1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Machine Specific Values for SMDK5250 board based on EXYNOS5 4 * 5 * Copyright (C) 2012 Samsung Electronics 6 */ 7 8 #ifndef _SMDK5250_SETUP_H 9 #define _SMDK5250_SETUP_H 10 11 #include <config.h> 12 #include <asm/arch/dmc.h> 13 14 #define NOT_AVAILABLE 0 15 #define DATA_MASK 0xFFFFF 16 17 #define ENABLE_BIT 0x1 18 #define DISABLE_BIT 0x0 19 #define CA_SWAP_EN (1 << 0) 20 21 /* Set PLL */ 22 #define set_pll(mdiv, pdiv, sdiv) (1<<31 | mdiv<<16 | pdiv<<8 | sdiv) 23 24 /* MEMCONTROL register bit fields */ 25 #define DMC_MEMCONTROL_CLK_STOP_DISABLE (0 << 0) 26 #define DMC_MEMCONTROL_DPWRDN_DISABLE (0 << 1) 27 #define DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE (0 << 2) 28 #define DMC_MEMCONTROL_TP_DISABLE (0 << 4) 29 #define DMC_MEMCONTROL_DSREF_DISABLE (0 << 5) 30 #define DMC_MEMCONTROL_DSREF_ENABLE (1 << 5) 31 #define DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(x) (x << 6) 32 33 #define DMC_MEMCONTROL_MEM_TYPE_LPDDR3 (7 << 8) 34 #define DMC_MEMCONTROL_MEM_TYPE_DDR3 (6 << 8) 35 #define DMC_MEMCONTROL_MEM_TYPE_LPDDR2 (5 << 8) 36 37 #define DMC_MEMCONTROL_MEM_WIDTH_32BIT (2 << 12) 38 39 #define DMC_MEMCONTROL_NUM_CHIP_1 (0 << 16) 40 #define DMC_MEMCONTROL_NUM_CHIP_2 (1 << 16) 41 42 #define DMC_MEMCONTROL_BL_8 (3 << 20) 43 #define DMC_MEMCONTROL_BL_4 (2 << 20) 44 45 #define DMC_MEMCONTROL_PZQ_DISABLE (0 << 24) 46 47 #define DMC_MEMCONTROL_MRR_BYTE_7_0 (0 << 25) 48 #define DMC_MEMCONTROL_MRR_BYTE_15_8 (1 << 25) 49 #define DMC_MEMCONTROL_MRR_BYTE_23_16 (2 << 25) 50 #define DMC_MEMCONTROL_MRR_BYTE_31_24 (3 << 25) 51 52 /* MEMCONFIG0 register bit fields */ 53 #define DMC_MEMCONFIGX_CHIP_MAP_INTERLEAVED (1 << 12) 54 #define DMC_MEMCONFIG_CHIP_MAP_SPLIT (2 << 12) 55 #define DMC_MEMCONFIGX_CHIP_COL_10 (3 << 8) 56 #define DMC_MEMCONFIGX_CHIP_ROW_14 (2 << 4) 57 #define DMC_MEMCONFIGX_CHIP_ROW_15 (3 << 4) 58 #define DMC_MEMCONFIGX_CHIP_BANK_8 (3 << 0) 59 60 #define DMC_MEMBASECONFIGX_CHIP_BASE(x) (x << 16) 61 #define DMC_MEMBASECONFIGX_CHIP_MASK(x) (x << 0) 62 #define DMC_MEMBASECONFIG_VAL(x) ( \ 63 DMC_MEMBASECONFIGX_CHIP_BASE(x) | \ 64 DMC_MEMBASECONFIGX_CHIP_MASK(0x780) \ 65 ) 66 67 /* 68 * As we use channel interleaving, therefore value of the base address 69 * register must be set as half of the bus base address 70 * RAM start addess is 0x2000_0000 which means chip_base is 0x20, so 71 * we need to set half 0x10 to the membaseconfigx registers 72 * see exynos5420 UM section 17.17.3.21 for more. 73 */ 74 #define DMC_CHIP_BASE_0 0x10 75 #define DMC_CHIP_BASE_1 0x50 76 #define DMC_CHIP_MASK 0x7C0 77 78 #define DMC_MEMBASECONFIG0_VAL DMC_MEMBASECONFIG_VAL(0x40) 79 #define DMC_MEMBASECONFIG1_VAL DMC_MEMBASECONFIG_VAL(0x80) 80 81 #define DMC_PRECHCONFIG_VAL 0xFF000000 82 #define DMC_PWRDNCONFIG_VAL 0xFFFF00FF 83 84 #define DMC_CONCONTROL_RESET_VAL 0x0FFF0000 85 #define DFI_INIT_START (1 << 28) 86 #define EMPTY (1 << 8) 87 #define AREF_EN (1 << 5) 88 89 #define DFI_INIT_COMPLETE_CHO (1 << 2) 90 #define DFI_INIT_COMPLETE_CH1 (1 << 3) 91 92 #define RDLVL_COMPLETE_CHO (1 << 14) 93 #define RDLVL_COMPLETE_CH1 (1 << 15) 94 95 #define CLK_STOP_EN (1 << 0) 96 #define DPWRDN_EN (1 << 1) 97 #define DSREF_EN (1 << 5) 98 99 /* COJCONTROL register bit fields */ 100 #define DMC_CONCONTROL_IO_PD_CON_DISABLE (0 << 3) 101 #define DMC_CONCONTROL_IO_PD_CON_ENABLE (1 << 3) 102 #define DMC_CONCONTROL_AREF_EN_DISABLE (0 << 5) 103 #define DMC_CONCONTROL_AREF_EN_ENABLE (1 << 5) 104 #define DMC_CONCONTROL_EMPTY_DISABLE (0 << 8) 105 #define DMC_CONCONTROL_EMPTY_ENABLE (1 << 8) 106 #define DMC_CONCONTROL_RD_FETCH_DISABLE (0x0 << 12) 107 #define DMC_CONCONTROL_TIMEOUT_LEVEL0 (0xFFF << 16) 108 #define DMC_CONCONTROL_DFI_INIT_START_DISABLE (0 << 28) 109 110 #define DMC_CONCONTROL_VAL 0x1FFF2101 111 112 #define DREX_CONCONTROL_VAL DMC_CONCONTROL_VAL \ 113 | DMC_CONCONTROL_AREF_EN_ENABLE \ 114 | DMC_CONCONTROL_IO_PD_CON_ENABLE 115 116 #define DMC_CONCONTROL_IO_PD_CON(x) (x << 6) 117 118 /* CLK_DIV_CPU1 */ 119 #define HPM_RATIO 0x2 120 #define COPY_RATIO 0x0 121 122 /* CLK_DIV_CPU1 = 0x00000003 */ 123 #define CLK_DIV_CPU1_VAL ((HPM_RATIO << 4) \ 124 | (COPY_RATIO)) 125 126 /* CLK_SRC_CORE0 */ 127 #define CLK_SRC_CORE0_VAL 0x00000000 128 129 /* CLK_SRC_CORE1 */ 130 #define CLK_SRC_CORE1_VAL 0x100 131 132 /* CLK_DIV_CORE0 */ 133 #define CLK_DIV_CORE0_VAL 0x00120000 134 135 /* CLK_DIV_CORE1 */ 136 #define CLK_DIV_CORE1_VAL 0x07070700 137 138 /* CLK_DIV_SYSRGT */ 139 #define CLK_DIV_SYSRGT_VAL 0x00000111 140 141 /* CLK_DIV_ACP */ 142 #define CLK_DIV_ACP_VAL 0x12 143 144 /* CLK_DIV_SYSLFT */ 145 #define CLK_DIV_SYSLFT_VAL 0x00000311 146 147 #define MUX_APLL_SEL_MASK (1 << 0) 148 #define MUX_MPLL_SEL_MASK (1 << 8) 149 #define MPLL_SEL_MOUT_MPLLFOUT (2 << 8) 150 #define MUX_CPLL_SEL_MASK (1 << 8) 151 #define MUX_EPLL_SEL_MASK (1 << 12) 152 #define MUX_VPLL_SEL_MASK (1 << 16) 153 #define MUX_GPLL_SEL_MASK (1 << 28) 154 #define MUX_BPLL_SEL_MASK (1 << 0) 155 #define MUX_HPM_SEL_MASK (1 << 20) 156 #define HPM_SEL_SCLK_MPLL (1 << 21) 157 #define PLL_LOCKED (1 << 29) 158 #define APLL_CON0_LOCKED (1 << 29) 159 #define MPLL_CON0_LOCKED (1 << 29) 160 #define BPLL_CON0_LOCKED (1 << 29) 161 #define CPLL_CON0_LOCKED (1 << 29) 162 #define EPLL_CON0_LOCKED (1 << 29) 163 #define GPLL_CON0_LOCKED (1 << 29) 164 #define VPLL_CON0_LOCKED (1 << 29) 165 #define CLK_REG_DISABLE 0x0 166 #define TOP2_VAL 0x0110000 167 168 /* SCLK_SRC_ISP - set SPI0/1 to 6 = SCLK_MPLL_USER */ 169 #define SPI0_ISP_SEL 6 170 #define SPI1_ISP_SEL 6 171 #define SCLK_SRC_ISP_VAL (SPI1_ISP_SEL << 4) \ 172 | (SPI0_ISP_SEL << 0) 173 174 /* SCLK_DIV_ISP - set SPI0/1 to 0xf = divide by 16 */ 175 #define SPI0_ISP_RATIO 0xf 176 #define SPI1_ISP_RATIO 0xf 177 #define SCLK_DIV_ISP_VAL (SPI1_ISP_RATIO << 12) \ 178 | (SPI0_ISP_RATIO << 0) 179 180 /* CLK_DIV_FSYS2 */ 181 #define MMC2_RATIO_MASK 0xf 182 #define MMC2_RATIO_VAL 0x3 183 #define MMC2_RATIO_OFFSET 0 184 185 #define MMC2_PRE_RATIO_MASK 0xff 186 #define MMC2_PRE_RATIO_VAL 0x9 187 #define MMC2_PRE_RATIO_OFFSET 8 188 189 #define MMC3_RATIO_MASK 0xf 190 #define MMC3_RATIO_VAL 0x1 191 #define MMC3_RATIO_OFFSET 16 192 193 #define MMC3_PRE_RATIO_MASK 0xff 194 #define MMC3_PRE_RATIO_VAL 0x0 195 #define MMC3_PRE_RATIO_OFFSET 24 196 197 /* CLK_SRC_LEX */ 198 #define CLK_SRC_LEX_VAL 0x0 199 200 /* CLK_DIV_LEX */ 201 #define CLK_DIV_LEX_VAL 0x10 202 203 /* CLK_DIV_R0X */ 204 #define CLK_DIV_R0X_VAL 0x10 205 206 /* CLK_DIV_L0X */ 207 #define CLK_DIV_R1X_VAL 0x10 208 209 /* CLK_DIV_ISP2 */ 210 #define CLK_DIV_ISP2_VAL 0x1 211 212 /* CLK_SRC_KFC */ 213 #define SRC_KFC_HPM_SEL (1 << 15) 214 215 /* CLK_SRC_KFC */ 216 #define CLK_SRC_KFC_VAL 0x00008001 217 218 /* CLK_DIV_KFC */ 219 #define CLK_DIV_KFC_VAL 0x03300110 220 221 /* CLK_DIV2_RATIO */ 222 #define CLK_DIV2_RATIO 0x10111150 223 224 /* CLK_DIV4_RATIO */ 225 #define CLK_DIV4_RATIO 0x00000003 226 227 /* CLK_DIV_G2D */ 228 #define CLK_DIV_G2D 0x00000010 229 230 /* 231 * DIV_DISP1_0 232 * For DP, divisor should be 2 233 */ 234 #define CLK_DIV_DISP1_0_FIMD1 (2 << 0) 235 236 /* CLK_GATE_IP_DISP1 */ 237 #define CLK_GATE_DP1_ALLOW (1 << 4) 238 239 /* AUDIO CLK SEL */ 240 #define AUDIO0_SEL_EPLL (0x6 << 28) 241 #define AUDIO0_RATIO 0x5 242 #define PCM0_RATIO 0x3 243 #define DIV_MAU_VAL (PCM0_RATIO << 24 | AUDIO0_RATIO << 20) 244 245 /* CLK_SRC_CDREX */ 246 #define MUX_MCLK_CDR_MSPLL (1 << 4) 247 #define MUX_BPLL_SEL_FOUTBPLL (1 << 0) 248 #define BPLL_SEL_MASK 0x7 249 #define FOUTBPLL 2 250 251 #define DDR3PHY_CTRL_PHY_RESET (1 << 0) 252 #define DDR3PHY_CTRL_PHY_RESET_OFF (0 << 0) 253 254 #define PHY_CON0_RESET_VAL 0x17020a40 255 #define P0_CMD_EN (1 << 14) 256 #define BYTE_RDLVL_EN (1 << 13) 257 #define CTRL_SHGATE (1 << 8) 258 259 #define PHY_CON1_RESET_VAL 0x09210100 260 #define RDLVL_PASS_ADJ_VAL 0x6 261 #define RDLVL_PASS_ADJ_OFFSET 16 262 #define CTRL_GATEDURADJ_MASK (0xf << 20) 263 #define READ_LEVELLING_DDR3 0x0100 264 265 #define PHY_CON2_RESET_VAL 0x00010004 266 #define INIT_DESKEW_EN (1 << 6) 267 #define DLL_DESKEW_EN (1 << 12) 268 #define RDLVL_GATE_EN (1 << 24) 269 #define RDLVL_EN (1 << 25) 270 #define RDLVL_INCR_ADJ (0x1 << 16) 271 272 /* DREX_PAUSE */ 273 #define DREX_PAUSE_EN (1 << 0) 274 275 #define BYPASS_EN (1 << 22) 276 277 /* MEMMORY VAL */ 278 #define PHY_CON0_VAL 0x17021A00 279 280 #define PHY_CON12_RESET_VAL 0x10100070 281 #define PHY_CON12_VAL 0x10107F50 282 #define CTRL_START (1 << 6) 283 #define CTRL_DLL_ON (1 << 5) 284 #define CTRL_LOCK_COARSE_OFFSET 10 285 #define CTRL_LOCK_COARSE_MASK (0x7F << CTRL_LOCK_COARSE_OFFSET) 286 #define CTRL_LOCK_COARSE(x) (((x) & CTRL_LOCK_COARSE_MASK) >> \ 287 CTRL_LOCK_COARSE_OFFSET) 288 #define CTRL_FORCE_MASK (0x7F << 8) 289 #define CTRL_FINE_LOCKED 0x7 290 291 #define CTRL_OFFSETD_RESET_VAL 0x8 292 #define CTRL_OFFSETD_VAL 0x7F 293 294 #define CTRL_OFFSETR0 0x7F 295 #define CTRL_OFFSETR1 0x7F 296 #define CTRL_OFFSETR2 0x7F 297 #define CTRL_OFFSETR3 0x7F 298 #define PHY_CON4_VAL (CTRL_OFFSETR0 << 0 | \ 299 CTRL_OFFSETR1 << 8 | \ 300 CTRL_OFFSETR2 << 16 | \ 301 CTRL_OFFSETR3 << 24) 302 #define PHY_CON4_RESET_VAL 0x08080808 303 304 #define CTRL_OFFSETW0 0x7F 305 #define CTRL_OFFSETW1 0x7F 306 #define CTRL_OFFSETW2 0x7F 307 #define CTRL_OFFSETW3 0x7F 308 #define PHY_CON6_VAL (CTRL_OFFSETW0 << 0 | \ 309 CTRL_OFFSETW1 << 8 | \ 310 CTRL_OFFSETW2 << 16 | \ 311 CTRL_OFFSETW3 << 24) 312 #define PHY_CON6_RESET_VAL 0x08080808 313 314 #define PHY_CON14_RESET_VAL 0x001F0000 315 #define CTRL_PULLD_DQS 0xF 316 #define CTRL_PULLD_DQS_OFFSET 0 317 318 /* ZQ Configurations */ 319 #define PHY_CON16_RESET_VAL 0x08000304 320 321 #define ZQ_CLK_EN (1 << 27) 322 #define ZQ_CLK_DIV_EN (1 << 18) 323 #define ZQ_MANUAL_STR (1 << 1) 324 #define ZQ_DONE (1 << 0) 325 #define ZQ_MODE_DDS_OFFSET 24 326 327 #define CTRL_RDLVL_GATE_ENABLE 1 328 #define CTRL_RDLVL_GATE_DISABLE 0 329 #define CTRL_RDLVL_DATA_ENABLE 2 330 331 /* Direct Command */ 332 #define DIRECT_CMD_NOP 0x07000000 333 #define DIRECT_CMD_PALL 0x01000000 334 #define DIRECT_CMD_ZQINIT 0x0a000000 335 #define DIRECT_CMD_CHANNEL_SHIFT 28 336 #define DIRECT_CMD_CHIP_SHIFT 20 337 #define DIRECT_CMD_BANK_SHIFT 16 338 #define DIRECT_CMD_REFA (5 << 24) 339 #define DIRECT_CMD_MRS1 0x71C00 340 #define DIRECT_CMD_MRS2 0x10BFC 341 #define DIRECT_CMD_MRS3 0x0050C 342 #define DIRECT_CMD_MRS4 0x00868 343 #define DIRECT_CMD_MRS5 0x00C04 344 345 /* Drive Strength */ 346 #define IMPEDANCE_48_OHM 4 347 #define IMPEDANCE_40_OHM 5 348 #define IMPEDANCE_34_OHM 6 349 #define IMPEDANCE_30_OHM 7 350 #define PHY_CON39_VAL_48_OHM 0x09240924 351 #define PHY_CON39_VAL_40_OHM 0x0B6D0B6D 352 #define PHY_CON39_VAL_34_OHM 0x0DB60DB6 353 #define PHY_CON39_VAL_30_OHM 0x0FFF0FFF 354 355 #define CTRL_BSTLEN_OFFSET 8 356 #define CTRL_RDLAT_OFFSET 0 357 358 #define CMD_DEFAULT_LPDDR3 0xF 359 #define CMD_DEFUALT_OFFSET 0 360 #define T_WRDATA_EN 0x7 361 #define T_WRDATA_EN_DDR3 0x8 362 #define T_WRDATA_EN_OFFSET 16 363 #define T_WRDATA_EN_MASK 0x1f 364 365 #define PHY_CON31_VAL 0x0C183060 366 #define PHY_CON32_VAL 0x60C18306 367 #define PHY_CON33_VAL 0x00000030 368 369 #define PHY_CON31_RESET_VAL 0x0 370 #define PHY_CON32_RESET_VAL 0x0 371 #define PHY_CON33_RESET_VAL 0x0 372 373 #define SL_DLL_DYN_CON_EN (1 << 1) 374 #define FP_RESYNC (1 << 3) 375 #define CTRL_START (1 << 6) 376 377 #define DMC_AREF_EN (1 << 5) 378 #define DMC_CONCONTROL_EMPTY (1 << 8) 379 #define DFI_INIT_START (1 << 28) 380 381 #define DMC_MEMCONTROL_VAL 0x00312700 382 #define CLK_STOP_EN (1 << 0) 383 #define DPWRDN_EN (1 << 1) 384 #define DSREF_EN (1 << 5) 385 386 #define MEMBASECONFIG_CHIP_MASK_VAL 0x7E0 387 #define MEMBASECONFIG_CHIP_MASK_OFFSET 0 388 #define MEMBASECONFIG0_CHIP_BASE_VAL 0x20 389 #define MEMBASECONFIG1_CHIP_BASE_VAL 0x40 390 #define CHIP_BASE_OFFSET 16 391 392 #define MEMCONFIG_VAL 0x1323 393 #define PRECHCONFIG_DEFAULT_VAL 0xFF000000 394 #define PWRDNCONFIG_DEFAULT_VAL 0xFFFF00FF 395 396 #define TIMINGAREF_VAL 0x5d 397 #define TIMINGROW_VAL 0x345A8692 398 #define TIMINGDATA_VAL 0x3630065C 399 #define TIMINGPOWER_VAL 0x50380336 400 #define DFI_INIT_COMPLETE (1 << 3) 401 402 #define BRBRSVCONTROL_VAL 0x00000033 403 #define BRBRSVCONFIG_VAL 0x88778877 404 405 /* Clock Gating Control (CGCONTROL) register */ 406 #define MEMIF_CG_EN (1 << 3) /* Memory interface clock gating */ 407 #define SCG_CG_EN (1 << 2) /* Scheduler clock gating */ 408 #define BUSIF_WR_CG_EN (1 << 1) /* Bus interface write channel clock gating */ 409 #define BUSIF_RD_CG_EN (1 << 0) /* Bus interface read channel clock gating */ 410 #define DMC_INTERNAL_CG (MEMIF_CG_EN | SCG_CG_EN | \ 411 BUSIF_WR_CG_EN | BUSIF_RD_CG_EN) 412 413 /* DMC PHY Control0 register */ 414 #define PHY_CONTROL0_RESET_VAL 0x0 415 #define MEM_TERM_EN (1 << 31) /* Termination enable for memory */ 416 #define PHY_TERM_EN (1 << 30) /* Termination enable for PHY */ 417 #define DMC_CTRL_SHGATE (1 << 29) /* Duration of DQS gating signal */ 418 #define FP_RSYNC (1 << 3) /* Force DLL resyncronization */ 419 420 /* Driver strength for CK, CKE, CS & CA */ 421 #define IMP_OUTPUT_DRV_40_OHM 0x5 422 #define IMP_OUTPUT_DRV_30_OHM 0x7 423 #define DA_3_DS_OFFSET 25 424 #define DA_2_DS_OFFSET 22 425 #define DA_1_DS_OFFSET 19 426 #define DA_0_DS_OFFSET 16 427 #define CA_CK_DRVR_DS_OFFSET 9 428 #define CA_CKE_DRVR_DS_OFFSET 6 429 #define CA_CS_DRVR_DS_OFFSET 3 430 #define CA_ADR_DRVR_DS_OFFSET 0 431 432 #define PHY_CON42_CTRL_BSTLEN_SHIFT 8 433 #define PHY_CON42_CTRL_RDLAT_SHIFT 0 434 435 /* 436 * Definitions that differ with SoC's. 437 * Below is the part defining macros for Exynos5250. 438 * Else part introduces macros for Exynos5420. 439 */ 440 #ifndef CONFIG_EXYNOS5420 441 442 /* APLL_CON1 */ 443 #define APLL_CON1_VAL (0x00203800) 444 445 /* MPLL_CON1 */ 446 #define MPLL_CON1_VAL (0x00203800) 447 448 /* CPLL_CON1 */ 449 #define CPLL_CON1_VAL (0x00203800) 450 451 /* DPLL_CON1 */ 452 #define DPLL_CON1_VAL (NOT_AVAILABLE) 453 454 /* GPLL_CON1 */ 455 #define GPLL_CON1_VAL (0x00203800) 456 457 /* EPLL_CON1, CON2 */ 458 #define EPLL_CON1_VAL 0x00000000 459 #define EPLL_CON2_VAL 0x00000080 460 461 /* VPLL_CON1, CON2 */ 462 #define VPLL_CON1_VAL 0x00000000 463 #define VPLL_CON2_VAL 0x00000080 464 465 /* RPLL_CON1, CON2 */ 466 #define RPLL_CON1_VAL NOT_AVAILABLE 467 #define RPLL_CON2_VAL NOT_AVAILABLE 468 469 /* BPLL_CON1 */ 470 #define BPLL_CON1_VAL 0x00203800 471 472 /* SPLL_CON1 */ 473 #define SPLL_CON1_VAL NOT_AVAILABLE 474 475 /* IPLL_CON1 */ 476 #define IPLL_CON1_VAL NOT_AVAILABLE 477 478 /* KPLL_CON1 */ 479 #define KPLL_CON1_VAL NOT_AVAILABLE 480 481 /* CLK_SRC_ISP */ 482 #define CLK_SRC_ISP_VAL NOT_AVAILABLE 483 #define CLK_DIV_ISP0_VAL 0x31 484 #define CLK_DIV_ISP1_VAL 0x0 485 486 /* CLK_FSYS */ 487 #define CLK_SRC_FSYS0_VAL 0x66666 488 #define CLK_DIV_FSYS0_VAL 0x0BB00000 489 #define CLK_DIV_FSYS1_VAL NOT_AVAILABLE 490 #define CLK_DIV_FSYS2_VAL NOT_AVAILABLE 491 492 /* CLK_SRC_CPU */ 493 /* 0 = MOUTAPLL, 1 = SCLKMPLL */ 494 #define MUX_HPM_SEL 0 495 #define MUX_CPU_SEL 0 496 #define MUX_APLL_SEL 1 497 498 #define CLK_SRC_CPU_VAL ((MUX_HPM_SEL << 20) \ 499 | (MUX_CPU_SEL << 16) \ 500 | (MUX_APLL_SEL)) 501 502 /* CLK_SRC_CDREX */ 503 #define CLK_SRC_CDREX_VAL 0x1 504 505 /* CLK_DIV_CDREX */ 506 #define CLK_DIV_CDREX0_VAL NOT_AVAILABLE 507 #define CLK_DIV_CDREX1_VAL NOT_AVAILABLE 508 509 /* CLK_DIV_CPU0_VAL */ 510 #define CLK_DIV_CPU0_VAL NOT_AVAILABLE 511 512 #define MCLK_CDREX2_RATIO 0x0 513 #define ACLK_EFCON_RATIO 0x1 514 #define MCLK_DPHY_RATIO 0x1 515 #define MCLK_CDREX_RATIO 0x1 516 #define ACLK_C2C_200_RATIO 0x1 517 #define C2C_CLK_400_RATIO 0x1 518 #define PCLK_CDREX_RATIO 0x1 519 #define ACLK_CDREX_RATIO 0x1 520 521 #define CLK_DIV_CDREX_VAL ((MCLK_DPHY_RATIO << 24) \ 522 | (C2C_CLK_400_RATIO << 6) \ 523 | (PCLK_CDREX_RATIO << 4) \ 524 | (ACLK_CDREX_RATIO)) 525 526 /* CLK_SRC_TOP0 */ 527 #define MUX_ACLK_300_GSCL_SEL 0x0 528 #define MUX_ACLK_300_GSCL_MID_SEL 0x0 529 #define MUX_ACLK_400_G3D_MID_SEL 0x0 530 #define MUX_ACLK_333_SEL 0x0 531 #define MUX_ACLK_300_DISP1_SEL 0x0 532 #define MUX_ACLK_300_DISP1_MID_SEL 0x0 533 #define MUX_ACLK_200_SEL 0x0 534 #define MUX_ACLK_166_SEL 0x0 535 #define CLK_SRC_TOP0_VAL ((MUX_ACLK_300_GSCL_SEL << 25) \ 536 | (MUX_ACLK_300_GSCL_MID_SEL << 24) \ 537 | (MUX_ACLK_400_G3D_MID_SEL << 20) \ 538 | (MUX_ACLK_333_SEL << 16) \ 539 | (MUX_ACLK_300_DISP1_SEL << 15) \ 540 | (MUX_ACLK_300_DISP1_MID_SEL << 14) \ 541 | (MUX_ACLK_200_SEL << 12) \ 542 | (MUX_ACLK_166_SEL << 8)) 543 544 /* CLK_SRC_TOP1 */ 545 #define MUX_ACLK_400_G3D_SEL 0x1 546 #define MUX_ACLK_400_ISP_SEL 0x0 547 #define MUX_ACLK_400_IOP_SEL 0x0 548 #define MUX_ACLK_MIPI_HSI_TXBASE_SEL 0x0 549 #define MUX_ACLK_300_GSCL_MID1_SEL 0x0 550 #define MUX_ACLK_300_DISP1_MID1_SEL 0x0 551 #define CLK_SRC_TOP1_VAL ((MUX_ACLK_400_G3D_SEL << 28) \ 552 |(MUX_ACLK_400_ISP_SEL << 24) \ 553 |(MUX_ACLK_400_IOP_SEL << 20) \ 554 |(MUX_ACLK_MIPI_HSI_TXBASE_SEL << 16) \ 555 |(MUX_ACLK_300_GSCL_MID1_SEL << 12) \ 556 |(MUX_ACLK_300_DISP1_MID1_SEL << 8)) 557 558 /* CLK_SRC_TOP2 */ 559 #define MUX_GPLL_SEL 0x1 560 #define MUX_BPLL_USER_SEL 0x0 561 #define MUX_MPLL_USER_SEL 0x0 562 #define MUX_VPLL_SEL 0x1 563 #define MUX_EPLL_SEL 0x1 564 #define MUX_CPLL_SEL 0x1 565 #define VPLLSRC_SEL 0x0 566 #define CLK_SRC_TOP2_VAL ((MUX_GPLL_SEL << 28) \ 567 | (MUX_BPLL_USER_SEL << 24) \ 568 | (MUX_MPLL_USER_SEL << 20) \ 569 | (MUX_VPLL_SEL << 16) \ 570 | (MUX_EPLL_SEL << 12) \ 571 | (MUX_CPLL_SEL << 8) \ 572 | (VPLLSRC_SEL)) 573 /* CLK_SRC_TOP3 */ 574 #define MUX_ACLK_333_SUB_SEL 0x1 575 #define MUX_ACLK_400_SUB_SEL 0x1 576 #define MUX_ACLK_266_ISP_SUB_SEL 0x1 577 #define MUX_ACLK_266_GPS_SUB_SEL 0x0 578 #define MUX_ACLK_300_GSCL_SUB_SEL 0x1 579 #define MUX_ACLK_266_GSCL_SUB_SEL 0x1 580 #define MUX_ACLK_300_DISP1_SUB_SEL 0x1 581 #define MUX_ACLK_200_DISP1_SUB_SEL 0x1 582 #define CLK_SRC_TOP3_VAL ((MUX_ACLK_333_SUB_SEL << 24) \ 583 | (MUX_ACLK_400_SUB_SEL << 20) \ 584 | (MUX_ACLK_266_ISP_SUB_SEL << 16) \ 585 | (MUX_ACLK_266_GPS_SUB_SEL << 12) \ 586 | (MUX_ACLK_300_GSCL_SUB_SEL << 10) \ 587 | (MUX_ACLK_266_GSCL_SUB_SEL << 8) \ 588 | (MUX_ACLK_300_DISP1_SUB_SEL << 6) \ 589 | (MUX_ACLK_200_DISP1_SUB_SEL << 4)) 590 591 #define CLK_SRC_TOP4_VAL NOT_AVAILABLE 592 #define CLK_SRC_TOP5_VAL NOT_AVAILABLE 593 #define CLK_SRC_TOP6_VAL NOT_AVAILABLE 594 #define CLK_SRC_TOP7_VAL NOT_AVAILABLE 595 596 /* CLK_DIV_TOP0 */ 597 #define ACLK_300_DISP1_RATIO 0x2 598 #define ACLK_400_G3D_RATIO 0x0 599 #define ACLK_333_RATIO 0x0 600 #define ACLK_266_RATIO 0x2 601 #define ACLK_200_RATIO 0x3 602 #define ACLK_166_RATIO 0x1 603 #define ACLK_133_RATIO 0x1 604 #define ACLK_66_RATIO 0x5 605 606 #define CLK_DIV_TOP0_VAL ((ACLK_300_DISP1_RATIO << 28) \ 607 | (ACLK_400_G3D_RATIO << 24) \ 608 | (ACLK_333_RATIO << 20) \ 609 | (ACLK_266_RATIO << 16) \ 610 | (ACLK_200_RATIO << 12) \ 611 | (ACLK_166_RATIO << 8) \ 612 | (ACLK_133_RATIO << 4) \ 613 | (ACLK_66_RATIO)) 614 615 /* CLK_DIV_TOP1 */ 616 #define ACLK_MIPI_HSI_TX_BASE_RATIO 0x3 617 #define ACLK_66_PRE_RATIO 0x1 618 #define ACLK_400_ISP_RATIO 0x1 619 #define ACLK_400_IOP_RATIO 0x1 620 #define ACLK_300_GSCL_RATIO 0x2 621 622 #define CLK_DIV_TOP1_VAL ((ACLK_MIPI_HSI_TX_BASE_RATIO << 28) \ 623 | (ACLK_66_PRE_RATIO << 24) \ 624 | (ACLK_400_ISP_RATIO << 20) \ 625 | (ACLK_400_IOP_RATIO << 16) \ 626 | (ACLK_300_GSCL_RATIO << 12)) 627 628 #define CLK_DIV_TOP2_VAL NOT_AVAILABLE 629 630 /* PLL Lock Value Factor */ 631 #define PLL_LOCK_FACTOR 250 632 #define PLL_X_LOCK_FACTOR 3000 633 634 /* CLK_SRC_PERIC0 */ 635 #define PWM_SEL 6 636 #define UART3_SEL 6 637 #define UART2_SEL 6 638 #define UART1_SEL 6 639 #define UART0_SEL 6 640 /* SRC_CLOCK = SCLK_MPLL */ 641 #define CLK_SRC_PERIC0_VAL ((PWM_SEL << 24) \ 642 | (UART3_SEL << 12) \ 643 | (UART2_SEL << 8) \ 644 | (UART1_SEL << 4) \ 645 | (UART0_SEL)) 646 647 /* CLK_SRC_PERIC1 */ 648 /* SRC_CLOCK = SCLK_MPLL */ 649 #define SPI0_SEL 6 650 #define SPI1_SEL 6 651 #define SPI2_SEL 6 652 #define CLK_SRC_PERIC1_VAL ((SPI2_SEL << 24) \ 653 | (SPI1_SEL << 20) \ 654 | (SPI0_SEL << 16)) 655 656 /* CLK_DIV_PERIL0 */ 657 #define UART5_RATIO 7 658 #define UART4_RATIO 7 659 #define UART3_RATIO 7 660 #define UART2_RATIO 7 661 #define UART1_RATIO 7 662 #define UART0_RATIO 7 663 664 #define CLK_DIV_PERIC0_VAL ((UART3_RATIO << 12) \ 665 | (UART2_RATIO << 8) \ 666 | (UART1_RATIO << 4) \ 667 | (UART0_RATIO)) 668 /* CLK_DIV_PERIC1 */ 669 #define SPI1_RATIO 0x7 670 #define SPI0_RATIO 0xf 671 #define SPI1_SUB_RATIO 0x0 672 #define SPI0_SUB_RATIO 0x0 673 #define CLK_DIV_PERIC1_VAL ((SPI1_SUB_RATIO << 24) \ 674 | ((SPI1_RATIO << 16) \ 675 | (SPI0_SUB_RATIO << 8) \ 676 | (SPI0_RATIO << 0))) 677 678 /* CLK_DIV_PERIC2 */ 679 #define SPI2_RATIO 0xf 680 #define SPI2_SUB_RATIO 0x0 681 #define CLK_DIV_PERIC2_VAL ((SPI2_SUB_RATIO << 8) \ 682 | (SPI2_RATIO << 0)) 683 684 /* CLK_DIV_PERIC3 */ 685 #define PWM_RATIO 8 686 #define CLK_DIV_PERIC3_VAL (PWM_RATIO << 0) 687 688 689 /* CLK_DIV_PERIC4 */ 690 #define CLK_DIV_PERIC4_VAL NOT_AVAILABLE 691 692 /* CLK_SRC_DISP1_0 */ 693 #define CLK_SRC_DISP1_0_VAL 0x6 694 #define CLK_DIV_DISP1_0_VAL NOT_AVAILABLE 695 696 #define APLL_FOUT (1 << 0) 697 #define KPLL_FOUT NOT_AVAILABLE 698 699 #define CLK_DIV_CPERI1_VAL NOT_AVAILABLE 700 701 #else 702 703 #define CPU_CONFIG_STATUS_OFFSET 0x80 704 #define CPU_RST_FLAG_VAL 0xFCBA0D10 705 #define PAD_RETENTION_DRAM_COREBLK_VAL 0x10000000 706 707 /* APLL_CON1 */ 708 #define APLL_CON1_VAL (0x0020F300) 709 710 /* MPLL_CON1 */ 711 #define MPLL_CON1_VAL (0x0020F300) 712 713 714 /* CPLL_CON1 */ 715 #define CPLL_CON1_VAL 0x0020f300 716 717 /* DPLL_CON1 */ 718 #define DPLL_CON1_VAL (0x0020F300) 719 720 /* GPLL_CON1 */ 721 #define GPLL_CON1_VAL (NOT_AVAILABLE) 722 723 724 /* EPLL_CON1, CON2 */ 725 #define EPLL_CON1_VAL 0x00000000 726 #define EPLL_CON2_VAL 0x00000080 727 728 /* VPLL_CON1, CON2 */ 729 #define VPLL_CON1_VAL 0x0020f300 730 #define VPLL_CON2_VAL NOT_AVAILABLE 731 732 /* RPLL_CON1, CON2 */ 733 #define RPLL_CON1_VAL 0x00000000 734 #define RPLL_CON2_VAL 0x00000080 735 736 /* BPLL_CON1 */ 737 #define BPLL_CON1_VAL 0x0020f300 738 739 /* SPLL_CON1 */ 740 #define SPLL_CON1_VAL 0x0020f300 741 742 /* IPLL_CON1 */ 743 #define IPLL_CON1_VAL 0x00000080 744 745 /* KPLL_CON1 */ 746 #define KPLL_CON1_VAL 0x200000 747 748 /* CLK_SRC_ISP */ 749 #define CLK_SRC_ISP_VAL 0x33366000 750 #define CLK_DIV_ISP0_VAL 0x13131300 751 #define CLK_DIV_ISP1_VAL 0xbb110202 752 753 754 /* CLK_FSYS */ 755 #define CLK_SRC_FSYS0_VAL 0x33033300 756 #define CLK_DIV_FSYS0_VAL 0x0 757 #define CLK_DIV_FSYS1_VAL 0x04f13c4f 758 #define CLK_DIV_FSYS2_VAL 0x041d0000 759 760 /* CLK_SRC_CPU */ 761 /* 0 = MOUTAPLL, 1 = SCLKMPLL */ 762 #define MUX_HPM_SEL 1 763 #define MUX_CPU_SEL 0 764 #define MUX_APLL_SEL 1 765 766 #define CLK_SRC_CPU_VAL ((MUX_HPM_SEL << 20) \ 767 | (MUX_CPU_SEL << 16) \ 768 | (MUX_APLL_SEL)) 769 770 /* CLK_SRC_CDREX */ 771 #define CLK_SRC_CDREX_VAL 0x00000011 772 773 /* CLK_DIV_CDREX */ 774 #define CLK_DIV_CDREX0_VAL 0x30010100 775 #define CLK_DIV_CDREX1_VAL 0x300 776 777 #define CLK_DIV_CDREX_VAL 0x17010100 778 779 /* CLK_DIV_CPU0_VAL */ 780 #define CLK_DIV_CPU0_VAL 0x01440020 781 782 /* CLK_SRC_TOP */ 783 #define CLK_SRC_TOP0_VAL 0x12221222 784 #define CLK_SRC_TOP1_VAL 0x00100200 785 #define CLK_SRC_TOP2_VAL 0x11101000 786 #define CLK_SRC_TOP3_VAL 0x11111111 787 #define CLK_SRC_TOP4_VAL 0x11110111 788 #define CLK_SRC_TOP5_VAL 0x11111101 789 #define CLK_SRC_TOP6_VAL 0x11110111 790 #define CLK_SRC_TOP7_VAL 0x00022200 791 792 /* CLK_DIV_TOP */ 793 #define CLK_DIV_TOP0_VAL 0x23712311 794 #define CLK_DIV_TOP1_VAL 0x13100B00 795 #define CLK_DIV_TOP2_VAL 0x11101100 796 797 /* PLL Lock Value Factor */ 798 #define PLL_LOCK_FACTOR 200 799 #define PLL_X_LOCK_FACTOR 3000 800 801 /* CLK_SRC_PERIC0 */ 802 #define SPDIF_SEL 1 803 #define PWM_SEL 3 804 #define UART4_SEL 3 805 #define UART3_SEL 3 806 #define UART2_SEL 3 807 #define UART1_SEL 3 808 #define UART0_SEL 3 809 /* SRC_CLOCK = SCLK_RPLL */ 810 #define CLK_SRC_PERIC0_VAL ((SPDIF_SEL << 28) \ 811 | (PWM_SEL << 24) \ 812 | (UART4_SEL << 20) \ 813 | (UART3_SEL << 16) \ 814 | (UART2_SEL << 12) \ 815 | (UART1_SEL << 8) \ 816 | (UART0_SEL << 4)) 817 818 /* CLK_SRC_PERIC1 */ 819 /* SRC_CLOCK = SCLK_EPLL */ 820 #define SPI0_SEL 6 821 #define SPI1_SEL 6 822 #define SPI2_SEL 6 823 #define AUDIO0_SEL 6 824 #define AUDIO1_SEL 6 825 #define AUDIO2_SEL 6 826 #define CLK_SRC_PERIC1_VAL ((SPI2_SEL << 28) \ 827 | (SPI1_SEL << 24) \ 828 | (SPI0_SEL << 20) \ 829 | (AUDIO2_SEL << 16) \ 830 | (AUDIO2_SEL << 12) \ 831 | (AUDIO2_SEL << 8)) 832 833 /* CLK_DIV_PERIC0 */ 834 #define PWM_RATIO 8 835 #define UART4_RATIO 9 836 #define UART3_RATIO 9 837 #define UART2_RATIO 9 838 #define UART1_RATIO 9 839 #define UART0_RATIO 9 840 841 #define CLK_DIV_PERIC0_VAL ((PWM_RATIO << 28) \ 842 | (UART4_RATIO << 24) \ 843 | (UART3_RATIO << 20) \ 844 | (UART2_RATIO << 16) \ 845 | (UART1_RATIO << 12) \ 846 | (UART0_RATIO << 8)) 847 /* CLK_DIV_PERIC1 */ 848 #define SPI2_RATIO 0x1 849 #define SPI1_RATIO 0x1 850 #define SPI0_RATIO 0x1 851 #define CLK_DIV_PERIC1_VAL ((SPI2_RATIO << 28) \ 852 | (SPI1_RATIO << 24) \ 853 | (SPI0_RATIO << 20)) 854 855 /* CLK_DIV_PERIC2 */ 856 #define PCM2_RATIO 0x3 857 #define PCM1_RATIO 0x3 858 #define CLK_DIV_PERIC2_VAL ((PCM2_RATIO << 24) \ 859 | (PCM1_RATIO << 16)) 860 861 /* CLK_DIV_PERIC3 */ 862 #define AUDIO2_RATIO 0x5 863 #define AUDIO1_RATIO 0x5 864 #define AUDIO0_RATIO 0x5 865 #define CLK_DIV_PERIC3_VAL ((AUDIO2_RATIO << 28) \ 866 | (AUDIO1_RATIO << 24) \ 867 | (AUDIO0_RATIO << 20)) 868 869 /* CLK_DIV_PERIC4 */ 870 #define SPI2_PRE_RATIO 0x2 871 #define SPI1_PRE_RATIO 0x2 872 #define SPI0_PRE_RATIO 0x2 873 #define CLK_DIV_PERIC4_VAL ((SPI2_PRE_RATIO << 24) \ 874 | (SPI1_PRE_RATIO << 16) \ 875 | (SPI0_PRE_RATIO << 8)) 876 877 /* CLK_SRC_DISP1_0 */ 878 #define CLK_SRC_DISP1_0_VAL 0x10666600 879 #define CLK_DIV_DISP1_0_VAL 0x01050211 880 881 #define APLL_FOUT (1 << 0) 882 #define KPLL_FOUT (1 << 0) 883 884 #define CLK_DIV_CPERI1_VAL 0x3f3f0000 885 #endif 886 887 struct mem_timings; 888 889 /* Errors that we can encourter in low-level setup */ 890 enum { 891 SETUP_ERR_OK, 892 SETUP_ERR_RDLV_COMPLETE_TIMEOUT = -1, 893 SETUP_ERR_ZQ_CALIBRATION_FAILURE = -2, 894 }; 895 896 /* 897 * Memory variant specific initialization code for DDR3 898 * 899 * @param mem Memory timings for this memory type. 900 * @param reset Reset DDR PHY during initialization. 901 * @return 0 if ok, SETUP_ERR_... if there is a problem 902 */ 903 int ddr3_mem_ctrl_init(struct mem_timings *mem, int reset); 904 905 /* Memory variant specific initialization code for LPDDR3 */ 906 void lpddr3_mem_ctrl_init(void); 907 908 /* 909 * Configure ZQ I/O interface 910 * 911 * @param mem Memory timings for this memory type. 912 * @param phy0_con16 Register address for dmc_phy0->phy_con16 913 * @param phy1_con16 Register address for dmc_phy1->phy_con16 914 * @param phy0_con17 Register address for dmc_phy0->phy_con17 915 * @param phy1_con17 Register address for dmc_phy1->phy_con17 916 * @return 0 if ok, -1 on error 917 */ 918 int dmc_config_zq(struct mem_timings *mem, uint32_t *phy0_con16, 919 uint32_t *phy1_con16, uint32_t *phy0_con17, 920 uint32_t *phy1_con17); 921 /* 922 * Send NOP and MRS/EMRS Direct commands 923 * 924 * @param mem Memory timings for this memory type. 925 * @param directcmd Register address for dmc_phy->directcmd 926 */ 927 void dmc_config_mrs(struct mem_timings *mem, uint32_t *directcmd); 928 929 /* 930 * Send PALL Direct commands 931 * 932 * @param mem Memory timings for this memory type. 933 * @param directcmd Register address for dmc_phy->directcmd 934 */ 935 void dmc_config_prech(struct mem_timings *mem, uint32_t *directcmd); 936 937 /* 938 * Reset the DLL. This function is common between DDR3 and LPDDR2. 939 * However, the reset value is different. So we are passing a flag 940 * ddr_mode to distinguish between LPDDR2 and DDR3. 941 * 942 * @param phycontrol0 Register address for dmc_phy->phycontrol0 943 * @param ddr_mode Type of DDR memory 944 */ 945 void update_reset_dll(uint32_t *phycontrol0, enum ddr_mode); 946 #endif 947