1 /* 2 * Copyright (C) 2014 Gateworks Corporation 3 * Author: Tim Harvey <tharvey@gateworks.com> 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 #include <common.h> 9 #include <linux/types.h> 10 #include <asm/arch/clock.h> 11 #include <asm/arch/mx6-ddr.h> 12 #include <asm/arch/sys_proto.h> 13 #include <asm/io.h> 14 #include <asm/types.h> 15 #include <wait_bit.h> 16 17 #if defined(CONFIG_MX6_DDRCAL) 18 static void reset_read_data_fifos(void) 19 { 20 struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR; 21 22 /* Reset data FIFOs twice. */ 23 setbits_le32(&mmdc0->mpdgctrl0, 1 << 31); 24 wait_for_bit("MMDC", &mmdc0->mpdgctrl0, 1 << 31, 0, 100, 0); 25 26 setbits_le32(&mmdc0->mpdgctrl0, 1 << 31); 27 wait_for_bit("MMDC", &mmdc0->mpdgctrl0, 1 << 31, 0, 100, 0); 28 } 29 30 static void precharge_all(const bool cs0_enable, const bool cs1_enable) 31 { 32 struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR; 33 34 /* 35 * Issue the Precharge-All command to the DDR device for both 36 * chip selects. Note, CON_REQ bit should also remain set. If 37 * only using one chip select, then precharge only the desired 38 * chip select. 39 */ 40 if (cs0_enable) { /* CS0 */ 41 writel(0x04008050, &mmdc0->mdscr); 42 wait_for_bit("MMDC", &mmdc0->mdscr, 1 << 14, 1, 100, 0); 43 } 44 45 if (cs1_enable) { /* CS1 */ 46 writel(0x04008058, &mmdc0->mdscr); 47 wait_for_bit("MMDC", &mmdc0->mdscr, 1 << 14, 1, 100, 0); 48 } 49 } 50 51 static void force_delay_measurement(int bus_size) 52 { 53 struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR; 54 struct mmdc_p_regs *mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR; 55 56 writel(0x800, &mmdc0->mpmur0); 57 if (bus_size == 0x2) 58 writel(0x800, &mmdc1->mpmur0); 59 } 60 61 static void modify_dg_result(u32 *reg_st0, u32 *reg_st1, u32 *reg_ctrl) 62 { 63 u32 dg_tmp_val, dg_dl_abs_offset, dg_hc_del, val_ctrl; 64 65 /* 66 * DQS gating absolute offset should be modified from reflecting 67 * (HW_DG_LOWx + HW_DG_UPx)/2 to reflecting (HW_DG_UPx - 0x80) 68 */ 69 70 val_ctrl = readl(reg_ctrl); 71 val_ctrl &= 0xf0000000; 72 73 dg_tmp_val = ((readl(reg_st0) & 0x07ff0000) >> 16) - 0xc0; 74 dg_dl_abs_offset = dg_tmp_val & 0x7f; 75 dg_hc_del = (dg_tmp_val & 0x780) << 1; 76 77 val_ctrl |= dg_dl_abs_offset + dg_hc_del; 78 79 dg_tmp_val = ((readl(reg_st1) & 0x07ff0000) >> 16) - 0xc0; 80 dg_dl_abs_offset = dg_tmp_val & 0x7f; 81 dg_hc_del = (dg_tmp_val & 0x780) << 1; 82 83 val_ctrl |= (dg_dl_abs_offset + dg_hc_del) << 16; 84 85 writel(val_ctrl, reg_ctrl); 86 } 87 88 int mmdc_do_write_level_calibration(struct mx6_ddr_sysinfo const *sysinfo) 89 { 90 struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR; 91 struct mmdc_p_regs *mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR; 92 u32 esdmisc_val, zq_val; 93 u32 errors = 0; 94 u32 ldectrl[4] = {0}; 95 u32 ddr_mr1 = 0x4; 96 u32 rwalat_max; 97 98 /* 99 * Stash old values in case calibration fails, 100 * we need to restore them 101 */ 102 ldectrl[0] = readl(&mmdc0->mpwldectrl0); 103 ldectrl[1] = readl(&mmdc0->mpwldectrl1); 104 if (sysinfo->dsize == 2) { 105 ldectrl[2] = readl(&mmdc1->mpwldectrl0); 106 ldectrl[3] = readl(&mmdc1->mpwldectrl1); 107 } 108 109 /* disable DDR logic power down timer */ 110 clrbits_le32(&mmdc0->mdpdc, 0xff00); 111 112 /* disable Adopt power down timer */ 113 setbits_le32(&mmdc0->mapsr, 0x1); 114 115 debug("Starting write leveling calibration.\n"); 116 117 /* 118 * 2. disable auto refresh and ZQ calibration 119 * before proceeding with Write Leveling calibration 120 */ 121 esdmisc_val = readl(&mmdc0->mdref); 122 writel(0x0000C000, &mmdc0->mdref); 123 zq_val = readl(&mmdc0->mpzqhwctrl); 124 writel(zq_val & ~0x3, &mmdc0->mpzqhwctrl); 125 126 /* 3. increase walat and ralat to maximum */ 127 rwalat_max = (1 << 6) | (1 << 7) | (1 << 8) | (1 << 16) | (1 << 17); 128 setbits_le32(&mmdc0->mdmisc, rwalat_max); 129 if (sysinfo->dsize == 2) 130 setbits_le32(&mmdc1->mdmisc, rwalat_max); 131 /* 132 * 4 & 5. Configure the external DDR device to enter write-leveling 133 * mode through Load Mode Register command. 134 * Register setting: 135 * Bits[31:16] MR1 value (0x0080 write leveling enable) 136 * Bit[9] set WL_EN to enable MMDC DQS output 137 * Bits[6:4] set CMD bits for Load Mode Register programming 138 * Bits[2:0] set CMD_BA to 0x1 for DDR MR1 programming 139 */ 140 writel(0x00808231, &mmdc0->mdscr); 141 142 /* 6. Activate automatic calibration by setting MPWLGCR[HW_WL_EN] */ 143 writel(0x00000001, &mmdc0->mpwlgcr); 144 145 /* 146 * 7. Upon completion of this process the MMDC de-asserts 147 * the MPWLGCR[HW_WL_EN] 148 */ 149 wait_for_bit("MMDC", &mmdc0->mpwlgcr, 1 << 0, 0, 100, 0); 150 151 /* 152 * 8. check for any errors: check both PHYs for x64 configuration, 153 * if x32, check only PHY0 154 */ 155 if (readl(&mmdc0->mpwlgcr) & 0x00000F00) 156 errors |= 1; 157 if (sysinfo->dsize == 2) 158 if (readl(&mmdc1->mpwlgcr) & 0x00000F00) 159 errors |= 2; 160 161 debug("Ending write leveling calibration. Error mask: 0x%x\n", errors); 162 163 /* check to see if cal failed */ 164 if ((readl(&mmdc0->mpwldectrl0) == 0x001F001F) && 165 (readl(&mmdc0->mpwldectrl1) == 0x001F001F) && 166 ((sysinfo->dsize < 2) || 167 ((readl(&mmdc1->mpwldectrl0) == 0x001F001F) && 168 (readl(&mmdc1->mpwldectrl1) == 0x001F001F)))) { 169 debug("Cal seems to have soft-failed due to memory not supporting write leveling on all channels. Restoring original write leveling values.\n"); 170 writel(ldectrl[0], &mmdc0->mpwldectrl0); 171 writel(ldectrl[1], &mmdc0->mpwldectrl1); 172 if (sysinfo->dsize == 2) { 173 writel(ldectrl[2], &mmdc1->mpwldectrl0); 174 writel(ldectrl[3], &mmdc1->mpwldectrl1); 175 } 176 errors |= 4; 177 } 178 179 /* 180 * User should issue MRS command to exit write leveling mode 181 * through Load Mode Register command 182 * Register setting: 183 * Bits[31:16] MR1 value "ddr_mr1" value from initialization 184 * Bit[9] clear WL_EN to disable MMDC DQS output 185 * Bits[6:4] set CMD bits for Load Mode Register programming 186 * Bits[2:0] set CMD_BA to 0x1 for DDR MR1 programming 187 */ 188 writel((ddr_mr1 << 16) + 0x8031, &mmdc0->mdscr); 189 190 /* re-enable auto refresh and zq cal */ 191 writel(esdmisc_val, &mmdc0->mdref); 192 writel(zq_val, &mmdc0->mpzqhwctrl); 193 194 debug("\tMMDC_MPWLDECTRL0 after write level cal: 0x%08X\n", 195 readl(&mmdc0->mpwldectrl0)); 196 debug("\tMMDC_MPWLDECTRL1 after write level cal: 0x%08X\n", 197 readl(&mmdc0->mpwldectrl1)); 198 if (sysinfo->dsize == 2) { 199 debug("\tMMDC_MPWLDECTRL0 after write level cal: 0x%08X\n", 200 readl(&mmdc1->mpwldectrl0)); 201 debug("\tMMDC_MPWLDECTRL1 after write level cal: 0x%08X\n", 202 readl(&mmdc1->mpwldectrl1)); 203 } 204 205 /* We must force a readback of these values, to get them to stick */ 206 readl(&mmdc0->mpwldectrl0); 207 readl(&mmdc0->mpwldectrl1); 208 if (sysinfo->dsize == 2) { 209 readl(&mmdc1->mpwldectrl0); 210 readl(&mmdc1->mpwldectrl1); 211 } 212 213 /* enable DDR logic power down timer: */ 214 setbits_le32(&mmdc0->mdpdc, 0x00005500); 215 216 /* Enable Adopt power down timer: */ 217 clrbits_le32(&mmdc0->mapsr, 0x1); 218 219 /* Clear CON_REQ */ 220 writel(0, &mmdc0->mdscr); 221 222 return errors; 223 } 224 225 int mmdc_do_dqs_calibration(struct mx6_ddr_sysinfo const *sysinfo) 226 { 227 struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR; 228 struct mmdc_p_regs *mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR; 229 struct mx6dq_iomux_ddr_regs *mx6_ddr_iomux = 230 (struct mx6dq_iomux_ddr_regs *)MX6DQ_IOM_DDR_BASE; 231 bool cs0_enable; 232 bool cs1_enable; 233 bool cs0_enable_initial; 234 bool cs1_enable_initial; 235 u32 esdmisc_val; 236 u32 temp_ref; 237 u32 pddword = 0x00ffff00; /* best so far, place into MPPDCMPR1 */ 238 u32 errors = 0; 239 u32 initdelay = 0x40404040; 240 241 /* check to see which chip selects are enabled */ 242 cs0_enable_initial = readl(&mmdc0->mdctl) & 0x80000000; 243 cs1_enable_initial = readl(&mmdc0->mdctl) & 0x40000000; 244 245 /* disable DDR logic power down timer: */ 246 clrbits_le32(&mmdc0->mdpdc, 0xff00); 247 248 /* disable Adopt power down timer: */ 249 setbits_le32(&mmdc0->mapsr, 0x1); 250 251 /* set DQS pull ups */ 252 setbits_le32(&mx6_ddr_iomux->dram_sdqs0, 0x7000); 253 setbits_le32(&mx6_ddr_iomux->dram_sdqs1, 0x7000); 254 setbits_le32(&mx6_ddr_iomux->dram_sdqs2, 0x7000); 255 setbits_le32(&mx6_ddr_iomux->dram_sdqs3, 0x7000); 256 setbits_le32(&mx6_ddr_iomux->dram_sdqs4, 0x7000); 257 setbits_le32(&mx6_ddr_iomux->dram_sdqs5, 0x7000); 258 setbits_le32(&mx6_ddr_iomux->dram_sdqs6, 0x7000); 259 setbits_le32(&mx6_ddr_iomux->dram_sdqs7, 0x7000); 260 261 /* Save old RALAT and WALAT values */ 262 esdmisc_val = readl(&mmdc0->mdmisc); 263 264 setbits_le32(&mmdc0->mdmisc, 265 (1 << 6) | (1 << 7) | (1 << 8) | (1 << 16) | (1 << 17)); 266 267 /* Disable auto refresh before proceeding with calibration */ 268 temp_ref = readl(&mmdc0->mdref); 269 writel(0x0000c000, &mmdc0->mdref); 270 271 /* 272 * Per the ref manual, issue one refresh cycle MDSCR[CMD]= 0x2, 273 * this also sets the CON_REQ bit. 274 */ 275 if (cs0_enable_initial) 276 writel(0x00008020, &mmdc0->mdscr); 277 if (cs1_enable_initial) 278 writel(0x00008028, &mmdc0->mdscr); 279 280 /* poll to make sure the con_ack bit was asserted */ 281 wait_for_bit("MMDC", &mmdc0->mdscr, 1 << 14, 1, 100, 0); 282 283 /* 284 * Check MDMISC register CALIB_PER_CS to see which CS calibration 285 * is targeted to (under normal cases, it should be cleared 286 * as this is the default value, indicating calibration is directed 287 * to CS0). 288 * Disable the other chip select not being target for calibration 289 * to avoid any potential issues. This will get re-enabled at end 290 * of calibration. 291 */ 292 if ((readl(&mmdc0->mdmisc) & 0x00100000) == 0) 293 clrbits_le32(&mmdc0->mdctl, 1 << 30); /* clear SDE_1 */ 294 else 295 clrbits_le32(&mmdc0->mdctl, 1 << 31); /* clear SDE_0 */ 296 297 /* 298 * Check to see which chip selects are now enabled for 299 * the remainder of the calibration. 300 */ 301 cs0_enable = readl(&mmdc0->mdctl) & 0x80000000; 302 cs1_enable = readl(&mmdc0->mdctl) & 0x40000000; 303 304 precharge_all(cs0_enable, cs1_enable); 305 306 /* Write the pre-defined value into MPPDCMPR1 */ 307 writel(pddword, &mmdc0->mppdcmpr1); 308 309 /* 310 * Issue a write access to the external DDR device by setting 311 * the bit SW_DUMMY_WR (bit 0) in the MPSWDAR0 and then poll 312 * this bit until it clears to indicate completion of the write access. 313 */ 314 setbits_le32(&mmdc0->mpswdar0, 1); 315 wait_for_bit("MMDC", &mmdc0->mpswdar0, 1 << 0, 0, 100, 0); 316 317 /* Set the RD_DL_ABS# bits to their default values 318 * (will be calibrated later in the read delay-line calibration). 319 * Both PHYs for x64 configuration, if x32, do only PHY0. 320 */ 321 writel(initdelay, &mmdc0->mprddlctl); 322 if (sysinfo->dsize == 0x2) 323 writel(initdelay, &mmdc1->mprddlctl); 324 325 /* Force a measurment, for previous delay setup to take effect. */ 326 force_delay_measurement(sysinfo->dsize); 327 328 /* 329 * *************************** 330 * Read DQS Gating calibration 331 * *************************** 332 */ 333 debug("Starting Read DQS Gating calibration.\n"); 334 335 /* 336 * Reset the read data FIFOs (two resets); only need to issue reset 337 * to PHY0 since in x64 mode, the reset will also go to PHY1. 338 */ 339 reset_read_data_fifos(); 340 341 /* 342 * Start the automatic read DQS gating calibration process by 343 * asserting MPDGCTRL0[HW_DG_EN] and MPDGCTRL0[DG_CMP_CYC] 344 * and then poll MPDGCTRL0[HW_DG_EN]] until this bit clears 345 * to indicate completion. 346 * Also, ensure that MPDGCTRL0[HW_DG_ERR] is clear to indicate 347 * no errors were seen during calibration. 348 */ 349 350 /* 351 * Set bit 30: chooses option to wait 32 cycles instead of 352 * 16 before comparing read data. 353 */ 354 setbits_le32(&mmdc0->mpdgctrl0, 1 << 30); 355 if (sysinfo->dsize == 2) 356 setbits_le32(&mmdc1->mpdgctrl0, 1 << 30); 357 358 /* Set bit 28 to start automatic read DQS gating calibration */ 359 setbits_le32(&mmdc0->mpdgctrl0, 5 << 28); 360 361 /* Poll for completion. MPDGCTRL0[HW_DG_EN] should be 0 */ 362 wait_for_bit("MMDC", &mmdc0->mpdgctrl0, 1 << 28, 0, 100, 0); 363 364 /* 365 * Check to see if any errors were encountered during calibration 366 * (check MPDGCTRL0[HW_DG_ERR]). 367 * Check both PHYs for x64 configuration, if x32, check only PHY0. 368 */ 369 if (readl(&mmdc0->mpdgctrl0) & 0x00001000) 370 errors |= 1; 371 372 if ((sysinfo->dsize == 0x2) && (readl(&mmdc1->mpdgctrl0) & 0x00001000)) 373 errors |= 2; 374 375 /* now disable mpdgctrl0[DG_CMP_CYC] */ 376 clrbits_le32(&mmdc0->mpdgctrl0, 1 << 30); 377 if (sysinfo->dsize == 2) 378 clrbits_le32(&mmdc1->mpdgctrl0, 1 << 30); 379 380 /* 381 * DQS gating absolute offset should be modified from 382 * reflecting (HW_DG_LOWx + HW_DG_UPx)/2 to 383 * reflecting (HW_DG_UPx - 0x80) 384 */ 385 modify_dg_result(&mmdc0->mpdghwst0, &mmdc0->mpdghwst1, 386 &mmdc0->mpdgctrl0); 387 modify_dg_result(&mmdc0->mpdghwst2, &mmdc0->mpdghwst3, 388 &mmdc0->mpdgctrl1); 389 if (sysinfo->dsize == 0x2) { 390 modify_dg_result(&mmdc1->mpdghwst0, &mmdc1->mpdghwst1, 391 &mmdc1->mpdgctrl0); 392 modify_dg_result(&mmdc1->mpdghwst2, &mmdc1->mpdghwst3, 393 &mmdc1->mpdgctrl1); 394 } 395 debug("Ending Read DQS Gating calibration. Error mask: 0x%x\n", errors); 396 397 /* 398 * ********************** 399 * Read Delay calibration 400 * ********************** 401 */ 402 debug("Starting Read Delay calibration.\n"); 403 404 reset_read_data_fifos(); 405 406 /* 407 * 4. Issue the Precharge-All command to the DDR device for both 408 * chip selects. If only using one chip select, then precharge 409 * only the desired chip select. 410 */ 411 precharge_all(cs0_enable, cs1_enable); 412 413 /* 414 * 9. Read delay-line calibration 415 * Start the automatic read calibration process by asserting 416 * MPRDDLHWCTL[HW_RD_DL_EN]. 417 */ 418 writel(0x00000030, &mmdc0->mprddlhwctl); 419 420 /* 421 * 10. poll for completion 422 * MMDC indicates that the write data calibration had finished by 423 * setting MPRDDLHWCTL[HW_RD_DL_EN] = 0. Also, ensure that 424 * no error bits were set. 425 */ 426 wait_for_bit("MMDC", &mmdc0->mprddlhwctl, 1 << 4, 0, 100, 0); 427 428 /* check both PHYs for x64 configuration, if x32, check only PHY0 */ 429 if (readl(&mmdc0->mprddlhwctl) & 0x0000000f) 430 errors |= 4; 431 432 if ((sysinfo->dsize == 0x2) && 433 (readl(&mmdc1->mprddlhwctl) & 0x0000000f)) 434 errors |= 8; 435 436 debug("Ending Read Delay calibration. Error mask: 0x%x\n", errors); 437 438 /* 439 * *********************** 440 * Write Delay Calibration 441 * *********************** 442 */ 443 debug("Starting Write Delay calibration.\n"); 444 445 reset_read_data_fifos(); 446 447 /* 448 * 4. Issue the Precharge-All command to the DDR device for both 449 * chip selects. If only using one chip select, then precharge 450 * only the desired chip select. 451 */ 452 precharge_all(cs0_enable, cs1_enable); 453 454 /* 455 * 8. Set the WR_DL_ABS# bits to their default values. 456 * Both PHYs for x64 configuration, if x32, do only PHY0. 457 */ 458 writel(initdelay, &mmdc0->mpwrdlctl); 459 if (sysinfo->dsize == 0x2) 460 writel(initdelay, &mmdc1->mpwrdlctl); 461 462 /* 463 * XXX This isn't in the manual. Force a measurement, 464 * for previous delay setup to effect. 465 */ 466 force_delay_measurement(sysinfo->dsize); 467 468 /* 469 * 9. 10. Start the automatic write calibration process 470 * by asserting MPWRDLHWCTL0[HW_WR_DL_EN]. 471 */ 472 writel(0x00000030, &mmdc0->mpwrdlhwctl); 473 474 /* 475 * Poll for completion. 476 * MMDC indicates that the write data calibration had finished 477 * by setting MPWRDLHWCTL[HW_WR_DL_EN] = 0. 478 * Also, ensure that no error bits were set. 479 */ 480 wait_for_bit("MMDC", &mmdc0->mpwrdlhwctl, 1 << 4, 0, 100, 0); 481 482 /* Check both PHYs for x64 configuration, if x32, check only PHY0 */ 483 if (readl(&mmdc0->mpwrdlhwctl) & 0x0000000f) 484 errors |= 16; 485 486 if ((sysinfo->dsize == 0x2) && 487 (readl(&mmdc1->mpwrdlhwctl) & 0x0000000f)) 488 errors |= 32; 489 490 debug("Ending Write Delay calibration. Error mask: 0x%x\n", errors); 491 492 reset_read_data_fifos(); 493 494 /* Enable DDR logic power down timer */ 495 setbits_le32(&mmdc0->mdpdc, 0x00005500); 496 497 /* Enable Adopt power down timer */ 498 clrbits_le32(&mmdc0->mapsr, 0x1); 499 500 /* Restore MDMISC value (RALAT, WALAT) to MMDCP1 */ 501 writel(esdmisc_val, &mmdc0->mdmisc); 502 503 /* Clear DQS pull ups */ 504 clrbits_le32(&mx6_ddr_iomux->dram_sdqs0, 0x7000); 505 clrbits_le32(&mx6_ddr_iomux->dram_sdqs1, 0x7000); 506 clrbits_le32(&mx6_ddr_iomux->dram_sdqs2, 0x7000); 507 clrbits_le32(&mx6_ddr_iomux->dram_sdqs3, 0x7000); 508 clrbits_le32(&mx6_ddr_iomux->dram_sdqs4, 0x7000); 509 clrbits_le32(&mx6_ddr_iomux->dram_sdqs5, 0x7000); 510 clrbits_le32(&mx6_ddr_iomux->dram_sdqs6, 0x7000); 511 clrbits_le32(&mx6_ddr_iomux->dram_sdqs7, 0x7000); 512 513 /* Re-enable SDE (chip selects) if they were set initially */ 514 if (cs1_enable_initial) 515 /* Set SDE_1 */ 516 setbits_le32(&mmdc0->mdctl, 1 << 30); 517 518 if (cs0_enable_initial) 519 /* Set SDE_0 */ 520 setbits_le32(&mmdc0->mdctl, 1 << 31); 521 522 /* Re-enable to auto refresh */ 523 writel(temp_ref, &mmdc0->mdref); 524 525 /* Clear the MDSCR (including the con_req bit) */ 526 writel(0x0, &mmdc0->mdscr); /* CS0 */ 527 528 /* Poll to make sure the con_ack bit is clear */ 529 wait_for_bit("MMDC", &mmdc0->mdscr, 1 << 14, 0, 100, 0); 530 531 /* 532 * Print out the registers that were updated as a result 533 * of the calibration process. 534 */ 535 debug("MMDC registers updated from calibration\n"); 536 debug("Read DQS gating calibration:\n"); 537 debug("\tMPDGCTRL0 PHY0 = 0x%08X\n", readl(&mmdc0->mpdgctrl0)); 538 debug("\tMPDGCTRL1 PHY0 = 0x%08X\n", readl(&mmdc0->mpdgctrl1)); 539 if (sysinfo->dsize == 2) { 540 debug("\tMPDGCTRL0 PHY1 = 0x%08X\n", readl(&mmdc1->mpdgctrl0)); 541 debug("\tMPDGCTRL1 PHY1 = 0x%08X\n", readl(&mmdc1->mpdgctrl1)); 542 } 543 debug("Read calibration:\n"); 544 debug("\tMPRDDLCTL PHY0 = 0x%08X\n", readl(&mmdc0->mprddlctl)); 545 if (sysinfo->dsize == 2) 546 debug("\tMPRDDLCTL PHY1 = 0x%08X\n", readl(&mmdc1->mprddlctl)); 547 debug("Write calibration:\n"); 548 debug("\tMPWRDLCTL PHY0 = 0x%08X\n", readl(&mmdc0->mpwrdlctl)); 549 if (sysinfo->dsize == 2) 550 debug("\tMPWRDLCTL PHY1 = 0x%08X\n", readl(&mmdc1->mpwrdlctl)); 551 552 /* 553 * Registers below are for debugging purposes. These print out 554 * the upper and lower boundaries captured during 555 * read DQS gating calibration. 556 */ 557 debug("Status registers bounds for read DQS gating:\n"); 558 debug("\tMPDGHWST0 PHY0 = 0x%08x\n", readl(&mmdc0->mpdghwst0)); 559 debug("\tMPDGHWST1 PHY0 = 0x%08x\n", readl(&mmdc0->mpdghwst1)); 560 debug("\tMPDGHWST2 PHY0 = 0x%08x\n", readl(&mmdc0->mpdghwst2)); 561 debug("\tMPDGHWST3 PHY0 = 0x%08x\n", readl(&mmdc0->mpdghwst3)); 562 if (sysinfo->dsize == 2) { 563 debug("\tMPDGHWST0 PHY1 = 0x%08x\n", readl(&mmdc1->mpdghwst0)); 564 debug("\tMPDGHWST1 PHY1 = 0x%08x\n", readl(&mmdc1->mpdghwst1)); 565 debug("\tMPDGHWST2 PHY1 = 0x%08x\n", readl(&mmdc1->mpdghwst2)); 566 debug("\tMPDGHWST3 PHY1 = 0x%08x\n", readl(&mmdc1->mpdghwst3)); 567 } 568 569 debug("Final do_dqs_calibration error mask: 0x%x\n", errors); 570 571 return errors; 572 } 573 #endif 574 575 #if defined(CONFIG_MX6SX) 576 /* Configure MX6SX mmdc iomux */ 577 void mx6sx_dram_iocfg(unsigned width, 578 const struct mx6sx_iomux_ddr_regs *ddr, 579 const struct mx6sx_iomux_grp_regs *grp) 580 { 581 struct mx6sx_iomux_ddr_regs *mx6_ddr_iomux; 582 struct mx6sx_iomux_grp_regs *mx6_grp_iomux; 583 584 mx6_ddr_iomux = (struct mx6sx_iomux_ddr_regs *)MX6SX_IOM_DDR_BASE; 585 mx6_grp_iomux = (struct mx6sx_iomux_grp_regs *)MX6SX_IOM_GRP_BASE; 586 587 /* DDR IO TYPE */ 588 writel(grp->grp_ddr_type, &mx6_grp_iomux->grp_ddr_type); 589 writel(grp->grp_ddrpke, &mx6_grp_iomux->grp_ddrpke); 590 591 /* CLOCK */ 592 writel(ddr->dram_sdclk_0, &mx6_ddr_iomux->dram_sdclk_0); 593 594 /* ADDRESS */ 595 writel(ddr->dram_cas, &mx6_ddr_iomux->dram_cas); 596 writel(ddr->dram_ras, &mx6_ddr_iomux->dram_ras); 597 writel(grp->grp_addds, &mx6_grp_iomux->grp_addds); 598 599 /* Control */ 600 writel(ddr->dram_reset, &mx6_ddr_iomux->dram_reset); 601 writel(ddr->dram_sdba2, &mx6_ddr_iomux->dram_sdba2); 602 writel(ddr->dram_sdcke0, &mx6_ddr_iomux->dram_sdcke0); 603 writel(ddr->dram_sdcke1, &mx6_ddr_iomux->dram_sdcke1); 604 writel(ddr->dram_odt0, &mx6_ddr_iomux->dram_odt0); 605 writel(ddr->dram_odt1, &mx6_ddr_iomux->dram_odt1); 606 writel(grp->grp_ctlds, &mx6_grp_iomux->grp_ctlds); 607 608 /* Data Strobes */ 609 writel(grp->grp_ddrmode_ctl, &mx6_grp_iomux->grp_ddrmode_ctl); 610 writel(ddr->dram_sdqs0, &mx6_ddr_iomux->dram_sdqs0); 611 writel(ddr->dram_sdqs1, &mx6_ddr_iomux->dram_sdqs1); 612 if (width >= 32) { 613 writel(ddr->dram_sdqs2, &mx6_ddr_iomux->dram_sdqs2); 614 writel(ddr->dram_sdqs3, &mx6_ddr_iomux->dram_sdqs3); 615 } 616 617 /* Data */ 618 writel(grp->grp_ddrmode, &mx6_grp_iomux->grp_ddrmode); 619 writel(grp->grp_b0ds, &mx6_grp_iomux->grp_b0ds); 620 writel(grp->grp_b1ds, &mx6_grp_iomux->grp_b1ds); 621 if (width >= 32) { 622 writel(grp->grp_b2ds, &mx6_grp_iomux->grp_b2ds); 623 writel(grp->grp_b3ds, &mx6_grp_iomux->grp_b3ds); 624 } 625 writel(ddr->dram_dqm0, &mx6_ddr_iomux->dram_dqm0); 626 writel(ddr->dram_dqm1, &mx6_ddr_iomux->dram_dqm1); 627 if (width >= 32) { 628 writel(ddr->dram_dqm2, &mx6_ddr_iomux->dram_dqm2); 629 writel(ddr->dram_dqm3, &mx6_ddr_iomux->dram_dqm3); 630 } 631 } 632 #endif 633 634 #if defined(CONFIG_MX6UL) || defined(CONFIG_MX6ULL) 635 void mx6ul_dram_iocfg(unsigned width, 636 const struct mx6ul_iomux_ddr_regs *ddr, 637 const struct mx6ul_iomux_grp_regs *grp) 638 { 639 struct mx6ul_iomux_ddr_regs *mx6_ddr_iomux; 640 struct mx6ul_iomux_grp_regs *mx6_grp_iomux; 641 642 mx6_ddr_iomux = (struct mx6ul_iomux_ddr_regs *)MX6UL_IOM_DDR_BASE; 643 mx6_grp_iomux = (struct mx6ul_iomux_grp_regs *)MX6UL_IOM_GRP_BASE; 644 645 /* DDR IO TYPE */ 646 writel(grp->grp_ddr_type, &mx6_grp_iomux->grp_ddr_type); 647 writel(grp->grp_ddrpke, &mx6_grp_iomux->grp_ddrpke); 648 649 /* CLOCK */ 650 writel(ddr->dram_sdclk_0, &mx6_ddr_iomux->dram_sdclk_0); 651 652 /* ADDRESS */ 653 writel(ddr->dram_cas, &mx6_ddr_iomux->dram_cas); 654 writel(ddr->dram_ras, &mx6_ddr_iomux->dram_ras); 655 writel(grp->grp_addds, &mx6_grp_iomux->grp_addds); 656 657 /* Control */ 658 writel(ddr->dram_reset, &mx6_ddr_iomux->dram_reset); 659 writel(ddr->dram_sdba2, &mx6_ddr_iomux->dram_sdba2); 660 writel(ddr->dram_odt0, &mx6_ddr_iomux->dram_odt0); 661 writel(ddr->dram_odt1, &mx6_ddr_iomux->dram_odt1); 662 writel(grp->grp_ctlds, &mx6_grp_iomux->grp_ctlds); 663 664 /* Data Strobes */ 665 writel(grp->grp_ddrmode_ctl, &mx6_grp_iomux->grp_ddrmode_ctl); 666 writel(ddr->dram_sdqs0, &mx6_ddr_iomux->dram_sdqs0); 667 writel(ddr->dram_sdqs1, &mx6_ddr_iomux->dram_sdqs1); 668 669 /* Data */ 670 writel(grp->grp_ddrmode, &mx6_grp_iomux->grp_ddrmode); 671 writel(grp->grp_b0ds, &mx6_grp_iomux->grp_b0ds); 672 writel(grp->grp_b1ds, &mx6_grp_iomux->grp_b1ds); 673 writel(ddr->dram_dqm0, &mx6_ddr_iomux->dram_dqm0); 674 writel(ddr->dram_dqm1, &mx6_ddr_iomux->dram_dqm1); 675 } 676 #endif 677 678 #if defined(CONFIG_MX6SL) 679 void mx6sl_dram_iocfg(unsigned width, 680 const struct mx6sl_iomux_ddr_regs *ddr, 681 const struct mx6sl_iomux_grp_regs *grp) 682 { 683 struct mx6sl_iomux_ddr_regs *mx6_ddr_iomux; 684 struct mx6sl_iomux_grp_regs *mx6_grp_iomux; 685 686 mx6_ddr_iomux = (struct mx6sl_iomux_ddr_regs *)MX6SL_IOM_DDR_BASE; 687 mx6_grp_iomux = (struct mx6sl_iomux_grp_regs *)MX6SL_IOM_GRP_BASE; 688 689 /* DDR IO TYPE */ 690 mx6_grp_iomux->grp_ddr_type = grp->grp_ddr_type; 691 mx6_grp_iomux->grp_ddrpke = grp->grp_ddrpke; 692 693 /* CLOCK */ 694 mx6_ddr_iomux->dram_sdclk_0 = ddr->dram_sdclk_0; 695 696 /* ADDRESS */ 697 mx6_ddr_iomux->dram_cas = ddr->dram_cas; 698 mx6_ddr_iomux->dram_ras = ddr->dram_ras; 699 mx6_grp_iomux->grp_addds = grp->grp_addds; 700 701 /* Control */ 702 mx6_ddr_iomux->dram_reset = ddr->dram_reset; 703 mx6_ddr_iomux->dram_sdba2 = ddr->dram_sdba2; 704 mx6_grp_iomux->grp_ctlds = grp->grp_ctlds; 705 706 /* Data Strobes */ 707 mx6_grp_iomux->grp_ddrmode_ctl = grp->grp_ddrmode_ctl; 708 mx6_ddr_iomux->dram_sdqs0 = ddr->dram_sdqs0; 709 mx6_ddr_iomux->dram_sdqs1 = ddr->dram_sdqs1; 710 if (width >= 32) { 711 mx6_ddr_iomux->dram_sdqs2 = ddr->dram_sdqs2; 712 mx6_ddr_iomux->dram_sdqs3 = ddr->dram_sdqs3; 713 } 714 715 /* Data */ 716 mx6_grp_iomux->grp_ddrmode = grp->grp_ddrmode; 717 mx6_grp_iomux->grp_b0ds = grp->grp_b0ds; 718 mx6_grp_iomux->grp_b1ds = grp->grp_b1ds; 719 if (width >= 32) { 720 mx6_grp_iomux->grp_b2ds = grp->grp_b2ds; 721 mx6_grp_iomux->grp_b3ds = grp->grp_b3ds; 722 } 723 724 mx6_ddr_iomux->dram_dqm0 = ddr->dram_dqm0; 725 mx6_ddr_iomux->dram_dqm1 = ddr->dram_dqm1; 726 if (width >= 32) { 727 mx6_ddr_iomux->dram_dqm2 = ddr->dram_dqm2; 728 mx6_ddr_iomux->dram_dqm3 = ddr->dram_dqm3; 729 } 730 } 731 #endif 732 733 #if defined(CONFIG_MX6QDL) || defined(CONFIG_MX6Q) || defined(CONFIG_MX6D) 734 /* Configure MX6DQ mmdc iomux */ 735 void mx6dq_dram_iocfg(unsigned width, 736 const struct mx6dq_iomux_ddr_regs *ddr, 737 const struct mx6dq_iomux_grp_regs *grp) 738 { 739 volatile struct mx6dq_iomux_ddr_regs *mx6_ddr_iomux; 740 volatile struct mx6dq_iomux_grp_regs *mx6_grp_iomux; 741 742 mx6_ddr_iomux = (struct mx6dq_iomux_ddr_regs *)MX6DQ_IOM_DDR_BASE; 743 mx6_grp_iomux = (struct mx6dq_iomux_grp_regs *)MX6DQ_IOM_GRP_BASE; 744 745 /* DDR IO Type */ 746 mx6_grp_iomux->grp_ddr_type = grp->grp_ddr_type; 747 mx6_grp_iomux->grp_ddrpke = grp->grp_ddrpke; 748 749 /* Clock */ 750 mx6_ddr_iomux->dram_sdclk_0 = ddr->dram_sdclk_0; 751 mx6_ddr_iomux->dram_sdclk_1 = ddr->dram_sdclk_1; 752 753 /* Address */ 754 mx6_ddr_iomux->dram_cas = ddr->dram_cas; 755 mx6_ddr_iomux->dram_ras = ddr->dram_ras; 756 mx6_grp_iomux->grp_addds = grp->grp_addds; 757 758 /* Control */ 759 mx6_ddr_iomux->dram_reset = ddr->dram_reset; 760 mx6_ddr_iomux->dram_sdcke0 = ddr->dram_sdcke0; 761 mx6_ddr_iomux->dram_sdcke1 = ddr->dram_sdcke1; 762 mx6_ddr_iomux->dram_sdba2 = ddr->dram_sdba2; 763 mx6_ddr_iomux->dram_sdodt0 = ddr->dram_sdodt0; 764 mx6_ddr_iomux->dram_sdodt1 = ddr->dram_sdodt1; 765 mx6_grp_iomux->grp_ctlds = grp->grp_ctlds; 766 767 /* Data Strobes */ 768 mx6_grp_iomux->grp_ddrmode_ctl = grp->grp_ddrmode_ctl; 769 mx6_ddr_iomux->dram_sdqs0 = ddr->dram_sdqs0; 770 mx6_ddr_iomux->dram_sdqs1 = ddr->dram_sdqs1; 771 if (width >= 32) { 772 mx6_ddr_iomux->dram_sdqs2 = ddr->dram_sdqs2; 773 mx6_ddr_iomux->dram_sdqs3 = ddr->dram_sdqs3; 774 } 775 if (width >= 64) { 776 mx6_ddr_iomux->dram_sdqs4 = ddr->dram_sdqs4; 777 mx6_ddr_iomux->dram_sdqs5 = ddr->dram_sdqs5; 778 mx6_ddr_iomux->dram_sdqs6 = ddr->dram_sdqs6; 779 mx6_ddr_iomux->dram_sdqs7 = ddr->dram_sdqs7; 780 } 781 782 /* Data */ 783 mx6_grp_iomux->grp_ddrmode = grp->grp_ddrmode; 784 mx6_grp_iomux->grp_b0ds = grp->grp_b0ds; 785 mx6_grp_iomux->grp_b1ds = grp->grp_b1ds; 786 if (width >= 32) { 787 mx6_grp_iomux->grp_b2ds = grp->grp_b2ds; 788 mx6_grp_iomux->grp_b3ds = grp->grp_b3ds; 789 } 790 if (width >= 64) { 791 mx6_grp_iomux->grp_b4ds = grp->grp_b4ds; 792 mx6_grp_iomux->grp_b5ds = grp->grp_b5ds; 793 mx6_grp_iomux->grp_b6ds = grp->grp_b6ds; 794 mx6_grp_iomux->grp_b7ds = grp->grp_b7ds; 795 } 796 mx6_ddr_iomux->dram_dqm0 = ddr->dram_dqm0; 797 mx6_ddr_iomux->dram_dqm1 = ddr->dram_dqm1; 798 if (width >= 32) { 799 mx6_ddr_iomux->dram_dqm2 = ddr->dram_dqm2; 800 mx6_ddr_iomux->dram_dqm3 = ddr->dram_dqm3; 801 } 802 if (width >= 64) { 803 mx6_ddr_iomux->dram_dqm4 = ddr->dram_dqm4; 804 mx6_ddr_iomux->dram_dqm5 = ddr->dram_dqm5; 805 mx6_ddr_iomux->dram_dqm6 = ddr->dram_dqm6; 806 mx6_ddr_iomux->dram_dqm7 = ddr->dram_dqm7; 807 } 808 } 809 #endif 810 811 #if defined(CONFIG_MX6QDL) || defined(CONFIG_MX6DL) || defined(CONFIG_MX6S) 812 /* Configure MX6SDL mmdc iomux */ 813 void mx6sdl_dram_iocfg(unsigned width, 814 const struct mx6sdl_iomux_ddr_regs *ddr, 815 const struct mx6sdl_iomux_grp_regs *grp) 816 { 817 volatile struct mx6sdl_iomux_ddr_regs *mx6_ddr_iomux; 818 volatile struct mx6sdl_iomux_grp_regs *mx6_grp_iomux; 819 820 mx6_ddr_iomux = (struct mx6sdl_iomux_ddr_regs *)MX6SDL_IOM_DDR_BASE; 821 mx6_grp_iomux = (struct mx6sdl_iomux_grp_regs *)MX6SDL_IOM_GRP_BASE; 822 823 /* DDR IO Type */ 824 mx6_grp_iomux->grp_ddr_type = grp->grp_ddr_type; 825 mx6_grp_iomux->grp_ddrpke = grp->grp_ddrpke; 826 827 /* Clock */ 828 mx6_ddr_iomux->dram_sdclk_0 = ddr->dram_sdclk_0; 829 mx6_ddr_iomux->dram_sdclk_1 = ddr->dram_sdclk_1; 830 831 /* Address */ 832 mx6_ddr_iomux->dram_cas = ddr->dram_cas; 833 mx6_ddr_iomux->dram_ras = ddr->dram_ras; 834 mx6_grp_iomux->grp_addds = grp->grp_addds; 835 836 /* Control */ 837 mx6_ddr_iomux->dram_reset = ddr->dram_reset; 838 mx6_ddr_iomux->dram_sdcke0 = ddr->dram_sdcke0; 839 mx6_ddr_iomux->dram_sdcke1 = ddr->dram_sdcke1; 840 mx6_ddr_iomux->dram_sdba2 = ddr->dram_sdba2; 841 mx6_ddr_iomux->dram_sdodt0 = ddr->dram_sdodt0; 842 mx6_ddr_iomux->dram_sdodt1 = ddr->dram_sdodt1; 843 mx6_grp_iomux->grp_ctlds = grp->grp_ctlds; 844 845 /* Data Strobes */ 846 mx6_grp_iomux->grp_ddrmode_ctl = grp->grp_ddrmode_ctl; 847 mx6_ddr_iomux->dram_sdqs0 = ddr->dram_sdqs0; 848 mx6_ddr_iomux->dram_sdqs1 = ddr->dram_sdqs1; 849 if (width >= 32) { 850 mx6_ddr_iomux->dram_sdqs2 = ddr->dram_sdqs2; 851 mx6_ddr_iomux->dram_sdqs3 = ddr->dram_sdqs3; 852 } 853 if (width >= 64) { 854 mx6_ddr_iomux->dram_sdqs4 = ddr->dram_sdqs4; 855 mx6_ddr_iomux->dram_sdqs5 = ddr->dram_sdqs5; 856 mx6_ddr_iomux->dram_sdqs6 = ddr->dram_sdqs6; 857 mx6_ddr_iomux->dram_sdqs7 = ddr->dram_sdqs7; 858 } 859 860 /* Data */ 861 mx6_grp_iomux->grp_ddrmode = grp->grp_ddrmode; 862 mx6_grp_iomux->grp_b0ds = grp->grp_b0ds; 863 mx6_grp_iomux->grp_b1ds = grp->grp_b1ds; 864 if (width >= 32) { 865 mx6_grp_iomux->grp_b2ds = grp->grp_b2ds; 866 mx6_grp_iomux->grp_b3ds = grp->grp_b3ds; 867 } 868 if (width >= 64) { 869 mx6_grp_iomux->grp_b4ds = grp->grp_b4ds; 870 mx6_grp_iomux->grp_b5ds = grp->grp_b5ds; 871 mx6_grp_iomux->grp_b6ds = grp->grp_b6ds; 872 mx6_grp_iomux->grp_b7ds = grp->grp_b7ds; 873 } 874 mx6_ddr_iomux->dram_dqm0 = ddr->dram_dqm0; 875 mx6_ddr_iomux->dram_dqm1 = ddr->dram_dqm1; 876 if (width >= 32) { 877 mx6_ddr_iomux->dram_dqm2 = ddr->dram_dqm2; 878 mx6_ddr_iomux->dram_dqm3 = ddr->dram_dqm3; 879 } 880 if (width >= 64) { 881 mx6_ddr_iomux->dram_dqm4 = ddr->dram_dqm4; 882 mx6_ddr_iomux->dram_dqm5 = ddr->dram_dqm5; 883 mx6_ddr_iomux->dram_dqm6 = ddr->dram_dqm6; 884 mx6_ddr_iomux->dram_dqm7 = ddr->dram_dqm7; 885 } 886 } 887 #endif 888 889 /* 890 * Configure mx6 mmdc registers based on: 891 * - board-specific memory configuration 892 * - board-specific calibration data 893 * - ddr3/lpddr2 chip details 894 * 895 * The various calculations here are derived from the Freescale 896 * 1. i.Mx6DQSDL DDR3 Script Aid spreadsheet (DOC-94917) designed to generate 897 * MMDC configuration registers based on memory system and memory chip 898 * parameters. 899 * 900 * 2. i.Mx6SL LPDDR2 Script Aid spreadsheet V0.04 designed to generate MMDC 901 * configuration registers based on memory system and memory chip 902 * parameters. 903 * 904 * The defaults here are those which were specified in the spreadsheet. 905 * For details on each register, refer to the IMX6DQRM and/or IMX6SDLRM 906 * and/or IMX6SLRM section titled MMDC initialization. 907 */ 908 #define MR(val, ba, cmd, cs1) \ 909 ((val << 16) | (1 << 15) | (cmd << 4) | (cs1 << 3) | ba) 910 #define MMDC1(entry, value) do { \ 911 if (!is_mx6sx() && !is_mx6ul() && !is_mx6sl()) \ 912 mmdc1->entry = value; \ 913 } while (0) 914 915 /* 916 * According JESD209-2B-LPDDR2: Table 103 917 * WL: write latency 918 */ 919 static int lpddr2_wl(uint32_t mem_speed) 920 { 921 switch (mem_speed) { 922 case 1066: 923 case 933: 924 return 4; 925 case 800: 926 return 3; 927 case 677: 928 case 533: 929 return 2; 930 case 400: 931 case 333: 932 return 1; 933 default: 934 puts("invalid memory speed\n"); 935 hang(); 936 } 937 938 return 0; 939 } 940 941 /* 942 * According JESD209-2B-LPDDR2: Table 103 943 * RL: read latency 944 */ 945 static int lpddr2_rl(uint32_t mem_speed) 946 { 947 switch (mem_speed) { 948 case 1066: 949 return 8; 950 case 933: 951 return 7; 952 case 800: 953 return 6; 954 case 677: 955 return 5; 956 case 533: 957 return 4; 958 case 400: 959 case 333: 960 return 3; 961 default: 962 puts("invalid memory speed\n"); 963 hang(); 964 } 965 966 return 0; 967 } 968 969 void mx6_lpddr2_cfg(const struct mx6_ddr_sysinfo *sysinfo, 970 const struct mx6_mmdc_calibration *calib, 971 const struct mx6_lpddr2_cfg *lpddr2_cfg) 972 { 973 volatile struct mmdc_p_regs *mmdc0; 974 u32 val; 975 u8 tcke, tcksrx, tcksre, trrd; 976 u8 twl, txp, tfaw, tcl; 977 u16 tras, twr, tmrd, trtp, twtr, trfc, txsr; 978 u16 trcd_lp, trppb_lp, trpab_lp, trc_lp; 979 u16 cs0_end; 980 u8 coladdr; 981 int clkper; /* clock period in picoseconds */ 982 int clock; /* clock freq in mHz */ 983 int cs; 984 985 /* only support 16/32 bits */ 986 if (sysinfo->dsize > 1) 987 hang(); 988 989 mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR; 990 991 clock = mxc_get_clock(MXC_DDR_CLK) / 1000000U; 992 clkper = (1000 * 1000) / clock; /* pico seconds */ 993 994 twl = lpddr2_wl(lpddr2_cfg->mem_speed) - 1; 995 996 /* LPDDR2-S2 and LPDDR2-S4 have the same tRFC value. */ 997 switch (lpddr2_cfg->density) { 998 case 1: 999 case 2: 1000 case 4: 1001 trfc = DIV_ROUND_UP(130000, clkper) - 1; 1002 txsr = DIV_ROUND_UP(140000, clkper) - 1; 1003 break; 1004 case 8: 1005 trfc = DIV_ROUND_UP(210000, clkper) - 1; 1006 txsr = DIV_ROUND_UP(220000, clkper) - 1; 1007 break; 1008 default: 1009 /* 1010 * 64Mb, 128Mb, 256Mb, 512Mb are not supported currently. 1011 */ 1012 hang(); 1013 break; 1014 } 1015 /* 1016 * txpdll, txpr, taonpd and taofpd are not relevant in LPDDR2 mode, 1017 * set them to 0. */ 1018 txp = DIV_ROUND_UP(7500, clkper) - 1; 1019 tcke = 3; 1020 if (lpddr2_cfg->mem_speed == 333) 1021 tfaw = DIV_ROUND_UP(60000, clkper) - 1; 1022 else 1023 tfaw = DIV_ROUND_UP(50000, clkper) - 1; 1024 trrd = DIV_ROUND_UP(10000, clkper) - 1; 1025 1026 /* tckesr for LPDDR2 */ 1027 tcksre = DIV_ROUND_UP(15000, clkper); 1028 tcksrx = tcksre; 1029 twr = DIV_ROUND_UP(15000, clkper) - 1; 1030 /* 1031 * tMRR: 2, tMRW: 5 1032 * tMRD should be set to max(tMRR, tMRW) 1033 */ 1034 tmrd = 5; 1035 tras = DIV_ROUND_UP(lpddr2_cfg->trasmin, clkper / 10) - 1; 1036 /* LPDDR2 mode use tRCD_LP filed in MDCFG3. */ 1037 trcd_lp = DIV_ROUND_UP(lpddr2_cfg->trcd_lp, clkper / 10) - 1; 1038 trc_lp = DIV_ROUND_UP(lpddr2_cfg->trasmin + lpddr2_cfg->trppb_lp, 1039 clkper / 10) - 1; 1040 trppb_lp = DIV_ROUND_UP(lpddr2_cfg->trppb_lp, clkper / 10) - 1; 1041 trpab_lp = DIV_ROUND_UP(lpddr2_cfg->trpab_lp, clkper / 10) - 1; 1042 /* To LPDDR2, CL in MDCFG0 refers to RL */ 1043 tcl = lpddr2_rl(lpddr2_cfg->mem_speed) - 3; 1044 twtr = DIV_ROUND_UP(7500, clkper) - 1; 1045 trtp = DIV_ROUND_UP(7500, clkper) - 1; 1046 1047 cs0_end = 4 * sysinfo->cs_density - 1; 1048 1049 debug("density:%d Gb (%d Gb per chip)\n", 1050 sysinfo->cs_density, lpddr2_cfg->density); 1051 debug("clock: %dMHz (%d ps)\n", clock, clkper); 1052 debug("memspd:%d\n", lpddr2_cfg->mem_speed); 1053 debug("trcd_lp=%d\n", trcd_lp); 1054 debug("trppb_lp=%d\n", trppb_lp); 1055 debug("trpab_lp=%d\n", trpab_lp); 1056 debug("trc_lp=%d\n", trc_lp); 1057 debug("tcke=%d\n", tcke); 1058 debug("tcksrx=%d\n", tcksrx); 1059 debug("tcksre=%d\n", tcksre); 1060 debug("trfc=%d\n", trfc); 1061 debug("txsr=%d\n", txsr); 1062 debug("txp=%d\n", txp); 1063 debug("tfaw=%d\n", tfaw); 1064 debug("tcl=%d\n", tcl); 1065 debug("tras=%d\n", tras); 1066 debug("twr=%d\n", twr); 1067 debug("tmrd=%d\n", tmrd); 1068 debug("twl=%d\n", twl); 1069 debug("trtp=%d\n", trtp); 1070 debug("twtr=%d\n", twtr); 1071 debug("trrd=%d\n", trrd); 1072 debug("cs0_end=%d\n", cs0_end); 1073 debug("ncs=%d\n", sysinfo->ncs); 1074 1075 /* 1076 * board-specific configuration: 1077 * These values are determined empirically and vary per board layout 1078 */ 1079 mmdc0->mpwldectrl0 = calib->p0_mpwldectrl0; 1080 mmdc0->mpwldectrl1 = calib->p0_mpwldectrl1; 1081 mmdc0->mpdgctrl0 = calib->p0_mpdgctrl0; 1082 mmdc0->mpdgctrl1 = calib->p0_mpdgctrl1; 1083 mmdc0->mprddlctl = calib->p0_mprddlctl; 1084 mmdc0->mpwrdlctl = calib->p0_mpwrdlctl; 1085 mmdc0->mpzqlp2ctl = calib->mpzqlp2ctl; 1086 1087 /* Read data DQ Byte0-3 delay */ 1088 mmdc0->mprddqby0dl = 0x33333333; 1089 mmdc0->mprddqby1dl = 0x33333333; 1090 if (sysinfo->dsize > 0) { 1091 mmdc0->mprddqby2dl = 0x33333333; 1092 mmdc0->mprddqby3dl = 0x33333333; 1093 } 1094 1095 /* Write data DQ Byte0-3 delay */ 1096 mmdc0->mpwrdqby0dl = 0xf3333333; 1097 mmdc0->mpwrdqby1dl = 0xf3333333; 1098 if (sysinfo->dsize > 0) { 1099 mmdc0->mpwrdqby2dl = 0xf3333333; 1100 mmdc0->mpwrdqby3dl = 0xf3333333; 1101 } 1102 1103 /* 1104 * In LPDDR2 mode this register should be cleared, 1105 * so no termination will be activated. 1106 */ 1107 mmdc0->mpodtctrl = 0; 1108 1109 /* complete calibration */ 1110 val = (1 << 11); /* Force measurement on delay-lines */ 1111 mmdc0->mpmur0 = val; 1112 1113 /* Step 1: configuration request */ 1114 mmdc0->mdscr = (u32)(1 << 15); /* config request */ 1115 1116 /* Step 2: Timing configuration */ 1117 mmdc0->mdcfg0 = (trfc << 24) | (txsr << 16) | (txp << 13) | 1118 (tfaw << 4) | tcl; 1119 mmdc0->mdcfg1 = (tras << 16) | (twr << 9) | (tmrd << 5) | twl; 1120 mmdc0->mdcfg2 = (trtp << 6) | (twtr << 3) | trrd; 1121 mmdc0->mdcfg3lp = (trc_lp << 16) | (trcd_lp << 8) | 1122 (trppb_lp << 4) | trpab_lp; 1123 mmdc0->mdotc = 0; 1124 1125 mmdc0->mdasp = cs0_end; /* CS addressing */ 1126 1127 /* Step 3: Configure DDR type */ 1128 mmdc0->mdmisc = (sysinfo->cs1_mirror << 19) | (sysinfo->walat << 16) | 1129 (sysinfo->bi_on << 12) | (sysinfo->mif3_mode << 9) | 1130 (sysinfo->ralat << 6) | (1 << 3); 1131 1132 /* Step 4: Configure delay while leaving reset */ 1133 mmdc0->mdor = (sysinfo->sde_to_rst << 8) | 1134 (sysinfo->rst_to_cke << 0); 1135 1136 /* Step 5: Configure DDR physical parameters (density and burst len) */ 1137 coladdr = lpddr2_cfg->coladdr; 1138 if (lpddr2_cfg->coladdr == 8) /* 8-bit COL is 0x3 */ 1139 coladdr += 4; 1140 else if (lpddr2_cfg->coladdr == 12) /* 12-bit COL is 0x4 */ 1141 coladdr += 1; 1142 mmdc0->mdctl = (lpddr2_cfg->rowaddr - 11) << 24 | /* ROW */ 1143 (coladdr - 9) << 20 | /* COL */ 1144 (0 << 19) | /* Burst Length = 4 for LPDDR2 */ 1145 (sysinfo->dsize << 16); /* DDR data bus size */ 1146 1147 /* Step 6: Perform ZQ calibration */ 1148 val = 0xa1390003; /* one-time HW ZQ calib */ 1149 mmdc0->mpzqhwctrl = val; 1150 1151 /* Step 7: Enable MMDC with desired chip select */ 1152 mmdc0->mdctl |= (1 << 31) | /* SDE_0 for CS0 */ 1153 ((sysinfo->ncs == 2) ? 1 : 0) << 30; /* SDE_1 for CS1 */ 1154 1155 /* Step 8: Write Mode Registers to Init LPDDR2 devices */ 1156 for (cs = 0; cs < sysinfo->ncs; cs++) { 1157 /* MR63: reset */ 1158 mmdc0->mdscr = MR(63, 0, 3, cs); 1159 /* MR10: calibration, 1160 * 0xff is calibration command after intilization. 1161 */ 1162 val = 0xA | (0xff << 8); 1163 mmdc0->mdscr = MR(val, 0, 3, cs); 1164 /* MR1 */ 1165 val = 0x1 | (0x82 << 8); 1166 mmdc0->mdscr = MR(val, 0, 3, cs); 1167 /* MR2 */ 1168 val = 0x2 | (0x04 << 8); 1169 mmdc0->mdscr = MR(val, 0, 3, cs); 1170 /* MR3 */ 1171 val = 0x3 | (0x02 << 8); 1172 mmdc0->mdscr = MR(val, 0, 3, cs); 1173 } 1174 1175 /* Step 10: Power down control and self-refresh */ 1176 mmdc0->mdpdc = (tcke & 0x7) << 16 | 1177 5 << 12 | /* PWDT_1: 256 cycles */ 1178 5 << 8 | /* PWDT_0: 256 cycles */ 1179 1 << 6 | /* BOTH_CS_PD */ 1180 (tcksrx & 0x7) << 3 | 1181 (tcksre & 0x7); 1182 mmdc0->mapsr = 0x00001006; /* ADOPT power down enabled */ 1183 1184 /* Step 11: Configure ZQ calibration: one-time and periodic 1ms */ 1185 val = 0xa1310003; 1186 mmdc0->mpzqhwctrl = val; 1187 1188 /* Step 12: Configure and activate periodic refresh */ 1189 mmdc0->mdref = (sysinfo->refsel << 14) | (sysinfo->refr << 11); 1190 1191 /* Step 13: Deassert config request - init complete */ 1192 mmdc0->mdscr = 0x00000000; 1193 1194 /* wait for auto-ZQ calibration to complete */ 1195 mdelay(1); 1196 } 1197 1198 void mx6_ddr3_cfg(const struct mx6_ddr_sysinfo *sysinfo, 1199 const struct mx6_mmdc_calibration *calib, 1200 const struct mx6_ddr3_cfg *ddr3_cfg) 1201 { 1202 volatile struct mmdc_p_regs *mmdc0; 1203 volatile struct mmdc_p_regs *mmdc1; 1204 u32 val; 1205 u8 tcke, tcksrx, tcksre, txpdll, taofpd, taonpd, trrd; 1206 u8 todtlon, taxpd, tanpd, tcwl, txp, tfaw, tcl; 1207 u8 todt_idle_off = 0x4; /* from DDR3 Script Aid spreadsheet */ 1208 u16 trcd, trc, tras, twr, tmrd, trtp, trp, twtr, trfc, txs, txpr; 1209 u16 cs0_end; 1210 u16 tdllk = 0x1ff; /* DLL locking time: 512 cycles (JEDEC DDR3) */ 1211 u8 coladdr; 1212 int clkper; /* clock period in picoseconds */ 1213 int clock; /* clock freq in MHz */ 1214 int cs; 1215 u16 mem_speed = ddr3_cfg->mem_speed; 1216 1217 mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR; 1218 if (!is_mx6sx() && !is_mx6ul() && !is_mx6sl()) 1219 mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR; 1220 1221 /* Limit mem_speed for MX6D/MX6Q */ 1222 if (is_mx6dq() || is_mx6dqp()) { 1223 if (mem_speed > 1066) 1224 mem_speed = 1066; /* 1066 MT/s */ 1225 1226 tcwl = 4; 1227 } 1228 /* Limit mem_speed for MX6S/MX6DL */ 1229 else { 1230 if (mem_speed > 800) 1231 mem_speed = 800; /* 800 MT/s */ 1232 1233 tcwl = 3; 1234 } 1235 1236 clock = mem_speed / 2; 1237 /* 1238 * Data rate of 1066 MT/s requires 533 MHz DDR3 clock, but MX6D/Q supports 1239 * up to 528 MHz, so reduce the clock to fit chip specs 1240 */ 1241 if (is_mx6dq() || is_mx6dqp()) { 1242 if (clock > 528) 1243 clock = 528; /* 528 MHz */ 1244 } 1245 1246 clkper = (1000 * 1000) / clock; /* pico seconds */ 1247 todtlon = tcwl; 1248 taxpd = tcwl; 1249 tanpd = tcwl; 1250 1251 switch (ddr3_cfg->density) { 1252 case 1: /* 1Gb per chip */ 1253 trfc = DIV_ROUND_UP(110000, clkper) - 1; 1254 txs = DIV_ROUND_UP(120000, clkper) - 1; 1255 break; 1256 case 2: /* 2Gb per chip */ 1257 trfc = DIV_ROUND_UP(160000, clkper) - 1; 1258 txs = DIV_ROUND_UP(170000, clkper) - 1; 1259 break; 1260 case 4: /* 4Gb per chip */ 1261 trfc = DIV_ROUND_UP(260000, clkper) - 1; 1262 txs = DIV_ROUND_UP(270000, clkper) - 1; 1263 break; 1264 case 8: /* 8Gb per chip */ 1265 trfc = DIV_ROUND_UP(350000, clkper) - 1; 1266 txs = DIV_ROUND_UP(360000, clkper) - 1; 1267 break; 1268 default: 1269 /* invalid density */ 1270 puts("invalid chip density\n"); 1271 hang(); 1272 break; 1273 } 1274 txpr = txs; 1275 1276 switch (mem_speed) { 1277 case 800: 1278 txp = DIV_ROUND_UP(max(3 * clkper, 7500), clkper) - 1; 1279 tcke = DIV_ROUND_UP(max(3 * clkper, 7500), clkper) - 1; 1280 if (ddr3_cfg->pagesz == 1) { 1281 tfaw = DIV_ROUND_UP(40000, clkper) - 1; 1282 trrd = DIV_ROUND_UP(max(4 * clkper, 10000), clkper) - 1; 1283 } else { 1284 tfaw = DIV_ROUND_UP(50000, clkper) - 1; 1285 trrd = DIV_ROUND_UP(max(4 * clkper, 10000), clkper) - 1; 1286 } 1287 break; 1288 case 1066: 1289 txp = DIV_ROUND_UP(max(3 * clkper, 7500), clkper) - 1; 1290 tcke = DIV_ROUND_UP(max(3 * clkper, 5625), clkper) - 1; 1291 if (ddr3_cfg->pagesz == 1) { 1292 tfaw = DIV_ROUND_UP(37500, clkper) - 1; 1293 trrd = DIV_ROUND_UP(max(4 * clkper, 7500), clkper) - 1; 1294 } else { 1295 tfaw = DIV_ROUND_UP(50000, clkper) - 1; 1296 trrd = DIV_ROUND_UP(max(4 * clkper, 10000), clkper) - 1; 1297 } 1298 break; 1299 default: 1300 puts("invalid memory speed\n"); 1301 hang(); 1302 break; 1303 } 1304 txpdll = DIV_ROUND_UP(max(10 * clkper, 24000), clkper) - 1; 1305 tcksre = DIV_ROUND_UP(max(5 * clkper, 10000), clkper); 1306 taonpd = DIV_ROUND_UP(2000, clkper) - 1; 1307 tcksrx = tcksre; 1308 taofpd = taonpd; 1309 twr = DIV_ROUND_UP(15000, clkper) - 1; 1310 tmrd = DIV_ROUND_UP(max(12 * clkper, 15000), clkper) - 1; 1311 trc = DIV_ROUND_UP(ddr3_cfg->trcmin, clkper / 10) - 1; 1312 tras = DIV_ROUND_UP(ddr3_cfg->trasmin, clkper / 10) - 1; 1313 tcl = DIV_ROUND_UP(ddr3_cfg->trcd, clkper / 10) - 3; 1314 trp = DIV_ROUND_UP(ddr3_cfg->trcd, clkper / 10) - 1; 1315 twtr = ROUND(max(4 * clkper, 7500) / clkper, 1) - 1; 1316 trcd = trp; 1317 trtp = twtr; 1318 cs0_end = 4 * sysinfo->cs_density - 1; 1319 1320 debug("density:%d Gb (%d Gb per chip)\n", 1321 sysinfo->cs_density, ddr3_cfg->density); 1322 debug("clock: %dMHz (%d ps)\n", clock, clkper); 1323 debug("memspd:%d\n", mem_speed); 1324 debug("tcke=%d\n", tcke); 1325 debug("tcksrx=%d\n", tcksrx); 1326 debug("tcksre=%d\n", tcksre); 1327 debug("taofpd=%d\n", taofpd); 1328 debug("taonpd=%d\n", taonpd); 1329 debug("todtlon=%d\n", todtlon); 1330 debug("tanpd=%d\n", tanpd); 1331 debug("taxpd=%d\n", taxpd); 1332 debug("trfc=%d\n", trfc); 1333 debug("txs=%d\n", txs); 1334 debug("txp=%d\n", txp); 1335 debug("txpdll=%d\n", txpdll); 1336 debug("tfaw=%d\n", tfaw); 1337 debug("tcl=%d\n", tcl); 1338 debug("trcd=%d\n", trcd); 1339 debug("trp=%d\n", trp); 1340 debug("trc=%d\n", trc); 1341 debug("tras=%d\n", tras); 1342 debug("twr=%d\n", twr); 1343 debug("tmrd=%d\n", tmrd); 1344 debug("tcwl=%d\n", tcwl); 1345 debug("tdllk=%d\n", tdllk); 1346 debug("trtp=%d\n", trtp); 1347 debug("twtr=%d\n", twtr); 1348 debug("trrd=%d\n", trrd); 1349 debug("txpr=%d\n", txpr); 1350 debug("cs0_end=%d\n", cs0_end); 1351 debug("ncs=%d\n", sysinfo->ncs); 1352 debug("Rtt_wr=%d\n", sysinfo->rtt_wr); 1353 debug("Rtt_nom=%d\n", sysinfo->rtt_nom); 1354 debug("SRT=%d\n", ddr3_cfg->SRT); 1355 debug("twr=%d\n", twr); 1356 1357 /* 1358 * board-specific configuration: 1359 * These values are determined empirically and vary per board layout 1360 * see: 1361 * appnote, ddr3 spreadsheet 1362 */ 1363 mmdc0->mpwldectrl0 = calib->p0_mpwldectrl0; 1364 mmdc0->mpwldectrl1 = calib->p0_mpwldectrl1; 1365 mmdc0->mpdgctrl0 = calib->p0_mpdgctrl0; 1366 mmdc0->mpdgctrl1 = calib->p0_mpdgctrl1; 1367 mmdc0->mprddlctl = calib->p0_mprddlctl; 1368 mmdc0->mpwrdlctl = calib->p0_mpwrdlctl; 1369 if (sysinfo->dsize > 1) { 1370 MMDC1(mpwldectrl0, calib->p1_mpwldectrl0); 1371 MMDC1(mpwldectrl1, calib->p1_mpwldectrl1); 1372 MMDC1(mpdgctrl0, calib->p1_mpdgctrl0); 1373 MMDC1(mpdgctrl1, calib->p1_mpdgctrl1); 1374 MMDC1(mprddlctl, calib->p1_mprddlctl); 1375 MMDC1(mpwrdlctl, calib->p1_mpwrdlctl); 1376 } 1377 1378 /* Read data DQ Byte0-3 delay */ 1379 mmdc0->mprddqby0dl = 0x33333333; 1380 mmdc0->mprddqby1dl = 0x33333333; 1381 if (sysinfo->dsize > 0) { 1382 mmdc0->mprddqby2dl = 0x33333333; 1383 mmdc0->mprddqby3dl = 0x33333333; 1384 } 1385 1386 if (sysinfo->dsize > 1) { 1387 MMDC1(mprddqby0dl, 0x33333333); 1388 MMDC1(mprddqby1dl, 0x33333333); 1389 MMDC1(mprddqby2dl, 0x33333333); 1390 MMDC1(mprddqby3dl, 0x33333333); 1391 } 1392 1393 /* MMDC Termination: rtt_nom:2 RZQ/2(120ohm), rtt_nom:1 RZQ/4(60ohm) */ 1394 val = (sysinfo->rtt_nom == 2) ? 0x00011117 : 0x00022227; 1395 mmdc0->mpodtctrl = val; 1396 if (sysinfo->dsize > 1) 1397 MMDC1(mpodtctrl, val); 1398 1399 /* complete calibration */ 1400 val = (1 << 11); /* Force measurement on delay-lines */ 1401 mmdc0->mpmur0 = val; 1402 if (sysinfo->dsize > 1) 1403 MMDC1(mpmur0, val); 1404 1405 /* Step 1: configuration request */ 1406 mmdc0->mdscr = (u32)(1 << 15); /* config request */ 1407 1408 /* Step 2: Timing configuration */ 1409 mmdc0->mdcfg0 = (trfc << 24) | (txs << 16) | (txp << 13) | 1410 (txpdll << 9) | (tfaw << 4) | tcl; 1411 mmdc0->mdcfg1 = (trcd << 29) | (trp << 26) | (trc << 21) | 1412 (tras << 16) | (1 << 15) /* trpa */ | 1413 (twr << 9) | (tmrd << 5) | tcwl; 1414 mmdc0->mdcfg2 = (tdllk << 16) | (trtp << 6) | (twtr << 3) | trrd; 1415 mmdc0->mdotc = (taofpd << 27) | (taonpd << 24) | (tanpd << 20) | 1416 (taxpd << 16) | (todtlon << 12) | (todt_idle_off << 4); 1417 mmdc0->mdasp = cs0_end; /* CS addressing */ 1418 1419 /* Step 3: Configure DDR type */ 1420 mmdc0->mdmisc = (sysinfo->cs1_mirror << 19) | (sysinfo->walat << 16) | 1421 (sysinfo->bi_on << 12) | (sysinfo->mif3_mode << 9) | 1422 (sysinfo->ralat << 6); 1423 1424 /* Step 4: Configure delay while leaving reset */ 1425 mmdc0->mdor = (txpr << 16) | (sysinfo->sde_to_rst << 8) | 1426 (sysinfo->rst_to_cke << 0); 1427 1428 /* Step 5: Configure DDR physical parameters (density and burst len) */ 1429 coladdr = ddr3_cfg->coladdr; 1430 if (ddr3_cfg->coladdr == 8) /* 8-bit COL is 0x3 */ 1431 coladdr += 4; 1432 else if (ddr3_cfg->coladdr == 12) /* 12-bit COL is 0x4 */ 1433 coladdr += 1; 1434 mmdc0->mdctl = (ddr3_cfg->rowaddr - 11) << 24 | /* ROW */ 1435 (coladdr - 9) << 20 | /* COL */ 1436 (1 << 19) | /* Burst Length = 8 for DDR3 */ 1437 (sysinfo->dsize << 16); /* DDR data bus size */ 1438 1439 /* Step 6: Perform ZQ calibration */ 1440 val = 0xa1390001; /* one-time HW ZQ calib */ 1441 mmdc0->mpzqhwctrl = val; 1442 if (sysinfo->dsize > 1) 1443 MMDC1(mpzqhwctrl, val); 1444 1445 /* Step 7: Enable MMDC with desired chip select */ 1446 mmdc0->mdctl |= (1 << 31) | /* SDE_0 for CS0 */ 1447 ((sysinfo->ncs == 2) ? 1 : 0) << 30; /* SDE_1 for CS1 */ 1448 1449 /* Step 8: Write Mode Registers to Init DDR3 devices */ 1450 for (cs = 0; cs < sysinfo->ncs; cs++) { 1451 /* MR2 */ 1452 val = (sysinfo->rtt_wr & 3) << 9 | (ddr3_cfg->SRT & 1) << 7 | 1453 ((tcwl - 3) & 3) << 3; 1454 debug("MR2 CS%d: 0x%08x\n", cs, (u32)MR(val, 2, 3, cs)); 1455 mmdc0->mdscr = MR(val, 2, 3, cs); 1456 /* MR3 */ 1457 debug("MR3 CS%d: 0x%08x\n", cs, (u32)MR(0, 3, 3, cs)); 1458 mmdc0->mdscr = MR(0, 3, 3, cs); 1459 /* MR1 */ 1460 val = ((sysinfo->rtt_nom & 1) ? 1 : 0) << 2 | 1461 ((sysinfo->rtt_nom & 2) ? 1 : 0) << 6; 1462 debug("MR1 CS%d: 0x%08x\n", cs, (u32)MR(val, 1, 3, cs)); 1463 mmdc0->mdscr = MR(val, 1, 3, cs); 1464 /* MR0 */ 1465 val = ((tcl - 1) << 4) | /* CAS */ 1466 (1 << 8) | /* DLL Reset */ 1467 ((twr - 3) << 9) | /* Write Recovery */ 1468 (sysinfo->pd_fast_exit << 12); /* Precharge PD PLL on */ 1469 debug("MR0 CS%d: 0x%08x\n", cs, (u32)MR(val, 0, 3, cs)); 1470 mmdc0->mdscr = MR(val, 0, 3, cs); 1471 /* ZQ calibration */ 1472 val = (1 << 10); 1473 mmdc0->mdscr = MR(val, 0, 4, cs); 1474 } 1475 1476 /* Step 10: Power down control and self-refresh */ 1477 mmdc0->mdpdc = (tcke & 0x7) << 16 | 1478 5 << 12 | /* PWDT_1: 256 cycles */ 1479 5 << 8 | /* PWDT_0: 256 cycles */ 1480 1 << 6 | /* BOTH_CS_PD */ 1481 (tcksrx & 0x7) << 3 | 1482 (tcksre & 0x7); 1483 if (!sysinfo->pd_fast_exit) 1484 mmdc0->mdpdc |= (1 << 7); /* SLOW_PD */ 1485 mmdc0->mapsr = 0x00001006; /* ADOPT power down enabled */ 1486 1487 /* Step 11: Configure ZQ calibration: one-time and periodic 1ms */ 1488 val = 0xa1390003; 1489 mmdc0->mpzqhwctrl = val; 1490 if (sysinfo->dsize > 1) 1491 MMDC1(mpzqhwctrl, val); 1492 1493 /* Step 12: Configure and activate periodic refresh */ 1494 mmdc0->mdref = (sysinfo->refsel << 14) | (sysinfo->refr << 11); 1495 1496 /* Step 13: Deassert config request - init complete */ 1497 mmdc0->mdscr = 0x00000000; 1498 1499 /* wait for auto-ZQ calibration to complete */ 1500 mdelay(1); 1501 } 1502 1503 void mmdc_read_calibration(struct mx6_ddr_sysinfo const *sysinfo, 1504 struct mx6_mmdc_calibration *calib) 1505 { 1506 struct mmdc_p_regs *mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR; 1507 struct mmdc_p_regs *mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR; 1508 1509 calib->p0_mpwldectrl0 = readl(&mmdc0->mpwldectrl0); 1510 calib->p0_mpwldectrl1 = readl(&mmdc0->mpwldectrl1); 1511 calib->p0_mpdgctrl0 = readl(&mmdc0->mpdgctrl0); 1512 calib->p0_mpdgctrl1 = readl(&mmdc0->mpdgctrl1); 1513 calib->p0_mprddlctl = readl(&mmdc0->mprddlctl); 1514 calib->p0_mpwrdlctl = readl(&mmdc0->mpwrdlctl); 1515 1516 if (sysinfo->dsize == 2) { 1517 calib->p1_mpwldectrl0 = readl(&mmdc1->mpwldectrl0); 1518 calib->p1_mpwldectrl1 = readl(&mmdc1->mpwldectrl1); 1519 calib->p1_mpdgctrl0 = readl(&mmdc1->mpdgctrl0); 1520 calib->p1_mpdgctrl1 = readl(&mmdc1->mpdgctrl1); 1521 calib->p1_mprddlctl = readl(&mmdc1->mprddlctl); 1522 calib->p1_mpwrdlctl = readl(&mmdc1->mpwrdlctl); 1523 } 1524 } 1525 1526 void mx6_dram_cfg(const struct mx6_ddr_sysinfo *sysinfo, 1527 const struct mx6_mmdc_calibration *calib, 1528 const void *ddr_cfg) 1529 { 1530 if (sysinfo->ddr_type == DDR_TYPE_DDR3) { 1531 mx6_ddr3_cfg(sysinfo, calib, ddr_cfg); 1532 } else if (sysinfo->ddr_type == DDR_TYPE_LPDDR2) { 1533 mx6_lpddr2_cfg(sysinfo, calib, ddr_cfg); 1534 } else { 1535 puts("Unsupported ddr type\n"); 1536 hang(); 1537 } 1538 } 1539