1 /* 2 * (C) Copyright 2013 3 * Andre Przywara, Linaro <andre.przywara@linaro.org> 4 * 5 * Routines to transition ARMv7 processors from secure into non-secure state 6 * and from non-secure SVC into HYP mode 7 * needed to enable ARMv7 virtualization for current hypervisors 8 * 9 * SPDX-License-Identifier: GPL-2.0+ 10 */ 11 12 #include <common.h> 13 #include <asm/armv7.h> 14 #include <asm/gic.h> 15 #include <asm/io.h> 16 #include <asm/secure.h> 17 18 static unsigned int read_id_pfr1(void) 19 { 20 unsigned int reg; 21 22 asm("mrc p15, 0, %0, c0, c1, 1\n" : "=r"(reg)); 23 return reg; 24 } 25 26 static unsigned long get_gicd_base_address(void) 27 { 28 #ifdef CONFIG_ARM_GIC_BASE_ADDRESS 29 return CONFIG_ARM_GIC_BASE_ADDRESS + GIC_DIST_OFFSET; 30 #else 31 unsigned periphbase; 32 33 /* get the GIC base address from the CBAR register */ 34 asm("mrc p15, 4, %0, c15, c0, 0\n" : "=r" (periphbase)); 35 36 /* the PERIPHBASE can be mapped above 4 GB (lower 8 bits used to 37 * encode this). Bail out here since we cannot access this without 38 * enabling paging. 39 */ 40 if ((periphbase & 0xff) != 0) { 41 printf("nonsec: PERIPHBASE is above 4 GB, no access.\n"); 42 return -1; 43 } 44 45 return (periphbase & CBAR_MASK) + GIC_DIST_OFFSET; 46 #endif 47 } 48 49 static void relocate_secure_section(void) 50 { 51 #ifdef CONFIG_ARMV7_SECURE_BASE 52 size_t sz = __secure_end - __secure_start; 53 54 memcpy((void *)CONFIG_ARMV7_SECURE_BASE, __secure_start, sz); 55 flush_dcache_range(CONFIG_ARMV7_SECURE_BASE, 56 CONFIG_ARMV7_SECURE_BASE + sz + 1); 57 invalidate_icache_all(); 58 #endif 59 } 60 61 static void kick_secondary_cpus_gic(unsigned long gicdaddr) 62 { 63 /* kick all CPUs (except this one) by writing to GICD_SGIR */ 64 writel(1U << 24, gicdaddr + GICD_SGIR); 65 } 66 67 void __weak smp_kick_all_cpus(void) 68 { 69 unsigned long gic_dist_addr; 70 71 gic_dist_addr = get_gicd_base_address(); 72 if (gic_dist_addr == -1) 73 return; 74 75 kick_secondary_cpus_gic(gic_dist_addr); 76 } 77 78 int armv7_init_nonsec(void) 79 { 80 unsigned int reg; 81 unsigned itlinesnr, i; 82 unsigned long gic_dist_addr; 83 84 /* check whether the CPU supports the security extensions */ 85 reg = read_id_pfr1(); 86 if ((reg & 0xF0) == 0) { 87 printf("nonsec: Security extensions not implemented.\n"); 88 return -1; 89 } 90 91 /* the SCR register will be set directly in the monitor mode handler, 92 * according to the spec one should not tinker with it in secure state 93 * in SVC mode. Do not try to read it once in non-secure state, 94 * any access to it will trap. 95 */ 96 97 gic_dist_addr = get_gicd_base_address(); 98 if (gic_dist_addr == -1) 99 return -1; 100 101 /* enable the GIC distributor */ 102 writel(readl(gic_dist_addr + GICD_CTLR) | 0x03, 103 gic_dist_addr + GICD_CTLR); 104 105 /* TYPER[4:0] contains an encoded number of available interrupts */ 106 itlinesnr = readl(gic_dist_addr + GICD_TYPER) & 0x1f; 107 108 /* set all bits in the GIC group registers to one to allow access 109 * from non-secure state. The first 32 interrupts are private per 110 * CPU and will be set later when enabling the GIC for each core 111 */ 112 for (i = 1; i <= itlinesnr; i++) 113 writel((unsigned)-1, gic_dist_addr + GICD_IGROUPRn + 4 * i); 114 115 /* 116 * Relocate secure section before any cpu runs in secure ram. 117 * smp_kick_all_cpus may enable other cores and runs into secure 118 * ram, so need to relocate secure section before enabling other 119 * cores. 120 */ 121 relocate_secure_section(); 122 123 #ifndef CONFIG_ARMV7_PSCI 124 smp_set_core_boot_addr((unsigned long)secure_ram_addr(_smp_pen), -1); 125 smp_kick_all_cpus(); 126 #endif 127 128 /* call the non-sec switching code on this CPU also */ 129 secure_ram_addr(_nonsec_init)(); 130 return 0; 131 } 132