1// SPDX-License-Identifier: GPL-2.0+
2/*
3 * dts file for Xilinx ZynqMP ZCU111
4 *
5 * (C) Copyright 2017 - 2018, Xilinx, Inc.
6 *
7 * Michal Simek <michal.simek@xilinx.com>
8 */
9
10/dts-v1/;
11
12#include "zynqmp.dtsi"
13#include "zynqmp-clk-ccf.dtsi"
14#include <dt-bindings/input/input.h>
15#include <dt-bindings/gpio/gpio.h>
16#include <dt-bindings/phy/phy.h>
17
18/ {
19	model = "ZynqMP ZCU111 RevA";
20	compatible = "xlnx,zynqmp-zcu111-revA", "xlnx,zynqmp-zcu111", "xlnx,zynqmp";
21
22	aliases {
23		ethernet0 = &gem3;
24		gpio0 = &gpio;
25		i2c0 = &i2c0;
26		i2c1 = &i2c1;
27		mmc0 = &sdhci1;
28		rtc0 = &rtc;
29		serial0 = &uart0;
30		serial1 = &dcc;
31		spi0 = &qspi;
32		usb0 = &usb0;
33	};
34
35	chosen {
36		bootargs = "earlycon";
37		stdout-path = "serial0:115200n8";
38	};
39
40	memory@0 {
41		device_type = "memory";
42		reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
43		/* Another 4GB connected to PL */
44	};
45
46	gpio-keys {
47		compatible = "gpio-keys";
48		#address-cells = <1>;
49		#size-cells = <0>;
50		autorepeat;
51		sw19 {
52			label = "sw19";
53			gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
54			linux,code = <KEY_DOWN>;
55			gpio-key,wakeup;
56			autorepeat;
57		};
58	};
59
60	leds {
61		compatible = "gpio-leds";
62		heartbeat_led {
63			label = "heartbeat";
64			gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
65			linux,default-trigger = "heartbeat";
66		};
67	};
68};
69
70&dcc {
71	status = "okay";
72};
73
74&fpd_dma_chan1 {
75	status = "okay";
76};
77
78&fpd_dma_chan2 {
79	status = "okay";
80};
81
82&fpd_dma_chan3 {
83	status = "okay";
84};
85
86&fpd_dma_chan4 {
87	status = "okay";
88};
89
90&fpd_dma_chan5 {
91	status = "okay";
92};
93
94&fpd_dma_chan6 {
95	status = "okay";
96};
97
98&fpd_dma_chan7 {
99	status = "okay";
100};
101
102&fpd_dma_chan8 {
103	status = "okay";
104};
105
106&gem3 {
107	status = "okay";
108	phy-handle = <&phy0>;
109	phy-mode = "rgmii-id";
110	phy0: phy@c {
111		reg = <0xc>;
112		ti,rx-internal-delay = <0x8>;
113		ti,tx-internal-delay = <0xa>;
114		ti,fifo-depth = <0x1>;
115	};
116};
117
118&gpio {
119	status = "okay";
120};
121
122&gpu {
123	status = "okay";
124};
125
126&i2c0 {
127	status = "okay";
128	clock-frequency = <400000>;
129
130	tca6416_u22: gpio@20 {
131		compatible = "ti,tca6416";
132		reg = <0x20>;
133		gpio-controller; /* interrupt not connected */
134		#gpio-cells = <2>;
135		/*
136		 * IRQ not connected
137		 * Lines:
138		 * 0 - MAX6643_OT_B
139		 * 1 - MAX6643_FANFAIL_B
140		 * 2 - MIO26_PMU_INPUT_LS
141		 * 4 - SFP_SI5382_INT_ALM
142		 * 5 - IIC_MUX_RESET_B
143		 * 6 - GEM3_EXP_RESET_B
144		 * 10 - FMCP_HSPC_PRSNT_M2C_B
145		 * 11 - CLK_SPI_MUX_SEL0
146		 * 12 - CLK_SPI_MUX_SEL1
147		 * 16 - IRPS5401_ALERT_B
148		 * 17 - INA226_PMBUS_ALERT
149		 * 3, 7, 13-15 - not connected
150		 */
151	};
152
153	i2c-mux@75 { /* u23 */
154		compatible = "nxp,pca9544";
155		#address-cells = <1>;
156		#size-cells = <0>;
157		reg = <0x75>;
158		i2c@0 {
159			#address-cells = <1>;
160			#size-cells = <0>;
161			reg = <0>;
162			/* PS_PMBUS */
163			/* PMBUS_ALERT done via pca9544 */
164			ina226@40 { /* u67 */
165				compatible = "ti,ina226";
166				reg = <0x40>;
167				shunt-resistor = <2000>;
168			};
169			ina226@41 { /* u59 */
170				compatible = "ti,ina226";
171				reg = <0x41>;
172				shunt-resistor = <5000>;
173			};
174			ina226@42 { /* u61 */
175				compatible = "ti,ina226";
176				reg = <0x42>;
177				shunt-resistor = <5000>;
178			};
179			ina226@43 { /* u60 */
180				compatible = "ti,ina226";
181				reg = <0x43>;
182				shunt-resistor = <5000>;
183			};
184			ina226@45 { /* u64 */
185				compatible = "ti,ina226";
186				reg = <0x45>;
187				shunt-resistor = <5000>;
188			};
189			ina226@46 { /* u69 */
190				compatible = "ti,ina226";
191				reg = <0x46>;
192				shunt-resistor = <2000>;
193			};
194			ina226@47 { /* u66 */
195				compatible = "ti,ina226";
196				reg = <0x47>;
197				shunt-resistor = <5000>;
198			};
199			ina226@48 { /* u65 */
200				compatible = "ti,ina226";
201				reg = <0x48>;
202				shunt-resistor = <5000>;
203			};
204			ina226@49 { /* u63 */
205				compatible = "ti,ina226";
206				reg = <0x49>;
207				shunt-resistor = <5000>;
208			};
209			ina226@4a { /* u3 */
210				compatible = "ti,ina226";
211				reg = <0x4a>;
212				shunt-resistor = <5000>;
213			};
214			ina226@4b { /* u71 */
215				compatible = "ti,ina226";
216				reg = <0x4b>;
217				shunt-resistor = <5000>;
218			};
219			ina226@4c { /* u77 */
220				compatible = "ti,ina226";
221				reg = <0x4c>;
222				shunt-resistor = <5000>;
223			};
224			ina226@4d { /* u73 */
225				compatible = "ti,ina226";
226				reg = <0x4d>;
227				shunt-resistor = <5000>;
228			};
229			ina226@4e { /* u79 */
230				compatible = "ti,ina226";
231				reg = <0x4e>;
232				shunt-resistor = <5000>;
233			};
234		};
235		i2c@1 {
236			#address-cells = <1>;
237			#size-cells = <0>;
238			reg = <1>;
239			/* NC */
240		};
241		i2c@2 {
242			#address-cells = <1>;
243			#size-cells = <0>;
244			reg = <2>;
245			irps5401_43: irps54012@43 { /* IRPS5401 - u53 check these */
246				#clock-cells = <0>;
247				compatible = "infineon,irps5401";
248				reg = <0x43>;
249			};
250			irps5401_44: irps54012@44 { /* IRPS5401 - u55 */
251				#clock-cells = <0>;
252				compatible = "infineon,irps5401";
253				reg = <0x44>;
254			};
255			irps5401_45: irps54012@45 { /* IRPS5401 - u57 */
256				#clock-cells = <0>;
257				compatible = "infineon,irps5401";
258				reg = <0x45>;
259			};
260			/* u68 IR38064 +0 */
261			/* u70 IR38060 +1 */
262			/* u74 IR38060 +2 */
263			/* u75 IR38060 +6 */
264			/* J19 header too */
265
266		};
267		i2c@3 {
268			#address-cells = <1>;
269			#size-cells = <0>;
270			reg = <3>;
271			/* SYSMON */
272		};
273	};
274};
275
276&i2c1 {
277	status = "okay";
278	clock-frequency = <400000>;
279
280	i2c-mux@74 { /* u26 */
281		compatible = "nxp,pca9548";
282		#address-cells = <1>;
283		#size-cells = <0>;
284		reg = <0x74>;
285		i2c@0 {
286			#address-cells = <1>;
287			#size-cells = <0>;
288			reg = <0>;
289			/*
290			 * IIC_EEPROM 1kB memory which uses 256B blocks
291			 * where every block has different address.
292			 *    0 - 256B address 0x54
293			 * 256B - 512B address 0x55
294			 * 512B - 768B address 0x56
295			 * 768B - 1024B address 0x57
296			 */
297			eeprom: eeprom@54 { /* u88 */
298				compatible = "atmel,24c08";
299				reg = <0x54>;
300			};
301		};
302		i2c@1 {
303			#address-cells = <1>;
304			#size-cells = <0>;
305			reg = <1>;
306			si5341: clock-generator@36 { /* SI5341 - u46 */
307				compatible = "si5341";
308				reg = <0x36>;
309			};
310
311		};
312		i2c@2 {
313			#address-cells = <1>;
314			#size-cells = <0>;
315			reg = <2>;
316			si570_1: clock-generator@5d { /* USER SI570 - u47 */
317				#clock-cells = <0>;
318				compatible = "silabs,si570";
319				reg = <0x5d>;
320				temperature-stability = <50>;
321				factory-fout = <300000000>;
322				clock-frequency = <300000000>;
323			};
324		};
325		i2c@3 {
326			#address-cells = <1>;
327			#size-cells = <0>;
328			reg = <3>;
329			si570_2: clock-generator@5d { /* USER MGT SI570 - u49 */
330				#clock-cells = <0>;
331				compatible = "silabs,si570";
332				reg = <0x5d>;
333				temperature-stability = <50>;
334				factory-fout = <156250000>;
335				clock-frequency = <148500000>;
336			};
337		};
338		i2c@4 {
339			#address-cells = <1>;
340			#size-cells = <0>;
341			reg = <4>;
342			si5328: clock-generator@69 { /* SI5328 - u48 */
343				compatible = "silabs,si5328";
344				reg = <0x69>;
345			};
346		};
347		i2c@5 {
348			#address-cells = <1>;
349			#size-cells = <0>;
350			reg = <5>;
351				sc18is603@2f { /* sc18is602 - u93 */
352					compatible = "nxp,sc18is603";
353					reg = <0x2f>;
354					/* 4 gpios for CS not handled by driver */
355					/*
356					 * USB2ANY cable or
357					 * LMK04208 - u90 or
358					 * LMX2594 - u102 or
359					 * LMX2594 - u103 or
360					 * LMX2594 - u104
361					 */
362				};
363		};
364		i2c@6 {
365			#address-cells = <1>;
366			#size-cells = <0>;
367			reg = <6>;
368			/* FMC connector */
369		};
370		/* 7 NC */
371	};
372
373	i2c-mux@75 {
374		compatible = "nxp,pca9548"; /* u27 */
375		#address-cells = <1>;
376		#size-cells = <0>;
377		reg = <0x75>;
378
379		i2c@0 {
380			#address-cells = <1>;
381			#size-cells = <0>;
382			reg = <0>;
383			/* FMCP_HSPC_IIC */
384		};
385		i2c@1 {
386			#address-cells = <1>;
387			#size-cells = <0>;
388			reg = <1>;
389			/* NC */
390		};
391		i2c@2 {
392			#address-cells = <1>;
393			#size-cells = <0>;
394			reg = <2>;
395			/* SYSMON */
396		};
397		i2c@3 {
398			#address-cells = <1>;
399			#size-cells = <0>;
400			reg = <3>;
401			/* DDR4 SODIMM */
402			dev@19 { /* u-boot detection FIXME */
403				compatible = "xxx";
404				reg = <0x19>;
405			};
406			dev@30 { /* u-boot detection */
407				compatible = "xxx";
408				reg = <0x30>;
409			};
410			dev@35 { /* u-boot detection */
411				compatible = "xxx";
412				reg = <0x35>;
413			};
414			dev@36 { /* u-boot detection */
415				compatible = "xxx";
416				reg = <0x36>;
417			};
418			dev@51 { /* u-boot detection - maybe SPD */
419				compatible = "xxx";
420				reg = <0x51>;
421			};
422		};
423		i2c@4 {
424			#address-cells = <1>;
425			#size-cells = <0>;
426			reg = <4>;
427			/* SFP3 */
428		};
429		i2c@5 {
430			#address-cells = <1>;
431			#size-cells = <0>;
432			reg = <5>;
433			/* SFP2 */
434		};
435		i2c@6 {
436			#address-cells = <1>;
437			#size-cells = <0>;
438			reg = <6>;
439			/* SFP1 */
440		};
441		i2c@7 {
442			#address-cells = <1>;
443			#size-cells = <0>;
444			reg = <7>;
445			/* SFP0 */
446		};
447	};
448};
449
450&qspi {
451	status = "okay";
452	is-dual = <1>;
453	flash@0 {
454		compatible = "m25p80"; /* 32MB */
455		#address-cells = <1>;
456		#size-cells = <1>;
457		reg = <0x0>;
458		spi-tx-bus-width = <1>;
459		spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
460		spi-max-frequency = <108000000>; /* Based on DC1 spec */
461		partition@qspi-fsbl-uboot { /* for testing purpose */
462			label = "qspi-fsbl-uboot";
463			reg = <0x0 0x100000>;
464		};
465		partition@qspi-linux { /* for testing purpose */
466			label = "qspi-linux";
467			reg = <0x100000 0x500000>;
468		};
469		partition@qspi-device-tree { /* for testing purpose */
470			label = "qspi-device-tree";
471			reg = <0x600000 0x20000>;
472		};
473		partition@qspi-rootfs { /* for testing purpose */
474			label = "qspi-rootfs";
475			reg = <0x620000 0x5E0000>;
476		};
477	};
478};
479
480&rtc {
481	status = "okay";
482};
483
484&sata {
485	status = "okay";
486	/* SATA OOB timing settings */
487	ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
488	ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
489	ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
490	ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
491	ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
492	ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
493	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
494	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
495	phy-names = "sata-phy";
496	phys = <&lane3 PHY_TYPE_SATA 1 3 125000000>;
497};
498
499/* SD1 with level shifter */
500&sdhci1 {
501	status = "okay";
502	no-1-8-v;
503	disable-wp;
504	xlnx,mio_bank = <1>;
505};
506
507&serdes {
508	status = "okay";
509};
510
511&uart0 {
512	status = "okay";
513};
514
515/* ULPI SMSC USB3320 */
516&usb0 {
517	status = "okay";
518};
519
520&dwc3_0 {
521	status = "okay";
522	dr_mode = "host";
523	snps,usb3_lpm_capable;
524	phy-names = "usb3-phy";
525	phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
526};
527