1#
2# Copyright 2014-2015 Freescale Semiconductor
3#
4# SPDX-License-Identifier:      GPL-2.0+
5#
6
7Freescale LayerScape with Chassis Generation 3
8
9This architecture supports Freescale ARMv8 SoCs with Chassis generation 3,
10for example LS2080A.
11
12DDR Layout
13============
14Entire DDR region splits into two regions.
15 - Region 1 is at address 0x8000_0000 to 0xffff_ffff.
16 - Region 2 is at 0x80_8000_0000 to the top of total memory,
17   for example 16GB, 0x83_ffff_ffff.
18
19All DDR memory is marked as cache-enabled.
20
21When MC and Debug server is enabled, they carve 512MB away from the high
22end of DDR. For example, if the total DDR is 16GB, it shrinks to 15.5GB
23with MC and Debug server enabled. Linux only sees 15.5GB.
24
25The reserved 512MB layout looks like
26
27   +---------------+ <-- top/end of memory
28   |    256MB      |  debug server
29   +---------------+
30   |    256MB      |  MC
31   +---------------+
32   |     ...       |
33
34MC requires the memory to be aligned with 512MB, so even debug server is
35not enabled, 512MB is reserved, not 256MB.
36
37Flash Layout
38============
39
40(1) A typical layout of various images (including Linux and other firmware images)
41   is shown below considering a 32MB NOR flash device present on most
42   pre-silicon platforms (simulator and emulator):
43
44	-------------------------
45	| 	FIT Image	|
46	| (linux + DTB + RFS)	|
47	------------------------- ----> 0x0120_0000
48	| 	Debug Server FW |
49	------------------------- ----> 0x00C0_0000
50	|	AIOP FW 	|
51	------------------------- ----> 0x0070_0000
52	|	MC FW 		|
53	------------------------- ----> 0x006C_0000
54	| 	MC DPL Blob 	|
55	------------------------- ----> 0x0020_0000
56	| 	BootLoader + Env|
57	------------------------- ----> 0x0000_1000
58	|	PBI 		|
59	------------------------- ----> 0x0000_0080
60	|	RCW 		|
61	------------------------- ----> 0x0000_0000
62
63	32-MB NOR flash layout for pre-silicon platforms (simulator and emulator)
64
65(2) A typical layout of various images (including Linux and other firmware images)
66    is shown below considering a 128MB NOR flash device present on QDS and RDB
67    boards:
68	----------------------------------------- ----> 0x5_8800_0000 ---
69	|	.. Unused .. (7M)		|			|
70	----------------------------------------- ----> 0x5_8790_0000	|
71	| FIT Image (linux + DTB + RFS)	(40M)	|			|
72	----------------------------------------- ----> 0x5_8510_0000	|
73	|	PHY firmware (2M)	 	|			|
74	----------------------------------------- ----> 0x5_84F0_0000	| 64K
75	|	Debug Server FW (2M)		|			| Alt
76	----------------------------------------- ----> 0x5_84D0_0000	| Bank
77	|	AIOP FW (4M)			|			|
78	----------------------------------------- ----> 0x5_8490_0000 (vbank4)
79	|	MC DPC Blob (1M) 		|			|
80	----------------------------------------- ----> 0x5_8480_0000	|
81	|	MC DPL Blob (1M)		|			|
82	----------------------------------------- ----> 0x5_8470_0000	|
83	| 	MC FW (4M)			|			|
84	----------------------------------------- ----> 0x5_8430_0000	|
85	|	BootLoader Environment (1M) 	|			|
86	----------------------------------------- ----> 0x5_8420_0000	|
87	|	BootLoader (1M)			|			|
88	----------------------------------------- ----> 0x5_8410_0000	|
89	|	RCW and PBI (1M) 		|			|
90	----------------------------------------- ----> 0x5_8400_0000 ---
91	|	.. Unused .. (7M)		|			|
92	----------------------------------------- ----> 0x5_8390_0000	|
93	| FIT Image (linux + DTB + RFS)	(40M)	|			|
94	----------------------------------------- ----> 0x5_8110_0000	|
95	|	PHY firmware (2M)	 	|			|
96	----------------------------------------- ----> 0x5_80F0_0000	| 64K
97	|	Debug Server FW (2M)		|			| Bank
98	----------------------------------------- ----> 0x5_80D0_0000	|
99	|	AIOP FW (4M)			|			|
100	----------------------------------------- ----> 0x5_8090_0000 (vbank0)
101	|	MC DPC Blob (1M) 		|			|
102	----------------------------------------- ----> 0x5_8080_0000	|
103	|	MC DPL Blob (1M)		|			|
104	----------------------------------------- ----> 0x5_8070_0000	|
105	| 	MC FW (4M)			|			|
106	----------------------------------------- ----> 0x5_8030_0000	|
107	|	BootLoader Environment (1M) 	|			|
108	----------------------------------------- ----> 0x5_8020_0000	|
109	|	BootLoader (1M)			|			|
110	----------------------------------------- ----> 0x5_8010_0000	|
111	|	RCW and PBI (1M) 		|			|
112	----------------------------------------- ----> 0x5_8000_0000 ---
113
114	128-MB NOR flash layout for QDS and RDB boards
115
116Environment Variables
117=====================
118mcboottimeout:	MC boot timeout in milliseconds. If this variable is not defined
119		the value CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS will be assumed.
120
121mcmemsize:	MC DRAM block size. If this variable is not defined, the value
122		CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE will be assumed.
123
124mcinitcmd:	This environment variable is defined to initiate MC and DPL deployment
125		from the location where it is stored(NOR, NAND, SD, SATA, USB)during
126		u-boot booting.If this variable is not defined then MC_BOOT_ENV_VAR
127		will be null and MC will not be booted and DPL will not be applied
128		during U-boot booting.However the MC, DPC and DPL can be applied from
129		console independently.
130		The variable needs to be set from the console once and then on
131		rebooting the parameters set in the variable will automatically be
132		executed. The commmand is demostrated taking an example of mc boot
133		using NOR Flash i.e. MC, DPL, and DPC is stored in the NOR flash:
134
135		cp.b 0xa0000000 0x580300000 $filesize
136		cp.b 0x80000000 0x580800000 $filesize
137		cp.b 0x90000000 0x580700000 $filesize
138
139		setenv mcinitcmd 'fsl_mc start mc 0x580300000 0x580800000'
140
141		If only linux is to be booted then the mcinitcmd environment should be set as
142
143		setenv mcinitcmd 'fsl_mc start mc 0x580300000 0x580800000;fsl_mc apply DPL 0x580700000'
144
145		Here the addresses 0xa0000000, 0x80000000, 0x80000000 are of DDR to where
146		MC binary, DPC binary and DPL binary are stored and 0x580300000, 0x580800000
147		and 0x580700000 are addresses in NOR where these are copied. It is to be
148		noted that these addresses in 'fsl_mc start mc 0x580300000 0x580800000;fsl_mc apply DPL 0x580700000'
149		can be replaced with the addresses of DDR to
150		which these will be copied in case of these binaries being stored in other
151		devices like SATA, USB, NAND, SD etc.
152
153Booting from NAND
154-------------------
155Booting from NAND requires two images, RCW and u-boot-with-spl.bin.
156The difference between NAND boot RCW image and NOR boot image is the PBI
157command sequence. Below is one example for PBI commands for QDS which uses
158NAND device with 2KB/page, block size 128KB.
159
1601) CCSR 4-byte write to 0x00e00404, data=0x00000000
1612) CCSR 4-byte write to 0x00e00400, data=0x1800a000
162The above two commands set bootloc register to 0x00000000_1800a000 where
163the u-boot code will be running in OCRAM.
164
1653) Block Copy: SRC=0x0107, SRC_ADDR=0x00020000, DEST_ADDR=0x1800a000,
166BLOCK_SIZE=0x00014000
167This command copies u-boot image from NAND device into OCRAM. The values need
168to adjust accordingly.
169
170SRC		should match the cfg_rcw_src, the reset config pins. It depends
171		on the NAND device. See reference manual for cfg_rcw_src.
172SRC_ADDR	is the offset of u-boot-with-spl.bin image in NAND device. In
173		the example above, 128KB. For easy maintenance, we put it at
174		the beginning of next block from RCW.
175DEST_ADDR	is fixed at 0x1800a000, matching bootloc set above.
176BLOCK_SIZE	is the size to be copied by PBI.
177
178RCW image should be written to the beginning of NAND device. Example of using
179u-boot command
180
181nand write <rcw image in memory> 0 <size of rcw image>
182
183To form the NAND image, build u-boot with NAND config, for example,
184ls2080aqds_nand_defconfig. The image needed is u-boot-with-spl.bin.
185The u-boot image should be written to match SRC_ADDR, in above example 0x20000.
186
187nand write <u-boot image in memory> 200000 <size of u-boot image>
188
189With these two images in NAND device, the board can boot from NAND.
190
191Another example for RDB boards,
192
1931) CCSR 4-byte write to 0x00e00404, data=0x00000000
1942) CCSR 4-byte write to 0x00e00400, data=0x1800a000
1953) Block Copy: SRC=0x0119, SRC_ADDR=0x00080000, DEST_ADDR=0x1800a000,
196BLOCK_SIZE=0x00014000
197
198nand write <rcw image in memory> 0 <size of rcw image>
199nand write <u-boot image in memory> 80000 <size of u-boot image>
200
201Notice the difference from QDS is SRC, SRC_ADDR and the offset of u-boot image
202to match board NAND device with 4KB/page, block size 512KB.
203
204MMU Translation Tables
205======================
206
207(1) Early MMU Tables:
208
209     Level 0                   Level 1                   Level 2
210------------------        ------------------        ------------------
211| 0x00_0000_0000 | -----> | 0x00_0000_0000 | -----> | 0x00_0000_0000 |
212------------------        ------------------        ------------------
213| 0x80_0000_0000 | --|    | 0x00_4000_0000 |        | 0x00_0020_0000 |
214------------------   |    ------------------        ------------------
215|    invalid     |   |    | 0x00_8000_0000 |        | 0x00_0040_0000 |
216------------------   |    ------------------        ------------------
217                     |    | 0x00_c000_0000 |        | 0x00_0060_0000 |
218                     |    ------------------        ------------------
219                     |    | 0x01_0000_0000 |        | 0x00_0080_0000 |
220                     |    ------------------        ------------------
221                     |            ...                      ...
222                     |    ------------------
223                     |    | 0x05_8000_0000 |  --|
224                     |    ------------------    |
225                     |    | 0x05_c000_0000 |    |
226                     |    ------------------    |
227                     |            ...           |
228                     |    ------------------    |   ------------------
229                     |--> | 0x80_0000_0000 |    |-> | 0x00_3000_0000 |
230                          ------------------        ------------------
231                          | 0x80_4000_0000 |        | 0x00_3020_0000 |
232                          ------------------        ------------------
233                          | 0x80_8000_0000 |        | 0x00_3040_0000 |
234                          ------------------        ------------------
235                          | 0x80_c000_0000 |        | 0x00_3060_0000 |
236                          ------------------        ------------------
237                          | 0x81_0000_0000 |        | 0x00_3080_0000 |
238                          ------------------        ------------------
239			         ...	                   ...
240
241(2) Final MMU Tables:
242
243     Level 0                   Level 1                   Level 2
244------------------        ------------------        ------------------
245| 0x00_0000_0000 | -----> | 0x00_0000_0000 | -----> | 0x00_0000_0000 |
246------------------        ------------------        ------------------
247| 0x80_0000_0000 | --|    | 0x00_4000_0000 |        | 0x00_0020_0000 |
248------------------   |    ------------------        ------------------
249|    invalid     |   |    | 0x00_8000_0000 |        | 0x00_0040_0000 |
250------------------   |    ------------------        ------------------
251                     |    | 0x00_c000_0000 |        | 0x00_0060_0000 |
252                     |    ------------------        ------------------
253                     |    | 0x01_0000_0000 |        | 0x00_0080_0000 |
254                     |    ------------------        ------------------
255                     |            ...                      ...
256                     |    ------------------
257                     |    | 0x08_0000_0000 | --|
258                     |    ------------------   |
259                     |    | 0x08_4000_0000 |   |
260                     |    ------------------   |
261                     |            ...          |
262                     |    ------------------   |    ------------------
263                     |--> | 0x80_0000_0000 |   |--> | 0x08_0000_0000 |
264                          ------------------        ------------------
265                          | 0x80_4000_0000 |        | 0x08_0020_0000 |
266                          ------------------        ------------------
267                          | 0x80_8000_0000 |        | 0x08_0040_0000 |
268                          ------------------        ------------------
269                          | 0x80_c000_0000 |        | 0x08_0060_0000 |
270                          ------------------        ------------------
271                          | 0x81_0000_0000 |        | 0x08_0080_0000 |
272                          ------------------        ------------------
273			         ...	                   ...
274
275
276DPAA2 commands to manage Management Complex (MC)
277------------------------------------------------
278DPAA2 commands has been introduced to manage Management Complex
279(MC). These commands are used to start mc, aiop and apply DPL
280from u-boot command prompt.
281
282Please note Management complex Firmware(MC), DPL and DPC are no
283more deployed during u-boot boot-sequence.
284
285Commands:
286a) fsl_mc start mc <FW_addr> <DPC_addr> - Start Management Complex
287b) fsl_mc apply DPL <DPL_addr> - Apply DPL file
288c) fsl_mc start aiop <FW_addr> - Start AIOP
289
290How to use commands :-
2911. Command sequence for u-boot ethernet:
292   a) fsl_mc start mc <FW_addr> <DPC_addr> - Start Management Complex
293   b) DPMAC net-devices are now available for use
294
295   Example-
296	Assumption: MC firmware, DPL and DPC dtb is already programmed
297	on NOR flash.
298
299	=> fsl_mc start mc 580300000 580800000
300	=> setenv ethact DPMAC1@xgmii
301	=> ping $serverip
302
3032. Command sequence for Linux boot:
304   a) fsl_mc start mc <FW_addr> <DPC_addr> - Start Management Complex
305   b) fsl_mc apply DPL <DPL_addr> - Apply DPL file
306   c) No DPMAC net-devices are available for use in u-boot
307   d) boot Linux
308
309   Example-
310	Assumption: MC firmware, DPL and DPC dtb is already programmed
311	on NOR flash.
312
313	=> fsl_mc start mc 580300000 580800000
314	=> setenv ethact DPMAC1@xgmii
315	=> tftp a0000000 kernel.itb
316	=> fsl_mc apply dpl 580700000
317	=> bootm a0000000
318
3193. Command sequence for AIOP boot:
320   a) fsl_mc start mc <FW_addr> <DPC_addr> - Start Management Complex
321   b) fsl_mc start aiop <FW_addr> - Start AIOP
322   c) fsl_mc apply DPL <DPL_addr> - Apply DPL file
323   d) No DPMAC net-devices are availabe for use in u-boot
324  Please note actual AIOP start will happen during DPL parsing of
325  Management complex
326
327  Example-
328	Assumption: MC firmware, DPL, DPC dtb and AIOP firmware is already
329	programmed on NOR flash.
330
331	=> fsl_mc start mc 580300000 580800000
332	=> fsl_mc start aiop 0x580900000
333	=> setenv ethact DPMAC1@xgmii
334	=> fsl_mc apply dpl 580700000
335
336Errata A009635
337---------------
338If the core runs at higher than x3 speed of the platform, there is
339possiblity about sev instruction to getting missed by other cores.
340This is because of SoC Run Control block may not able to sample
341the EVENTI(Sev) signals.
342
343Workaround: Configure Run Control and EPU to periodically send out EVENTI signals to
344wake up A57 cores
345
346Errata workaround uses Env variable "a009635_interval_val". It uses decimal
347value.
348- Default value of env variable is platform clock (MHz)
349
350- User can modify default value by updating the env variable
351  setenv a009635_interval_val 600; saveenv;
352  It configure platform clock as 600 MHz
353
354- Env variable as 0 signifies no workaround
355