1/*
2 * dts file for Xilinx ZynqMP zc1751-xm015-dc1
3 *
4 * (C) Copyright 2015, Xilinx, Inc.
5 *
6 * Michal Simek <michal.simek@xilinx.com>
7 *
8 * SPDX-License-Identifier:	GPL-2.0+
9 */
10
11/dts-v1/;
12
13#include "zynqmp.dtsi"
14#include "zynqmp-clk-ccf.dtsi"
15
16/ {
17	model = "ZynqMP zc1751-xm015-dc1 RevA";
18	compatible = "xlnx,zynqmp-zc1751", "xlnx,zynqmp";
19
20	aliases {
21		ethernet0 = &gem3;
22		gpio0 = &gpio;
23		i2c0 = &i2c1;
24		mmc0 = &sdhci0;
25		mmc1 = &sdhci1;
26		rtc0 = &rtc;
27		serial0 = &uart0;
28		spi0 = &qspi;
29		usb0 = &usb0;
30	};
31
32	chosen {
33		bootargs = "earlycon";
34		stdout-path = "serial0:115200n8";
35	};
36
37	memory@0 {
38		device_type = "memory";
39		reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
40	};
41};
42
43/* fpd_dma clk 667MHz, lpd_dma 500MHz */
44&fpd_dma_chan1 {
45	status = "okay";
46};
47
48&fpd_dma_chan2 {
49	status = "okay";
50};
51
52&fpd_dma_chan3 {
53	status = "okay";
54};
55
56&fpd_dma_chan4 {
57	status = "okay";
58};
59
60&fpd_dma_chan5 {
61	status = "okay";
62};
63
64&fpd_dma_chan6 {
65	status = "okay";
66};
67
68&fpd_dma_chan7 {
69	status = "okay";
70};
71
72&fpd_dma_chan8 {
73	status = "okay";
74};
75
76&gem3 {
77	status = "okay";
78	phy-handle = <&phy0>;
79	phy-mode = "rgmii-id";
80	phy0: phy@0 {
81		reg = <0>;
82	};
83};
84
85&gpio {
86	status = "okay";
87};
88
89&gpu {
90	status = "okay";
91};
92
93&i2c1 {
94	status = "okay";
95	clock-frequency = <400000>;
96	eeprom@55 {
97		compatible = "at,24c64"; /* 24AA64 */
98		reg = <0x55>;
99	};
100};
101
102&qspi {
103	status = "okay";
104	flash@0 {
105		compatible = "m25p80"; /* Micron MT25QU512ABB8ESF */
106		#address-cells = <1>;
107		#size-cells = <1>;
108		reg = <0x0>;
109		spi-tx-bus-width = <1>;
110		spi-rx-bus-width = <4>;
111		spi-max-frequency = <108000000>; /* Based on DC1 spec */
112		partition@qspi-fsbl-uboot { /* for testing purpose */
113			label = "qspi-fsbl-uboot";
114			reg = <0x0 0x100000>;
115		};
116		partition@qspi-linux { /* for testing purpose */
117			label = "qspi-linux";
118			reg = <0x100000 0x500000>;
119		};
120		partition@qspi-device-tree { /* for testing purpose */
121			label = "qspi-device-tree";
122			reg = <0x600000 0x20000>;
123		};
124		partition@qspi-rootfs { /* for testing purpose */
125			label = "qspi-rootfs";
126			reg = <0x620000 0x5E0000>;
127		};
128	};
129};
130
131&rtc {
132	status = "okay";
133};
134
135&sata {
136	status = "okay";
137	/* SATA phy OOB timing settings */
138	ceva,p0-cominit-params = /bits/ 8 <0x1B 0x4D 0x18 0x28>;
139	ceva,p0-comwake-params = /bits/ 8 <0x06 0x19 0x08 0x0E>;
140	ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
141	ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
142	ceva,p1-cominit-params = /bits/ 8 <0x1B 0x4D 0x18 0x28>;
143	ceva,p1-comwake-params = /bits/ 8 <0x06 0x19 0x08 0x0E>;
144	ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
145	ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
146};
147
148/* eMMC */
149&sdhci0 {
150	status = "okay";
151	bus-width = <8>;
152	xlnx,mio_bank = <0>;
153};
154
155/* SD1 with level shifter */
156&sdhci1 {
157	status = "okay";
158	no-1-8-v;       /* for 1.0 silicon */
159	xlnx,mio_bank = <1>;
160};
161
162&uart0 {
163	status = "okay";
164};
165
166/* ULPI SMSC USB3320 */
167&usb0 {
168	status = "okay";
169};
170
171&dwc3_0 {
172	status = "okay";
173	dr_mode = "host";
174};
175
176&xilinx_drm {
177	status = "okay";
178};
179
180&xlnx_dp {
181	status = "okay";
182};
183
184&xlnx_dp_sub {
185	status = "okay";
186	xlnx,vid-clk-pl;
187};
188
189&xlnx_dp_snd_pcm0 {
190	status = "okay";
191};
192
193&xlnx_dp_snd_pcm1 {
194	status = "okay";
195};
196
197&xlnx_dp_snd_card {
198	status = "okay";
199};
200
201&xlnx_dp_snd_codec0 {
202	status = "okay";
203};
204
205&xlnx_dpdma {
206	status = "okay";
207};
208