1config ARCH_LS1012A 2 bool 3 select ARMV8_SET_SMPEN 4 select FSL_LSCH2 5 select SYS_FSL_DDR_BE 6 select SYS_FSL_MMDC 7 select SYS_FSL_ERRATUM_A010315 8 select ARCH_EARLY_INIT_R 9 select BOARD_EARLY_INIT_F 10 11config ARCH_LS1043A 12 bool 13 select ARMV8_SET_SMPEN 14 select FSL_LSCH2 15 select SYS_FSL_DDR 16 select SYS_FSL_DDR_BE 17 select SYS_FSL_DDR_VER_50 18 select SYS_FSL_ERRATUM_A008850 19 select SYS_FSL_ERRATUM_A009660 20 select SYS_FSL_ERRATUM_A009663 21 select SYS_FSL_ERRATUM_A009929 22 select SYS_FSL_ERRATUM_A009942 23 select SYS_FSL_ERRATUM_A010315 24 select SYS_FSL_ERRATUM_A010539 25 select SYS_FSL_HAS_DDR3 26 select SYS_FSL_HAS_DDR4 27 select ARCH_EARLY_INIT_R 28 select BOARD_EARLY_INIT_F 29 30config ARCH_LS1046A 31 bool 32 select ARMV8_SET_SMPEN 33 select FSL_LSCH2 34 select SYS_FSL_DDR 35 select SYS_FSL_DDR_BE 36 select SYS_FSL_DDR_VER_50 37 select SYS_FSL_ERRATUM_A008336 38 select SYS_FSL_ERRATUM_A008511 39 select SYS_FSL_ERRATUM_A009801 40 select SYS_FSL_ERRATUM_A009803 41 select SYS_FSL_ERRATUM_A009942 42 select SYS_FSL_ERRATUM_A010165 43 select SYS_FSL_ERRATUM_A010539 44 select SYS_FSL_HAS_DDR4 45 select SYS_FSL_SRDS_2 46 select ARCH_EARLY_INIT_R 47 select BOARD_EARLY_INIT_F 48 49config ARCH_LS2080A 50 bool 51 select ARMV8_SET_SMPEN 52 select ARM_ERRATA_826974 53 select ARM_ERRATA_828024 54 select ARM_ERRATA_829520 55 select ARM_ERRATA_833471 56 select FSL_LSCH3 57 select SYS_FSL_DDR 58 select SYS_FSL_DDR_LE 59 select SYS_FSL_DDR_VER_50 60 select SYS_FSL_HAS_DP_DDR 61 select SYS_FSL_HAS_SEC 62 select SYS_FSL_HAS_DDR4 63 select SYS_FSL_SEC_COMPAT_5 64 select SYS_FSL_SEC_LE 65 select SYS_FSL_SRDS_2 66 select SYS_FSL_ERRATUM_A008336 67 select SYS_FSL_ERRATUM_A008511 68 select SYS_FSL_ERRATUM_A008514 69 select SYS_FSL_ERRATUM_A008585 70 select SYS_FSL_ERRATUM_A009635 71 select SYS_FSL_ERRATUM_A009663 72 select SYS_FSL_ERRATUM_A009801 73 select SYS_FSL_ERRATUM_A009803 74 select SYS_FSL_ERRATUM_A009942 75 select SYS_FSL_ERRATUM_A010165 76 select SYS_FSL_ERRATUM_A009203 77 select ARCH_EARLY_INIT_R 78 select BOARD_EARLY_INIT_F 79 80config FSL_LSCH2 81 bool 82 select SYS_FSL_HAS_SEC 83 select SYS_FSL_SEC_COMPAT_5 84 select SYS_FSL_SEC_BE 85 select SYS_FSL_SRDS_1 86 select SYS_HAS_SERDES 87 88config FSL_LSCH3 89 bool 90 select SYS_FSL_SRDS_1 91 select SYS_HAS_SERDES 92 93config FSL_MC_ENET 94 bool "Management Complex network" 95 depends on ARCH_LS2080A 96 default y 97 select RESV_RAM 98 help 99 Enable Management Complex (MC) network 100 101menu "Layerscape architecture" 102 depends on FSL_LSCH2 || FSL_LSCH3 103 104config FSL_PCIE_COMPAT 105 string "PCIe compatible of Kernel DT" 106 depends on PCIE_LAYERSCAPE 107 default "fsl,ls1012a-pcie" if ARCH_LS1012A 108 default "fsl,ls1043a-pcie" if ARCH_LS1043A 109 default "fsl,ls1046a-pcie" if ARCH_LS1046A 110 default "fsl,ls2080a-pcie" if ARCH_LS2080A 111 help 112 This compatible is used to find pci controller node in Kernel DT 113 to complete fixup. 114 115config HAS_FEATURE_GIC64K_ALIGN 116 bool 117 default y if ARCH_LS1043A 118 119config HAS_FEATURE_ENHANCED_MSI 120 bool 121 default y if ARCH_LS1043A 122 123menu "Layerscape PPA" 124config FSL_LS_PPA 125 bool "FSL Layerscape PPA firmware support" 126 depends on !ARMV8_PSCI 127 select ARMV8_SEC_FIRMWARE_SUPPORT 128 select SEC_FIRMWARE_ARMV8_PSCI 129 select ARMV8_SEC_FIRMWARE_ERET_ADDR_REVERT if FSL_LSCH2 130 help 131 The FSL Primary Protected Application (PPA) is a software component 132 which is loaded during boot stage, and then remains resident in RAM 133 and runs in the TrustZone after boot. 134 Say y to enable it. 135choice 136 prompt "FSL Layerscape PPA firmware loading-media select" 137 depends on FSL_LS_PPA 138 default SYS_LS_PPA_FW_IN_MMC if SD_BOOT 139 default SYS_LS_PPA_FW_IN_NAND if NAND_BOOT 140 default SYS_LS_PPA_FW_IN_XIP 141 142config SYS_LS_PPA_FW_IN_XIP 143 bool "XIP" 144 help 145 Say Y here if the PPA firmware locate at XIP flash, such 146 as NOR or QSPI flash. 147 148config SYS_LS_PPA_FW_IN_MMC 149 bool "eMMC or SD Card" 150 help 151 Say Y here if the PPA firmware locate at eMMC/SD card. 152 153config SYS_LS_PPA_FW_IN_NAND 154 bool "NAND" 155 help 156 Say Y here if the PPA firmware locate at NAND flash. 157 158endchoice 159 160config SYS_LS_PPA_FW_ADDR 161 hex "Address of PPA firmware loading from" 162 depends on FSL_LS_PPA 163 default 0x40500000 if SYS_LS_PPA_FW_IN_XIP && QSPI_BOOT 164 default 0x580a00000 if SYS_LS_PPA_FW_IN_XIP && ARCH_LS2080A 165 default 0x60500000 if SYS_LS_PPA_FW_IN_XIP 166 default 0x500000 if SYS_LS_PPA_FW_IN_MMC 167 default 0x500000 if SYS_LS_PPA_FW_IN_NAND 168 169 help 170 If the PPA firmware locate at XIP flash, such as NOR or 171 QSPI flash, this address is a directly memory-mapped. 172 If it is in a serial accessed flash, such as NAND and SD 173 card, it is a byte offset. 174 175config SYS_LS_PPA_ESBC_ADDR 176 hex "hdr address of PPA firmware loading from" 177 depends on FSL_LS_PPA && CHAIN_OF_TRUST 178 default 0x600c0000 if SYS_LS_PPA_FW_IN_XIP && ARCH_LS1043A 179 default 0x40740000 if SYS_LS_PPA_FW_IN_XIP && ARCH_LS1046A 180 default 0x580c40000 if SYS_LS_PPA_FW_IN_XIP && FSL_LSCH3 181 help 182 If the PPA header firmware locate at XIP flash, such as NOR or 183 QSPI flash, this address is a directly memory-mapped. 184 If it is in a serial accessed flash, such as NAND and SD 185 card, it is a byte offset. 186 187endmenu 188 189config SYS_FSL_ERRATUM_A010315 190 bool "Workaround for PCIe erratum A010315" 191 192config SYS_FSL_ERRATUM_A010539 193 bool "Workaround for PIN MUX erratum A010539" 194 195config MAX_CPUS 196 int "Maximum number of CPUs permitted for Layerscape" 197 default 4 if ARCH_LS1043A 198 default 4 if ARCH_LS1046A 199 default 16 if ARCH_LS2080A 200 default 1 201 help 202 Set this number to the maximum number of possible CPUs in the SoC. 203 SoCs may have multiple clusters with each cluster may have multiple 204 ports. If some ports are reserved but higher ports are used for 205 cores, count the reserved ports. This will allocate enough memory 206 in spin table to properly handle all cores. 207 208config SECURE_BOOT 209 bool "Secure Boot" 210 help 211 Enable Freescale Secure Boot feature 212 213config QSPI_AHB_INIT 214 bool "Init the QSPI AHB bus" 215 help 216 The default setting for QSPI AHB bus just support 3bytes addressing. 217 But some QSPI flash size up to 64MBytes, so initialize the QSPI AHB 218 bus for those flashes to support the full QSPI flash size. 219 220config SYS_FSL_IFC_BANK_COUNT 221 int "Maximum banks of Integrated flash controller" 222 depends on ARCH_LS1043A || ARCH_LS1046A || ARCH_LS2080A 223 default 4 if ARCH_LS1043A 224 default 4 if ARCH_LS1046A 225 default 8 if ARCH_LS2080A 226 227config SYS_FSL_HAS_DP_DDR 228 bool 229 230config SYS_FSL_SRDS_1 231 bool 232 233config SYS_FSL_SRDS_2 234 bool 235 236config SYS_HAS_SERDES 237 bool 238 239endmenu 240 241menu "Layerscape clock tree configuration" 242 depends on FSL_LSCH2 || FSL_LSCH3 243 244config SYS_FSL_CLK 245 bool "Enable clock tree initialization" 246 default y 247 248config CLUSTER_CLK_FREQ 249 int "Reference clock of core cluster" 250 depends on ARCH_LS1012A 251 default 100000000 252 help 253 This number is the reference clock frequency of core PLL. 254 For most platforms, the core PLL and Platform PLL have the same 255 reference clock, but for some platforms, LS1012A for instance, 256 they are provided sepatately. 257 258config SYS_FSL_PCLK_DIV 259 int "Platform clock divider" 260 default 1 if ARCH_LS1043A 261 default 1 if ARCH_LS1046A 262 default 2 263 help 264 This is the divider that is used to derive Platform clock from 265 Platform PLL, in another word: 266 Platform_clk = Platform_PLL_freq / this_divider 267 268config SYS_FSL_DSPI_CLK_DIV 269 int "DSPI clock divider" 270 default 1 if ARCH_LS1043A 271 default 2 272 help 273 This is the divider that is used to derive DSPI clock from Platform 274 PLL, in another word DSPI_clk = Platform_PLL_freq / this_divider. 275 276config SYS_FSL_DUART_CLK_DIV 277 int "DUART clock divider" 278 default 1 if ARCH_LS1043A 279 default 2 280 help 281 This is the divider that is used to derive DUART clock from Platform 282 clock, in another word DUART_clk = Platform_clk / this_divider. 283 284config SYS_FSL_I2C_CLK_DIV 285 int "I2C clock divider" 286 default 1 if ARCH_LS1043A 287 default 2 288 help 289 This is the divider that is used to derive I2C clock from Platform 290 clock, in another word I2C_clk = Platform_clk / this_divider. 291 292config SYS_FSL_IFC_CLK_DIV 293 int "IFC clock divider" 294 default 1 if ARCH_LS1043A 295 default 2 296 help 297 This is the divider that is used to derive IFC clock from Platform 298 clock, in another word IFC_clk = Platform_clk / this_divider. 299 300config SYS_FSL_LPUART_CLK_DIV 301 int "LPUART clock divider" 302 default 1 if ARCH_LS1043A 303 default 2 304 help 305 This is the divider that is used to derive LPUART clock from Platform 306 clock, in another word LPUART_clk = Platform_clk / this_divider. 307 308config SYS_FSL_SDHC_CLK_DIV 309 int "SDHC clock divider" 310 default 1 if ARCH_LS1043A 311 default 1 if ARCH_LS1012A 312 default 2 313 help 314 This is the divider that is used to derive SDHC clock from Platform 315 clock, in another word SDHC_clk = Platform_clk / this_divider. 316endmenu 317 318config RESV_RAM 319 bool 320 help 321 Reserve memory from the top, tracked by gd->arch.resv_ram. This 322 reserved RAM can be used by special driver that resides in memory 323 after U-Boot exits. It's up to implementation to allocate and allow 324 access to this reserved memory. For example, the reserved RAM can 325 be at the high end of physical memory. The reserve RAM may be 326 excluded from memory bank(s) passed to OS, or marked as reserved. 327 328config SYS_FSL_ERRATUM_A008336 329 bool 330 331config SYS_FSL_ERRATUM_A008514 332 bool 333 334config SYS_FSL_ERRATUM_A008585 335 bool 336 337config SYS_FSL_ERRATUM_A008850 338 bool 339 340config SYS_FSL_ERRATUM_A009203 341 bool 342 343config SYS_FSL_ERRATUM_A009635 344 bool 345 346config SYS_FSL_ERRATUM_A009660 347 bool 348 349config SYS_FSL_ERRATUM_A009929 350 bool 351 352config SYS_MC_RSV_MEM_ALIGN 353 hex "Management Complex reserved memory alignment" 354 depends on RESV_RAM 355 default 0x20000000 356 help 357 Reserved memory needs to be aligned for MC to use. Default value 358 is 512MB. 359