1 /* 2 * Copyright (C) 2017 Armadeus Systems 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #include <asm/arch/clock.h> 8 #include <asm/arch/crm_regs.h> 9 #include <asm/arch/imx-regs.h> 10 #include <asm/arch/iomux.h> 11 #include <asm/arch/mx6-pins.h> 12 #include <asm/arch/mx6ul_pins.h> 13 #include <asm/arch/sys_proto.h> 14 #include <asm/gpio.h> 15 #include <asm/mach-imx/iomux-v3.h> 16 #include <asm/io.h> 17 #include <common.h> 18 #include <environment.h> 19 #include <fsl_esdhc.h> 20 #include <mmc.h> 21 22 DECLARE_GLOBAL_DATA_PTR; 23 24 #ifdef CONFIG_FEC_MXC 25 #include <miiphy.h> 26 27 #define MDIO_PAD_CTRL ( \ 28 PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ 29 PAD_CTL_DSE_40ohm \ 30 ) 31 32 #define ENET_PAD_CTRL_PU ( \ 33 PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ 34 PAD_CTL_DSE_40ohm \ 35 ) 36 37 #define ENET_PAD_CTRL_PD ( \ 38 PAD_CTL_HYS | PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_MED | \ 39 PAD_CTL_DSE_40ohm \ 40 ) 41 42 #define ENET_CLK_PAD_CTRL ( \ 43 PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_LOW | \ 44 PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST \ 45 ) 46 47 static iomux_v3_cfg_t const fec1_pads[] = { 48 MX6_PAD_GPIO1_IO06__ENET1_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL), 49 MX6_PAD_GPIO1_IO07__ENET1_MDC | MUX_PAD_CTRL(MDIO_PAD_CTRL), 50 MX6_PAD_ENET1_RX_ER__ENET1_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL_PD), 51 MX6_PAD_ENET1_RX_EN__ENET1_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL_PD), 52 MX6_PAD_ENET1_RX_DATA1__ENET1_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD), 53 MX6_PAD_ENET1_RX_DATA0__ENET1_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD), 54 MX6_PAD_ENET1_TX_DATA0__ENET1_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL_PU), 55 MX6_PAD_ENET1_TX_DATA1__ENET1_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL_PU), 56 MX6_PAD_ENET1_TX_EN__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL_PU), 57 /* PHY Int */ 58 MX6_PAD_NAND_DQS__GPIO4_IO16 | MUX_PAD_CTRL(ENET_PAD_CTRL_PU), 59 /* PHY Reset */ 60 MX6_PAD_NAND_DATA00__GPIO4_IO02 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD), 61 MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL), 62 }; 63 64 int board_phy_config(struct phy_device *phydev) 65 { 66 phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190); 67 68 if (phydev->drv->config) 69 phydev->drv->config(phydev); 70 71 return 0; 72 } 73 74 int board_eth_init(bd_t *bis) 75 { 76 struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; 77 struct gpio_desc rst; 78 int ret; 79 80 /* Use 50M anatop loopback REF_CLK1 for ENET1, 81 * clear gpr1[13], set gpr1[17] */ 82 clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK, 83 IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK); 84 85 ret = enable_fec_anatop_clock(0, ENET_50MHZ); 86 if (ret) 87 return ret; 88 89 enable_enet_clk(1); 90 91 imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads)); 92 93 ret = dm_gpio_lookup_name("GPIO4_2", &rst); 94 if (ret) { 95 printf("Cannot get GPIO4_2\n"); 96 return ret; 97 } 98 99 ret = dm_gpio_request(&rst, "phy-rst"); 100 if (ret) { 101 printf("Cannot request GPIO4_2\n"); 102 return ret; 103 } 104 105 dm_gpio_set_dir_flags(&rst, GPIOD_IS_OUT); 106 dm_gpio_set_value(&rst, 0); 107 udelay(1000); 108 dm_gpio_set_value(&rst, 1); 109 110 return fecmxc_initialize(bis); 111 } 112 #endif /* CONFIG_FEC_MXC */ 113 114 int board_init(void) 115 { 116 /* Address of boot parameters */ 117 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100; 118 119 return 0; 120 } 121 122 int __weak opos6ul_board_late_init(void) 123 { 124 return 0; 125 } 126 127 int board_late_init(void) 128 { 129 struct src *psrc = (struct src *)SRC_BASE_ADDR; 130 unsigned reg = readl(&psrc->sbmr2); 131 132 /* In bootstrap don't use the env vars */ 133 if (((reg & 0x3000000) >> 24) == 0x1) { 134 set_default_env(NULL); 135 env_set("preboot", ""); 136 } 137 138 return opos6ul_board_late_init(); 139 } 140 141 int board_mmc_getcd(struct mmc *mmc) 142 { 143 struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; 144 return cfg->esdhc_base == USDHC1_BASE_ADDR; 145 } 146 147 int dram_init(void) 148 { 149 gd->ram_size = imx_ddr_size(); 150 151 return 0; 152 } 153 154 #ifdef CONFIG_SPL_BUILD 155 #include <asm/arch/mx6-ddr.h> 156 #include <asm/arch/opos6ul.h> 157 #include <libfdt.h> 158 #include <spl.h> 159 160 #define USDHC_PAD_CTRL ( \ 161 PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_MED | \ 162 PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST \ 163 ) 164 165 struct fsl_esdhc_cfg usdhc_cfg[1] = { 166 {USDHC1_BASE_ADDR, 0, 8}, 167 }; 168 169 static iomux_v3_cfg_t const usdhc1_pads[] = { 170 MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 171 MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 172 MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 173 MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 174 MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 175 MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 176 MX6_PAD_NAND_READY_B__USDHC1_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 177 MX6_PAD_NAND_CE0_B__USDHC1_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 178 MX6_PAD_NAND_CE1_B__USDHC1_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 179 MX6_PAD_NAND_CLE__USDHC1_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 180 }; 181 182 static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = { 183 .grp_addds = 0x00000030, 184 .grp_ddrmode_ctl = 0x00020000, 185 .grp_b0ds = 0x00000030, 186 .grp_ctlds = 0x00000030, 187 .grp_b1ds = 0x00000030, 188 .grp_ddrpke = 0x00000000, 189 .grp_ddrmode = 0x00020000, 190 .grp_ddr_type = 0x000c0000, 191 }; 192 193 static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = { 194 .dram_dqm0 = 0x00000030, 195 .dram_dqm1 = 0x00000030, 196 .dram_ras = 0x00000030, 197 .dram_cas = 0x00000030, 198 .dram_odt0 = 0x00000030, 199 .dram_odt1 = 0x00000030, 200 .dram_sdba2 = 0x00000000, 201 .dram_sdclk_0 = 0x00000008, 202 .dram_sdqs0 = 0x00000038, 203 .dram_sdqs1 = 0x00000030, 204 .dram_reset = 0x00000030, 205 }; 206 207 static struct mx6_mmdc_calibration mx6_mmcd_calib = { 208 .p0_mpwldectrl0 = 0x00070007, 209 .p0_mpdgctrl0 = 0x41490145, 210 .p0_mprddlctl = 0x40404546, 211 .p0_mpwrdlctl = 0x4040524D, 212 }; 213 214 struct mx6_ddr_sysinfo ddr_sysinfo = { 215 .dsize = 0, 216 .cs_density = 20, 217 .ncs = 1, 218 .cs1_mirror = 0, 219 .rtt_wr = 2, 220 .rtt_nom = 1, /* RTT_Nom = RZQ/2 */ 221 .walat = 1, /* Write additional latency */ 222 .ralat = 5, /* Read additional latency */ 223 .mif3_mode = 3, /* Command prediction working mode */ 224 .bi_on = 1, /* Bank interleaving enabled */ 225 .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */ 226 .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */ 227 .ddr_type = DDR_TYPE_DDR3, 228 }; 229 230 static struct mx6_ddr3_cfg mem_ddr = { 231 .mem_speed = 800, 232 .density = 2, 233 .width = 16, 234 .banks = 8, 235 .rowaddr = 14, 236 .coladdr = 10, 237 .pagesz = 2, 238 .trcd = 1500, 239 .trcmin = 5250, 240 .trasmin = 3750, 241 }; 242 243 int board_mmc_init(bd_t *bis) 244 { 245 imx_iomux_v3_setup_multiple_pads(usdhc1_pads, ARRAY_SIZE(usdhc1_pads)); 246 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); 247 return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); 248 } 249 250 static void ccgr_init(void) 251 { 252 struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 253 254 writel(0xFFFFFFFF, &ccm->CCGR0); 255 writel(0xFFFFFFFF, &ccm->CCGR1); 256 writel(0xFFFFFFFF, &ccm->CCGR2); 257 writel(0xFFFFFFFF, &ccm->CCGR3); 258 writel(0xFFFFFFFF, &ccm->CCGR4); 259 writel(0xFFFFFFFF, &ccm->CCGR5); 260 writel(0xFFFFFFFF, &ccm->CCGR6); 261 writel(0xFFFFFFFF, &ccm->CCGR7); 262 } 263 264 static void spl_dram_init(void) 265 { 266 struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR; 267 struct fuse_bank *bank = &ocotp->bank[4]; 268 struct fuse_bank4_regs *fuse = 269 (struct fuse_bank4_regs *)bank->fuse_regs; 270 int reg = readl(&fuse->gp1); 271 272 /* 512MB of RAM */ 273 if (reg & 0x1) { 274 mem_ddr.density = 4; 275 mem_ddr.rowaddr = 15; 276 mem_ddr.trcd = 1375; 277 mem_ddr.trcmin = 4875; 278 mem_ddr.trasmin = 3500; 279 } 280 281 mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs); 282 mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr); 283 } 284 285 void board_init_f(ulong dummy) 286 { 287 ccgr_init(); 288 289 /* setup AIPS and disable watchdog */ 290 arch_cpu_init(); 291 292 /* setup GP timer */ 293 timer_init(); 294 295 /* UART clocks enabled and gd valid - init serial console */ 296 opos6ul_setup_uart_debug(); 297 preloader_console_init(); 298 299 /* DDR initialization */ 300 spl_dram_init(); 301 } 302 #endif /* CONFIG_SPL_BUILD */ 303