1/* 2 * code for switching cores into non-secure state and into HYP mode 3 * 4 * Copyright (c) 2013 Andre Przywara <andre.przywara@linaro.org> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9#include <config.h> 10#include <linux/linkage.h> 11#include <asm/gic.h> 12#include <asm/armv7.h> 13#include <asm/proc-armv/ptrace.h> 14 15.arch_extension sec 16.arch_extension virt 17 18 .pushsection ._secure.text, "ax" 19 20 .align 5 21/* the vector table for secure state and HYP mode */ 22_monitor_vectors: 23 .word 0 /* reset */ 24 .word 0 /* undef */ 25 adr pc, _secure_monitor 26 .word 0 27 .word 0 28 .word 0 29 .word 0 30 .word 0 31 32.macro is_cpu_virt_capable tmp 33 mrc p15, 0, \tmp, c0, c1, 1 @ read ID_PFR1 34 and \tmp, \tmp, #CPUID_ARM_VIRT_MASK @ mask virtualization bits 35 cmp \tmp, #(1 << CPUID_ARM_VIRT_SHIFT) 36.endm 37 38/* 39 * secure monitor handler 40 * U-Boot calls this "software interrupt" in start.S 41 * This is executed on a "smc" instruction, we use a "smc #0" to switch 42 * to non-secure state. 43 * r0, r1, r2: passed to the callee 44 * ip: target PC 45 */ 46_secure_monitor: 47#ifdef CONFIG_ARMV7_PSCI 48 ldr r5, =_psci_vectors @ Switch to the next monitor 49 mcr p15, 0, r5, c12, c0, 1 50 isb 51 52 @ Obtain a secure stack 53 bl psci_stack_setup 54 55 @ Configure the PSCI backend 56 push {r0, r1, r2, ip} 57 bl psci_arch_init 58 pop {r0, r1, r2, ip} 59#endif 60 61#ifdef CONFIG_ARM_ERRATA_773022 62 mrc p15, 0, r5, c1, c0, 1 63 orr r5, r5, #(1 << 1) 64 mcr p15, 0, r5, c1, c0, 1 65 isb 66#endif 67 68#ifdef CONFIG_ARM_ERRATA_774769 69 mrc p15, 0, r5, c1, c0, 1 70 orr r5, r5, #(1 << 25) 71 mcr p15, 0, r5, c1, c0, 1 72 isb 73#endif 74 75 mrc p15, 0, r5, c1, c1, 0 @ read SCR 76 bic r5, r5, #0x4a @ clear IRQ, EA, nET bits 77 orr r5, r5, #0x31 @ enable NS, AW, FW bits 78 @ FIQ preserved for secure mode 79 mov r6, #SVC_MODE @ default mode is SVC 80 is_cpu_virt_capable r4 81#ifdef CONFIG_ARMV7_VIRT 82 orreq r5, r5, #0x100 @ allow HVC instruction 83 moveq r6, #HYP_MODE @ Enter the kernel as HYP 84#endif 85 86 mcr p15, 0, r5, c1, c1, 0 @ write SCR (with NS bit set) 87 isb 88 89 bne 1f 90 91 @ Reset CNTVOFF to 0 before leaving monitor mode 92 mrc p15, 0, r4, c0, c1, 1 @ read ID_PFR1 93 ands r4, r4, #CPUID_ARM_GENTIMER_MASK @ test arch timer bits 94 movne r4, #0 95 mcrrne p15, 4, r4, r4, c14 @ Reset CNTVOFF to zero 961: 97 mov lr, ip 98 mov ip, #(F_BIT | I_BIT | A_BIT) @ Set A, I and F 99 tst lr, #1 @ Check for Thumb PC 100 orrne ip, ip, #T_BIT @ Set T if Thumb 101 orr ip, ip, r6 @ Slot target mode in 102 msr spsr_cxfs, ip @ Set full SPSR 103 movs pc, lr @ ERET to non-secure 104 105ENTRY(_do_nonsec_entry) 106 mov ip, r0 107 mov r0, r1 108 mov r1, r2 109 mov r2, r3 110 smc #0 111ENDPROC(_do_nonsec_entry) 112 113.macro get_cbar_addr addr 114#ifdef CONFIG_ARM_GIC_BASE_ADDRESS 115 ldr \addr, =CONFIG_ARM_GIC_BASE_ADDRESS 116#else 117 mrc p15, 4, \addr, c15, c0, 0 @ read CBAR 118 bfc \addr, #0, #15 @ clear reserved bits 119#endif 120.endm 121 122.macro get_gicd_addr addr 123 get_cbar_addr \addr 124 add \addr, \addr, #GIC_DIST_OFFSET @ GIC dist i/f offset 125.endm 126 127.macro get_gicc_addr addr, tmp 128 get_cbar_addr \addr 129 is_cpu_virt_capable \tmp 130 movne \tmp, #GIC_CPU_OFFSET_A9 @ GIC CPU offset for A9 131 moveq \tmp, #GIC_CPU_OFFSET_A15 @ GIC CPU offset for A15/A7 132 add \addr, \addr, \tmp 133.endm 134 135#ifndef CONFIG_ARMV7_PSCI 136/* 137 * Secondary CPUs start here and call the code for the core specific parts 138 * of the non-secure and HYP mode transition. The GIC distributor specific 139 * code has already been executed by a C function before. 140 * Then they go back to wfi and wait to be woken up by the kernel again. 141 */ 142ENTRY(_smp_pen) 143 cpsid i 144 cpsid f 145 146 bl _nonsec_init 147 148 adr r0, _smp_pen @ do not use this address again 149 b smp_waitloop @ wait for IPIs, board specific 150ENDPROC(_smp_pen) 151#endif 152 153/* 154 * Switch a core to non-secure state. 155 * 156 * 1. initialize the GIC per-core interface 157 * 2. allow coprocessor access in non-secure modes 158 * 159 * Called from smp_pen by secondary cores and directly by the BSP. 160 * Do not assume that the stack is available and only use registers 161 * r0-r3 and r12. 162 * 163 * PERIPHBASE is used to get the GIC address. This could be 40 bits long, 164 * though, but we check this in C before calling this function. 165 */ 166ENTRY(_nonsec_init) 167 get_gicd_addr r3 168 169 mvn r1, #0 @ all bits to 1 170 str r1, [r3, #GICD_IGROUPRn] @ allow private interrupts 171 172 get_gicc_addr r3, r1 173 174 mov r1, #3 @ Enable both groups 175 str r1, [r3, #GICC_CTLR] @ and clear all other bits 176 mov r1, #0xff 177 str r1, [r3, #GICC_PMR] @ set priority mask register 178 179 mrc p15, 0, r0, c1, c1, 2 180 movw r1, #0x3fff 181 movt r1, #0x0004 182 orr r0, r0, r1 183 mcr p15, 0, r0, c1, c1, 2 @ NSACR = all copros to non-sec 184 185/* The CNTFRQ register of the generic timer needs to be 186 * programmed in secure state. Some primary bootloaders / firmware 187 * omit this, so if the frequency is provided in the configuration, 188 * we do this here instead. 189 * But first check if we have the generic timer. 190 */ 191#ifdef COUNTER_FREQUENCY 192 mrc p15, 0, r0, c0, c1, 1 @ read ID_PFR1 193 and r0, r0, #CPUID_ARM_GENTIMER_MASK @ mask arch timer bits 194 cmp r0, #(1 << CPUID_ARM_GENTIMER_SHIFT) 195 ldreq r1, =COUNTER_FREQUENCY 196 mcreq p15, 0, r1, c14, c0, 0 @ write CNTFRQ 197#endif 198 199 adr r1, _monitor_vectors 200 mcr p15, 0, r1, c12, c0, 1 @ set MVBAR to secure vectors 201 isb 202 203 mov r0, r3 @ return GICC address 204 bx lr 205ENDPROC(_nonsec_init) 206 207#ifdef CONFIG_SMP_PEN_ADDR 208/* void __weak smp_waitloop(unsigned previous_address); */ 209ENTRY(smp_waitloop) 210 wfi 211 ldr r1, =CONFIG_SMP_PEN_ADDR @ load start address 212 ldr r1, [r1] 213#ifdef CONFIG_PEN_ADDR_BIG_ENDIAN 214 rev r1, r1 215#endif 216 cmp r0, r1 @ make sure we dont execute this code 217 beq smp_waitloop @ again (due to a spurious wakeup) 218 mov r0, r1 219 b _do_nonsec_entry 220ENDPROC(smp_waitloop) 221.weak smp_waitloop 222#endif 223 224 .popsection 225