xref: /openbmc/u-boot/arch/arm/dts/r8a7790-lager.dts (revision 9450ab2b) 
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Device Tree Source for the Lager board
4 *
5 * Copyright (C) 2013-2014 Renesas Solutions Corp.
6 * Copyright (C) 2014 Cogent Embedded, Inc.
7 * Copyright (C) 2015-2016 Renesas Electronics Corporation
8 */
9
10/*
11 * SSI-AK4643
12 *
13 * SW1: 1: AK4643
14 *      2: CN22
15 *      3: ADV7511
16 *
17 * This command is required when Playback/Capture
18 *
19 *	amixer set "LINEOUT Mixer DACL" on
20 *	amixer set "DVC Out" 100%
21 *	amixer set "DVC In" 100%
22 *
23 * You can use Mute
24 *
25 *	amixer set "DVC Out Mute" on
26 *	amixer set "DVC In Mute" on
27 *
28 * You can use Volume Ramp
29 *
30 *	amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
31 *	amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
32 *	amixer set "DVC Out Ramp" on
33 *	aplay xxx.wav &
34 *	amixer set "DVC Out"  80%  // Volume Down
35 *	amixer set "DVC Out" 100%  // Volume Up
36 */
37
38/dts-v1/;
39#include "r8a7790.dtsi"
40#include <dt-bindings/gpio/gpio.h>
41#include <dt-bindings/input/input.h>
42
43/ {
44	model = "Lager";
45	compatible = "renesas,lager", "renesas,r8a7790";
46
47	aliases {
48		serial0 = &scif0;
49		serial1 = &scifa1;
50		i2c8 = &gpioi2c1;
51		i2c9 = &gpioi2c2;
52		i2c10 = &i2cexio0;
53		i2c11 = &i2cexio1;
54		i2c12 = &i2chdmi;
55		i2c13 = &i2cpwr;
56	};
57
58	chosen {
59		bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
60		stdout-path = "serial0:115200n8";
61	};
62
63	memory@40000000 {
64		device_type = "memory";
65		reg = <0 0x40000000 0 0x40000000>;
66	};
67
68	memory@140000000 {
69		device_type = "memory";
70		reg = <1 0x40000000 0 0xc0000000>;
71	};
72
73	lbsc {
74		#address-cells = <1>;
75		#size-cells = <1>;
76	};
77
78	keyboard {
79		compatible = "gpio-keys";
80
81		one {
82			linux,code = <KEY_1>;
83			label = "SW2-1";
84			wakeup-source;
85			debounce-interval = <20>;
86			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
87		};
88		two {
89			linux,code = <KEY_2>;
90			label = "SW2-2";
91			wakeup-source;
92			debounce-interval = <20>;
93			gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
94		};
95		three {
96			linux,code = <KEY_3>;
97			label = "SW2-3";
98			wakeup-source;
99			debounce-interval = <20>;
100			gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
101		};
102		four {
103			linux,code = <KEY_4>;
104			label = "SW2-4";
105			wakeup-source;
106			debounce-interval = <20>;
107			gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
108		};
109	};
110
111	leds {
112		compatible = "gpio-leds";
113		led6 {
114			gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
115		};
116		led7 {
117			gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
118		};
119		led8 {
120			gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;
121		};
122	};
123
124	fixedregulator3v3: regulator-3v3 {
125		compatible = "regulator-fixed";
126		regulator-name = "fixed-3.3V";
127		regulator-min-microvolt = <3300000>;
128		regulator-max-microvolt = <3300000>;
129		regulator-boot-on;
130		regulator-always-on;
131	};
132
133	vcc_sdhi0: regulator-vcc-sdhi0 {
134		compatible = "regulator-fixed";
135
136		regulator-name = "SDHI0 Vcc";
137		regulator-min-microvolt = <3300000>;
138		regulator-max-microvolt = <3300000>;
139
140		gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>;
141		enable-active-high;
142	};
143
144	vccq_sdhi0: regulator-vccq-sdhi0 {
145		compatible = "regulator-gpio";
146
147		regulator-name = "SDHI0 VccQ";
148		regulator-min-microvolt = <1800000>;
149		regulator-max-microvolt = <3300000>;
150
151		gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
152		gpios-states = <1>;
153		states = <3300000 1
154			  1800000 0>;
155	};
156
157	vcc_sdhi2: regulator-vcc-sdhi2 {
158		compatible = "regulator-fixed";
159
160		regulator-name = "SDHI2 Vcc";
161		regulator-min-microvolt = <3300000>;
162		regulator-max-microvolt = <3300000>;
163
164		gpio = <&gpio5 25 GPIO_ACTIVE_HIGH>;
165		enable-active-high;
166	};
167
168	vccq_sdhi2: regulator-vccq-sdhi2 {
169		compatible = "regulator-gpio";
170
171		regulator-name = "SDHI2 VccQ";
172		regulator-min-microvolt = <1800000>;
173		regulator-max-microvolt = <3300000>;
174
175		gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>;
176		gpios-states = <1>;
177		states = <3300000 1
178			  1800000 0>;
179	};
180
181	audio_clock: audio_clock {
182		compatible = "fixed-clock";
183		#clock-cells = <0>;
184		clock-frequency = <11289600>;
185	};
186
187	rsnd_ak4643: sound {
188		compatible = "simple-audio-card";
189
190		simple-audio-card,format = "left_j";
191		simple-audio-card,bitclock-master = <&sndcodec>;
192		simple-audio-card,frame-master = <&sndcodec>;
193
194		sndcpu: simple-audio-card,cpu {
195			sound-dai = <&rcar_sound>;
196		};
197
198		sndcodec: simple-audio-card,codec {
199			sound-dai = <&ak4643>;
200			clocks = <&audio_clock>;
201		};
202	};
203
204	vga-encoder {
205		compatible = "adi,adv7123";
206
207		ports {
208			#address-cells = <1>;
209			#size-cells = <0>;
210
211			port@0 {
212				reg = <0>;
213				adv7123_in: endpoint {
214					remote-endpoint = <&du_out_rgb>;
215				};
216			};
217			port@1 {
218				reg = <1>;
219				adv7123_out: endpoint {
220					remote-endpoint = <&vga_in>;
221				};
222			};
223		};
224	};
225
226	vga {
227		compatible = "vga-connector";
228
229		port {
230			vga_in: endpoint {
231				remote-endpoint = <&adv7123_out>;
232			};
233		};
234	};
235
236	hdmi-in {
237		compatible = "hdmi-connector";
238		type = "a";
239
240		port {
241			hdmi_con_in: endpoint {
242				remote-endpoint = <&adv7612_in>;
243			};
244		};
245	};
246
247	cec_clock: cec-clock {
248		compatible = "fixed-clock";
249		#clock-cells = <0>;
250		clock-frequency = <12000000>;
251	};
252
253	hdmi-out {
254		compatible = "hdmi-connector";
255		type = "a";
256
257		port {
258			hdmi_con_out: endpoint {
259				remote-endpoint = <&adv7511_out>;
260			};
261		};
262	};
263
264	x2_clk: x2-clock {
265		compatible = "fixed-clock";
266		#clock-cells = <0>;
267		clock-frequency = <148500000>;
268	};
269
270	x13_clk: x13-clock {
271		compatible = "fixed-clock";
272		#clock-cells = <0>;
273		clock-frequency = <148500000>;
274	};
275
276	gpioi2c1: i2c-8 {
277		#address-cells = <1>;
278		#size-cells = <0>;
279		compatible = "i2c-gpio";
280		status = "disabled";
281		scl-gpios = <&gpio1 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
282		sda-gpios = <&gpio1 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
283		i2c-gpio,delay-us = <5>;
284	};
285
286	gpioi2c2: i2c-9 {
287		#address-cells = <1>;
288		#size-cells = <0>;
289		compatible = "i2c-gpio";
290		status = "disabled";
291		scl-gpios = <&gpio5 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
292		sda-gpios = <&gpio5 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
293		i2c-gpio,delay-us = <5>;
294	};
295
296	/*
297	 * IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only.
298	 * We use the I2C demuxer, so the desired IP core can be selected at runtime
299	 * depending on the use case (e.g. DMA with IIC0 or slave support with I2C0).
300	 * Note: For testing the I2C slave feature, it is convenient to connect this
301	 * bus with IIC3 on pins 110 (SCL) + 112 (SDA), select I2C0 at runtime, and
302	 * instantiate the slave device at runtime according to the documentation.
303	 * You can then communicate with the slave via IIC3.
304	 *
305	 * IIC0/I2C0 does not appear to support fallback to GPIO.
306	 */
307	i2cexio0: i2c-10 {
308		compatible = "i2c-demux-pinctrl";
309		i2c-parent = <&iic0>, <&i2c0>;
310		i2c-bus-name = "i2c-exio0";
311		#address-cells = <1>;
312		#size-cells = <0>;
313	};
314
315	/*
316	 * IIC1/I2C1 is routed to EXIO connector A, pins 78 (SCL) + 80 (SDA).
317	 * This is similar to the arangement described for i2cexio0 (above)
318	 * with a fallback to GPIO also provided.
319	 */
320	i2cexio1: i2c-11 {
321		compatible = "i2c-demux-pinctrl";
322		i2c-parent = <&iic1>, <&i2c1>, <&gpioi2c1>;
323		i2c-bus-name = "i2c-exio1";
324		#address-cells = <1>;
325		#size-cells = <0>;
326	};
327
328        /*
329         * IIC2 and I2C2 may be switched using pinmux.
330         * A fallback to GPIO is also provided.
331         */
332	i2chdmi: i2c-12 {
333		compatible = "i2c-demux-pinctrl";
334		i2c-parent = <&iic2>, <&i2c2>, <&gpioi2c2>;
335		i2c-bus-name = "i2c-hdmi";
336		#address-cells = <1>;
337		#size-cells = <0>;
338
339		ak4643: codec@12 {
340			compatible = "asahi-kasei,ak4643";
341			#sound-dai-cells = <0>;
342			reg = <0x12>;
343		};
344
345		composite-in@20 {
346			compatible = "adi,adv7180";
347			reg = <0x20>;
348			remote = <&vin1>;
349
350			port {
351				adv7180: endpoint {
352					bus-width = <8>;
353					remote-endpoint = <&vin1ep0>;
354				};
355			};
356		};
357
358		hdmi@39 {
359			compatible = "adi,adv7511w";
360			reg = <0x39>;
361			interrupt-parent = <&gpio1>;
362			interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
363			clocks = <&cec_clock>;
364			clock-names = "cec";
365
366			adi,input-depth = <8>;
367			adi,input-colorspace = "rgb";
368			adi,input-clock = "1x";
369			adi,input-style = <1>;
370			adi,input-justification = "evenly";
371
372			ports {
373				#address-cells = <1>;
374				#size-cells = <0>;
375
376				port@0 {
377					reg = <0>;
378					adv7511_in: endpoint {
379						remote-endpoint = <&lvds0_out>;
380					};
381				};
382
383				port@1 {
384					reg = <1>;
385					adv7511_out: endpoint {
386						remote-endpoint = <&hdmi_con_out>;
387					};
388				};
389			};
390		};
391
392		hdmi-in@4c {
393			compatible = "adi,adv7612";
394			reg = <0x4c>;
395			interrupt-parent = <&gpio1>;
396			interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
397			default-input = <0>;
398
399			ports {
400				#address-cells = <1>;
401				#size-cells = <0>;
402
403				port@0 {
404					reg = <0>;
405					adv7612_in: endpoint {
406						remote-endpoint = <&hdmi_con_in>;
407					};
408				};
409
410				port@2 {
411					reg = <2>;
412					adv7612_out: endpoint {
413						remote-endpoint = <&vin0ep2>;
414					};
415				};
416			};
417		};
418	};
419
420	/*
421	 * IIC3 and I2C3 may be switched using pinmux.
422	 * IIC3/I2C3 does not appear to support fallback to GPIO.
423	 */
424	i2cpwr: i2c-13 {
425		compatible = "i2c-demux-pinctrl";
426		i2c-parent = <&iic3>, <&i2c3>;
427		i2c-bus-name = "i2c-pwr";
428		#address-cells = <1>;
429		#size-cells = <0>;
430
431		pmic@58 {
432			compatible = "dlg,da9063";
433			reg = <0x58>;
434			interrupt-parent = <&irqc0>;
435			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
436			interrupt-controller;
437
438			rtc {
439				compatible = "dlg,da9063-rtc";
440			};
441
442			wdt {
443				compatible = "dlg,da9063-watchdog";
444			};
445		};
446
447		vdd_dvfs: regulator@68 {
448			compatible = "dlg,da9210";
449			reg = <0x68>;
450			interrupt-parent = <&irqc0>;
451			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
452
453			regulator-min-microvolt = <1000000>;
454			regulator-max-microvolt = <1000000>;
455			regulator-boot-on;
456			regulator-always-on;
457		};
458	};
459};
460
461&du {
462	pinctrl-0 = <&du_pins>;
463	pinctrl-names = "default";
464	status = "okay";
465
466	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>,
467		 <&x13_clk>, <&x2_clk>;
468	clock-names = "du.0", "du.1", "du.2", "dclkin.0", "dclkin.1";
469
470	ports {
471		port@0 {
472			endpoint {
473				remote-endpoint = <&adv7123_in>;
474			};
475		};
476	};
477};
478
479&lvds0 {
480	status = "okay";
481
482	ports {
483		port@1 {
484			endpoint {
485				remote-endpoint = <&adv7511_in>;
486			};
487		};
488	};
489};
490
491&lvds1 {
492	status = "okay";
493
494	ports {
495		port@1 {
496			lvds_connector: endpoint {
497			};
498		};
499	};
500};
501
502&extal_clk {
503	clock-frequency = <20000000>;
504};
505
506&pfc {
507	pinctrl-0 = <&scif_clk_pins>;
508	pinctrl-names = "default";
509
510	du_pins: du {
511		groups = "du_rgb666", "du_sync_1", "du_clk_out_0";
512		function = "du";
513	};
514
515	scif0_pins: scif0 {
516		groups = "scif0_data";
517		function = "scif0";
518	};
519
520	scif_clk_pins: scif_clk {
521		groups = "scif_clk";
522		function = "scif_clk";
523	};
524
525	ether_pins: ether {
526		groups = "eth_link", "eth_mdio", "eth_rmii";
527		function = "eth";
528	};
529
530	phy1_pins: phy1 {
531		groups = "intc_irq0";
532		function = "intc";
533	};
534
535	scifa1_pins: scifa1 {
536		groups = "scifa1_data";
537		function = "scifa1";
538	};
539
540	sdhi0_pins: sd0 {
541		groups = "sdhi0_data4", "sdhi0_ctrl";
542		function = "sdhi0";
543		power-source = <3300>;
544	};
545
546	sdhi0_pins_uhs: sd0_uhs {
547		groups = "sdhi0_data4", "sdhi0_ctrl";
548		function = "sdhi0";
549		power-source = <1800>;
550	};
551
552	sdhi2_pins: sd2 {
553		groups = "sdhi2_data4", "sdhi2_ctrl";
554		function = "sdhi2";
555		power-source = <3300>;
556	};
557
558	sdhi2_pins_uhs: sd2_uhs {
559		groups = "sdhi2_data4", "sdhi2_ctrl";
560		function = "sdhi2";
561		power-source = <1800>;
562	};
563
564	mmc1_pins: mmc1 {
565		groups = "mmc1_data8", "mmc1_ctrl";
566		function = "mmc1";
567	};
568
569	qspi_pins: qspi {
570		groups = "qspi_ctrl", "qspi_data4";
571		function = "qspi";
572	};
573
574	msiof1_pins: msiof1 {
575		groups = "msiof1_clk", "msiof1_sync", "msiof1_rx",
576				 "msiof1_tx";
577		function = "msiof1";
578	};
579
580	i2c0_pins: i2c0 {
581		groups = "i2c0";
582		function = "i2c0";
583	};
584
585	iic0_pins: iic0 {
586		groups = "iic0";
587		function = "iic0";
588	};
589
590	i2c1_pins: i2c1 {
591		groups = "i2c1";
592		function = "i2c1";
593	};
594
595	iic1_pins: iic1 {
596		groups = "iic1";
597		function = "iic1";
598	};
599
600	i2c2_pins: i2c2 {
601		groups = "i2c2";
602		function = "i2c2";
603	};
604
605	iic2_pins: iic2 {
606		groups = "iic2";
607		function = "iic2";
608	};
609
610	i2c3_pins: i2c3 {
611		groups = "i2c3";
612		function = "i2c3";
613	};
614
615	iic3_pins: iic3 {
616		groups = "iic3";
617		function = "iic3";
618	};
619
620	hsusb_pins: hsusb {
621		groups = "usb0_ovc_vbus";
622		function = "usb0";
623	};
624
625	usb0_pins: usb0 {
626		groups = "usb0";
627		function = "usb0";
628	};
629
630	usb1_pins: usb1 {
631		groups = "usb1";
632		function = "usb1";
633	};
634
635	usb2_pins: usb2 {
636		groups = "usb2";
637		function = "usb2";
638	};
639
640	vin0_pins: vin0 {
641		groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk";
642		function = "vin0";
643	};
644
645	vin1_pins: vin1 {
646		groups = "vin1_data8", "vin1_clk";
647		function = "vin1";
648	};
649
650	sound_pins: sound {
651		groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data";
652		function = "ssi";
653	};
654
655	sound_clk_pins: sound_clk {
656		groups = "audio_clk_a";
657		function = "audio_clk";
658	};
659};
660
661&ether {
662	pinctrl-0 = <&ether_pins &phy1_pins>;
663	pinctrl-names = "default";
664
665	phy-handle = <&phy1>;
666	renesas,ether-link-active-low;
667	status = "okay";
668
669	phy1: ethernet-phy@1 {
670		reg = <1>;
671		interrupt-parent = <&irqc0>;
672		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
673		micrel,led-mode = <1>;
674	};
675};
676
677&cmt0 {
678	status = "okay";
679};
680
681&mmcif1 {
682	pinctrl-0 = <&mmc1_pins>;
683	pinctrl-names = "default";
684
685	vmmc-supply = <&fixedregulator3v3>;
686	bus-width = <8>;
687	non-removable;
688	status = "okay";
689};
690
691&sata1 {
692	status = "okay";
693};
694
695&qspi {
696	pinctrl-0 = <&qspi_pins>;
697	pinctrl-names = "default";
698
699	status = "okay";
700
701	flash: flash@0 {
702		compatible = "spansion,s25fl512s", "jedec,spi-nor";
703		reg = <0>;
704		spi-max-frequency = <30000000>;
705		spi-tx-bus-width = <4>;
706		spi-rx-bus-width = <4>;
707		spi-cpha;
708		spi-cpol;
709		m25p,fast-read;
710
711		partitions {
712			compatible = "fixed-partitions";
713			#address-cells = <1>;
714			#size-cells = <1>;
715
716			partition@0 {
717				label = "loader";
718				reg = <0x00000000 0x00040000>;
719				read-only;
720			};
721			partition@40000 {
722				label = "user";
723				reg = <0x00040000 0x00400000>;
724				read-only;
725			};
726			partition@440000 {
727				label = "flash";
728				reg = <0x00440000 0x03bc0000>;
729			};
730		};
731	};
732};
733
734&scif0 {
735	pinctrl-0 = <&scif0_pins>;
736	pinctrl-names = "default";
737
738	status = "okay";
739};
740
741&scifa1 {
742	pinctrl-0 = <&scifa1_pins>;
743	pinctrl-names = "default";
744
745	status = "okay";
746};
747
748&scif_clk {
749	clock-frequency = <14745600>;
750};
751
752&msiof1 {
753	pinctrl-0 = <&msiof1_pins>;
754	pinctrl-names = "default";
755
756	status = "okay";
757
758	pmic: pmic@0 {
759		compatible = "renesas,r2a11302ft";
760		reg = <0>;
761		spi-max-frequency = <6000000>;
762		spi-cpol;
763		spi-cpha;
764	};
765};
766
767&sdhi0 {
768	pinctrl-0 = <&sdhi0_pins>;
769	pinctrl-1 = <&sdhi0_pins_uhs>;
770	pinctrl-names = "default", "state_uhs";
771
772	vmmc-supply = <&vcc_sdhi0>;
773	vqmmc-supply = <&vccq_sdhi0>;
774	cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
775	sd-uhs-sdr50;
776	sd-uhs-sdr104;
777	status = "okay";
778};
779
780&sdhi2 {
781	pinctrl-0 = <&sdhi2_pins>;
782	pinctrl-1 = <&sdhi2_pins_uhs>;
783	pinctrl-names = "default", "state_uhs";
784
785	vmmc-supply = <&vcc_sdhi2>;
786	vqmmc-supply = <&vccq_sdhi2>;
787	cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
788	sd-uhs-sdr50;
789	status = "okay";
790};
791
792&cpu0 {
793	cpu0-supply = <&vdd_dvfs>;
794};
795
796&i2c0	{
797	pinctrl-0 = <&i2c0_pins>;
798	pinctrl-names = "i2c-exio0";
799};
800
801&iic0	{
802	pinctrl-0 = <&iic0_pins>;
803	pinctrl-names = "i2c-exio0";
804};
805
806&i2c1	{
807	pinctrl-0 = <&i2c1_pins>;
808	pinctrl-names = "i2c-exio1";
809};
810
811&iic1	{
812	pinctrl-0 = <&iic1_pins>;
813	pinctrl-names = "i2c-exio1";
814};
815
816&i2c2	{
817	pinctrl-0 = <&i2c2_pins>;
818	pinctrl-names = "i2c-hdmi";
819
820	clock-frequency = <100000>;
821};
822
823&iic2	{
824	pinctrl-0 = <&iic2_pins>;
825	pinctrl-names = "i2c-hdmi";
826
827	clock-frequency = <100000>;
828};
829
830&i2c3	{
831	pinctrl-0 = <&i2c3_pins>;
832	pinctrl-names = "i2c-pwr";
833};
834
835&iic3	{
836	pinctrl-0 = <&iic3_pins>;
837	pinctrl-names = "i2c-pwr";
838};
839
840&pci0 {
841	status = "okay";
842	pinctrl-0 = <&usb0_pins>;
843	pinctrl-names = "default";
844};
845
846&pci1 {
847	status = "okay";
848	pinctrl-0 = <&usb1_pins>;
849	pinctrl-names = "default";
850};
851
852&xhci {
853	status = "okay";
854	pinctrl-0 = <&usb2_pins>;
855	pinctrl-names = "default";
856};
857
858&pci2 {
859	status = "okay";
860	pinctrl-0 = <&usb2_pins>;
861	pinctrl-names = "default";
862};
863
864&hsusb {
865	status = "okay";
866	pinctrl-0 = <&hsusb_pins>;
867	pinctrl-names = "default";
868	renesas,enable-gpio = <&gpio5 18 GPIO_ACTIVE_HIGH>;
869};
870
871&usbphy {
872	status = "okay";
873};
874
875/* HDMI video input */
876&vin0 {
877	pinctrl-0 = <&vin0_pins>;
878	pinctrl-names = "default";
879
880	status = "okay";
881
882	port {
883		vin0ep2: endpoint {
884			remote-endpoint = <&adv7612_out>;
885			bus-width = <24>;
886			hsync-active = <0>;
887			vsync-active = <0>;
888			pclk-sample = <1>;
889			data-active = <1>;
890		};
891	};
892};
893
894/* composite video input */
895&vin1 {
896	pinctrl-0 = <&vin1_pins>;
897	pinctrl-names = "default";
898
899	status = "okay";
900
901	port {
902		vin1ep0: endpoint {
903			remote-endpoint = <&adv7180>;
904			bus-width = <8>;
905		};
906	};
907};
908
909&rcar_sound {
910	pinctrl-0 = <&sound_pins &sound_clk_pins>;
911	pinctrl-names = "default";
912
913	/* Single DAI */
914	#sound-dai-cells = <0>;
915
916	status = "okay";
917
918	rcar_sound,dai {
919		dai0 {
920			playback = <&ssi0 &src2 &dvc0>;
921			capture  = <&ssi1 &src3 &dvc1>;
922		};
923	};
924};
925
926&rwdt {
927	timeout-sec = <60>;
928	status = "okay";
929};
930
931&ssi1 {
932	shared-pin;
933};
934