1/*
2 * SAMSUNG Snow board device tree source
3 *
4 * Copyright (c) 2012 Samsung Electronics Co., Ltd.
5 *		http://www.samsung.com
6 *
7 * This program is free software; you can redistribute it and/or modify
8 * it under the terms of the GNU General Public License version 2 as
9 * published by the Free Software Foundation.
10 */
11
12/dts-v1/;
13#include <dt-bindings/gpio/gpio.h>
14#include <dt-bindings/interrupt-controller/irq.h>
15#include <dt-bindings/input/input.h>
16#include "exynos5250.dtsi"
17
18/ {
19	model = "Google Snow";
20	compatible = "google,snow", "samsung,exynos5250", "samsung,exynos5";
21
22	aliases {
23		i2c0 = "/i2c@12C60000";
24		i2c1 = "/i2c@12C70000";
25		i2c2 = "/i2c@12C80000";
26		i2c3 = "/i2c@12C90000";
27		i2c4 = "/i2c@12CA0000";
28		i2c104 = &i2c_104;
29		i2c5 = "/i2c@12CB0000";
30		i2c6 = "/i2c@12CC0000";
31		i2c7 = "/i2c@12CD0000";
32		spi0 = "/spi@12d20000";
33		spi1 = "/spi@12d30000";
34		spi2 = "/spi@12d40000";
35		spi3 = "/spi@131a0000";
36		spi4 = "/spi@131b0000";
37		mmc0 = "/mmc@12200000";
38		mmc1 = "/mmc@12210000";
39		mmc2 = "/mmc@12220000";
40		mmc3 = "/mmc@12230000";
41		serial0 = "/serial@12C30000";
42		console = "/serial@12C30000";
43		i2s = "/sound@3830000";
44	};
45
46        memory {
47		reg = <0x40000000 0x80000000>;
48	};
49
50	chosen {
51		bootargs = "console=tty1";
52		stdout-path = "serial3:115200n8";
53	};
54
55	iram {
56		reg = <0x02020000 0x60000>;
57	};
58
59	config {
60		samsung,bl1-offset = <0x1400>;
61		samsung,bl2-offset = <0x3400>;
62		u-boot-memory = "/memory";
63		u-boot-offset = <0x3e00000 0x100000>;
64	};
65
66	flash {
67		reg = <0 0x100000>;
68		#address-cells = <1>;
69		#size-cells = <1>;
70		pre-boot {
71			label = "bl1 pre-boot";
72			reg = <0 0x2000>;
73			read-only;
74			filename = "e5250.nbl1.bin";
75			type = "blob exynos-bl1";
76			required;
77		};
78
79		spl {
80			label = "bl2 spl";
81			reg = <0x2000 0x4000>;
82			read-only;
83			filename = "bl2.bin";
84			type = "blob exynos-bl2 boot,dtb";
85			payload = "/flash/ro-boot";
86			required;
87		};
88
89		ro-boot {
90			label = "u-boot";
91			reg = <0x6000 0x9a000>;
92			read-only;
93			type = "blob boot,dtb";
94			required;
95		};
96	};
97
98	i2c-arbitrator {
99		compatible = "i2c-arb-gpio-challenge";
100		#address-cells = <1>;
101		#size-cells = <0>;
102
103		i2c-parent = <&{/i2c@12CA0000}>;
104
105		our-claim-gpio = <&gpf0 3 GPIO_ACTIVE_LOW>;
106		their-claim-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>;
107		slew-delay-us = <10>;
108		wait-retry-us = <3000>;
109		wait-free-us = <50000>;
110
111		/* Use ID 104 as a hint that we're on physical bus 4 */
112		i2c_104: i2c@0 {
113			reg = <0>;
114			#address-cells = <1>;
115			#size-cells = <0>;
116
117			battery: sbs-battery@b {
118				compatible = "sbs,sbs-battery";
119				reg = <0xb>;
120				sbs,poll-retry-count = <1>;
121			};
122
123			cros_ec: embedded-controller {
124				compatible = "google,cros-ec-i2c";
125				reg = <0x1e>;
126				interrupts = <6 IRQ_TYPE_NONE>;
127				interrupt-parent = <&gpx1>;
128				wakeup-source;
129				i2c-max-frequency = <100000>;
130				u-boot,i2c-offset-len = <0>;
131				ec-interrupt = <&gpx1 6 GPIO_ACTIVE_LOW>;
132			};
133
134			power-regulator {
135				compatible = "ti,tps65090";
136				reg = <0x48>;
137
138				regulators {
139					dcdc1 {
140						ti,enable-ext-control;
141					};
142					dcdc2 {
143						ti,enable-ext-control;
144					};
145					dcdc3 {
146						ti,enable-ext-control;
147					};
148					fet1: fet1 {
149						regulator-name = "vcd_led";
150						ti,overcurrent-wait = <3>;
151					};
152					tps65090_fet2: fet2 {
153						regulator-name = "video_mid";
154						regulator-always-on;
155						ti,overcurrent-wait = <3>;
156					};
157					fet3 {
158						regulator-name = "wwan_r";
159						regulator-always-on;
160						ti,overcurrent-wait = <3>;
161					};
162					fet4 {
163						regulator-name = "sdcard";
164						ti,overcurrent-wait = <3>;
165					};
166					fet5 {
167						regulator-name = "camout";
168						regulator-always-on;
169						ti,overcurrent-wait = <3>;
170					};
171					fet6: fet6 {
172						regulator-name = "lcd_vdd";
173						ti,overcurrent-wait = <3>;
174					};
175					tps65090_fet7: fet7 {
176						regulator-name = "video_mid_1a";
177						regulator-always-on;
178						ti,overcurrent-wait = <3>;
179					};
180					ldo1 {
181					};
182					ldo2 {
183					};
184				};
185
186				charger {
187					compatible = "ti,tps65090-charger";
188				};
189			};
190		};
191	};
192
193	i2c@12CD0000 {
194		ptn3460: lvds-bridge@20 {
195			compatible = "nxp,ptn3460";
196			reg = <0x20>;
197			sleep-gpios = <&gpy2 5 GPIO_ACTIVE_LOW>;
198			reset-gpios = <&gpx1 5 GPIO_ACTIVE_LOW>;
199			hotplug-gpios = <&gpx0 7 GPIO_ACTIVE_HIGH>;
200			edid-emulation = <5>;
201
202			ports {
203				port@0 {
204					bridge_out: endpoint {
205						remote-endpoint = <&panel_in>;
206					};
207				};
208
209				port@1 {
210					bridge_in: endpoint {
211						remote-endpoint = <&dp_out>;
212					};
213				};
214			};
215		};
216
217		soundcodec@22 {
218			reg = <0x22>;
219			compatible = "maxim,max98095-codec";
220		};
221	};
222
223	i2c@12C90000 {
224		clock-frequency = <100000>;
225		tpm@20 {
226			reg = <0x20>;
227			u-boot,i2c-offset-len = <0>;
228			compatible = "infineon,slb9635tt";
229		};
230	};
231
232	spi@12d30000 {
233		spi-max-frequency = <50000000>;
234		firmware_storage_spi: flash@0 {
235			compatible = "spi-flash";
236			reg = <0>;
237		};
238	};
239
240	backlight: backlight {
241		compatible = "pwm-backlight";
242		pwms = <&pwm 0 1000000 0>;
243		brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
244		default-brightness-level = <7>;
245		enable-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>;
246		power-supply = <&fet1>;
247	};
248
249	panel: panel {
250		compatible = "auo,b116xw03";
251		power-supply = <&fet6>;
252		backlight = <&backlight>;
253
254		port {
255			panel_in: endpoint {
256				remote-endpoint = <&bridge_out>;
257			};
258		};
259	};
260
261	spi@131b0000 {
262		spi-max-frequency = <1000000>;
263		spi-deactivate-delay = <100>;
264
265		/* Snow did support SPI but the released version used I2C */
266		embedded-controller {
267			compatible = "google,cros-ec-i2c";
268			reg = <0x1e>;
269			spi-max-frequency = <5000000>;
270			ec-interrupt = <&gpx1 6 GPIO_ACTIVE_LOW>;
271			optimise-flash-write;
272			status = "disabled";
273		};
274	};
275
276	sound@3830000 {
277		samsung,codec-type = "max98095";
278		codec-enable-gpio = <&gpx1 7 GPIO_ACTIVE_HIGH>;
279	};
280
281	sound@12d60000 {
282		status = "disabled";
283	};
284
285	i2c@12C60000 {
286		max77686@09 {
287			reg = <0x9>;
288			compatible = "maxim,max77686";
289		};
290	};
291
292	mmc@12200000 {
293		samsung,bus-width = <8>;
294		samsung,timing = <1 3 3>;
295		samsung,removable = <0>;
296	};
297
298	mmc@12210000 {
299		status = "disabled";
300	};
301
302	mmc@12220000 {
303		samsung,bus-width = <4>;
304		samsung,timing = <1 2 3>;
305		samsung,removable = <1>;
306	};
307
308	mmc@12230000 {
309		status = "disabled";
310	};
311
312	ehci@12110000 {
313		samsung,vbus-gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>;
314		status = "okay";
315	};
316
317	xhci@12000000 {
318		samsung,vbus-gpio = <&gpx2 7 GPIO_ACTIVE_HIGH>;
319	};
320
321	tmu@10060000 {
322		samsung,min-temp	= <25>;
323		samsung,max-temp	= <125>;
324		samsung,start-warning	= <95>;
325		samsung,start-tripping	= <105>;
326		samsung,hw-tripping	= <110>;
327		samsung,efuse-min-value	= <40>;
328		samsung,efuse-value	= <55>;
329		samsung,efuse-max-value	= <100>;
330		samsung,slope		= <274761730>;
331		samsung,dc-value	= <25>;
332	};
333
334	fimd@14400000 {
335		samsung,vl-freq = <60>;
336		samsung,vl-col = <1366>;
337		samsung,vl-row = <768>;
338		samsung,vl-width = <1366>;
339		samsung,vl-height = <768>;
340
341		samsung,vl-clkp;
342		samsung,vl-dp;
343		samsung,vl-hsp;
344		samsung,vl-vsp;
345
346		samsung,vl-bpix = <4>;
347
348		samsung,vl-hspw = <32>;
349		samsung,vl-hbpd = <80>;
350		samsung,vl-hfpd = <48>;
351		samsung,vl-vspw = <5>;
352		samsung,vl-vbpd = <14>;
353		samsung,vl-vfpd = <3>;
354		samsung,vl-cmd-allow-len = <0xf>;
355
356		samsung,winid = <0>;
357		samsung,interface-mode = <1>;
358		samsung,dp-enabled = <1>;
359		samsung,dual-lcd-enabled = <0>;
360	};
361
362	dp@145b0000 {
363		samsung,lt-status = <0>;
364
365		samsung,master-mode = <0>;
366		samsung,bist-mode = <0>;
367		samsung,bist-pattern = <0>;
368		samsung,h-sync-polarity = <0>;
369		samsung,v-sync-polarity = <0>;
370		samsung,interlaced = <0>;
371		samsung,color-space = <0>;
372		samsung,dynamic-range = <0>;
373		samsung,ycbcr-coeff = <0>;
374		samsung,color-depth = <1>;
375		samsung,hpd-gpio = <&gpx0 7 GPIO_ACTIVE_HIGH>;
376
377		ports {
378			port@0 {
379				dp_out: endpoint {
380					remote-endpoint = <&bridge_in>;
381				};
382			};
383		};
384	};
385
386};
387
388&i2c_0 {
389	status = "okay";
390	samsung,i2c-sda-delay = <100>;
391	samsung,i2c-max-bus-freq = <378000>;
392
393	max77686: max77686@09 {
394		compatible = "maxim,max77686";
395		interrupt-parent = <&gpx3>;
396		interrupts = <2 IRQ_TYPE_NONE>;
397		wakeup-source;
398		reg = <0x09>;
399		#clock-cells = <1>;
400
401		voltage-regulators {
402			ldo1_reg: LDO1 {
403				regulator-name = "P1.0V_LDO_OUT1";
404				regulator-min-microvolt = <1000000>;
405				regulator-max-microvolt = <1000000>;
406				regulator-always-on;
407			};
408
409			ldo2_reg: LDO2 {
410				regulator-name = "P1.8V_LDO_OUT2";
411				regulator-min-microvolt = <1800000>;
412				regulator-max-microvolt = <1800000>;
413				regulator-always-on;
414			};
415
416			ldo3_reg: LDO3 {
417				regulator-name = "P1.8V_LDO_OUT3";
418				regulator-min-microvolt = <1800000>;
419				regulator-max-microvolt = <1800000>;
420				regulator-always-on;
421			};
422
423			ldo7_reg: LDO7 {
424				regulator-name = "P1.1V_LDO_OUT7";
425				regulator-min-microvolt = <1100000>;
426				regulator-max-microvolt = <1100000>;
427				regulator-always-on;
428			};
429
430			ldo8_reg: LDO8 {
431				regulator-name = "P1.0V_LDO_OUT8";
432				regulator-min-microvolt = <1000000>;
433				regulator-max-microvolt = <1000000>;
434				regulator-always-on;
435			};
436
437			ldo10_reg: LDO10 {
438				regulator-name = "P1.8V_LDO_OUT10";
439				regulator-min-microvolt = <1800000>;
440				regulator-max-microvolt = <1800000>;
441				regulator-always-on;
442			};
443
444			ldo12_reg: LDO12 {
445				regulator-name = "P3.0V_LDO_OUT12";
446				regulator-min-microvolt = <3000000>;
447				regulator-max-microvolt = <3000000>;
448				regulator-always-on;
449			};
450
451			ldo14_reg: LDO14 {
452				regulator-name = "P1.8V_LDO_OUT14";
453				regulator-min-microvolt = <1800000>;
454				regulator-max-microvolt = <1800000>;
455				regulator-always-on;
456			};
457
458			ldo15_reg: LDO15 {
459				regulator-name = "P1.0V_LDO_OUT15";
460				regulator-min-microvolt = <1000000>;
461				regulator-max-microvolt = <1000000>;
462				regulator-always-on;
463			};
464
465			ldo16_reg: LDO16 {
466				regulator-name = "P1.8V_LDO_OUT16";
467				regulator-min-microvolt = <1800000>;
468				regulator-max-microvolt = <1800000>;
469				regulator-always-on;
470			};
471
472			ldo17_reg: LDO17 {
473				regulator-name = "vdd_mydp";
474				regulator-min-microvolt = <1200000>;
475				regulator-max-microvolt = <1200000>;
476			};
477
478			buck1_reg: BUCK1 {
479				regulator-name = "vdd_mif";
480				regulator-min-microvolt = <950000>;
481				regulator-max-microvolt = <1300000>;
482				regulator-always-on;
483				regulator-boot-on;
484			};
485
486			buck2_reg: BUCK2 {
487				regulator-name = "vdd_arm";
488				regulator-min-microvolt = <850000>;
489				regulator-max-microvolt = <1350000>;
490				regulator-always-on;
491				regulator-boot-on;
492			};
493
494			buck3_reg: BUCK3 {
495				regulator-name = "vdd_int";
496				regulator-min-microvolt = <900000>;
497				regulator-max-microvolt = <1200000>;
498				regulator-always-on;
499				regulator-boot-on;
500			};
501
502			buck4_reg: BUCK4 {
503				regulator-name = "vdd_g3d";
504				regulator-min-microvolt = <850000>;
505				regulator-max-microvolt = <1300000>;
506				regulator-always-on;
507				regulator-boot-on;
508			};
509
510			buck5_reg: BUCK5 {
511				regulator-name = "P1.8V_BUCK_OUT5";
512				regulator-min-microvolt = <1800000>;
513				regulator-max-microvolt = <1800000>;
514				regulator-always-on;
515				regulator-boot-on;
516			};
517
518			buck6_reg: BUCK6 {
519				regulator-name = "P1.35V_BUCK_OUT6";
520				regulator-min-microvolt = <1350000>;
521				regulator-max-microvolt = <1350000>;
522				regulator-always-on;
523			};
524
525			buck7_reg: BUCK7 {
526				regulator-name = "P2.0V_BUCK_OUT7";
527				regulator-min-microvolt = <2000000>;
528				regulator-max-microvolt = <2000000>;
529				regulator-always-on;
530			};
531
532			buck8_reg: BUCK8 {
533				regulator-name = "P2.85V_BUCK_OUT8";
534				regulator-min-microvolt = <2850000>;
535				regulator-max-microvolt = <2850000>;
536				regulator-always-on;
537			};
538		};
539	};
540};
541
542#include "cros-ec-keyboard.dtsi"
543