1/* 2 * Copyright (C) 2016 Derald D. Woods <woods.technical@gmail.com> 3 * 4 * Based on am3517-evm.dts 5 * 6 * This program is free software; you can redistribute it and/or modify 7 * it under the terms of the GNU General Public License version 2 as 8 * published by the Free Software Foundation. 9 */ 10 11/ { 12 cpus { 13 cpu@0 { 14 cpu0-supply = <&vdd_core_reg>; 15 }; 16 }; 17 18 wl12xx_buffer: wl12xx_buf { 19 compatible = "regulator-fixed"; 20 regulator-name = "wl1271_buf"; 21 regulator-min-microvolt = <1800000>; 22 regulator-max-microvolt = <1800000>; 23 pinctrl-names = "default"; 24 pinctrl-0 = <&wl12xx_buffer_pins>; 25 gpio = <&gpio5 1 GPIO_ACTIVE_LOW>; /* gpio 129 */ 26 regulator-always-on; 27 vin-supply = <&vdd_1v8_reg>; 28 }; 29 30 wl12xx_vmmc2: wl12xx_vmmc2 { 31 compatible = "regulator-fixed"; 32 regulator-name = "vwl1271"; 33 regulator-min-microvolt = <1800000>; 34 regulator-max-microvolt = <1800000>; 35 pinctrl-names = "default"; 36 pinctrl-0 = <&wl12xx_wkup_pins>; 37 gpio = <&gpio1 3 GPIO_ACTIVE_HIGH >; /* gpio 3 */ 38 startup-delay-us = <70000>; 39 enable-active-high; 40 regulator-always-on; 41 vin-supply = <&wl12xx_buffer>; 42 }; 43}; 44 45&gpmc { 46 ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */ 47 48 nand@0,0 { 49 compatible = "ti,omap2-nand"; 50 linux,mtd-name = "micron,mt29f4g16abchch"; 51 reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ 52 nand-bus-width = <16>; 53 ti,nand-ecc-opt = "bch8"; 54 gpmc,sync-clk-ps = <0>; 55 gpmc,cs-on-ns = <0>; 56 gpmc,cs-rd-off-ns = <44>; 57 gpmc,cs-wr-off-ns = <44>; 58 gpmc,adv-on-ns = <6>; 59 gpmc,adv-rd-off-ns = <34>; 60 gpmc,adv-wr-off-ns = <44>; 61 gpmc,we-off-ns = <40>; 62 gpmc,oe-off-ns = <54>; 63 gpmc,access-ns = <64>; 64 gpmc,rd-cycle-ns = <82>; 65 gpmc,wr-cycle-ns = <82>; 66 gpmc,wr-access-ns = <40>; 67 gpmc,wr-data-mux-bus-ns = <0>; 68 gpmc,device-width = <2>; 69 #address-cells = <1>; 70 #size-cells = <1>; 71 }; 72}; 73 74&i2c1 { 75 clock-frequency = <400000>; 76 77 s35390a: s35390a@30 { 78 compatible = "sii,s35390a"; 79 reg = <0x30>; 80 81 pinctrl-names = "default"; 82 pinctrl-0 = <&rtc_pins>; 83 interrupts-extended = <&gpio2 23 IRQ_TYPE_EDGE_FALLING>; /* gpio_55 */ 84 }; 85 86 tps: tps65023@48 { 87 compatible = "ti,tps65023"; 88 reg = <0x48>; 89 90 regulators { 91 vdd_core_reg: VDCDC1 { 92 regulator-name = "vdd_core"; 93 regulator-always-on; 94 regulator-min-microvolt = <1200000>; 95 regulator-max-microvolt = <1200000>; 96 }; 97 98 vdd_io_reg: VDCDC2 { 99 regulator-name = "vdd_io"; 100 regulator-always-on; 101 regulator-min-microvolt = <3300000>; 102 regulator-max-microvolt = <3300000>; 103 }; 104 105 vdd_1v8_reg: VDCDC3 { 106 regulator-name = "vdd_1v8"; 107 regulator-always-on; 108 regulator-min-microvolt = <1800000>; 109 regulator-max-microvolt = <1800000>; 110 }; 111 112 vdd_usb18_reg: LDO1 { 113 regulator-name = "vdd_usb18"; 114 regulator-always-on; 115 regulator-min-microvolt = <1800000>; 116 regulator-max-microvolt = <1800000>; 117 }; 118 119 vdd_usb33_reg: LDO2 { 120 regulator-name = "vdd_usb33"; 121 regulator-always-on; 122 regulator-min-microvolt = <3300000>; 123 regulator-max-microvolt = <3300000>; 124 }; 125 }; 126 }; 127 128 touchscreen: tsc2004@4b { 129 compatible = "ti,tsc2004"; 130 reg = <0x4b>; 131 132 vio-supply = <&vdd_io_reg>; 133 134 pinctrl-names = "default"; 135 pinctrl-0 = <&tsc2004_pins>; 136 interrupts-extended = <&gpio3 1 IRQ_TYPE_EDGE_RISING>; /* gpio_65 */ 137 138 touchscreen-fuzz-x = <4>; 139 touchscreen-fuzz-y = <7>; 140 touchscreen-fuzz-pressure = <2>; 141 touchscreen-size-x = <480>; 142 touchscreen-size-y = <272>; 143 touchscreen-max-pressure = <2048>; 144 145 ti,x-plate-ohms = <280>; 146 ti,esd-recovery-timeout-ms = <8000>; 147 }; 148}; 149 150&mmc2 { 151 interrupts-extended = <&intc 86 /* &omap3_pmx_core 0x12c */>; 152 153 status = "okay"; 154 pinctrl-names = "default"; 155 pinctrl-0 = <&mmc2_pins>; 156 vmmc-supply = <&wl12xx_vmmc2>; 157 non-removable; 158 bus-width = <4>; 159 cap-power-off-card; 160 #address-cells = <1>; 161 #size-cells = <0>; 162 wlcore: wlcore@2 { 163 compatible = "ti,wl1271"; 164 reg = <2>; 165 interrupt-parent = <&gpio6>; 166 interrupts = <10 IRQ_TYPE_LEVEL_HIGH>; /* gpio_170 */ 167 ref-clock-frequency = <26000000>; 168 tcxo-clock-frequency = <26000000>; 169 }; 170}; 171 172&uart2 { 173 pinctrl-names = "default"; 174 pinctrl-0 = <&uart2_pins>; 175 176 bluetooth { 177 compatible = "ti,wl1271-st"; 178 enable-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>; /* gpio 56 */ 179 max-speed = <3000000>; 180 }; 181}; 182 183&omap3_pmx_core { 184 185 wl12xx_buffer_pins: pinmux_wl12xx_buffer_pins { 186 pinctrl-single,pins = < 187 OMAP3_CORE1_IOPAD(0x2156, PIN_OUTPUT | MUX_MODE4) /* mmc1_dat7.gpio_129 */ 188 >; 189 }; 190 191 mmc2_pins: pinmux_mmc2_pins { 192 pinctrl-single,pins = < 193 OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc2_clk.mmc2_clk */ 194 OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc2_cmd.mmc2_cmd */ 195 OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc2_dat0.mmc2_dat0 */ 196 OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc2_dat1.mmc2_dat1 */ 197 OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc2_dat2.mmc2_dat2 */ 198 OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc2_dat3.mmc2_dat3 */ 199 OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1) /* mmc2_dat4.mmc2_dir_dat0 */ 200 OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1) /* mmc2_dat5.mmc2_dir_dat1 */ 201 OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1) /* mmc2_dat6.mmc2_dir_cmd */ 202 OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1) /* mmc2_dat7.mmc2_clkin */ 203 OMAP3_CORE1_IOPAD(0x21c6, PIN_INPUT_PULLUP | MUX_MODE4) /* hdq_sio.gpio_170 */ 204 >; 205 }; 206 207 rtc_pins: pinmux_rtc_pins { 208 pinctrl-single,pins = < 209 OMAP3_CORE1_IOPAD(0x20b6, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_ncs4.gpio_55 */ 210 >; 211 }; 212 213 tsc2004_pins: pinmux_tsc2004_pins { 214 pinctrl-single,pins = < 215 OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT | MUX_MODE4) /* gpmc_wait3.gpio_65 */ 216 >; 217 }; 218 219 uart2_pins: pinmux_uart2_pins { 220 pinctrl-single,pins = < 221 OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts */ 222 OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT_PULLUP | MUX_MODE0) /* uart2_rts */ 223 OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx */ 224 OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx */ 225 OMAP3_CORE1_IOPAD(0x20b8, PIN_INPUT | MUX_MODE0) /* gpio_56 */ 226 >; 227 }; 228}; 229 230&omap3_pmx_wkup { 231 232 wl12xx_wkup_pins: pinmux_wl12xx_wkup_pins { 233 pinctrl-single,pins = < 234 OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4) /* sys_boot1.gpio_3 */ 235 >; 236 }; 237}; 238