1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Copyright (C) 2015-2016 Freescale Semiconductor, Inc. 4 * Copyright (C) 2016 Grinn 5 */ 6 7 #include <asm/arch/clock.h> 8 #include <asm/arch/iomux.h> 9 #include <asm/arch/imx-regs.h> 10 #include <asm/arch/crm_regs.h> 11 #include <asm/arch/mx6ul_pins.h> 12 #include <asm/arch/mx6-pins.h> 13 #include <asm/arch/sys_proto.h> 14 #include <asm/gpio.h> 15 #include <asm/mach-imx/iomux-v3.h> 16 #include <asm/mach-imx/boot_mode.h> 17 #include <asm/io.h> 18 #include <common.h> 19 #include <fsl_esdhc.h> 20 #include <linux/sizes.h> 21 #include <mmc.h> 22 23 DECLARE_GLOBAL_DATA_PTR; 24 25 #define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ 26 PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \ 27 PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) 28 29 int dram_init(void) 30 { 31 gd->ram_size = imx_ddr_size(); 32 33 return 0; 34 } 35 36 static iomux_v3_cfg_t const emmc_pads[] = { 37 MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), 38 MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), 39 MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 40 MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 41 MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 42 MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 43 MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 44 MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 45 MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 46 MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), 47 48 /* RST_B */ 49 MX6_PAD_NAND_ALE__GPIO4_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL), 50 }; 51 52 #ifdef CONFIG_FSL_ESDHC 53 static struct fsl_esdhc_cfg emmc_cfg = {USDHC2_BASE_ADDR, 0, 8}; 54 55 #define EMMC_PWR_GPIO IMX_GPIO_NR(4, 10) 56 57 int litesom_mmc_init(bd_t *bis) 58 { 59 int ret; 60 61 /* eMMC */ 62 imx_iomux_v3_setup_multiple_pads(emmc_pads, ARRAY_SIZE(emmc_pads)); 63 gpio_direction_output(EMMC_PWR_GPIO, 0); 64 udelay(500); 65 gpio_direction_output(EMMC_PWR_GPIO, 1); 66 emmc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); 67 68 ret = fsl_esdhc_initialize(bis, &emmc_cfg); 69 if (ret) { 70 printf("Warning: failed to initialize mmc dev 1 (eMMC)\n"); 71 return ret; 72 } 73 74 return 0; 75 } 76 #endif 77 78 #ifdef CONFIG_SPL_BUILD 79 #include <linux/libfdt.h> 80 #include <spl.h> 81 #include <asm/arch/mx6-ddr.h> 82 83 84 static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = { 85 .grp_addds = 0x00000030, 86 .grp_ddrmode_ctl = 0x00020000, 87 .grp_b0ds = 0x00000030, 88 .grp_ctlds = 0x00000030, 89 .grp_b1ds = 0x00000030, 90 .grp_ddrpke = 0x00000000, 91 .grp_ddrmode = 0x00020000, 92 .grp_ddr_type = 0x000c0000, 93 }; 94 95 static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = { 96 .dram_dqm0 = 0x00000030, 97 .dram_dqm1 = 0x00000030, 98 .dram_ras = 0x00000030, 99 .dram_cas = 0x00000030, 100 .dram_odt0 = 0x00000030, 101 .dram_odt1 = 0x00000030, 102 .dram_sdba2 = 0x00000000, 103 .dram_sdclk_0 = 0x00000030, 104 .dram_sdqs0 = 0x00000030, 105 .dram_sdqs1 = 0x00000030, 106 .dram_reset = 0x00000030, 107 }; 108 109 static struct mx6_mmdc_calibration mx6_mmcd_calib = { 110 .p0_mpwldectrl0 = 0x00000000, 111 .p0_mpdgctrl0 = 0x41570155, 112 .p0_mprddlctl = 0x4040474A, 113 .p0_mpwrdlctl = 0x40405550, 114 }; 115 116 struct mx6_ddr_sysinfo ddr_sysinfo = { 117 .dsize = 0, 118 .cs_density = 20, 119 .ncs = 1, 120 .cs1_mirror = 0, 121 .rtt_wr = 2, 122 .rtt_nom = 1, /* RTT_Nom = RZQ/2 */ 123 .walat = 0, /* Write additional latency */ 124 .ralat = 5, /* Read additional latency */ 125 .mif3_mode = 3, /* Command prediction working mode */ 126 .bi_on = 1, /* Bank interleaving enabled */ 127 .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */ 128 .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */ 129 .ddr_type = DDR_TYPE_DDR3, 130 .refsel = 0, /* Refresh cycles at 64KHz */ 131 .refr = 1, /* 2 refresh commands per refresh cycle */ 132 }; 133 134 static struct mx6_ddr3_cfg mem_ddr = { 135 .mem_speed = 800, 136 .density = 4, 137 .width = 16, 138 .banks = 8, 139 .rowaddr = 15, 140 .coladdr = 10, 141 .pagesz = 2, 142 .trcd = 1375, 143 .trcmin = 4875, 144 .trasmin = 3500, 145 }; 146 147 static void ccgr_init(void) 148 { 149 struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; 150 151 writel(0xFFFFFFFF, &ccm->CCGR0); 152 writel(0xFFFFFFFF, &ccm->CCGR1); 153 writel(0xFFFFFFFF, &ccm->CCGR2); 154 writel(0xFFFFFFFF, &ccm->CCGR3); 155 writel(0xFFFFFFFF, &ccm->CCGR4); 156 writel(0xFFFFFFFF, &ccm->CCGR5); 157 writel(0xFFFFFFFF, &ccm->CCGR6); 158 writel(0xFFFFFFFF, &ccm->CCGR7); 159 } 160 161 static void spl_dram_init(void) 162 { 163 unsigned long ram_size; 164 165 mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs); 166 mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr); 167 168 /* 169 * Get actual RAM size, so we can adjust DDR row size for <512M 170 * memories 171 */ 172 ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE, SZ_512M); 173 if (ram_size < SZ_512M) { 174 mem_ddr.rowaddr = 14; 175 mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr); 176 } 177 } 178 179 void litesom_init_f(void) 180 { 181 ccgr_init(); 182 183 /* setup AIPS and disable watchdog */ 184 arch_cpu_init(); 185 186 #ifdef CONFIG_BOARD_EARLY_INIT_F 187 board_early_init_f(); 188 #endif 189 190 /* setup GP timer */ 191 timer_init(); 192 193 /* UART clocks enabled and gd valid - init serial console */ 194 preloader_console_init(); 195 196 /* DDR initialization */ 197 spl_dram_init(); 198 } 199 #endif 200