1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * (C) Copyright 2007 4 * Sascha Hauer, Pengutronix 5 * 6 * (C) Copyright 2009 Freescale Semiconductor, Inc. 7 */ 8 9 #include <common.h> 10 #include <linux/errno.h> 11 #include <asm/io.h> 12 #include <asm/arch/imx-regs.h> 13 #include <asm/arch/clock.h> 14 #include <asm/arch/sys_proto.h> 15 #include <asm/bootm.h> 16 #include <asm/mach-imx/boot_mode.h> 17 #include <asm/mach-imx/dma.h> 18 #include <asm/mach-imx/hab.h> 19 #include <stdbool.h> 20 #include <asm/arch/mxc_hdmi.h> 21 #include <asm/arch/crm_regs.h> 22 #include <dm.h> 23 #include <imx_thermal.h> 24 #include <mmc.h> 25 26 enum ldo_reg { 27 LDO_ARM, 28 LDO_SOC, 29 LDO_PU, 30 }; 31 32 struct scu_regs { 33 u32 ctrl; 34 u32 config; 35 u32 status; 36 u32 invalidate; 37 u32 fpga_rev; 38 }; 39 40 #if defined(CONFIG_IMX_THERMAL) 41 static const struct imx_thermal_plat imx6_thermal_plat = { 42 .regs = (void *)ANATOP_BASE_ADDR, 43 .fuse_bank = 1, 44 .fuse_word = 6, 45 }; 46 47 U_BOOT_DEVICE(imx6_thermal) = { 48 .name = "imx_thermal", 49 .platdata = &imx6_thermal_plat, 50 }; 51 #endif 52 53 #if defined(CONFIG_SECURE_BOOT) 54 struct imx_sec_config_fuse_t const imx_sec_config_fuse = { 55 .bank = 0, 56 .word = 6, 57 }; 58 #endif 59 60 u32 get_nr_cpus(void) 61 { 62 struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR; 63 return readl(&scu->config) & 3; 64 } 65 66 u32 get_cpu_rev(void) 67 { 68 struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; 69 u32 reg = readl(&anatop->digprog_sololite); 70 u32 type = ((reg >> 16) & 0xff); 71 u32 major, cfg = 0; 72 73 if (type != MXC_CPU_MX6SL) { 74 reg = readl(&anatop->digprog); 75 struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR; 76 cfg = readl(&scu->config) & 3; 77 type = ((reg >> 16) & 0xff); 78 if (type == MXC_CPU_MX6DL) { 79 if (!cfg) 80 type = MXC_CPU_MX6SOLO; 81 } 82 83 if (type == MXC_CPU_MX6Q) { 84 if (cfg == 1) 85 type = MXC_CPU_MX6D; 86 } 87 88 } 89 major = ((reg >> 8) & 0xff); 90 if ((major >= 1) && 91 ((type == MXC_CPU_MX6Q) || (type == MXC_CPU_MX6D))) { 92 major--; 93 type = MXC_CPU_MX6QP; 94 if (cfg == 1) 95 type = MXC_CPU_MX6DP; 96 } 97 reg &= 0xff; /* mx6 silicon revision */ 98 return (type << 12) | (reg + (0x10 * (major + 1))); 99 } 100 101 /* 102 * OCOTP_CFG3[17:16] (see Fusemap Description Table offset 0x440) 103 * defines a 2-bit SPEED_GRADING 104 */ 105 #define OCOTP_CFG3_SPEED_SHIFT 16 106 #define OCOTP_CFG3_SPEED_800MHZ 0 107 #define OCOTP_CFG3_SPEED_850MHZ 1 108 #define OCOTP_CFG3_SPEED_1GHZ 2 109 #define OCOTP_CFG3_SPEED_1P2GHZ 3 110 111 /* 112 * For i.MX6UL 113 */ 114 #define OCOTP_CFG3_SPEED_528MHZ 1 115 #define OCOTP_CFG3_SPEED_696MHZ 2 116 117 /* 118 * For i.MX6ULL 119 */ 120 #define OCOTP_CFG3_SPEED_792MHZ 2 121 #define OCOTP_CFG3_SPEED_900MHZ 3 122 123 u32 get_cpu_speed_grade_hz(void) 124 { 125 struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR; 126 struct fuse_bank *bank = &ocotp->bank[0]; 127 struct fuse_bank0_regs *fuse = 128 (struct fuse_bank0_regs *)bank->fuse_regs; 129 uint32_t val; 130 131 val = readl(&fuse->cfg3); 132 val >>= OCOTP_CFG3_SPEED_SHIFT; 133 val &= 0x3; 134 135 if (is_mx6ul()) { 136 if (val == OCOTP_CFG3_SPEED_528MHZ) 137 return 528000000; 138 else if (val == OCOTP_CFG3_SPEED_696MHZ) 139 return 696000000; 140 else 141 return 0; 142 } 143 144 if (is_mx6ull()) { 145 if (val == OCOTP_CFG3_SPEED_528MHZ) 146 return 528000000; 147 else if (val == OCOTP_CFG3_SPEED_792MHZ) 148 return 792000000; 149 else if (val == OCOTP_CFG3_SPEED_900MHZ) 150 return 900000000; 151 else 152 return 0; 153 } 154 155 switch (val) { 156 /* Valid for IMX6DQ */ 157 case OCOTP_CFG3_SPEED_1P2GHZ: 158 if (is_mx6dq() || is_mx6dqp()) 159 return 1200000000; 160 /* Valid for IMX6SX/IMX6SDL/IMX6DQ */ 161 case OCOTP_CFG3_SPEED_1GHZ: 162 return 996000000; 163 /* Valid for IMX6DQ */ 164 case OCOTP_CFG3_SPEED_850MHZ: 165 if (is_mx6dq() || is_mx6dqp()) 166 return 852000000; 167 /* Valid for IMX6SX/IMX6SDL/IMX6DQ */ 168 case OCOTP_CFG3_SPEED_800MHZ: 169 return 792000000; 170 } 171 return 0; 172 } 173 174 /* 175 * OCOTP_MEM0[7:6] (see Fusemap Description Table offset 0x480) 176 * defines a 2-bit Temperature Grade 177 * 178 * return temperature grade and min/max temperature in Celsius 179 */ 180 #define OCOTP_MEM0_TEMP_SHIFT 6 181 182 u32 get_cpu_temp_grade(int *minc, int *maxc) 183 { 184 struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR; 185 struct fuse_bank *bank = &ocotp->bank[1]; 186 struct fuse_bank1_regs *fuse = 187 (struct fuse_bank1_regs *)bank->fuse_regs; 188 uint32_t val; 189 190 val = readl(&fuse->mem0); 191 val >>= OCOTP_MEM0_TEMP_SHIFT; 192 val &= 0x3; 193 194 if (minc && maxc) { 195 if (val == TEMP_AUTOMOTIVE) { 196 *minc = -40; 197 *maxc = 125; 198 } else if (val == TEMP_INDUSTRIAL) { 199 *minc = -40; 200 *maxc = 105; 201 } else if (val == TEMP_EXTCOMMERCIAL) { 202 *minc = -20; 203 *maxc = 105; 204 } else { 205 *minc = 0; 206 *maxc = 95; 207 } 208 } 209 return val; 210 } 211 212 #ifdef CONFIG_REVISION_TAG 213 u32 __weak get_board_rev(void) 214 { 215 u32 cpurev = get_cpu_rev(); 216 u32 type = ((cpurev >> 12) & 0xff); 217 if (type == MXC_CPU_MX6SOLO) 218 cpurev = (MXC_CPU_MX6DL) << 12 | (cpurev & 0xFFF); 219 220 if (type == MXC_CPU_MX6D) 221 cpurev = (MXC_CPU_MX6Q) << 12 | (cpurev & 0xFFF); 222 223 return cpurev; 224 } 225 #endif 226 227 static void clear_ldo_ramp(void) 228 { 229 struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; 230 int reg; 231 232 /* ROM may modify LDO ramp up time according to fuse setting, so in 233 * order to be in the safe side we neeed to reset these settings to 234 * match the reset value: 0'b00 235 */ 236 reg = readl(&anatop->ana_misc2); 237 reg &= ~(0x3f << 24); 238 writel(reg, &anatop->ana_misc2); 239 } 240 241 /* 242 * Set the PMU_REG_CORE register 243 * 244 * Set LDO_SOC/PU/ARM regulators to the specified millivolt level. 245 * Possible values are from 0.725V to 1.450V in steps of 246 * 0.025V (25mV). 247 */ 248 static int set_ldo_voltage(enum ldo_reg ldo, u32 mv) 249 { 250 struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; 251 u32 val, step, old, reg = readl(&anatop->reg_core); 252 u8 shift; 253 254 /* No LDO_SOC/PU/ARM */ 255 if (is_mx6sll()) 256 return 0; 257 258 if (mv < 725) 259 val = 0x00; /* Power gated off */ 260 else if (mv > 1450) 261 val = 0x1F; /* Power FET switched full on. No regulation */ 262 else 263 val = (mv - 700) / 25; 264 265 clear_ldo_ramp(); 266 267 switch (ldo) { 268 case LDO_SOC: 269 shift = 18; 270 break; 271 case LDO_PU: 272 shift = 9; 273 break; 274 case LDO_ARM: 275 shift = 0; 276 break; 277 default: 278 return -EINVAL; 279 } 280 281 old = (reg & (0x1F << shift)) >> shift; 282 step = abs(val - old); 283 if (step == 0) 284 return 0; 285 286 reg = (reg & ~(0x1F << shift)) | (val << shift); 287 writel(reg, &anatop->reg_core); 288 289 /* 290 * The LDO ramp-up is based on 64 clock cycles of 24 MHz = 2.6 us per 291 * step 292 */ 293 udelay(3 * step); 294 295 return 0; 296 } 297 298 static void set_ahb_rate(u32 val) 299 { 300 struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 301 u32 reg, div; 302 303 div = get_periph_clk() / val - 1; 304 reg = readl(&mxc_ccm->cbcdr); 305 306 writel((reg & (~MXC_CCM_CBCDR_AHB_PODF_MASK)) | 307 (div << MXC_CCM_CBCDR_AHB_PODF_OFFSET), &mxc_ccm->cbcdr); 308 } 309 310 static void clear_mmdc_ch_mask(void) 311 { 312 struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 313 u32 reg; 314 reg = readl(&mxc_ccm->ccdr); 315 316 /* Clear MMDC channel mask */ 317 if (is_mx6sx() || is_mx6ul() || is_mx6ull() || is_mx6sl() || is_mx6sll()) 318 reg &= ~(MXC_CCM_CCDR_MMDC_CH1_HS_MASK); 319 else 320 reg &= ~(MXC_CCM_CCDR_MMDC_CH1_HS_MASK | MXC_CCM_CCDR_MMDC_CH0_HS_MASK); 321 writel(reg, &mxc_ccm->ccdr); 322 } 323 324 #define OCOTP_MEM0_REFTOP_TRIM_SHIFT 8 325 326 static void init_bandgap(void) 327 { 328 struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; 329 struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR; 330 struct fuse_bank *bank = &ocotp->bank[1]; 331 struct fuse_bank1_regs *fuse = 332 (struct fuse_bank1_regs *)bank->fuse_regs; 333 uint32_t val; 334 335 /* 336 * Ensure the bandgap has stabilized. 337 */ 338 while (!(readl(&anatop->ana_misc0) & 0x80)) 339 ; 340 /* 341 * For best noise performance of the analog blocks using the 342 * outputs of the bandgap, the reftop_selfbiasoff bit should 343 * be set. 344 */ 345 writel(BM_ANADIG_ANA_MISC0_REFTOP_SELBIASOFF, &anatop->ana_misc0_set); 346 /* 347 * On i.MX6ULL,we need to set VBGADJ bits according to the 348 * REFTOP_TRIM[3:0] in fuse table 349 * 000 - set REFTOP_VBGADJ[2:0] to 3b'110, 350 * 110 - set REFTOP_VBGADJ[2:0] to 3b'000, 351 * 001 - set REFTOP_VBGADJ[2:0] to 3b'001, 352 * 010 - set REFTOP_VBGADJ[2:0] to 3b'010, 353 * 011 - set REFTOP_VBGADJ[2:0] to 3b'011, 354 * 100 - set REFTOP_VBGADJ[2:0] to 3b'100, 355 * 101 - set REFTOP_VBGADJ[2:0] to 3b'101, 356 * 111 - set REFTOP_VBGADJ[2:0] to 3b'111, 357 */ 358 if (is_mx6ull()) { 359 val = readl(&fuse->mem0); 360 val >>= OCOTP_MEM0_REFTOP_TRIM_SHIFT; 361 val &= 0x7; 362 363 writel(val << BM_ANADIG_ANA_MISC0_REFTOP_VBGADJ_SHIFT, 364 &anatop->ana_misc0_set); 365 } 366 } 367 368 int arch_cpu_init(void) 369 { 370 struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 371 372 init_aips(); 373 374 /* Need to clear MMDC_CHx_MASK to make warm reset work. */ 375 clear_mmdc_ch_mask(); 376 377 /* 378 * Disable self-bias circuit in the analog bandap. 379 * The self-bias circuit is used by the bandgap during startup. 380 * This bit should be set after the bandgap has initialized. 381 */ 382 init_bandgap(); 383 384 if (!is_mx6ul() && !is_mx6ull()) { 385 /* 386 * When low freq boot is enabled, ROM will not set AHB 387 * freq, so we need to ensure AHB freq is 132MHz in such 388 * scenario. 389 * 390 * To i.MX6UL, when power up, default ARM core and 391 * AHB rate is 396M and 132M. 392 */ 393 if (mxc_get_clock(MXC_ARM_CLK) == 396000000) 394 set_ahb_rate(132000000); 395 } 396 397 if (is_mx6ul()) { 398 if (is_soc_rev(CHIP_REV_1_0) == 0) { 399 /* 400 * According to the design team's requirement on 401 * i.MX6UL,the PMIC_STBY_REQ PAD should be configured 402 * as open drain 100K (0x0000b8a0). 403 * Only exists on TO1.0 404 */ 405 writel(0x0000b8a0, IOMUXC_BASE_ADDR + 0x29c); 406 } else { 407 /* 408 * From TO1.1, SNVS adds internal pull up control 409 * for POR_B, the register filed is GPBIT[1:0], 410 * after system boot up, it can be set to 2b'01 411 * to disable internal pull up.It can save about 412 * 30uA power in SNVS mode. 413 */ 414 writel((readl(MX6UL_SNVS_LP_BASE_ADDR + 0x10) & 415 (~0x1400)) | 0x400, 416 MX6UL_SNVS_LP_BASE_ADDR + 0x10); 417 } 418 } 419 420 if (is_mx6ull()) { 421 /* 422 * GPBIT[1:0] is suggested to set to 2'b11: 423 * 2'b00 : always PUP100K 424 * 2'b01 : PUP100K when PMIC_ON_REQ or SOC_NOT_FAIL 425 * 2'b10 : always disable PUP100K 426 * 2'b11 : PDN100K when SOC_FAIL, PUP100K when SOC_NOT_FAIL 427 * register offset is different from i.MX6UL, since 428 * i.MX6UL is fixed by ECO. 429 */ 430 writel(readl(MX6UL_SNVS_LP_BASE_ADDR) | 431 0x3, MX6UL_SNVS_LP_BASE_ADDR); 432 } 433 434 /* Set perclk to source from OSC 24MHz */ 435 if (is_mx6sl()) 436 setbits_le32(&ccm->cscmr1, MXC_CCM_CSCMR1_PER_CLK_SEL_MASK); 437 438 imx_wdog_disable_powerdown(); /* Disable PDE bit of WMCR register */ 439 440 if (is_mx6sx()) 441 setbits_le32(&ccm->cscdr1, MXC_CCM_CSCDR1_UART_CLK_SEL); 442 443 init_src(); 444 445 return 0; 446 } 447 448 #ifdef CONFIG_ENV_IS_IN_MMC 449 __weak int board_mmc_get_env_dev(int devno) 450 { 451 return CONFIG_SYS_MMC_ENV_DEV; 452 } 453 454 static int mmc_get_boot_dev(void) 455 { 456 struct src *src_regs = (struct src *)SRC_BASE_ADDR; 457 u32 soc_sbmr = readl(&src_regs->sbmr1); 458 u32 bootsel; 459 int devno; 460 461 /* 462 * Refer to 463 * "i.MX 6Dual/6Quad Applications Processor Reference Manual" 464 * Chapter "8.5.3.1 Expansion Device eFUSE Configuration" 465 * i.MX6SL/SX/UL has same layout. 466 */ 467 bootsel = (soc_sbmr & 0x000000FF) >> 6; 468 469 /* No boot from sd/mmc */ 470 if (bootsel != 1) 471 return -1; 472 473 /* BOOT_CFG2[3] and BOOT_CFG2[4] */ 474 devno = (soc_sbmr & 0x00001800) >> 11; 475 476 return devno; 477 } 478 479 int mmc_get_env_dev(void) 480 { 481 int devno = mmc_get_boot_dev(); 482 483 /* If not boot from sd/mmc, use default value */ 484 if (devno < 0) 485 return CONFIG_SYS_MMC_ENV_DEV; 486 487 return board_mmc_get_env_dev(devno); 488 } 489 490 #ifdef CONFIG_SYS_MMC_ENV_PART 491 __weak int board_mmc_get_env_part(int devno) 492 { 493 return CONFIG_SYS_MMC_ENV_PART; 494 } 495 496 uint mmc_get_env_part(struct mmc *mmc) 497 { 498 int devno = mmc_get_boot_dev(); 499 500 /* If not boot from sd/mmc, use default value */ 501 if (devno < 0) 502 return CONFIG_SYS_MMC_ENV_PART; 503 504 return board_mmc_get_env_part(devno); 505 } 506 #endif 507 #endif 508 509 int board_postclk_init(void) 510 { 511 /* NO LDO SOC on i.MX6SLL */ 512 if (is_mx6sll()) 513 return 0; 514 515 set_ldo_voltage(LDO_SOC, 1175); /* Set VDDSOC to 1.175V */ 516 517 return 0; 518 } 519 520 #ifndef CONFIG_SPL_BUILD 521 /* 522 * cfg_val will be used for 523 * Boot_cfg4[7:0]:Boot_cfg3[7:0]:Boot_cfg2[7:0]:Boot_cfg1[7:0] 524 * After reset, if GPR10[28] is 1, ROM will use GPR9[25:0] 525 * instead of SBMR1 to determine the boot device. 526 */ 527 const struct boot_mode soc_boot_modes[] = { 528 {"normal", MAKE_CFGVAL(0x00, 0x00, 0x00, 0x00)}, 529 /* reserved value should start rom usb */ 530 #if defined(CONFIG_MX6UL) || defined(CONFIG_MX6ULL) 531 {"usb", MAKE_CFGVAL(0x20, 0x00, 0x00, 0x00)}, 532 #else 533 {"usb", MAKE_CFGVAL(0x10, 0x00, 0x00, 0x00)}, 534 #endif 535 {"sata", MAKE_CFGVAL(0x20, 0x00, 0x00, 0x00)}, 536 {"ecspi1:0", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x08)}, 537 {"ecspi1:1", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x18)}, 538 {"ecspi1:2", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x28)}, 539 {"ecspi1:3", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x38)}, 540 /* 4 bit bus width */ 541 {"esdhc1", MAKE_CFGVAL(0x40, 0x20, 0x00, 0x00)}, 542 {"esdhc2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)}, 543 {"esdhc3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)}, 544 {"esdhc4", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)}, 545 {NULL, 0}, 546 }; 547 #endif 548 549 void reset_misc(void) 550 { 551 #ifdef CONFIG_VIDEO_MXS 552 lcdif_power_down(); 553 #endif 554 } 555 556 void s_init(void) 557 { 558 struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; 559 struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 560 u32 mask480; 561 u32 mask528; 562 u32 reg, periph1, periph2; 563 564 if (is_mx6sx() || is_mx6ul() || is_mx6ull() || is_mx6sll()) 565 return; 566 567 /* Due to hardware limitation, on MX6Q we need to gate/ungate all PFDs 568 * to make sure PFD is working right, otherwise, PFDs may 569 * not output clock after reset, MX6DL and MX6SL have added 396M pfd 570 * workaround in ROM code, as bus clock need it 571 */ 572 573 mask480 = ANATOP_PFD_CLKGATE_MASK(0) | 574 ANATOP_PFD_CLKGATE_MASK(1) | 575 ANATOP_PFD_CLKGATE_MASK(2) | 576 ANATOP_PFD_CLKGATE_MASK(3); 577 mask528 = ANATOP_PFD_CLKGATE_MASK(1) | 578 ANATOP_PFD_CLKGATE_MASK(3); 579 580 reg = readl(&ccm->cbcmr); 581 periph2 = ((reg & MXC_CCM_CBCMR_PRE_PERIPH2_CLK_SEL_MASK) 582 >> MXC_CCM_CBCMR_PRE_PERIPH2_CLK_SEL_OFFSET); 583 periph1 = ((reg & MXC_CCM_CBCMR_PRE_PERIPH_CLK_SEL_MASK) 584 >> MXC_CCM_CBCMR_PRE_PERIPH_CLK_SEL_OFFSET); 585 586 /* Checking if PLL2 PFD0 or PLL2 PFD2 is using for periph clock */ 587 if ((periph2 != 0x2) && (periph1 != 0x2)) 588 mask528 |= ANATOP_PFD_CLKGATE_MASK(0); 589 590 if ((periph2 != 0x1) && (periph1 != 0x1) && 591 (periph2 != 0x3) && (periph1 != 0x3)) 592 mask528 |= ANATOP_PFD_CLKGATE_MASK(2); 593 594 writel(mask480, &anatop->pfd_480_set); 595 writel(mask528, &anatop->pfd_528_set); 596 writel(mask480, &anatop->pfd_480_clr); 597 writel(mask528, &anatop->pfd_528_clr); 598 } 599 600 #ifdef CONFIG_IMX_HDMI 601 void imx_enable_hdmi_phy(void) 602 { 603 struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR; 604 u8 reg; 605 reg = readb(&hdmi->phy_conf0); 606 reg |= HDMI_PHY_CONF0_PDZ_MASK; 607 writeb(reg, &hdmi->phy_conf0); 608 udelay(3000); 609 reg |= HDMI_PHY_CONF0_ENTMDS_MASK; 610 writeb(reg, &hdmi->phy_conf0); 611 udelay(3000); 612 reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK; 613 writeb(reg, &hdmi->phy_conf0); 614 writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz); 615 } 616 617 void imx_setup_hdmi(void) 618 { 619 struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 620 struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR; 621 int reg, count; 622 u8 val; 623 624 /* Turn on HDMI PHY clock */ 625 reg = readl(&mxc_ccm->CCGR2); 626 reg |= MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK| 627 MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK; 628 writel(reg, &mxc_ccm->CCGR2); 629 writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz); 630 reg = readl(&mxc_ccm->chsccdr); 631 reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK| 632 MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK| 633 MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK); 634 reg |= (CHSCCDR_PODF_DIVIDE_BY_3 635 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET) 636 |(CHSCCDR_IPU_PRE_CLK_540M_PFD 637 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET); 638 writel(reg, &mxc_ccm->chsccdr); 639 640 /* Clear the overflow condition */ 641 if (readb(&hdmi->ih_fc_stat2) & HDMI_IH_FC_STAT2_OVERFLOW_MASK) { 642 /* TMDS software reset */ 643 writeb((u8)~HDMI_MC_SWRSTZ_TMDSSWRST_REQ, &hdmi->mc_swrstz); 644 val = readb(&hdmi->fc_invidconf); 645 /* Need minimum 3 times to write to clear the register */ 646 for (count = 0 ; count < 5 ; count++) 647 writeb(val, &hdmi->fc_invidconf); 648 } 649 } 650 #endif 651 652 void gpr_init(void) 653 { 654 struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; 655 656 /* enable AXI cache for VDOA/VPU/IPU */ 657 writel(0xF00000CF, &iomux->gpr[4]); 658 if (is_mx6dqp()) { 659 /* set IPU AXI-id1 Qos=0x1 AXI-id0/2/3 Qos=0x7 */ 660 writel(0x77177717, &iomux->gpr[6]); 661 writel(0x77177717, &iomux->gpr[7]); 662 } else { 663 /* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ 664 writel(0x007F007F, &iomux->gpr[6]); 665 writel(0x007F007F, &iomux->gpr[7]); 666 } 667 } 668