPU_WIN_CTRL_DATA(1024 * 1024 * 128, KWCPU_TARGET_MEMORY, 85 KWCPU_ATTR_NANDFLASH, KWCPU_WIN_ENABLE), &winregs[2].ctrl); 86 writel(KW_DEFADR_NANDF, &winregs[2].base); 87 writel(KW_DEFADR_NANDF, &winregs[2].remap_lo); 88 writel(0x0, &winregs[2].remap_hi); 89 90 /* Window 3: SPI Flash address space */ 91 writel(KWCPU_WIN_CTRL_DATA(1024 * 1024 * 128, KWCPU_TARGET_MEMORY, 92 KWCPU_ATTR_SPIFLASH, KWCPU_WIN_ENABLE), &winregs[3].ctrl); 93 writel(KW_DEFADR_SPIF, &winregs[3].base); 94 writel(KW_DEFADR_SPIF, &winregs[3].remap_lo); 95 writel(0x0, &winregs[3].remap_hi); 96 97 /* Window 4: BOOT Memory address space */ 98 writel(KWCPU_WIN_CTRL_DATA(1024 * 1024 * 128, KWCPU_TARGET_MEMORY, 99 KWCPU_ATTR_BOOTROM, KWCPU_WIN_ENABLE), &winregs[4].ctrl); 100 writel(KW_DEFADR_BOOTROM, &winregs[4].base); 101 102 /* Window 5: Security SRAM address space */ 103 writel(KWCPU_WIN_CTRL_DATA(1024 * 64, KWCPU_TARGET_SASRAM, 104 KWCPU_ATTR_SASRAM, KWCPU_WIN_ENABLE), &winregs[5].ctrl); 105 writel(KW_DEFADR_SASRAM, &winregs[5].base); 106 107 /* Window 6-7: Disabled */ 108 writel(KWCPU_WIN_DISABLE, &winregs[6].ctrl); 109 writel(KWCPU_WIN_DISABLE, &winregs[7].ctrl); 110 111 return 0; 112 } 113 114 /* 115 * SYSRSTn Duration Counter Support 116 * 117 * Kirkwood SoC implements a hardware-based SYSRSTn duration counter. 118 * When SYSRSTn is asserted low, a SYSRSTn duration counter is running. 119 * The SYSRSTn duration counter is useful for implementing a manufacturer 120 * or factory reset. Upon a long reset assertion that is greater than a 121 * pre-configured environment variable value for sysrstdelay, 122 * The counter value is stored in the SYSRSTn Length Counter Register 123 * The counter is based on the 25-MHz reference clock (40ns) 124 * It is a 29-bit counter, yielding a maximum counting duration of 125 * 2^29/25 MHz (21.4 seconds). When the counter reach its maximum value, 126 * it remains at this value until counter reset is triggered by setting 127 * bit 31 of KW_REG_SYSRST_CNT 128 */ 129 static void kw_sysrst_action(void) 130 { 131 int ret; 132 char *s = env_get("sysrstcmd"); 133 134 if (!s) { 135 debug("Error.. %s failed, check sysrstcmd\n", 136 __FUNCTION__); 137 return; 138 } 139 140 debug("Starting %s process...\n", __FUNCTION__); 141 ret = run_command(s, 0); 142 if (ret != 0) 143 debug("Error.. %s failed\n", __FUNCTION__); 144 else 145 debug("%s process finished\n", __FUNCTION__); 146 } 147 148 static void kw_sysrst_check(void) 149 { 150 u32 sysrst_cnt, sysrst_dly; 151 char *s; 152 153 /* 154 * no action if sysrstdelay environment variable is not defined 155 */ 156 s = env_get("sysrstdelay"); 157 if (s == NULL) 158 return; 159 160 /* read sysrstdelay value */ 161 sysrst_dly = (u32) simple_strtoul(s, NULL, 10); 162 163 /* read SysRst Length counter register (bits 28:0) */ 164 sysrst_cnt = (0x1fffffff & readl(KW_REG_SYSRST_CNT)); 165 debug("H/w Rst hold time: %d.%d secs\n", 166 sysrst_cnt / SYSRST_CNT_1SEC_VAL, 167 sysrst_cnt % SYSRST_CNT_1SEC_VAL); 168 169 /* clear the counter for next valid read*/ 170 writel(1 << 31, KW_REG_SYSRST_CNT); 171 172 /* 173 * sysrst_action: 174 * if H/w Reset key is pressed and hold for time 175 * more than sysrst_dly in seconds 176 */ 177 if (sysrst_cnt >= SYSRST_CNT_1SEC_VAL * sysrst_dly) 178 kw_sysrst_action(); 179 } 180 181 #if defined(CONFIG_DISPLAY_CPUINFO) 182 int print_cpuinfo(void) 183 { 184 char *rev = "??"; 185 u16 devid = (readl(KW_REG_PCIE_DEVID) >> 16) & 0xffff; 186 u8 revid = readl(KW_REG_PCIE_REVID) & 0xff; 187 188 if ((readl(KW_REG_DEVICE_ID) & 0x03) > 2) { 189 printf("Error.. %s:Unsupported Kirkwood SoC 88F%04x\n", __FUNCTION__, devid); 190 return -1; 191 } 192 193 switch (revid) { 194 case 0: 195 if (devid == 0x6281) 196 rev = "Z0"; 197 else if (devid == 0x6282) 198 rev = "A0"; 199 break; 200 case 1: 201 rev = "A1"; 202 break; 203 case 2: 204 rev = "A0"; 205 break; 206 case 3: 207 rev = "A1"; 208 break; 209 default: 210 break; 211 } 212 213 printf("SoC: Kirkwood 88F%04x_%s\n", devid, rev); 214 return 0; 215 } 216 #endif /* CONFIG_DISPLAY_CPUINFO */ 217 218 #ifdef CONFIG_ARCH_CPU_INIT 219 int arch_cpu_init(void) 220 { 221 u32 reg; 222 struct kwcpu_registers *cpureg = 223 (struct kwcpu_registers *)KW_CPU_REG_BASE; 224 225 /* Linux expects` the internal registers to be at 0xf1000000 */ 226 writel(KW_REGS_PHY_BASE, KW_OFFSET_REG); 227 228 /* Enable and invalidate L2 cache in write through mode */ 229 writel(readl(&cpureg->l2_cfg) | 0x18, &cpureg->l2_cfg); 230 invalidate_l2_cache(); 231 232 kw_config_adr_windows(); 233 234 #ifdef CONFIG_KIRKWOOD_RGMII_PAD_1V8 235 /* 236 * Configures the I/O voltage of the pads connected to Egigabit 237 * Ethernet interface to 1.8V 238 * By default it is set to 3.3V 239 */ 240 reg = readl(KW_REG_MPP_OUT_DRV_REG); 241 reg |= (1 << 7); 242 writel(reg, KW_REG_MPP_OUT_DRV_REG); 243 #endif 244 #ifdef CONFIG_KIRKWOOD_EGIGA_INIT 245 /* 246 * Set egiga port0/1 in normal functional mode 247 * This is required becasue on kirkwood by default ports are in reset mode 248 * OS egiga driver may not have provision to set them in normal mode 249 * and if u-boot is build without network support, network may fail at OS level 250 */ 251 reg = readl(KWGBE_PORT_SERIAL_CONTROL1_REG(0)); 252 reg &= ~(1 << 4); /* Clear PortReset Bit */ 253 writel(reg, (KWGBE_PORT_SERIAL_CONTROL1_REG(0))); 254 reg = readl(KWGBE_PORT_SERIAL_CONTROL1_REG(1)); 255 reg &= ~(1 << 4); /* Clear PortReset Bit */ 256 writel(reg, (KWGBE_PORT_SERIAL_CONTROL1_REG(1))); 257 #endif 258 #ifdef CONFIG_KIRKWOOD_PCIE_INIT 259 /* 260 * Enable PCI Express Port0 261 */ 262 reg = readl(&cpureg->ctrl_stat); 263 reg |= (1 << 0); /* Set PEX0En Bit */ 264 writel(reg, &cpureg->ctrl_stat); 265 #endif 266 return 0; 267 } 268 #endif /* CONFIG_ARCH_CPU_INIT */ 269 270 /* 271 * SOC specific misc init 272 */ 273 #if defined(CONFIG_ARCH_MISC_INIT) 274 int arch_misc_init(void) 275 { 276 volatile u32 temp; 277 278 /*CPU streaming & write allocate */ 279 temp = readfr_extra_feature_reg(); 280 temp &= ~(1 << 28); /* disable wr alloc */ 281 writefr_extra_feature_reg(temp); 282 283 temp = readfr_extra_feature_reg(); 284 temp &= ~(1 << 29); /* streaming disabled */ 285 writefr_extra_feature_reg(temp); 286 287 /* L2Cache settings */ 288 temp = readfr_extra_feature_reg(); 289 /* Disable L2C pre fetch - Set bit 24 */ 290 temp |= (1 << 24); 291 /* enable L2C - Set bit 22 */ 292 temp |= (1 << 22); 293 writefr_extra_feature_reg(temp); 294 295 icache_enable(); 296 /* Change reset vector to address 0x0 */ 297 temp = get_cr(); 298 set_cr(temp & ~CR_V); 299 300 /* checks and execute resset to factory event */ 301 kw_sysrst_check(); 302 303 return 0; 304 } 305 #endif /* CONFIG_ARCH_MISC_INIT */ 306 307 #ifdef CONFIG_MVGBE 308 int cpu_eth_init(bd_t *bis) 309 { 310 mvgbe_initialize(bis); 311 return 0; 312 } 313 #endif 314 315 #ifdef CONFIG_MVEBU_MMC 316 int board_mmc_init(bd_t *bis) 317 { 318 mvebu_mmc_init(bis); 319 return 0; 320 } 321 #endif /* CONFIG_MVEBU_MMC */ 322