1#include <dt-bindings/input/input.h> 2#include "tegra124.dtsi" 3 4/ { 5 aliases { 6 rtc0 = "/i2c@7000d000/pmic@40"; 7 rtc1 = "/rtc@7000e000"; 8 serial0 = &uarta; 9 }; 10 11 memory { 12 reg = <0x80000000 0x80000000>; 13 }; 14 15 host1x@50000000 { 16 hdmi@54280000 { 17 status = "okay"; 18 19 vdd-supply = <&vdd_3v3_hdmi>; 20 pll-supply = <&vdd_hdmi_pll>; 21 hdmi-supply = <&vdd_5v0_hdmi>; 22 23 nvidia,ddc-i2c-bus = <&hdmi_ddc>; 24 nvidia,hpd-gpio = 25 <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>; 26 }; 27 28 sor@54540000 { 29 status = "okay"; 30 31 nvidia,dpaux = <&dpaux>; 32 nvidia,panel = <&panel>; 33 }; 34 35 dpaux@545c0000 { 36 vdd-supply = <&vdd_3v3_panel>; 37 status = "okay"; 38 }; 39 }; 40 41 serial@70006000 { 42 /* Debug connector on the bottom of the board near SD card. */ 43 status = "okay"; 44 }; 45 46 pwm@7000a000 { 47 status = "okay"; 48 }; 49 50 i2c@7000c000 { 51 status = "okay"; 52 clock-frequency = <100000>; 53 54 acodec: audio-codec@10 { 55 compatible = "maxim,max98090"; 56 reg = <0x10>; 57 interrupt-parent = <&gpio>; 58 interrupts = <TEGRA_GPIO(H, 4) GPIO_ACTIVE_HIGH>; 59 }; 60 61 temperature-sensor@4c { 62 compatible = "ti,tmp451"; 63 reg = <0x4c>; 64 interrupt-parent = <&gpio>; 65 interrupts = <TEGRA_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>; 66 67 #thermal-sensor-cells = <1>; 68 }; 69 }; 70 71 i2c@7000c400 { 72 status = "okay"; 73 clock-frequency = <100000>; 74 75 trackpad@15 { 76 compatible = "elan,ekth3000"; 77 reg = <0x15>; 78 interrupt-parent = <&gpio>; 79 interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_EDGE_FALLING>; 80 wakeup-source; 81 }; 82 }; 83 84 i2c@7000c500 { 85 status = "okay"; 86 clock-frequency = <400000>; 87 88 tpm@20 { 89 compatible = "infineon,slb9645tt"; 90 reg = <0x20>; 91 }; 92 }; 93 94 hdmi_ddc: i2c@7000c700 { 95 status = "okay"; 96 clock-frequency = <100000>; 97 }; 98 99 i2c@7000d000 { 100 status = "okay"; 101 clock-frequency = <400000>; 102 103 pmic: pmic@40 { 104 compatible = "ams,as3722"; 105 reg = <0x40>; 106 interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>; 107 108 ams,system-power-controller; 109 110 #interrupt-cells = <2>; 111 interrupt-controller; 112 113 gpio-controller; 114 #gpio-cells = <2>; 115 116 pinctrl-names = "default"; 117 pinctrl-0 = <&as3722_default>; 118 119 as3722_default: pinmux { 120 gpio0 { 121 pins = "gpio0"; 122 function = "gpio"; 123 bias-pull-down; 124 }; 125 126 gpio1 { 127 pins = "gpio1"; 128 function = "gpio"; 129 bias-pull-up; 130 }; 131 132 gpio2_4_7 { 133 pins = "gpio2", "gpio4", "gpio7"; 134 function = "gpio"; 135 bias-pull-up; 136 }; 137 138 gpio3_6 { 139 pins = "gpio3", "gpio6"; 140 bias-high-impedance; 141 }; 142 143 gpio5 { 144 pins = "gpio5"; 145 function = "clk32k-out"; 146 bias-pull-down; 147 }; 148 }; 149 150 regulators { 151 vsup-sd2-supply = <&vdd_5v0_sys>; 152 vsup-sd3-supply = <&vdd_5v0_sys>; 153 vsup-sd4-supply = <&vdd_5v0_sys>; 154 vsup-sd5-supply = <&vdd_5v0_sys>; 155 vin-ldo0-supply = <&vdd_1v35_lp0>; 156 vin-ldo1-6-supply = <&vdd_3v3_run>; 157 vin-ldo2-5-7-supply = <&vddio_1v8>; 158 vin-ldo3-4-supply = <&vdd_3v3_sys>; 159 vin-ldo9-10-supply = <&vdd_5v0_sys>; 160 vin-ldo11-supply = <&vdd_3v3_run>; 161 162 vdd_cpu: sd0 { 163 regulator-name = "+VDD_CPU_AP"; 164 regulator-min-microvolt = <700000>; 165 regulator-max-microvolt = <1350000>; 166 regulator-min-microamp = <3500000>; 167 regulator-max-microamp = <3500000>; 168 regulator-always-on; 169 regulator-boot-on; 170 ams,ext-control = <2>; 171 }; 172 173 sd1 { 174 regulator-name = "+VDD_CORE"; 175 regulator-min-microvolt = <700000>; 176 regulator-max-microvolt = <1350000>; 177 regulator-min-microamp = <2500000>; 178 regulator-max-microamp = <4000000>; 179 regulator-always-on; 180 regulator-boot-on; 181 ams,ext-control = <1>; 182 }; 183 184 vdd_1v35_lp0: sd2 { 185 regulator-name = "+1.35V_LP0(sd2)"; 186 regulator-min-microvolt = <1350000>; 187 regulator-max-microvolt = <1350000>; 188 regulator-always-on; 189 regulator-boot-on; 190 }; 191 192 sd3 { 193 regulator-name = "+1.35V_LP0(sd3)"; 194 regulator-min-microvolt = <1350000>; 195 regulator-max-microvolt = <1350000>; 196 regulator-always-on; 197 regulator-boot-on; 198 }; 199 200 vdd_1v05_run: sd4 { 201 regulator-name = "+1.05V_RUN"; 202 regulator-min-microvolt = <1050000>; 203 regulator-max-microvolt = <1050000>; 204 }; 205 206 vddio_1v8: sd5 { 207 regulator-name = "+1.8V_VDDIO"; 208 regulator-min-microvolt = <1800000>; 209 regulator-max-microvolt = <1800000>; 210 regulator-always-on; 211 }; 212 213 sd6 { 214 regulator-name = "+VDD_GPU_AP"; 215 regulator-min-microvolt = <650000>; 216 regulator-max-microvolt = <1200000>; 217 regulator-min-microamp = <3500000>; 218 regulator-max-microamp = <3500000>; 219 regulator-boot-on; 220 regulator-always-on; 221 }; 222 223 ldo0 { 224 regulator-name = "+1.05V_RUN_AVDD"; 225 regulator-min-microvolt = <1050000>; 226 regulator-max-microvolt = <1050000>; 227 regulator-boot-on; 228 regulator-always-on; 229 ams,ext-control = <1>; 230 }; 231 232 ldo1 { 233 regulator-name = "+1.8V_RUN_CAM"; 234 regulator-min-microvolt = <1800000>; 235 regulator-max-microvolt = <1800000>; 236 }; 237 238 ldo2 { 239 regulator-name = "+1.2V_GEN_AVDD"; 240 regulator-min-microvolt = <1200000>; 241 regulator-max-microvolt = <1200000>; 242 regulator-boot-on; 243 regulator-always-on; 244 }; 245 246 ldo3 { 247 regulator-name = "+1.00V_LP0_VDD_RTC"; 248 regulator-min-microvolt = <1000000>; 249 regulator-max-microvolt = <1000000>; 250 regulator-boot-on; 251 regulator-always-on; 252 ams,enable-tracking; 253 }; 254 255 vdd_run_cam: ldo4 { 256 regulator-name = "+3.3V_RUN_CAM"; 257 regulator-min-microvolt = <2800000>; 258 regulator-max-microvolt = <2800000>; 259 }; 260 261 ldo5 { 262 regulator-name = "+1.2V_RUN_CAM_FRONT"; 263 regulator-min-microvolt = <1200000>; 264 regulator-max-microvolt = <1200000>; 265 }; 266 267 vddio_sdmmc3: ldo6 { 268 regulator-name = "+VDDIO_SDMMC3"; 269 regulator-min-microvolt = <1800000>; 270 regulator-max-microvolt = <3300000>; 271 }; 272 273 ldo7 { 274 regulator-name = "+1.05V_RUN_CAM_REAR"; 275 regulator-min-microvolt = <1050000>; 276 regulator-max-microvolt = <1050000>; 277 }; 278 279 ldo9 { 280 regulator-name = "+2.8V_RUN_TOUCH"; 281 regulator-min-microvolt = <2800000>; 282 regulator-max-microvolt = <2800000>; 283 }; 284 285 ldo10 { 286 regulator-name = "+2.8V_RUN_CAM_AF"; 287 regulator-min-microvolt = <2800000>; 288 regulator-max-microvolt = <2800000>; 289 }; 290 291 ldo11 { 292 regulator-name = "+1.8V_RUN_VPP_FUSE"; 293 regulator-min-microvolt = <1800000>; 294 regulator-max-microvolt = <1800000>; 295 }; 296 }; 297 }; 298 }; 299 300 spi@7000d400 { 301 status = "okay"; 302 303 cros_ec: cros-ec@0 { 304 compatible = "google,cros-ec-spi"; 305 spi-max-frequency = <3000000>; 306 interrupt-parent = <&gpio>; 307 interrupts = <TEGRA_GPIO(C, 7) IRQ_TYPE_LEVEL_LOW>; 308 reg = <0>; 309 310 google,cros-ec-spi-msg-delay = <2000>; 311 312 i2c-tunnel { 313 compatible = "google,cros-ec-i2c-tunnel"; 314 #address-cells = <1>; 315 #size-cells = <0>; 316 317 google,remote-bus = <0>; 318 319 charger: bq24735@9 { 320 compatible = "ti,bq24735"; 321 reg = <0x9>; 322 interrupt-parent = <&gpio>; 323 interrupts = <TEGRA_GPIO(J, 0) 324 GPIO_ACTIVE_HIGH>; 325 ti,ac-detect-gpios = <&gpio 326 TEGRA_GPIO(J, 0) 327 GPIO_ACTIVE_HIGH>; 328 }; 329 330 battery: sbs-battery@b { 331 compatible = "sbs,sbs-battery"; 332 reg = <0xb>; 333 sbs,i2c-retry-count = <2>; 334 sbs,poll-retry-count = <10>; 335 power-supplies = <&charger>; 336 }; 337 }; 338 }; 339 }; 340 341 spi@7000da00 { 342 status = "okay"; 343 spi-max-frequency = <25000000>; 344 345 flash@0 { 346 compatible = "winbond,w25q32dw"; 347 spi-max-frequency = <25000000>; 348 reg = <0>; 349 }; 350 }; 351 352 pmc@7000e400 { 353 nvidia,invert-interrupt; 354 nvidia,suspend-mode = <0>; 355 nvidia,cpu-pwr-good-time = <500>; 356 nvidia,cpu-pwr-off-time = <300>; 357 nvidia,core-pwr-good-time = <641 3845>; 358 nvidia,core-pwr-off-time = <61036>; 359 nvidia,core-power-req-active-high; 360 nvidia,sys-clock-req-active-high; 361 }; 362 363 hda@70030000 { 364 status = "okay"; 365 }; 366 367 sdhci0_pwrseq: sdhci0_pwrseq { 368 compatible = "mmc-pwrseq-simple"; 369 370 reset-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>; 371 }; 372 373 sdhci@700b0000 { /* WiFi/BT on this bus */ 374 status = "okay"; 375 power-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_HIGH>; 376 bus-width = <4>; 377 no-1-8-v; 378 non-removable; 379 mmc-pwrseq = <&sdhci0_pwrseq>; 380 vmmc-supply = <&vdd_3v3_lp0>; 381 vqmmc-supply = <&vddio_1v8>; 382 keep-power-in-suspend; 383 }; 384 385 sdhci@700b0400 { /* SD Card on this bus */ 386 status = "okay"; 387 cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>; 388 power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>; 389 wp-gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>; 390 bus-width = <4>; 391 no-1-8-v; 392 vqmmc-supply = <&vddio_sdmmc3>; 393 }; 394 395 sdhci@700b0600 { /* eMMC on this bus */ 396 status = "okay"; 397 bus-width = <8>; 398 no-1-8-v; 399 non-removable; 400 }; 401 402 /* CPU DFLL clock */ 403 clock@70110000 { 404 status = "disabled"; 405 vdd-cpu-supply = <&vdd_cpu>; 406 nvidia,i2c-fs-rate = <400000>; 407 }; 408 409 ahub@70300000 { 410 i2s@70301100 { 411 status = "okay"; 412 }; 413 }; 414 415 usb@7d000000 { /* Rear external USB port. */ 416 status = "okay"; 417 dr_mode = "otg"; 418 nvidia,vbus-gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>; 419 }; 420 421 usb-phy@7d000000 { 422 status = "okay"; 423 vbus-supply = <&vdd_usb1_vbus>; 424 }; 425 426 usb@7d004000 { /* Internal webcam. */ 427 status = "okay"; 428 phy_type = "hsic"; 429 }; 430 431 usb-phy@7d004000 { 432 status = "okay"; 433 phy_type = "hsic"; 434 vbus-supply = <&vdd_run_cam>; 435 }; 436 437 usb@7d008000 { /* Left external USB port. */ 438 status = "okay"; 439 nvidia,vbus-gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>; 440 }; 441 442 usb-phy@7d008000 { 443 status = "okay"; 444 vbus-supply = <&vdd_usb3_vbus>; 445 }; 446 447 backlight: backlight { 448 compatible = "pwm-backlight"; 449 450 enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>; 451 power-supply = <&vdd_led>; 452 pwms = <&pwm 1 1000000>; 453 454 default-brightness-level = <224>; 455 brightness-levels = 456 < 0 1 2 3 4 5 6 7 457 8 9 10 11 12 13 14 15 458 16 17 18 19 20 21 22 23 459 24 25 26 27 28 29 30 31 460 32 33 34 35 36 37 38 39 461 40 41 42 43 44 45 46 47 462 48 49 50 51 52 53 54 55 463 56 57 58 59 60 61 62 63 464 64 65 66 67 68 69 70 71 465 72 73 74 75 76 77 78 79 466 80 81 82 83 84 85 86 87 467 88 89 90 91 92 93 94 95 468 96 97 98 99 100 101 102 103 469 104 105 106 107 108 109 110 111 470 112 113 114 115 116 117 118 119 471 120 121 122 123 124 125 126 127 472 128 129 130 131 132 133 134 135 473 136 137 138 139 140 141 142 143 474 144 145 146 147 148 149 150 151 475 152 153 154 155 156 157 158 159 476 160 161 162 163 164 165 166 167 477 168 169 170 171 172 173 174 175 478 176 177 178 179 180 181 182 183 479 184 185 186 187 188 189 190 191 480 192 193 194 195 196 197 198 199 481 200 201 202 203 204 205 206 207 482 208 209 210 211 212 213 214 215 483 216 217 218 219 220 221 222 223 484 224 225 226 227 228 229 230 231 485 232 233 234 235 236 237 238 239 486 240 241 242 243 244 245 246 247 487 248 249 250 251 252 253 254 255 488 256>; 489 }; 490 491 clocks { 492 compatible = "simple-bus"; 493 #address-cells = <1>; 494 #size-cells = <0>; 495 496 clk32k_in: clock@0 { 497 compatible = "fixed-clock"; 498 reg = <0>; 499 #clock-cells = <0>; 500 clock-frequency = <32768>; 501 }; 502 }; 503 504 cpus { 505 cpu@0 { 506 vdd-cpu-supply = <&vdd_cpu>; 507 }; 508 }; 509 510 cpus { 511 cpu@0 { 512 vdd-cpu-supply = <&vdd_cpu>; 513 }; 514 }; 515 516 gpio-keys { 517 compatible = "gpio-keys"; 518 519 lid { 520 label = "Lid"; 521 gpios = <&gpio TEGRA_GPIO(R, 4) GPIO_ACTIVE_LOW>; 522 linux,input-type = <5>; 523 linux,code = <KEY_RESERVED>; 524 debounce-interval = <1>; 525 gpio-key,wakeup; 526 }; 527 528 power { 529 label = "Power"; 530 gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>; 531 linux,code = <KEY_POWER>; 532 debounce-interval = <30>; 533 gpio-key,wakeup; 534 }; 535 }; 536 537 regulators { 538 compatible = "simple-bus"; 539 #address-cells = <1>; 540 #size-cells = <0>; 541 542 vdd_mux: regulator@0 { 543 compatible = "regulator-fixed"; 544 reg = <0>; 545 regulator-name = "+VDD_MUX"; 546 regulator-min-microvolt = <12000000>; 547 regulator-max-microvolt = <12000000>; 548 regulator-always-on; 549 regulator-boot-on; 550 }; 551 552 vdd_5v0_sys: regulator@1 { 553 compatible = "regulator-fixed"; 554 reg = <1>; 555 regulator-name = "+5V_SYS"; 556 regulator-min-microvolt = <5000000>; 557 regulator-max-microvolt = <5000000>; 558 regulator-always-on; 559 regulator-boot-on; 560 vin-supply = <&vdd_mux>; 561 }; 562 563 vdd_3v3_sys: regulator@2 { 564 compatible = "regulator-fixed"; 565 reg = <2>; 566 regulator-name = "+3.3V_SYS"; 567 regulator-min-microvolt = <3300000>; 568 regulator-max-microvolt = <3300000>; 569 regulator-always-on; 570 regulator-boot-on; 571 vin-supply = <&vdd_mux>; 572 }; 573 574 vdd_3v3_run: regulator@3 { 575 compatible = "regulator-fixed"; 576 reg = <3>; 577 regulator-name = "+3.3V_RUN"; 578 regulator-min-microvolt = <3300000>; 579 regulator-max-microvolt = <3300000>; 580 regulator-always-on; 581 regulator-boot-on; 582 gpio = <&pmic 1 GPIO_ACTIVE_HIGH>; 583 enable-active-high; 584 vin-supply = <&vdd_3v3_sys>; 585 }; 586 587 vdd_3v3_hdmi: regulator@4 { 588 compatible = "regulator-fixed"; 589 reg = <4>; 590 regulator-name = "+3.3V_AVDD_HDMI_AP_GATED"; 591 regulator-min-microvolt = <3300000>; 592 regulator-max-microvolt = <3300000>; 593 vin-supply = <&vdd_3v3_run>; 594 }; 595 596 vdd_led: regulator@5 { 597 compatible = "regulator-fixed"; 598 reg = <5>; 599 regulator-name = "+VDD_LED"; 600 gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>; 601 enable-active-high; 602 vin-supply = <&vdd_mux>; 603 }; 604 605 vdd_5v0_ts: regulator@6 { 606 compatible = "regulator-fixed"; 607 reg = <6>; 608 regulator-name = "+5V_VDD_TS_SW"; 609 regulator-min-microvolt = <5000000>; 610 regulator-max-microvolt = <5000000>; 611 regulator-boot-on; 612 gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>; 613 enable-active-high; 614 vin-supply = <&vdd_5v0_sys>; 615 }; 616 617 vdd_usb1_vbus: regulator@7 { 618 compatible = "regulator-fixed"; 619 reg = <7>; 620 regulator-name = "+5V_USB_HS"; 621 regulator-min-microvolt = <5000000>; 622 regulator-max-microvolt = <5000000>; 623 gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>; 624 enable-active-high; 625 gpio-open-drain; 626 vin-supply = <&vdd_5v0_sys>; 627 }; 628 629 vdd_usb3_vbus: regulator@8 { 630 compatible = "regulator-fixed"; 631 reg = <8>; 632 regulator-name = "+5V_USB_SS"; 633 regulator-min-microvolt = <5000000>; 634 regulator-max-microvolt = <5000000>; 635 gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>; 636 enable-active-high; 637 gpio-open-drain; 638 vin-supply = <&vdd_5v0_sys>; 639 }; 640 641 vdd_3v3_panel: regulator@9 { 642 compatible = "regulator-fixed"; 643 reg = <9>; 644 regulator-name = "+3.3V_PANEL"; 645 regulator-min-microvolt = <3300000>; 646 regulator-max-microvolt = <3300000>; 647 gpio = <&pmic 4 GPIO_ACTIVE_HIGH>; 648 enable-active-high; 649 vin-supply = <&vdd_3v3_run>; 650 }; 651 652 vdd_3v3_lp0: regulator@10 { 653 compatible = "regulator-fixed"; 654 reg = <10>; 655 regulator-name = "+3.3V_LP0"; 656 regulator-min-microvolt = <3300000>; 657 regulator-max-microvolt = <3300000>; 658 /* 659 * TODO: find a way to wire this up with the USB EHCI 660 * controllers so that it can be enabled on demand. 661 */ 662 regulator-always-on; 663 gpio = <&pmic 2 GPIO_ACTIVE_HIGH>; 664 enable-active-high; 665 vin-supply = <&vdd_3v3_sys>; 666 }; 667 668 vdd_hdmi_pll: regulator@11 { 669 compatible = "regulator-fixed"; 670 reg = <11>; 671 regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL"; 672 regulator-min-microvolt = <1050000>; 673 regulator-max-microvolt = <1050000>; 674 gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_LOW>; 675 vin-supply = <&vdd_1v05_run>; 676 }; 677 678 vdd_5v0_hdmi: regulator@12 { 679 compatible = "regulator-fixed"; 680 reg = <12>; 681 regulator-name = "+5V_HDMI_CON"; 682 regulator-min-microvolt = <5000000>; 683 regulator-max-microvolt = <5000000>; 684 gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>; 685 enable-active-high; 686 vin-supply = <&vdd_5v0_sys>; 687 }; 688 }; 689 690 sound { 691 nvidia,audio-routing = 692 "Headphones", "HPR", 693 "Headphones", "HPL", 694 "Speakers", "SPKR", 695 "Speakers", "SPKL", 696 "Mic Jack", "MICBIAS", 697 "DMICL", "Int Mic", 698 "DMICR", "Int Mic", 699 "IN34", "Mic Jack"; 700 701 nvidia,i2s-controller = <&tegra_i2s1>; 702 nvidia,audio-codec = <&acodec>; 703 704 clocks = <&tegra_car TEGRA124_CLK_PLL_A>, 705 <&tegra_car TEGRA124_CLK_PLL_A_OUT0>, 706 <&tegra_car TEGRA124_CLK_EXTERN1>; 707 clock-names = "pll_a", "pll_a_out0", "mclk"; 708 709 nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(I, 7) GPIO_ACTIVE_HIGH>; 710 nvidia,mic-det-gpios = 711 <&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>; 712 }; 713 714 gpio-restart { 715 compatible = "gpio-restart"; 716 gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>; 717 priority = <200>; 718 }; 719}; 720 721#include "cros-ec-keyboard.dtsi" 722