1#include <dt-bindings/pinctrl/bcm2835.h> 2#include <dt-bindings/clock/bcm2835.h> 3#include <dt-bindings/clock/bcm2835-aux.h> 4#include <dt-bindings/gpio/gpio.h> 5 6/* firmware-provided startup stubs live here, where the secondary CPUs are 7 * spinning. 8 */ 9/memreserve/ 0x00000000 0x00001000; 10 11/* This include file covers the common peripherals and configuration between 12 * bcm2835 and bcm2836 implementations, leaving the CPU configuration to 13 * bcm2835.dtsi and bcm2836.dtsi. 14 */ 15 16/ { 17 compatible = "brcm,bcm2835"; 18 model = "BCM2835"; 19 interrupt-parent = <&intc>; 20 #address-cells = <1>; 21 #size-cells = <1>; 22 23 chosen { 24 bootargs = "earlyprintk console=ttyAMA0"; 25 }; 26 27 thermal-zones { 28 cpu_thermal: cpu-thermal { 29 polling-delay-passive = <0>; 30 polling-delay = <1000>; 31 32 thermal-sensors = <&thermal>; 33 34 trips { 35 cpu-crit { 36 temperature = <80000>; 37 hysteresis = <0>; 38 type = "critical"; 39 }; 40 }; 41 42 cooling-maps { 43 }; 44 }; 45 }; 46 47 soc: soc { 48 compatible = "simple-bus"; 49 #address-cells = <1>; 50 #size-cells = <1>; 51 52 timer@7e003000 { 53 compatible = "brcm,bcm2835-system-timer"; 54 reg = <0x7e003000 0x1000>; 55 interrupts = <1 0>, <1 1>, <1 2>, <1 3>; 56 /* This could be a reference to BCM2835_CLOCK_TIMER, 57 * but we don't have the driver using the common clock 58 * support yet. 59 */ 60 clock-frequency = <1000000>; 61 }; 62 63 dma: dma@7e007000 { 64 compatible = "brcm,bcm2835-dma"; 65 reg = <0x7e007000 0xf00>; 66 interrupts = <1 16>, 67 <1 17>, 68 <1 18>, 69 <1 19>, 70 <1 20>, 71 <1 21>, 72 <1 22>, 73 <1 23>, 74 <1 24>, 75 <1 25>, 76 <1 26>, 77 /* dma channel 11-14 share one irq */ 78 <1 27>, 79 <1 27>, 80 <1 27>, 81 <1 27>, 82 /* unused shared irq for all channels */ 83 <1 28>; 84 interrupt-names = "dma0", 85 "dma1", 86 "dma2", 87 "dma3", 88 "dma4", 89 "dma5", 90 "dma6", 91 "dma7", 92 "dma8", 93 "dma9", 94 "dma10", 95 "dma11", 96 "dma12", 97 "dma13", 98 "dma14", 99 "dma-shared-all"; 100 #dma-cells = <1>; 101 brcm,dma-channel-mask = <0x7f35>; 102 }; 103 104 intc: interrupt-controller@7e00b200 { 105 compatible = "brcm,bcm2835-armctrl-ic"; 106 reg = <0x7e00b200 0x200>; 107 interrupt-controller; 108 #interrupt-cells = <2>; 109 }; 110 111 watchdog@7e100000 { 112 compatible = "brcm,bcm2835-pm-wdt"; 113 reg = <0x7e100000 0x28>; 114 }; 115 116 clocks: cprman@7e101000 { 117 compatible = "brcm,bcm2835-cprman"; 118 #clock-cells = <1>; 119 reg = <0x7e101000 0x2000>; 120 121 /* CPRMAN derives almost everything from the 122 * platform's oscillator. However, the DSI 123 * pixel clocks come from the DSI analog PHY. 124 */ 125 clocks = <&clk_osc>, 126 <&dsi0 0>, <&dsi0 1>, <&dsi0 2>, 127 <&dsi1 0>, <&dsi1 1>, <&dsi1 2>; 128 }; 129 130 rng@7e104000 { 131 compatible = "brcm,bcm2835-rng"; 132 reg = <0x7e104000 0x10>; 133 }; 134 135 mailbox: mailbox@7e00b880 { 136 compatible = "brcm,bcm2835-mbox"; 137 reg = <0x7e00b880 0x40>; 138 interrupts = <0 1>; 139 #mbox-cells = <0>; 140 }; 141 142 gpio: gpio@7e200000 { 143 compatible = "brcm,bcm2835-gpio"; 144 reg = <0x7e200000 0xb4>; 145 /* 146 * The GPIO IP block is designed for 3 banks of GPIOs. 147 * Each bank has a GPIO interrupt for itself. 148 * There is an overall "any bank" interrupt. 149 * In order, these are GIC interrupts 17, 18, 19, 20. 150 * Since the BCM2835 only has 2 banks, the 2nd bank 151 * interrupt output appears to be mirrored onto the 152 * 3rd bank's interrupt signal. 153 * So, a bank0 interrupt shows up on 17, 20, and 154 * a bank1 interrupt shows up on 18, 19, 20! 155 */ 156 interrupts = <2 17>, <2 18>, <2 19>, <2 20>; 157 158 gpio-controller; 159 #gpio-cells = <2>; 160 161 interrupt-controller; 162 #interrupt-cells = <2>; 163 164 /* Defines pin muxing groups according to 165 * BCM2835-ARM-Peripherals.pdf page 102. 166 * 167 * While each pin can have its mux selected 168 * for various functions individually, some 169 * groups only make sense to switch to a 170 * particular function together. 171 */ 172 dpi_gpio0: dpi_gpio0 { 173 brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11 174 12 13 14 15 16 17 18 19 175 20 21 22 23 24 25 26 27>; 176 brcm,function = <BCM2835_FSEL_ALT2>; 177 }; 178 emmc_gpio22: emmc_gpio22 { 179 brcm,pins = <22 23 24 25 26 27>; 180 brcm,function = <BCM2835_FSEL_ALT3>; 181 }; 182 emmc_gpio34: emmc_gpio34 { 183 brcm,pins = <34 35 36 37 38 39>; 184 brcm,function = <BCM2835_FSEL_ALT3>; 185 brcm,pull = <BCM2835_PUD_OFF 186 BCM2835_PUD_UP 187 BCM2835_PUD_UP 188 BCM2835_PUD_UP 189 BCM2835_PUD_UP 190 BCM2835_PUD_UP>; 191 }; 192 emmc_gpio48: emmc_gpio48 { 193 brcm,pins = <48 49 50 51 52 53>; 194 brcm,function = <BCM2835_FSEL_ALT3>; 195 }; 196 197 gpclk0_gpio4: gpclk0_gpio4 { 198 brcm,pins = <4>; 199 brcm,function = <BCM2835_FSEL_ALT0>; 200 }; 201 gpclk1_gpio5: gpclk1_gpio5 { 202 brcm,pins = <5>; 203 brcm,function = <BCM2835_FSEL_ALT0>; 204 }; 205 gpclk1_gpio42: gpclk1_gpio42 { 206 brcm,pins = <42>; 207 brcm,function = <BCM2835_FSEL_ALT0>; 208 }; 209 gpclk1_gpio44: gpclk1_gpio44 { 210 brcm,pins = <44>; 211 brcm,function = <BCM2835_FSEL_ALT0>; 212 }; 213 gpclk2_gpio6: gpclk2_gpio6 { 214 brcm,pins = <6>; 215 brcm,function = <BCM2835_FSEL_ALT0>; 216 }; 217 gpclk2_gpio43: gpclk2_gpio43 { 218 brcm,pins = <43>; 219 brcm,function = <BCM2835_FSEL_ALT0>; 220 }; 221 222 i2c0_gpio0: i2c0_gpio0 { 223 brcm,pins = <0 1>; 224 brcm,function = <BCM2835_FSEL_ALT0>; 225 }; 226 i2c0_gpio28: i2c0_gpio28 { 227 brcm,pins = <28 29>; 228 brcm,function = <BCM2835_FSEL_ALT0>; 229 }; 230 i2c0_gpio44: i2c0_gpio44 { 231 brcm,pins = <44 45>; 232 brcm,function = <BCM2835_FSEL_ALT1>; 233 }; 234 i2c1_gpio2: i2c1_gpio2 { 235 brcm,pins = <2 3>; 236 brcm,function = <BCM2835_FSEL_ALT0>; 237 }; 238 i2c1_gpio44: i2c1_gpio44 { 239 brcm,pins = <44 45>; 240 brcm,function = <BCM2835_FSEL_ALT2>; 241 }; 242 i2c_slave_gpio18: i2c_slave_gpio18 { 243 brcm,pins = <18 19 20 21>; 244 brcm,function = <BCM2835_FSEL_ALT3>; 245 }; 246 247 jtag_gpio4: jtag_gpio4 { 248 brcm,pins = <4 5 6 12 13>; 249 brcm,function = <BCM2835_FSEL_ALT4>; 250 }; 251 jtag_gpio22: jtag_gpio22 { 252 brcm,pins = <22 23 24 25 26 27>; 253 brcm,function = <BCM2835_FSEL_ALT4>; 254 }; 255 256 pcm_gpio18: pcm_gpio18 { 257 brcm,pins = <18 19 20 21>; 258 brcm,function = <BCM2835_FSEL_ALT0>; 259 }; 260 pcm_gpio28: pcm_gpio28 { 261 brcm,pins = <28 29 30 31>; 262 brcm,function = <BCM2835_FSEL_ALT2>; 263 }; 264 265 pwm0_gpio12: pwm0_gpio12 { 266 brcm,pins = <12>; 267 brcm,function = <BCM2835_FSEL_ALT0>; 268 }; 269 pwm0_gpio18: pwm0_gpio18 { 270 brcm,pins = <18>; 271 brcm,function = <BCM2835_FSEL_ALT5>; 272 }; 273 pwm0_gpio40: pwm0_gpio40 { 274 brcm,pins = <40>; 275 brcm,function = <BCM2835_FSEL_ALT0>; 276 }; 277 pwm1_gpio13: pwm1_gpio13 { 278 brcm,pins = <13>; 279 brcm,function = <BCM2835_FSEL_ALT0>; 280 }; 281 pwm1_gpio19: pwm1_gpio19 { 282 brcm,pins = <19>; 283 brcm,function = <BCM2835_FSEL_ALT5>; 284 }; 285 pwm1_gpio41: pwm1_gpio41 { 286 brcm,pins = <41>; 287 brcm,function = <BCM2835_FSEL_ALT0>; 288 }; 289 pwm1_gpio45: pwm1_gpio45 { 290 brcm,pins = <45>; 291 brcm,function = <BCM2835_FSEL_ALT0>; 292 }; 293 294 sdhost_gpio48: sdhost_gpio48 { 295 brcm,pins = <48 49 50 51 52 53>; 296 brcm,function = <BCM2835_FSEL_ALT0>; 297 }; 298 299 spi0_gpio7: spi0_gpio7 { 300 brcm,pins = <7 8 9 10 11>; 301 brcm,function = <BCM2835_FSEL_ALT0>; 302 }; 303 spi0_gpio35: spi0_gpio35 { 304 brcm,pins = <35 36 37 38 39>; 305 brcm,function = <BCM2835_FSEL_ALT0>; 306 }; 307 spi1_gpio16: spi1_gpio16 { 308 brcm,pins = <16 17 18 19 20 21>; 309 brcm,function = <BCM2835_FSEL_ALT4>; 310 }; 311 spi2_gpio40: spi2_gpio40 { 312 brcm,pins = <40 41 42 43 44 45>; 313 brcm,function = <BCM2835_FSEL_ALT4>; 314 }; 315 316 uart0_gpio14: uart0_gpio14 { 317 brcm,pins = <14 15>; 318 brcm,function = <BCM2835_FSEL_ALT0>; 319 }; 320 /* Separate from the uart0_gpio14 group 321 * because it conflicts with spi1_gpio16, and 322 * people often run uart0 on the two pins 323 * without flow control. 324 */ 325 uart0_ctsrts_gpio16: uart0_ctsrts_gpio16 { 326 brcm,pins = <16 17>; 327 brcm,function = <BCM2835_FSEL_ALT3>; 328 }; 329 uart0_ctsrts_gpio30: uart0_ctsrts_gpio30 { 330 brcm,pins = <30 31>; 331 brcm,function = <BCM2835_FSEL_ALT3>; 332 }; 333 uart0_gpio32: uart0_gpio32 { 334 brcm,pins = <32 33>; 335 brcm,function = <BCM2835_FSEL_ALT3>; 336 }; 337 uart0_gpio36: uart0_gpio36 { 338 brcm,pins = <36 37>; 339 brcm,function = <BCM2835_FSEL_ALT2>; 340 }; 341 uart0_ctsrts_gpio38: uart0_ctsrts_gpio38 { 342 brcm,pins = <38 39>; 343 brcm,function = <BCM2835_FSEL_ALT2>; 344 }; 345 346 uart1_gpio14: uart1_gpio14 { 347 brcm,pins = <14 15>; 348 brcm,function = <BCM2835_FSEL_ALT5>; 349 }; 350 uart1_ctsrts_gpio16: uart1_ctsrts_gpio16 { 351 brcm,pins = <16 17>; 352 brcm,function = <BCM2835_FSEL_ALT5>; 353 }; 354 uart1_gpio32: uart1_gpio32 { 355 brcm,pins = <32 33>; 356 brcm,function = <BCM2835_FSEL_ALT5>; 357 }; 358 uart1_ctsrts_gpio30: uart1_ctsrts_gpio30 { 359 brcm,pins = <30 31>; 360 brcm,function = <BCM2835_FSEL_ALT5>; 361 }; 362 uart1_gpio40: uart1_gpio40 { 363 brcm,pins = <40 41>; 364 brcm,function = <BCM2835_FSEL_ALT5>; 365 }; 366 uart1_ctsrts_gpio42: uart1_ctsrts_gpio42 { 367 brcm,pins = <42 43>; 368 brcm,function = <BCM2835_FSEL_ALT5>; 369 }; 370 }; 371 372 uart0: serial@7e201000 { 373 compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell"; 374 reg = <0x7e201000 0x1000>; 375 interrupts = <2 25>; 376 clocks = <&clocks BCM2835_CLOCK_UART>, 377 <&clocks BCM2835_CLOCK_VPU>; 378 clock-names = "uartclk", "apb_pclk"; 379 arm,primecell-periphid = <0x00241011>; 380 }; 381 382 sdhost: mmc@7e202000 { 383 compatible = "brcm,bcm2835-sdhost"; 384 reg = <0x7e202000 0x100>; 385 interrupts = <2 24>; 386 clocks = <&clocks BCM2835_CLOCK_VPU>; 387 dmas = <&dma 13>; 388 dma-names = "rx-tx"; 389 status = "disabled"; 390 }; 391 392 i2s: i2s@7e203000 { 393 compatible = "brcm,bcm2835-i2s"; 394 reg = <0x7e203000 0x20>, 395 <0x7e101098 0x02>; 396 397 dmas = <&dma 2>, 398 <&dma 3>; 399 dma-names = "tx", "rx"; 400 status = "disabled"; 401 }; 402 403 spi: spi@7e204000 { 404 compatible = "brcm,bcm2835-spi"; 405 reg = <0x7e204000 0x1000>; 406 interrupts = <2 22>; 407 clocks = <&clocks BCM2835_CLOCK_VPU>; 408 #address-cells = <1>; 409 #size-cells = <0>; 410 status = "disabled"; 411 }; 412 413 i2c0: i2c@7e205000 { 414 compatible = "brcm,bcm2835-i2c"; 415 reg = <0x7e205000 0x1000>; 416 interrupts = <2 21>; 417 clocks = <&clocks BCM2835_CLOCK_VPU>; 418 #address-cells = <1>; 419 #size-cells = <0>; 420 status = "disabled"; 421 }; 422 423 pixelvalve@7e206000 { 424 compatible = "brcm,bcm2835-pixelvalve0"; 425 reg = <0x7e206000 0x100>; 426 interrupts = <2 13>; /* pwa0 */ 427 }; 428 429 pixelvalve@7e207000 { 430 compatible = "brcm,bcm2835-pixelvalve1"; 431 reg = <0x7e207000 0x100>; 432 interrupts = <2 14>; /* pwa1 */ 433 }; 434 435 dsi0: dsi@7e209000 { 436 compatible = "brcm,bcm2835-dsi0"; 437 reg = <0x7e209000 0x78>; 438 interrupts = <2 4>; 439 #address-cells = <1>; 440 #size-cells = <0>; 441 #clock-cells = <1>; 442 443 clocks = <&clocks BCM2835_PLLA_DSI0>, 444 <&clocks BCM2835_CLOCK_DSI0E>, 445 <&clocks BCM2835_CLOCK_DSI0P>; 446 clock-names = "phy", "escape", "pixel"; 447 448 clock-output-names = "dsi0_byte", 449 "dsi0_ddr2", 450 "dsi0_ddr"; 451 452 }; 453 454 thermal: thermal@7e212000 { 455 compatible = "brcm,bcm2835-thermal"; 456 reg = <0x7e212000 0x8>; 457 clocks = <&clocks BCM2835_CLOCK_TSENS>; 458 #thermal-sensor-cells = <0>; 459 status = "disabled"; 460 }; 461 462 aux: aux@0x7e215000 { 463 compatible = "brcm,bcm2835-aux"; 464 #clock-cells = <1>; 465 reg = <0x7e215000 0x8>; 466 clocks = <&clocks BCM2835_CLOCK_VPU>; 467 }; 468 469 uart1: serial@7e215040 { 470 compatible = "brcm,bcm2835-aux-uart"; 471 reg = <0x7e215040 0x40>; 472 interrupts = <1 29>; 473 clocks = <&aux BCM2835_AUX_CLOCK_UART>; 474 status = "disabled"; 475 }; 476 477 spi1: spi@7e215080 { 478 compatible = "brcm,bcm2835-aux-spi"; 479 reg = <0x7e215080 0x40>; 480 interrupts = <1 29>; 481 clocks = <&aux BCM2835_AUX_CLOCK_SPI1>; 482 #address-cells = <1>; 483 #size-cells = <0>; 484 status = "disabled"; 485 }; 486 487 spi2: spi@7e2150c0 { 488 compatible = "brcm,bcm2835-aux-spi"; 489 reg = <0x7e2150c0 0x40>; 490 interrupts = <1 29>; 491 clocks = <&aux BCM2835_AUX_CLOCK_SPI2>; 492 #address-cells = <1>; 493 #size-cells = <0>; 494 status = "disabled"; 495 }; 496 497 pwm: pwm@7e20c000 { 498 compatible = "brcm,bcm2835-pwm"; 499 reg = <0x7e20c000 0x28>; 500 clocks = <&clocks BCM2835_CLOCK_PWM>; 501 assigned-clocks = <&clocks BCM2835_CLOCK_PWM>; 502 assigned-clock-rates = <10000000>; 503 #pwm-cells = <2>; 504 status = "disabled"; 505 }; 506 507 sdhci: sdhci@7e300000 { 508 compatible = "brcm,bcm2835-sdhci"; 509 reg = <0x7e300000 0x100>; 510 interrupts = <2 30>; 511 clocks = <&clocks BCM2835_CLOCK_EMMC>; 512 status = "disabled"; 513 }; 514 515 hvs@7e400000 { 516 compatible = "brcm,bcm2835-hvs"; 517 reg = <0x7e400000 0x6000>; 518 interrupts = <2 1>; 519 }; 520 521 dsi1: dsi@7e700000 { 522 compatible = "brcm,bcm2835-dsi1"; 523 reg = <0x7e700000 0x8c>; 524 interrupts = <2 12>; 525 #address-cells = <1>; 526 #size-cells = <0>; 527 #clock-cells = <1>; 528 529 clocks = <&clocks BCM2835_PLLD_DSI1>, 530 <&clocks BCM2835_CLOCK_DSI1E>, 531 <&clocks BCM2835_CLOCK_DSI1P>; 532 clock-names = "phy", "escape", "pixel"; 533 534 clock-output-names = "dsi1_byte", 535 "dsi1_ddr2", 536 "dsi1_ddr"; 537 538 status = "disabled"; 539 }; 540 541 i2c1: i2c@7e804000 { 542 compatible = "brcm,bcm2835-i2c"; 543 reg = <0x7e804000 0x1000>; 544 interrupts = <2 21>; 545 clocks = <&clocks BCM2835_CLOCK_VPU>; 546 #address-cells = <1>; 547 #size-cells = <0>; 548 status = "disabled"; 549 }; 550 551 i2c2: i2c@7e805000 { 552 compatible = "brcm,bcm2835-i2c"; 553 reg = <0x7e805000 0x1000>; 554 interrupts = <2 21>; 555 clocks = <&clocks BCM2835_CLOCK_VPU>; 556 #address-cells = <1>; 557 #size-cells = <0>; 558 status = "disabled"; 559 }; 560 561 vec: vec@7e806000 { 562 compatible = "brcm,bcm2835-vec"; 563 reg = <0x7e806000 0x1000>; 564 clocks = <&clocks BCM2835_CLOCK_VEC>; 565 interrupts = <2 27>; 566 status = "disabled"; 567 }; 568 569 pixelvalve@7e807000 { 570 compatible = "brcm,bcm2835-pixelvalve2"; 571 reg = <0x7e807000 0x100>; 572 interrupts = <2 10>; /* pixelvalve */ 573 }; 574 575 hdmi: hdmi@7e902000 { 576 compatible = "brcm,bcm2835-hdmi"; 577 reg = <0x7e902000 0x600>, 578 <0x7e808000 0x100>; 579 interrupts = <2 8>, <2 9>; 580 ddc = <&i2c2>; 581 clocks = <&clocks BCM2835_PLLH_PIX>, 582 <&clocks BCM2835_CLOCK_HSM>; 583 clock-names = "pixel", "hdmi"; 584 dmas = <&dma 17>; 585 dma-names = "audio-rx"; 586 status = "disabled"; 587 }; 588 589 usb: usb@7e980000 { 590 compatible = "brcm,bcm2835-usb"; 591 reg = <0x7e980000 0x10000>; 592 interrupts = <1 9>; 593 #address-cells = <1>; 594 #size-cells = <0>; 595 clocks = <&clk_usb>; 596 clock-names = "otg"; 597 phys = <&usbphy>; 598 phy-names = "usb2-phy"; 599 }; 600 601 v3d: v3d@7ec00000 { 602 compatible = "brcm,bcm2835-v3d"; 603 reg = <0x7ec00000 0x1000>; 604 interrupts = <1 10>; 605 }; 606 607 vc4: gpu { 608 compatible = "brcm,bcm2835-vc4"; 609 }; 610 }; 611 612 clocks { 613 compatible = "simple-bus"; 614 #address-cells = <1>; 615 #size-cells = <0>; 616 617 /* The oscillator is the root of the clock tree. */ 618 clk_osc: clock@3 { 619 compatible = "fixed-clock"; 620 reg = <3>; 621 #clock-cells = <0>; 622 clock-output-names = "osc"; 623 clock-frequency = <19200000>; 624 }; 625 626 clk_usb: clock@4 { 627 compatible = "fixed-clock"; 628 reg = <4>; 629 #clock-cells = <0>; 630 clock-output-names = "otg"; 631 clock-frequency = <480000000>; 632 }; 633 }; 634 635 usbphy: phy { 636 compatible = "usb-nop-xceiv"; 637 }; 638}; 639 640#include "bcm283x-uboot.dtsi" 641