1/* SPDX-License-Identifier: GPL-2.0+ */ 2/* 3 * armboot - Startup Code for OMAP3530/ARM Cortex CPU-core 4 * 5 * Copyright (c) 2004 Texas Instruments <r-woodruff2@ti.com> 6 * 7 * Copyright (c) 2001 Marius Gröger <mag@sysgo.de> 8 * Copyright (c) 2002 Alex Züpke <azu@sysgo.de> 9 * Copyright (c) 2002 Gary Jennejohn <garyj@denx.de> 10 * Copyright (c) 2003 Richard Woodruff <r-woodruff2@ti.com> 11 * Copyright (c) 2003 Kshitij <kshitij@ti.com> 12 * Copyright (c) 2006-2008 Syed Mohammed Khasim <x0khasim@ti.com> 13 */ 14 15#include <asm-offsets.h> 16#include <config.h> 17#include <asm/system.h> 18#include <linux/linkage.h> 19#include <asm/armv7.h> 20 21/************************************************************************* 22 * 23 * Startup Code (reset vector) 24 * 25 * Do important init only if we don't start from memory! 26 * Setup memory and board specific bits prior to relocation. 27 * Relocate armboot to ram. Setup stack. 28 * 29 *************************************************************************/ 30 31 .globl reset 32 .globl save_boot_params_ret 33 .type save_boot_params_ret,%function 34#ifdef CONFIG_ARMV7_LPAE 35 .global switch_to_hypervisor_ret 36#endif 37 38reset: 39 /* Allow the board to save important registers */ 40 b save_boot_params 41save_boot_params_ret: 42#ifdef CONFIG_ARMV7_LPAE 43/* 44 * check for Hypervisor support 45 */ 46 mrc p15, 0, r0, c0, c1, 1 @ read ID_PFR1 47 and r0, r0, #CPUID_ARM_VIRT_MASK @ mask virtualization bits 48 cmp r0, #(1 << CPUID_ARM_VIRT_SHIFT) 49 beq switch_to_hypervisor 50switch_to_hypervisor_ret: 51#endif 52 /* 53 * disable interrupts (FIQ and IRQ), also set the cpu to SVC32 mode, 54 * except if in HYP mode already 55 */ 56 mrs r0, cpsr 57 and r1, r0, #0x1f @ mask mode bits 58 teq r1, #0x1a @ test for HYP mode 59 bicne r0, r0, #0x1f @ clear all mode bits 60 orrne r0, r0, #0x13 @ set SVC mode 61 orr r0, r0, #0xc0 @ disable FIQ and IRQ 62 msr cpsr,r0 63 64/* 65 * Setup vector: 66 * (OMAP4 spl TEXT_BASE is not 32 byte aligned. 67 * Continue to use ROM code vector only in OMAP4 spl) 68 */ 69#if !(defined(CONFIG_OMAP44XX) && defined(CONFIG_SPL_BUILD)) 70 /* Set V=0 in CP15 SCTLR register - for VBAR to point to vector */ 71 mrc p15, 0, r0, c1, c0, 0 @ Read CP15 SCTLR Register 72 bic r0, #CR_V @ V = 0 73 mcr p15, 0, r0, c1, c0, 0 @ Write CP15 SCTLR Register 74 75#ifdef CONFIG_HAS_VBAR 76 /* Set vector address in CP15 VBAR register */ 77 ldr r0, =_start 78 mcr p15, 0, r0, c12, c0, 0 @Set VBAR 79#endif 80#endif 81 82 /* the mask ROM code should have PLL and others stable */ 83#ifndef CONFIG_SKIP_LOWLEVEL_INIT 84#ifdef CONFIG_CPU_V7A 85 bl cpu_init_cp15 86#endif 87#ifndef CONFIG_SKIP_LOWLEVEL_INIT_ONLY 88 bl cpu_init_crit 89#endif 90#endif 91 92 bl _main 93 94/*------------------------------------------------------------------------------*/ 95 96ENTRY(c_runtime_cpu_setup) 97/* 98 * If I-cache is enabled invalidate it 99 */ 100#ifndef CONFIG_SYS_ICACHE_OFF 101 mcr p15, 0, r0, c7, c5, 0 @ invalidate icache 102 mcr p15, 0, r0, c7, c10, 4 @ DSB 103 mcr p15, 0, r0, c7, c5, 4 @ ISB 104#endif 105 106 bx lr 107 108ENDPROC(c_runtime_cpu_setup) 109 110/************************************************************************* 111 * 112 * void save_boot_params(u32 r0, u32 r1, u32 r2, u32 r3) 113 * __attribute__((weak)); 114 * 115 * Stack pointer is not yet initialized at this moment 116 * Don't save anything to stack even if compiled with -O0 117 * 118 *************************************************************************/ 119ENTRY(save_boot_params) 120 b save_boot_params_ret @ back to my caller 121ENDPROC(save_boot_params) 122 .weak save_boot_params 123 124#ifdef CONFIG_ARMV7_LPAE 125ENTRY(switch_to_hypervisor) 126 b switch_to_hypervisor_ret 127ENDPROC(switch_to_hypervisor) 128 .weak switch_to_hypervisor 129#endif 130 131/************************************************************************* 132 * 133 * cpu_init_cp15 134 * 135 * Setup CP15 registers (cache, MMU, TLBs). The I-cache is turned on unless 136 * CONFIG_SYS_ICACHE_OFF is defined. 137 * 138 *************************************************************************/ 139ENTRY(cpu_init_cp15) 140 /* 141 * Invalidate L1 I/D 142 */ 143 mov r0, #0 @ set up for MCR 144 mcr p15, 0, r0, c8, c7, 0 @ invalidate TLBs 145 mcr p15, 0, r0, c7, c5, 0 @ invalidate icache 146 mcr p15, 0, r0, c7, c5, 6 @ invalidate BP array 147 mcr p15, 0, r0, c7, c10, 4 @ DSB 148 mcr p15, 0, r0, c7, c5, 4 @ ISB 149 150 /* 151 * disable MMU stuff and caches 152 */ 153 mrc p15, 0, r0, c1, c0, 0 154 bic r0, r0, #0x00002000 @ clear bits 13 (--V-) 155 bic r0, r0, #0x00000007 @ clear bits 2:0 (-CAM) 156 orr r0, r0, #0x00000002 @ set bit 1 (--A-) Align 157 orr r0, r0, #0x00000800 @ set bit 11 (Z---) BTB 158#ifdef CONFIG_SYS_ICACHE_OFF 159 bic r0, r0, #0x00001000 @ clear bit 12 (I) I-cache 160#else 161 orr r0, r0, #0x00001000 @ set bit 12 (I) I-cache 162#endif 163 mcr p15, 0, r0, c1, c0, 0 164 165#ifdef CONFIG_ARM_ERRATA_716044 166 mrc p15, 0, r0, c1, c0, 0 @ read system control register 167 orr r0, r0, #1 << 11 @ set bit #11 168 mcr p15, 0, r0, c1, c0, 0 @ write system control register 169#endif 170 171#if (defined(CONFIG_ARM_ERRATA_742230) || defined(CONFIG_ARM_ERRATA_794072)) 172 mrc p15, 0, r0, c15, c0, 1 @ read diagnostic register 173 orr r0, r0, #1 << 4 @ set bit #4 174 mcr p15, 0, r0, c15, c0, 1 @ write diagnostic register 175#endif 176 177#ifdef CONFIG_ARM_ERRATA_743622 178 mrc p15, 0, r0, c15, c0, 1 @ read diagnostic register 179 orr r0, r0, #1 << 6 @ set bit #6 180 mcr p15, 0, r0, c15, c0, 1 @ write diagnostic register 181#endif 182 183#ifdef CONFIG_ARM_ERRATA_751472 184 mrc p15, 0, r0, c15, c0, 1 @ read diagnostic register 185 orr r0, r0, #1 << 11 @ set bit #11 186 mcr p15, 0, r0, c15, c0, 1 @ write diagnostic register 187#endif 188#ifdef CONFIG_ARM_ERRATA_761320 189 mrc p15, 0, r0, c15, c0, 1 @ read diagnostic register 190 orr r0, r0, #1 << 21 @ set bit #21 191 mcr p15, 0, r0, c15, c0, 1 @ write diagnostic register 192#endif 193 194#ifdef CONFIG_ARM_ERRATA_845369 195 mrc p15, 0, r0, c15, c0, 1 @ read diagnostic register 196 orr r0, r0, #1 << 22 @ set bit #22 197 mcr p15, 0, r0, c15, c0, 1 @ write diagnostic register 198#endif 199 200 mov r5, lr @ Store my Caller 201 mrc p15, 0, r1, c0, c0, 0 @ r1 has Read Main ID Register (MIDR) 202 mov r3, r1, lsr #20 @ get variant field 203 and r3, r3, #0xf @ r3 has CPU variant 204 and r4, r1, #0xf @ r4 has CPU revision 205 mov r2, r3, lsl #4 @ shift variant field for combined value 206 orr r2, r4, r2 @ r2 has combined CPU variant + revision 207 208#ifdef CONFIG_ARM_ERRATA_798870 209 cmp r2, #0x30 @ Applies to lower than R3p0 210 bge skip_errata_798870 @ skip if not affected rev 211 cmp r2, #0x20 @ Applies to including and above R2p0 212 blt skip_errata_798870 @ skip if not affected rev 213 214 mrc p15, 1, r0, c15, c0, 0 @ read l2 aux ctrl reg 215 orr r0, r0, #1 << 7 @ Enable hazard-detect timeout 216 push {r1-r5} @ Save the cpu info registers 217 bl v7_arch_cp15_set_l2aux_ctrl 218 isb @ Recommended ISB after l2actlr update 219 pop {r1-r5} @ Restore the cpu info - fall through 220skip_errata_798870: 221#endif 222 223#ifdef CONFIG_ARM_ERRATA_801819 224 cmp r2, #0x24 @ Applies to lt including R2p4 225 bgt skip_errata_801819 @ skip if not affected rev 226 cmp r2, #0x20 @ Applies to including and above R2p0 227 blt skip_errata_801819 @ skip if not affected rev 228 mrc p15, 0, r0, c0, c0, 6 @ pick up REVIDR reg 229 and r0, r0, #1 << 3 @ check REVIDR[3] 230 cmp r0, #1 << 3 231 beq skip_errata_801819 @ skip erratum if REVIDR[3] is set 232 233 mrc p15, 0, r0, c1, c0, 1 @ read auxilary control register 234 orr r0, r0, #3 << 27 @ Disables streaming. All write-allocate 235 @ lines allocate in the L1 or L2 cache. 236 orr r0, r0, #3 << 25 @ Disables streaming. All write-allocate 237 @ lines allocate in the L1 cache. 238 push {r1-r5} @ Save the cpu info registers 239 bl v7_arch_cp15_set_acr 240 pop {r1-r5} @ Restore the cpu info - fall through 241skip_errata_801819: 242#endif 243 244#ifdef CONFIG_ARM_CORTEX_A15_CVE_2017_5715 245 mrc p15, 0, r0, c1, c0, 1 @ read auxilary control register 246 orr r0, r0, #1 << 0 @ Enable invalidates of BTB 247 push {r1-r5} @ Save the cpu info registers 248 bl v7_arch_cp15_set_acr 249 pop {r1-r5} @ Restore the cpu info - fall through 250#endif 251 252#ifdef CONFIG_ARM_ERRATA_454179 253 mrc p15, 0, r0, c1, c0, 1 @ Read ACR 254 255 cmp r2, #0x21 @ Only on < r2p1 256 orrlt r0, r0, #(0x3 << 6) @ Set DBSM(BIT7) and IBE(BIT6) bits 257 258 push {r1-r5} @ Save the cpu info registers 259 bl v7_arch_cp15_set_acr 260 pop {r1-r5} @ Restore the cpu info - fall through 261#endif 262 263#if defined(CONFIG_ARM_ERRATA_430973) || defined (CONFIG_ARM_CORTEX_A8_CVE_2017_5715) 264 mrc p15, 0, r0, c1, c0, 1 @ Read ACR 265 266#ifdef CONFIG_ARM_CORTEX_A8_CVE_2017_5715 267 orr r0, r0, #(0x1 << 6) @ Set IBE bit always to enable OS WA 268#else 269 cmp r2, #0x21 @ Only on < r2p1 270 orrlt r0, r0, #(0x1 << 6) @ Set IBE bit 271#endif 272 push {r1-r5} @ Save the cpu info registers 273 bl v7_arch_cp15_set_acr 274 pop {r1-r5} @ Restore the cpu info - fall through 275#endif 276 277#ifdef CONFIG_ARM_ERRATA_621766 278 mrc p15, 0, r0, c1, c0, 1 @ Read ACR 279 280 cmp r2, #0x21 @ Only on < r2p1 281 orrlt r0, r0, #(0x1 << 5) @ Set L1NEON bit 282 283 push {r1-r5} @ Save the cpu info registers 284 bl v7_arch_cp15_set_acr 285 pop {r1-r5} @ Restore the cpu info - fall through 286#endif 287 288#ifdef CONFIG_ARM_ERRATA_725233 289 mrc p15, 1, r0, c9, c0, 2 @ Read L2ACR 290 291 cmp r2, #0x21 @ Only on < r2p1 (Cortex A8) 292 orrlt r0, r0, #(0x1 << 27) @ L2 PLD data forwarding disable 293 294 push {r1-r5} @ Save the cpu info registers 295 bl v7_arch_cp15_set_l2aux_ctrl 296 pop {r1-r5} @ Restore the cpu info - fall through 297#endif 298 299#ifdef CONFIG_ARM_ERRATA_852421 300 mrc p15, 0, r0, c15, c0, 1 @ read diagnostic register 301 orr r0, r0, #1 << 24 @ set bit #24 302 mcr p15, 0, r0, c15, c0, 1 @ write diagnostic register 303#endif 304 305#ifdef CONFIG_ARM_ERRATA_852423 306 mrc p15, 0, r0, c15, c0, 1 @ read diagnostic register 307 orr r0, r0, #1 << 12 @ set bit #12 308 mcr p15, 0, r0, c15, c0, 1 @ write diagnostic register 309#endif 310 311 mov pc, r5 @ back to my caller 312ENDPROC(cpu_init_cp15) 313 314#if !defined(CONFIG_SKIP_LOWLEVEL_INIT) && \ 315 !defined(CONFIG_SKIP_LOWLEVEL_INIT_ONLY) 316/************************************************************************* 317 * 318 * CPU_init_critical registers 319 * 320 * setup important registers 321 * setup memory timing 322 * 323 *************************************************************************/ 324ENTRY(cpu_init_crit) 325 /* 326 * Jump to board specific initialization... 327 * The Mask ROM will have already initialized 328 * basic memory. Go here to bump up clock rate and handle 329 * wake up conditions. 330 */ 331 b lowlevel_init @ go setup pll,mux,memory 332ENDPROC(cpu_init_crit) 333#endif 334