1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Freescale i.MX28 Boot PMIC init 4 * 5 * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com> 6 * on behalf of DENX Software Engineering GmbH 7 */ 8 9 #include <common.h> 10 #include <config.h> 11 #include <asm/io.h> 12 #include <asm/arch/imx-regs.h> 13 14 #include "mxs_init.h" 15 16 #ifdef CONFIG_SYS_MXS_VDD5V_ONLY 17 #define DCDC4P2_DROPOUT_CONFIG POWER_DCDC4P2_DROPOUT_CTRL_100MV | \ 18 POWER_DCDC4P2_DROPOUT_CTRL_SRC_4P2 19 #else 20 #define DCDC4P2_DROPOUT_CONFIG POWER_DCDC4P2_DROPOUT_CTRL_100MV | \ 21 POWER_DCDC4P2_DROPOUT_CTRL_SRC_SEL 22 #endif 23 /** 24 * mxs_power_clock2xtal() - Switch CPU core clock source to 24MHz XTAL 25 * 26 * This function switches the CPU core clock from PLL to 24MHz XTAL 27 * oscilator. This is necessary if the PLL is being reconfigured to 28 * prevent crash of the CPU core. 29 */ 30 static void mxs_power_clock2xtal(void) 31 { 32 struct mxs_clkctrl_regs *clkctrl_regs = 33 (struct mxs_clkctrl_regs *)MXS_CLKCTRL_BASE; 34 35 debug("SPL: Switching CPU clock to 24MHz XTAL\n"); 36 37 /* Set XTAL as CPU reference clock */ 38 writel(CLKCTRL_CLKSEQ_BYPASS_CPU, 39 &clkctrl_regs->hw_clkctrl_clkseq_set); 40 } 41 42 /** 43 * mxs_power_clock2pll() - Switch CPU core clock source to PLL 44 * 45 * This function switches the CPU core clock from 24MHz XTAL oscilator 46 * to PLL. This can only be called once the PLL has re-locked and once 47 * the PLL is stable after reconfiguration. 48 */ 49 static void mxs_power_clock2pll(void) 50 { 51 struct mxs_clkctrl_regs *clkctrl_regs = 52 (struct mxs_clkctrl_regs *)MXS_CLKCTRL_BASE; 53 54 debug("SPL: Switching CPU core clock source to PLL\n"); 55 56 /* 57 * TODO: Are we really? It looks like we turn on PLL0, but we then 58 * set the CLKCTRL_CLKSEQ_BYPASS_CPU bit of the (which was already 59 * set by mxs_power_clock2xtal()). Clearing this bit here seems to 60 * introduce some instability (causing the CPU core to hang). Maybe 61 * we aren't giving PLL0 enough time to stabilise? 62 */ 63 setbits_le32(&clkctrl_regs->hw_clkctrl_pll0ctrl0, 64 CLKCTRL_PLL0CTRL0_POWER); 65 early_delay(100); 66 67 /* 68 * TODO: Should the PLL0 FORCE_LOCK bit be set here followed be a 69 * wait on the PLL0 LOCK bit? 70 */ 71 setbits_le32(&clkctrl_regs->hw_clkctrl_clkseq, 72 CLKCTRL_CLKSEQ_BYPASS_CPU); 73 } 74 75 /** 76 * mxs_power_set_auto_restart() - Set the auto-restart bit 77 * 78 * This function ungates the RTC block and sets the AUTO_RESTART 79 * bit to work around a design bug on MX28EVK Rev. A . 80 */ 81 82 static void mxs_power_set_auto_restart(void) 83 { 84 struct mxs_rtc_regs *rtc_regs = 85 (struct mxs_rtc_regs *)MXS_RTC_BASE; 86 87 debug("SPL: Setting auto-restart bit\n"); 88 89 writel(RTC_CTRL_SFTRST, &rtc_regs->hw_rtc_ctrl_clr); 90 while (readl(&rtc_regs->hw_rtc_ctrl) & RTC_CTRL_SFTRST) 91 ; 92 93 writel(RTC_CTRL_CLKGATE, &rtc_regs->hw_rtc_ctrl_clr); 94 while (readl(&rtc_regs->hw_rtc_ctrl) & RTC_CTRL_CLKGATE) 95 ; 96 97 /* Do nothing if flag already set */ 98 if (readl(&rtc_regs->hw_rtc_persistent0) & RTC_PERSISTENT0_AUTO_RESTART) 99 return; 100 101 while (readl(&rtc_regs->hw_rtc_stat) & RTC_STAT_NEW_REGS_MASK) 102 ; 103 104 setbits_le32(&rtc_regs->hw_rtc_persistent0, 105 RTC_PERSISTENT0_AUTO_RESTART); 106 writel(RTC_CTRL_FORCE_UPDATE, &rtc_regs->hw_rtc_ctrl_set); 107 writel(RTC_CTRL_FORCE_UPDATE, &rtc_regs->hw_rtc_ctrl_clr); 108 while (readl(&rtc_regs->hw_rtc_stat) & RTC_STAT_NEW_REGS_MASK) 109 ; 110 while (readl(&rtc_regs->hw_rtc_stat) & RTC_STAT_STALE_REGS_MASK) 111 ; 112 } 113 114 /** 115 * mxs_power_set_linreg() - Set linear regulators 25mV below DC-DC converter 116 * 117 * This function configures the VDDIO, VDDA and VDDD linear regulators output 118 * to be 25mV below the VDDIO, VDDA and VDDD output from the DC-DC switching 119 * converter. This is the recommended setting for the case where we use both 120 * linear regulators and DC-DC converter to power the VDDIO rail. 121 */ 122 static void mxs_power_set_linreg(void) 123 { 124 struct mxs_power_regs *power_regs = 125 (struct mxs_power_regs *)MXS_POWER_BASE; 126 127 /* Set linear regulator 25mV below switching converter */ 128 debug("SPL: Setting VDDD 25mV below DC-DC converters\n"); 129 clrsetbits_le32(&power_regs->hw_power_vdddctrl, 130 POWER_VDDDCTRL_LINREG_OFFSET_MASK, 131 POWER_VDDDCTRL_LINREG_OFFSET_1STEPS_BELOW); 132 133 debug("SPL: Setting VDDA 25mV below DC-DC converters\n"); 134 clrsetbits_le32(&power_regs->hw_power_vddactrl, 135 POWER_VDDACTRL_LINREG_OFFSET_MASK, 136 POWER_VDDACTRL_LINREG_OFFSET_1STEPS_BELOW); 137 138 debug("SPL: Setting VDDIO 25mV below DC-DC converters\n"); 139 clrsetbits_le32(&power_regs->hw_power_vddioctrl, 140 POWER_VDDIOCTRL_LINREG_OFFSET_MASK, 141 POWER_VDDIOCTRL_LINREG_OFFSET_1STEPS_BELOW); 142 } 143 144 /** 145 * mxs_get_batt_volt() - Measure battery input voltage 146 * 147 * This function retrieves the battery input voltage and returns it. 148 */ 149 static int mxs_get_batt_volt(void) 150 { 151 struct mxs_power_regs *power_regs = 152 (struct mxs_power_regs *)MXS_POWER_BASE; 153 uint32_t volt = readl(&power_regs->hw_power_battmonitor); 154 volt &= POWER_BATTMONITOR_BATT_VAL_MASK; 155 volt >>= POWER_BATTMONITOR_BATT_VAL_OFFSET; 156 volt *= 8; 157 158 debug("SPL: Battery Voltage = %dmV\n", volt); 159 return volt; 160 } 161 162 /** 163 * mxs_is_batt_ready() - Test if the battery provides enough voltage to boot 164 * 165 * This function checks if the battery input voltage is higher than 3.6V and 166 * therefore allows the system to successfully boot using this power source. 167 */ 168 static int mxs_is_batt_ready(void) 169 { 170 return (mxs_get_batt_volt() >= 3600); 171 } 172 173 /** 174 * mxs_is_batt_good() - Test if battery is operational at all 175 * 176 * This function starts recharging the battery and tests if the input current 177 * provided by the 5V input recharging the battery is also sufficient to power 178 * the DC-DC converter. 179 */ 180 static int mxs_is_batt_good(void) 181 { 182 struct mxs_power_regs *power_regs = 183 (struct mxs_power_regs *)MXS_POWER_BASE; 184 uint32_t volt = mxs_get_batt_volt(); 185 186 if ((volt >= 2400) && (volt <= 4300)) { 187 debug("SPL: Battery is good\n"); 188 return 1; 189 } 190 191 clrsetbits_le32(&power_regs->hw_power_5vctrl, 192 POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK, 193 0x3 << POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET); 194 writel(POWER_5VCTRL_PWD_CHARGE_4P2_MASK, 195 &power_regs->hw_power_5vctrl_clr); 196 197 clrsetbits_le32(&power_regs->hw_power_charge, 198 POWER_CHARGE_STOP_ILIMIT_MASK | POWER_CHARGE_BATTCHRG_I_MASK, 199 POWER_CHARGE_STOP_ILIMIT_10MA | 0x3); 200 201 writel(POWER_CHARGE_PWD_BATTCHRG, &power_regs->hw_power_charge_clr); 202 writel(POWER_5VCTRL_PWD_CHARGE_4P2_MASK, 203 &power_regs->hw_power_5vctrl_clr); 204 205 early_delay(500000); 206 207 volt = mxs_get_batt_volt(); 208 209 if (volt >= 3500) { 210 debug("SPL: Battery Voltage too high\n"); 211 return 0; 212 } 213 214 if (volt >= 2400) { 215 debug("SPL: Battery is good\n"); 216 return 1; 217 } 218 219 writel(POWER_CHARGE_STOP_ILIMIT_MASK | POWER_CHARGE_BATTCHRG_I_MASK, 220 &power_regs->hw_power_charge_clr); 221 writel(POWER_CHARGE_PWD_BATTCHRG, &power_regs->hw_power_charge_set); 222 223 debug("SPL: Battery Voltage too low\n"); 224 return 0; 225 } 226 227 /** 228 * mxs_power_setup_5v_detect() - Start the 5V input detection comparator 229 * 230 * This function enables the 5V detection comparator and sets the 5V valid 231 * threshold to 4.4V . We use 4.4V threshold here to make sure that even 232 * under high load, the voltage drop on the 5V input won't be so critical 233 * to cause undervolt on the 4P2 linear regulator supplying the DC-DC 234 * converter and thus making the system crash. 235 */ 236 static void mxs_power_setup_5v_detect(void) 237 { 238 struct mxs_power_regs *power_regs = 239 (struct mxs_power_regs *)MXS_POWER_BASE; 240 241 /* Start 5V detection */ 242 debug("SPL: Starting 5V input detection comparator\n"); 243 clrsetbits_le32(&power_regs->hw_power_5vctrl, 244 POWER_5VCTRL_VBUSVALID_TRSH_MASK, 245 POWER_5VCTRL_VBUSVALID_TRSH_4V4 | 246 POWER_5VCTRL_PWRUP_VBUS_CMPS); 247 } 248 249 /** 250 * mxs_power_switch_dcdc_clocksource() - Switch PLL clock for DC-DC converters 251 * @freqsel: One of the POWER_MISC_FREQSEL_xxx defines to select the clock 252 * 253 * This function configures and then enables an alternative PLL clock source 254 * for the DC-DC converters. 255 */ 256 void mxs_power_switch_dcdc_clocksource(uint32_t freqsel) 257 { 258 struct mxs_power_regs *power_regs = 259 (struct mxs_power_regs *)MXS_POWER_BASE; 260 261 /* Select clocksource for DC-DC converters */ 262 clrsetbits_le32(&power_regs->hw_power_misc, 263 POWER_MISC_FREQSEL_MASK, 264 freqsel); 265 setbits_le32(&power_regs->hw_power_misc, 266 POWER_MISC_SEL_PLLCLK); 267 } 268 269 /** 270 * mxs_power_setup_dcdc_clocksource() - Setup PLL clock source for DC-DC converters 271 * 272 * Normally, there is no need to switch DC-DC clocksource. This is the reason, 273 * why this function is a stub and does nothing. However, boards can implement 274 * this function when required and call mxs_power_switch_dcdc_clocksource() to 275 * switch to an alternative clock source. 276 */ 277 __weak void mxs_power_setup_dcdc_clocksource(void) 278 { 279 debug("SPL: Using default DC-DC clocksource\n"); 280 } 281 282 /** 283 * mxs_src_power_init() - Preconfigure the power block 284 * 285 * This function configures reasonable values for the DC-DC control loop 286 * and battery monitor. 287 */ 288 static void mxs_src_power_init(void) 289 { 290 struct mxs_power_regs *power_regs = 291 (struct mxs_power_regs *)MXS_POWER_BASE; 292 293 debug("SPL: Pre-Configuring power block\n"); 294 295 /* Improve efficieny and reduce transient ripple */ 296 writel(POWER_LOOPCTRL_TOGGLE_DIF | POWER_LOOPCTRL_EN_CM_HYST | 297 POWER_LOOPCTRL_EN_DF_HYST, &power_regs->hw_power_loopctrl_set); 298 299 clrsetbits_le32(&power_regs->hw_power_dclimits, 300 POWER_DCLIMITS_POSLIMIT_BUCK_MASK, 301 0x30 << POWER_DCLIMITS_POSLIMIT_BUCK_OFFSET); 302 303 setbits_le32(&power_regs->hw_power_battmonitor, 304 POWER_BATTMONITOR_EN_BATADJ); 305 306 /* Increase the RCSCALE level for quick DCDC response to dynamic load */ 307 clrsetbits_le32(&power_regs->hw_power_loopctrl, 308 POWER_LOOPCTRL_EN_RCSCALE_MASK, 309 POWER_LOOPCTRL_RCSCALE_THRESH | 310 POWER_LOOPCTRL_EN_RCSCALE_8X); 311 312 clrsetbits_le32(&power_regs->hw_power_minpwr, 313 POWER_MINPWR_HALFFETS, POWER_MINPWR_DOUBLE_FETS); 314 315 /* 5V to battery handoff ... FIXME */ 316 setbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_DCDC_XFER); 317 early_delay(30); 318 clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_DCDC_XFER); 319 } 320 321 /** 322 * mxs_power_init_4p2_params() - Configure the parameters of the 4P2 regulator 323 * 324 * This function configures the necessary parameters for the 4P2 linear 325 * regulator to supply the DC-DC converter from 5V input. 326 */ 327 static void mxs_power_init_4p2_params(void) 328 { 329 struct mxs_power_regs *power_regs = 330 (struct mxs_power_regs *)MXS_POWER_BASE; 331 332 debug("SPL: Configuring common 4P2 regulator params\n"); 333 334 /* Setup 4P2 parameters */ 335 clrsetbits_le32(&power_regs->hw_power_dcdc4p2, 336 POWER_DCDC4P2_CMPTRIP_MASK | POWER_DCDC4P2_TRG_MASK, 337 POWER_DCDC4P2_TRG_4V2 | (31 << POWER_DCDC4P2_CMPTRIP_OFFSET)); 338 339 clrsetbits_le32(&power_regs->hw_power_5vctrl, 340 POWER_5VCTRL_HEADROOM_ADJ_MASK, 341 0x4 << POWER_5VCTRL_HEADROOM_ADJ_OFFSET); 342 343 clrsetbits_le32(&power_regs->hw_power_dcdc4p2, 344 POWER_DCDC4P2_DROPOUT_CTRL_MASK, 345 DCDC4P2_DROPOUT_CONFIG); 346 347 clrsetbits_le32(&power_regs->hw_power_5vctrl, 348 POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK, 349 0x3f << POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET); 350 } 351 352 /** 353 * mxs_enable_4p2_dcdc_input() - Enable or disable the DCDC input from 4P2 354 * @xfer: Select if the input shall be enabled or disabled 355 * 356 * This function enables or disables the 4P2 input into the DC-DC converter. 357 */ 358 static void mxs_enable_4p2_dcdc_input(int xfer) 359 { 360 struct mxs_power_regs *power_regs = 361 (struct mxs_power_regs *)MXS_POWER_BASE; 362 uint32_t tmp, vbus_thresh, vbus_5vdetect, pwd_bo; 363 uint32_t prev_5v_brnout, prev_5v_droop; 364 365 debug("SPL: %s 4P2 DC-DC Input\n", xfer ? "Enabling" : "Disabling"); 366 367 if (xfer && (readl(&power_regs->hw_power_5vctrl) & 368 POWER_5VCTRL_ENABLE_DCDC)) { 369 return; 370 } 371 372 prev_5v_brnout = readl(&power_regs->hw_power_5vctrl) & 373 POWER_5VCTRL_PWDN_5VBRNOUT; 374 prev_5v_droop = readl(&power_regs->hw_power_ctrl) & 375 POWER_CTRL_ENIRQ_VDD5V_DROOP; 376 377 clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_PWDN_5VBRNOUT); 378 writel(POWER_RESET_UNLOCK_KEY | POWER_RESET_PWD_OFF, 379 &power_regs->hw_power_reset); 380 381 clrbits_le32(&power_regs->hw_power_ctrl, POWER_CTRL_ENIRQ_VDD5V_DROOP); 382 383 /* 384 * Recording orignal values that will be modified temporarlily 385 * to handle a chip bug. See chip errata for CQ ENGR00115837 386 */ 387 tmp = readl(&power_regs->hw_power_5vctrl); 388 vbus_thresh = tmp & POWER_5VCTRL_VBUSVALID_TRSH_MASK; 389 vbus_5vdetect = tmp & POWER_5VCTRL_VBUSVALID_5VDETECT; 390 391 pwd_bo = readl(&power_regs->hw_power_minpwr) & POWER_MINPWR_PWD_BO; 392 393 /* 394 * Disable mechanisms that get erroneously tripped by when setting 395 * the DCDC4P2 EN_DCDC 396 */ 397 clrbits_le32(&power_regs->hw_power_5vctrl, 398 POWER_5VCTRL_VBUSVALID_5VDETECT | 399 POWER_5VCTRL_VBUSVALID_TRSH_MASK); 400 401 writel(POWER_MINPWR_PWD_BO, &power_regs->hw_power_minpwr_set); 402 403 if (xfer) { 404 setbits_le32(&power_regs->hw_power_5vctrl, 405 POWER_5VCTRL_DCDC_XFER); 406 early_delay(20); 407 clrbits_le32(&power_regs->hw_power_5vctrl, 408 POWER_5VCTRL_DCDC_XFER); 409 410 setbits_le32(&power_regs->hw_power_5vctrl, 411 POWER_5VCTRL_ENABLE_DCDC); 412 } else { 413 setbits_le32(&power_regs->hw_power_dcdc4p2, 414 POWER_DCDC4P2_ENABLE_DCDC); 415 } 416 417 early_delay(25); 418 419 clrsetbits_le32(&power_regs->hw_power_5vctrl, 420 POWER_5VCTRL_VBUSVALID_TRSH_MASK, vbus_thresh); 421 422 if (vbus_5vdetect) 423 writel(vbus_5vdetect, &power_regs->hw_power_5vctrl_set); 424 425 if (!pwd_bo) 426 clrbits_le32(&power_regs->hw_power_minpwr, POWER_MINPWR_PWD_BO); 427 428 while (readl(&power_regs->hw_power_ctrl) & POWER_CTRL_VBUS_VALID_IRQ) 429 writel(POWER_CTRL_VBUS_VALID_IRQ, 430 &power_regs->hw_power_ctrl_clr); 431 432 if (prev_5v_brnout) { 433 writel(POWER_5VCTRL_PWDN_5VBRNOUT, 434 &power_regs->hw_power_5vctrl_set); 435 writel(POWER_RESET_UNLOCK_KEY, 436 &power_regs->hw_power_reset); 437 } else { 438 writel(POWER_5VCTRL_PWDN_5VBRNOUT, 439 &power_regs->hw_power_5vctrl_clr); 440 writel(POWER_RESET_UNLOCK_KEY | POWER_RESET_PWD_OFF, 441 &power_regs->hw_power_reset); 442 } 443 444 while (readl(&power_regs->hw_power_ctrl) & POWER_CTRL_VDD5V_DROOP_IRQ) 445 writel(POWER_CTRL_VDD5V_DROOP_IRQ, 446 &power_regs->hw_power_ctrl_clr); 447 448 if (prev_5v_droop) 449 clrbits_le32(&power_regs->hw_power_ctrl, 450 POWER_CTRL_ENIRQ_VDD5V_DROOP); 451 else 452 setbits_le32(&power_regs->hw_power_ctrl, 453 POWER_CTRL_ENIRQ_VDD5V_DROOP); 454 } 455 456 /** 457 * mxs_power_init_4p2_regulator() - Start the 4P2 regulator 458 * 459 * This function enables the 4P2 regulator and switches the DC-DC converter 460 * to use the 4P2 input. 461 */ 462 static void mxs_power_init_4p2_regulator(void) 463 { 464 struct mxs_power_regs *power_regs = 465 (struct mxs_power_regs *)MXS_POWER_BASE; 466 uint32_t tmp, tmp2; 467 468 debug("SPL: Enabling 4P2 regulator\n"); 469 470 setbits_le32(&power_regs->hw_power_dcdc4p2, POWER_DCDC4P2_ENABLE_4P2); 471 472 writel(POWER_CHARGE_ENABLE_LOAD, &power_regs->hw_power_charge_set); 473 474 writel(POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK, 475 &power_regs->hw_power_5vctrl_clr); 476 clrbits_le32(&power_regs->hw_power_dcdc4p2, POWER_DCDC4P2_TRG_MASK); 477 478 /* Power up the 4p2 rail and logic/control */ 479 writel(POWER_5VCTRL_PWD_CHARGE_4P2_MASK, 480 &power_regs->hw_power_5vctrl_clr); 481 482 /* 483 * Start charging up the 4p2 capacitor. We ramp of this charge 484 * gradually to avoid large inrush current from the 5V cable which can 485 * cause transients/problems 486 */ 487 debug("SPL: Charging 4P2 capacitor\n"); 488 mxs_enable_4p2_dcdc_input(0); 489 490 if (readl(&power_regs->hw_power_ctrl) & POWER_CTRL_VBUS_VALID_IRQ) { 491 /* 492 * If we arrived here, we were unable to recover from mx23 chip 493 * errata 5837. 4P2 is disabled and sufficient battery power is 494 * not present. Exiting to not enable DCDC power during 5V 495 * connected state. 496 */ 497 clrbits_le32(&power_regs->hw_power_dcdc4p2, 498 POWER_DCDC4P2_ENABLE_DCDC); 499 writel(POWER_5VCTRL_PWD_CHARGE_4P2_MASK, 500 &power_regs->hw_power_5vctrl_set); 501 502 debug("SPL: Unable to recover from mx23 errata 5837\n"); 503 hang(); 504 } 505 506 /* 507 * Here we set the 4p2 brownout level to something very close to 4.2V. 508 * We then check the brownout status. If the brownout status is false, 509 * the voltage is already close to the target voltage of 4.2V so we 510 * can go ahead and set the 4P2 current limit to our max target limit. 511 * If the brownout status is true, we need to ramp us the current limit 512 * so that we don't cause large inrush current issues. We step up the 513 * current limit until the brownout status is false or until we've 514 * reached our maximum defined 4p2 current limit. 515 */ 516 debug("SPL: Setting 4P2 brownout level\n"); 517 clrsetbits_le32(&power_regs->hw_power_dcdc4p2, 518 POWER_DCDC4P2_BO_MASK, 519 22 << POWER_DCDC4P2_BO_OFFSET); /* 4.15V */ 520 521 if (!(readl(&power_regs->hw_power_sts) & POWER_STS_DCDC_4P2_BO)) { 522 setbits_le32(&power_regs->hw_power_5vctrl, 523 0x3f << POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET); 524 } else { 525 tmp = (readl(&power_regs->hw_power_5vctrl) & 526 POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK) >> 527 POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET; 528 while (tmp < 0x3f) { 529 if (!(readl(&power_regs->hw_power_sts) & 530 POWER_STS_DCDC_4P2_BO)) { 531 tmp = readl(&power_regs->hw_power_5vctrl); 532 tmp |= POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK; 533 early_delay(100); 534 writel(tmp, &power_regs->hw_power_5vctrl); 535 break; 536 } else { 537 tmp++; 538 tmp2 = readl(&power_regs->hw_power_5vctrl); 539 tmp2 &= ~POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK; 540 tmp2 |= tmp << 541 POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET; 542 writel(tmp2, &power_regs->hw_power_5vctrl); 543 early_delay(100); 544 } 545 } 546 } 547 548 clrbits_le32(&power_regs->hw_power_dcdc4p2, POWER_DCDC4P2_BO_MASK); 549 writel(POWER_CTRL_DCDC4P2_BO_IRQ, &power_regs->hw_power_ctrl_clr); 550 } 551 552 /** 553 * mxs_power_init_dcdc_4p2_source() - Switch DC-DC converter to 4P2 source 554 * 555 * This function configures the DC-DC converter to be supplied from the 4P2 556 * linear regulator. 557 */ 558 static void mxs_power_init_dcdc_4p2_source(void) 559 { 560 struct mxs_power_regs *power_regs = 561 (struct mxs_power_regs *)MXS_POWER_BASE; 562 563 debug("SPL: Switching DC-DC converters to 4P2\n"); 564 565 if (!(readl(&power_regs->hw_power_dcdc4p2) & 566 POWER_DCDC4P2_ENABLE_DCDC)) { 567 debug("SPL: Already switched - aborting\n"); 568 hang(); 569 } 570 571 mxs_enable_4p2_dcdc_input(1); 572 573 if (readl(&power_regs->hw_power_ctrl) & POWER_CTRL_VBUS_VALID_IRQ) { 574 clrbits_le32(&power_regs->hw_power_dcdc4p2, 575 POWER_DCDC4P2_ENABLE_DCDC); 576 writel(POWER_5VCTRL_ENABLE_DCDC, 577 &power_regs->hw_power_5vctrl_clr); 578 writel(POWER_5VCTRL_PWD_CHARGE_4P2_MASK, 579 &power_regs->hw_power_5vctrl_set); 580 } 581 } 582 583 /** 584 * mxs_power_enable_4p2() - Power up the 4P2 regulator 585 * 586 * This function drives the process of powering up the 4P2 linear regulator 587 * and switching the DC-DC converter input over to the 4P2 linear regulator. 588 */ 589 static void mxs_power_enable_4p2(void) 590 { 591 struct mxs_power_regs *power_regs = 592 (struct mxs_power_regs *)MXS_POWER_BASE; 593 uint32_t vdddctrl, vddactrl, vddioctrl; 594 uint32_t tmp; 595 596 debug("SPL: Powering up 4P2 regulator\n"); 597 598 vdddctrl = readl(&power_regs->hw_power_vdddctrl); 599 vddactrl = readl(&power_regs->hw_power_vddactrl); 600 vddioctrl = readl(&power_regs->hw_power_vddioctrl); 601 602 setbits_le32(&power_regs->hw_power_vdddctrl, 603 POWER_VDDDCTRL_DISABLE_FET | POWER_VDDDCTRL_ENABLE_LINREG | 604 POWER_VDDDCTRL_PWDN_BRNOUT); 605 606 setbits_le32(&power_regs->hw_power_vddactrl, 607 POWER_VDDACTRL_DISABLE_FET | POWER_VDDACTRL_ENABLE_LINREG | 608 POWER_VDDACTRL_PWDN_BRNOUT); 609 610 setbits_le32(&power_regs->hw_power_vddioctrl, 611 POWER_VDDIOCTRL_DISABLE_FET | POWER_VDDIOCTRL_PWDN_BRNOUT); 612 613 mxs_power_init_4p2_params(); 614 mxs_power_init_4p2_regulator(); 615 616 /* Shutdown battery (none present) */ 617 if (!mxs_is_batt_ready()) { 618 clrbits_le32(&power_regs->hw_power_dcdc4p2, 619 POWER_DCDC4P2_BO_MASK); 620 writel(POWER_CTRL_DCDC4P2_BO_IRQ, 621 &power_regs->hw_power_ctrl_clr); 622 writel(POWER_CTRL_ENIRQ_DCDC4P2_BO, 623 &power_regs->hw_power_ctrl_clr); 624 } 625 626 mxs_power_init_dcdc_4p2_source(); 627 628 writel(vdddctrl, &power_regs->hw_power_vdddctrl); 629 early_delay(20); 630 writel(vddactrl, &power_regs->hw_power_vddactrl); 631 early_delay(20); 632 writel(vddioctrl, &power_regs->hw_power_vddioctrl); 633 634 /* 635 * Check if FET is enabled on either powerout and if so, 636 * disable load. 637 */ 638 tmp = 0; 639 tmp |= !(readl(&power_regs->hw_power_vdddctrl) & 640 POWER_VDDDCTRL_DISABLE_FET); 641 tmp |= !(readl(&power_regs->hw_power_vddactrl) & 642 POWER_VDDACTRL_DISABLE_FET); 643 tmp |= !(readl(&power_regs->hw_power_vddioctrl) & 644 POWER_VDDIOCTRL_DISABLE_FET); 645 if (tmp) 646 writel(POWER_CHARGE_ENABLE_LOAD, 647 &power_regs->hw_power_charge_clr); 648 649 debug("SPL: 4P2 regulator powered-up\n"); 650 } 651 652 /** 653 * mxs_boot_valid_5v() - Boot from 5V supply 654 * 655 * This function configures the power block to boot from valid 5V input. 656 * This is called only if the 5V is reliable and can properly supply the 657 * CPU. This function proceeds to configure the 4P2 converter to be supplied 658 * from the 5V input. 659 */ 660 static void mxs_boot_valid_5v(void) 661 { 662 struct mxs_power_regs *power_regs = 663 (struct mxs_power_regs *)MXS_POWER_BASE; 664 665 debug("SPL: Booting from 5V supply\n"); 666 667 /* 668 * Use VBUSVALID level instead of VDD5V_GT_VDDIO level to trigger a 5V 669 * disconnect event. FIXME 670 */ 671 writel(POWER_5VCTRL_VBUSVALID_5VDETECT, 672 &power_regs->hw_power_5vctrl_set); 673 674 /* Configure polarity to check for 5V disconnection. */ 675 writel(POWER_CTRL_POLARITY_VBUSVALID | 676 POWER_CTRL_POLARITY_VDD5V_GT_VDDIO, 677 &power_regs->hw_power_ctrl_clr); 678 679 writel(POWER_CTRL_VBUS_VALID_IRQ | POWER_CTRL_VDD5V_GT_VDDIO_IRQ, 680 &power_regs->hw_power_ctrl_clr); 681 682 mxs_power_enable_4p2(); 683 } 684 685 /** 686 * mxs_powerdown() - Shut down the system 687 * 688 * This function powers down the CPU completely. 689 */ 690 static void mxs_powerdown(void) 691 { 692 struct mxs_power_regs *power_regs = 693 (struct mxs_power_regs *)MXS_POWER_BASE; 694 695 debug("Powering Down\n"); 696 697 writel(POWER_RESET_UNLOCK_KEY, &power_regs->hw_power_reset); 698 writel(POWER_RESET_UNLOCK_KEY | POWER_RESET_PWD_OFF, 699 &power_regs->hw_power_reset); 700 } 701 702 /** 703 * mxs_batt_boot() - Configure the power block to boot from battery input 704 * 705 * This function configures the power block to boot from the battery voltage 706 * supply. 707 */ 708 static void mxs_batt_boot(void) 709 { 710 struct mxs_power_regs *power_regs = 711 (struct mxs_power_regs *)MXS_POWER_BASE; 712 713 debug("SPL: Configuring power block to boot from battery\n"); 714 715 clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_PWDN_5VBRNOUT); 716 clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_ENABLE_DCDC); 717 718 clrbits_le32(&power_regs->hw_power_dcdc4p2, 719 POWER_DCDC4P2_ENABLE_DCDC | POWER_DCDC4P2_ENABLE_4P2); 720 writel(POWER_CHARGE_ENABLE_LOAD, &power_regs->hw_power_charge_clr); 721 722 /* 5V to battery handoff. */ 723 setbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_DCDC_XFER); 724 early_delay(30); 725 clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_DCDC_XFER); 726 727 writel(POWER_CTRL_ENIRQ_DCDC4P2_BO, &power_regs->hw_power_ctrl_clr); 728 729 clrsetbits_le32(&power_regs->hw_power_minpwr, 730 POWER_MINPWR_HALFFETS, POWER_MINPWR_DOUBLE_FETS); 731 732 mxs_power_set_linreg(); 733 734 clrbits_le32(&power_regs->hw_power_vdddctrl, 735 POWER_VDDDCTRL_DISABLE_FET | POWER_VDDDCTRL_ENABLE_LINREG); 736 737 clrbits_le32(&power_regs->hw_power_vddactrl, 738 POWER_VDDACTRL_DISABLE_FET | POWER_VDDACTRL_ENABLE_LINREG); 739 740 clrbits_le32(&power_regs->hw_power_vddioctrl, 741 POWER_VDDIOCTRL_DISABLE_FET); 742 743 setbits_le32(&power_regs->hw_power_5vctrl, 744 POWER_5VCTRL_PWD_CHARGE_4P2_MASK); 745 746 setbits_le32(&power_regs->hw_power_5vctrl, 747 POWER_5VCTRL_ENABLE_DCDC); 748 749 clrsetbits_le32(&power_regs->hw_power_5vctrl, 750 POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK, 751 0x8 << POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET); 752 753 mxs_power_enable_4p2(); 754 } 755 756 /** 757 * mxs_handle_5v_conflict() - Test if the 5V input is reliable 758 * 759 * This function tests if the 5V input can reliably supply the system. If it 760 * can, then proceed to configuring the system to boot from 5V source, otherwise 761 * try booting from battery supply. If we can not boot from battery supply 762 * either, shut down the system. 763 */ 764 static void mxs_handle_5v_conflict(void) 765 { 766 struct mxs_power_regs *power_regs = 767 (struct mxs_power_regs *)MXS_POWER_BASE; 768 uint32_t tmp; 769 770 debug("SPL: Resolving 5V conflict\n"); 771 772 setbits_le32(&power_regs->hw_power_vddioctrl, 773 POWER_VDDIOCTRL_BO_OFFSET_MASK); 774 775 for (;;) { 776 tmp = readl(&power_regs->hw_power_sts); 777 778 if (tmp & POWER_STS_VDDIO_BO) { 779 /* 780 * VDDIO has a brownout, then the VDD5V_GT_VDDIO becomes 781 * unreliable 782 */ 783 debug("SPL: VDDIO has a brownout\n"); 784 mxs_powerdown(); 785 break; 786 } 787 788 if (tmp & POWER_STS_VDD5V_GT_VDDIO) { 789 debug("SPL: POWER_STS_VDD5V_GT_VDDIO is set\n"); 790 mxs_boot_valid_5v(); 791 break; 792 } else { 793 debug("SPL: POWER_STS_VDD5V_GT_VDDIO is not set\n"); 794 mxs_powerdown(); 795 break; 796 } 797 798 /* 799 * TODO: I can't see this being reached. We'll either 800 * powerdown or boot from a stable 5V supply. 801 */ 802 if (tmp & POWER_STS_PSWITCH_MASK) { 803 debug("SPL: POWER_STS_PSWITCH_MASK is set\n"); 804 mxs_batt_boot(); 805 break; 806 } 807 } 808 } 809 810 /** 811 * mxs_5v_boot() - Configure the power block to boot from 5V input 812 * 813 * This function handles configuration of the power block when supplied by 814 * a 5V input. 815 */ 816 static void mxs_5v_boot(void) 817 { 818 struct mxs_power_regs *power_regs = 819 (struct mxs_power_regs *)MXS_POWER_BASE; 820 821 debug("SPL: Configuring power block to boot from 5V input\n"); 822 823 /* 824 * NOTE: In original IMX-Bootlets, this also checks for VBUSVALID, 825 * but their implementation always returns 1 so we omit it here. 826 */ 827 if (readl(&power_regs->hw_power_sts) & POWER_STS_VDD5V_GT_VDDIO) { 828 debug("SPL: 5V VDD good\n"); 829 mxs_boot_valid_5v(); 830 return; 831 } 832 833 early_delay(1000); 834 if (readl(&power_regs->hw_power_sts) & POWER_STS_VDD5V_GT_VDDIO) { 835 debug("SPL: 5V VDD good (after delay)\n"); 836 mxs_boot_valid_5v(); 837 return; 838 } 839 840 debug("SPL: 5V VDD not good\n"); 841 mxs_handle_5v_conflict(); 842 } 843 844 /** 845 * mxs_init_batt_bo() - Configure battery brownout threshold 846 * 847 * This function configures the battery input brownout threshold. The value 848 * at which the battery brownout happens is configured to 3.0V in the code. 849 */ 850 static void mxs_init_batt_bo(void) 851 { 852 struct mxs_power_regs *power_regs = 853 (struct mxs_power_regs *)MXS_POWER_BASE; 854 855 debug("SPL: Initialising battery brown-out level to 3.0V\n"); 856 857 /* Brownout at 3V */ 858 clrsetbits_le32(&power_regs->hw_power_battmonitor, 859 POWER_BATTMONITOR_BRWNOUT_LVL_MASK, 860 15 << POWER_BATTMONITOR_BRWNOUT_LVL_OFFSET); 861 862 writel(POWER_CTRL_BATT_BO_IRQ, &power_regs->hw_power_ctrl_clr); 863 writel(POWER_CTRL_ENIRQ_BATT_BO, &power_regs->hw_power_ctrl_clr); 864 } 865 866 /** 867 * mxs_switch_vddd_to_dcdc_source() - Switch VDDD rail to DC-DC converter 868 * 869 * This function turns off the VDDD linear regulator and therefore makes 870 * the VDDD rail be supplied only by the DC-DC converter. 871 */ 872 static void mxs_switch_vddd_to_dcdc_source(void) 873 { 874 struct mxs_power_regs *power_regs = 875 (struct mxs_power_regs *)MXS_POWER_BASE; 876 877 debug("SPL: Switching VDDD to DC-DC converters\n"); 878 879 clrsetbits_le32(&power_regs->hw_power_vdddctrl, 880 POWER_VDDDCTRL_LINREG_OFFSET_MASK, 881 POWER_VDDDCTRL_LINREG_OFFSET_1STEPS_BELOW); 882 883 clrbits_le32(&power_regs->hw_power_vdddctrl, 884 POWER_VDDDCTRL_DISABLE_FET | POWER_VDDDCTRL_ENABLE_LINREG | 885 POWER_VDDDCTRL_DISABLE_STEPPING); 886 } 887 888 /** 889 * mxs_power_configure_power_source() - Configure power block source 890 * 891 * This function is the core of the power configuration logic. The function 892 * selects the power block input source and configures the whole power block 893 * accordingly. After the configuration is complete and the system is stable 894 * again, the function switches the CPU clock source back to PLL. Finally, 895 * the function switches the voltage rails to DC-DC converter. 896 */ 897 static void mxs_power_configure_power_source(void) 898 { 899 int batt_ready, batt_good; 900 struct mxs_power_regs *power_regs = 901 (struct mxs_power_regs *)MXS_POWER_BASE; 902 struct mxs_lradc_regs *lradc_regs = 903 (struct mxs_lradc_regs *)MXS_LRADC_BASE; 904 905 debug("SPL: Configuring power source\n"); 906 907 mxs_power_setup_dcdc_clocksource(); 908 mxs_src_power_init(); 909 910 if (readl(&power_regs->hw_power_sts) & POWER_STS_VDD5V_GT_VDDIO) { 911 batt_ready = mxs_is_batt_ready(); 912 if (batt_ready) { 913 /* 5V source detected, good battery detected. */ 914 mxs_batt_boot(); 915 } else { 916 batt_good = mxs_is_batt_good(); 917 if (!batt_good) { 918 /* 5V source detected, bad battery detected. */ 919 writel(LRADC_CONVERSION_AUTOMATIC, 920 &lradc_regs->hw_lradc_conversion_clr); 921 clrbits_le32(&power_regs->hw_power_battmonitor, 922 POWER_BATTMONITOR_BATT_VAL_MASK); 923 } 924 mxs_5v_boot(); 925 } 926 } else { 927 /* 5V not detected, booting from battery. */ 928 mxs_batt_boot(); 929 } 930 931 /* 932 * TODO: Do not switch CPU clock to PLL if we are VDD5V is sourced 933 * from USB VBUS 934 */ 935 mxs_power_clock2pll(); 936 937 mxs_init_batt_bo(); 938 939 mxs_switch_vddd_to_dcdc_source(); 940 941 #ifdef CONFIG_MX23 942 /* Fire up the VDDMEM LinReg now that we're all set. */ 943 debug("SPL: Enabling mx23 VDDMEM linear regulator\n"); 944 writel(POWER_VDDMEMCTRL_ENABLE_LINREG | POWER_VDDMEMCTRL_ENABLE_ILIMIT, 945 &power_regs->hw_power_vddmemctrl); 946 #endif 947 } 948 949 /** 950 * mxs_enable_output_rail_protection() - Enable power rail protection 951 * 952 * This function enables overload protection on the power rails. This is 953 * triggered if the power rails' voltage drops rapidly due to overload and 954 * in such case, the supply to the powerrail is cut-off, protecting the 955 * CPU from damage. Note that under such condition, the system will likely 956 * crash or misbehave. 957 */ 958 static void mxs_enable_output_rail_protection(void) 959 { 960 struct mxs_power_regs *power_regs = 961 (struct mxs_power_regs *)MXS_POWER_BASE; 962 963 debug("SPL: Enabling output rail protection\n"); 964 965 writel(POWER_CTRL_VDDD_BO_IRQ | POWER_CTRL_VDDA_BO_IRQ | 966 POWER_CTRL_VDDIO_BO_IRQ, &power_regs->hw_power_ctrl_clr); 967 968 setbits_le32(&power_regs->hw_power_vdddctrl, 969 POWER_VDDDCTRL_PWDN_BRNOUT); 970 971 setbits_le32(&power_regs->hw_power_vddactrl, 972 POWER_VDDACTRL_PWDN_BRNOUT); 973 974 setbits_le32(&power_regs->hw_power_vddioctrl, 975 POWER_VDDIOCTRL_PWDN_BRNOUT); 976 } 977 978 /** 979 * mxs_get_vddio_power_source_off() - Get VDDIO rail power source 980 * 981 * This function tests if the VDDIO rail is supplied by linear regulator 982 * or by the DC-DC converter. Returns 1 if powered by linear regulator, 983 * returns 0 if powered by the DC-DC converter. 984 */ 985 static int mxs_get_vddio_power_source_off(void) 986 { 987 struct mxs_power_regs *power_regs = 988 (struct mxs_power_regs *)MXS_POWER_BASE; 989 uint32_t tmp; 990 991 if (readl(&power_regs->hw_power_sts) & POWER_STS_VDD5V_GT_VDDIO) { 992 tmp = readl(&power_regs->hw_power_vddioctrl); 993 if (tmp & POWER_VDDIOCTRL_DISABLE_FET) { 994 if ((tmp & POWER_VDDIOCTRL_LINREG_OFFSET_MASK) == 995 POWER_VDDIOCTRL_LINREG_OFFSET_0STEPS) { 996 return 1; 997 } 998 } 999 1000 if (!(readl(&power_regs->hw_power_5vctrl) & 1001 POWER_5VCTRL_ENABLE_DCDC)) { 1002 if ((tmp & POWER_VDDIOCTRL_LINREG_OFFSET_MASK) == 1003 POWER_VDDIOCTRL_LINREG_OFFSET_0STEPS) { 1004 return 1; 1005 } 1006 } 1007 } 1008 1009 return 0; 1010 1011 } 1012 1013 /** 1014 * mxs_get_vddd_power_source_off() - Get VDDD rail power source 1015 * 1016 * This function tests if the VDDD rail is supplied by linear regulator 1017 * or by the DC-DC converter. Returns 1 if powered by linear regulator, 1018 * returns 0 if powered by the DC-DC converter. 1019 */ 1020 static int mxs_get_vddd_power_source_off(void) 1021 { 1022 struct mxs_power_regs *power_regs = 1023 (struct mxs_power_regs *)MXS_POWER_BASE; 1024 uint32_t tmp; 1025 1026 tmp = readl(&power_regs->hw_power_vdddctrl); 1027 if (tmp & POWER_VDDDCTRL_DISABLE_FET) { 1028 if ((tmp & POWER_VDDDCTRL_LINREG_OFFSET_MASK) == 1029 POWER_VDDDCTRL_LINREG_OFFSET_0STEPS) { 1030 return 1; 1031 } 1032 } 1033 1034 if (readl(&power_regs->hw_power_sts) & POWER_STS_VDD5V_GT_VDDIO) { 1035 if (!(readl(&power_regs->hw_power_5vctrl) & 1036 POWER_5VCTRL_ENABLE_DCDC)) { 1037 return 1; 1038 } 1039 } 1040 1041 if (!(tmp & POWER_VDDDCTRL_ENABLE_LINREG)) { 1042 if ((tmp & POWER_VDDDCTRL_LINREG_OFFSET_MASK) == 1043 POWER_VDDDCTRL_LINREG_OFFSET_1STEPS_BELOW) { 1044 return 1; 1045 } 1046 } 1047 1048 return 0; 1049 } 1050 1051 struct mxs_vddx_cfg { 1052 uint32_t *reg; 1053 uint8_t step_mV; 1054 uint16_t lowest_mV; 1055 int (*powered_by_linreg)(void); 1056 uint32_t trg_mask; 1057 uint32_t bo_irq; 1058 uint32_t bo_enirq; 1059 uint32_t bo_offset_mask; 1060 uint32_t bo_offset_offset; 1061 }; 1062 1063 static const struct mxs_vddx_cfg mxs_vddio_cfg = { 1064 .reg = &(((struct mxs_power_regs *)MXS_POWER_BASE)-> 1065 hw_power_vddioctrl), 1066 #if defined(CONFIG_MX23) 1067 .step_mV = 25, 1068 #else 1069 .step_mV = 50, 1070 #endif 1071 .lowest_mV = 2800, 1072 .powered_by_linreg = mxs_get_vddio_power_source_off, 1073 .trg_mask = POWER_VDDIOCTRL_TRG_MASK, 1074 .bo_irq = POWER_CTRL_VDDIO_BO_IRQ, 1075 .bo_enirq = POWER_CTRL_ENIRQ_VDDIO_BO, 1076 .bo_offset_mask = POWER_VDDIOCTRL_BO_OFFSET_MASK, 1077 .bo_offset_offset = POWER_VDDIOCTRL_BO_OFFSET_OFFSET, 1078 }; 1079 1080 static const struct mxs_vddx_cfg mxs_vddd_cfg = { 1081 .reg = &(((struct mxs_power_regs *)MXS_POWER_BASE)-> 1082 hw_power_vdddctrl), 1083 .step_mV = 25, 1084 .lowest_mV = 800, 1085 .powered_by_linreg = mxs_get_vddd_power_source_off, 1086 .trg_mask = POWER_VDDDCTRL_TRG_MASK, 1087 .bo_irq = POWER_CTRL_VDDD_BO_IRQ, 1088 .bo_enirq = POWER_CTRL_ENIRQ_VDDD_BO, 1089 .bo_offset_mask = POWER_VDDDCTRL_BO_OFFSET_MASK, 1090 .bo_offset_offset = POWER_VDDDCTRL_BO_OFFSET_OFFSET, 1091 }; 1092 1093 #ifdef CONFIG_MX23 1094 static const struct mxs_vddx_cfg mxs_vddmem_cfg = { 1095 .reg = &(((struct mxs_power_regs *)MXS_POWER_BASE)-> 1096 hw_power_vddmemctrl), 1097 .step_mV = 50, 1098 .lowest_mV = 1700, 1099 .powered_by_linreg = NULL, 1100 .trg_mask = POWER_VDDMEMCTRL_TRG_MASK, 1101 .bo_irq = 0, 1102 .bo_enirq = 0, 1103 .bo_offset_mask = 0, 1104 .bo_offset_offset = 0, 1105 }; 1106 #endif 1107 1108 /** 1109 * mxs_power_set_vddx() - Configure voltage on DC-DC converter rail 1110 * @cfg: Configuration data of the DC-DC converter rail 1111 * @new_target: New target voltage of the DC-DC converter rail 1112 * @new_brownout: New brownout trigger voltage 1113 * 1114 * This function configures the output voltage on the DC-DC converter rail. 1115 * The rail is selected by the @cfg argument. The new voltage target is 1116 * selected by the @new_target and the voltage is specified in mV. The 1117 * new brownout value is selected by the @new_brownout argument and the 1118 * value is also in mV. 1119 */ 1120 static void mxs_power_set_vddx(const struct mxs_vddx_cfg *cfg, 1121 uint32_t new_target, uint32_t new_brownout) 1122 { 1123 struct mxs_power_regs *power_regs = 1124 (struct mxs_power_regs *)MXS_POWER_BASE; 1125 uint32_t cur_target, diff, bo_int = 0; 1126 uint32_t powered_by_linreg = 0; 1127 int adjust_up, tmp; 1128 1129 new_brownout = DIV_ROUND_CLOSEST(new_target - new_brownout, 1130 cfg->step_mV); 1131 1132 cur_target = readl(cfg->reg); 1133 cur_target &= cfg->trg_mask; 1134 cur_target *= cfg->step_mV; 1135 cur_target += cfg->lowest_mV; 1136 1137 adjust_up = new_target > cur_target; 1138 if (cfg->powered_by_linreg) 1139 powered_by_linreg = cfg->powered_by_linreg(); 1140 1141 if (adjust_up && cfg->bo_irq) { 1142 if (powered_by_linreg) { 1143 bo_int = readl(cfg->reg); 1144 clrbits_le32(cfg->reg, cfg->bo_enirq); 1145 } 1146 setbits_le32(cfg->reg, cfg->bo_offset_mask); 1147 } 1148 1149 do { 1150 if (abs(new_target - cur_target) > 100) { 1151 if (adjust_up) 1152 diff = cur_target + 100; 1153 else 1154 diff = cur_target - 100; 1155 } else { 1156 diff = new_target; 1157 } 1158 1159 diff -= cfg->lowest_mV; 1160 diff /= cfg->step_mV; 1161 1162 clrsetbits_le32(cfg->reg, cfg->trg_mask, diff); 1163 1164 if (powered_by_linreg || 1165 (readl(&power_regs->hw_power_sts) & 1166 POWER_STS_VDD5V_GT_VDDIO)) 1167 early_delay(500); 1168 else { 1169 for (;;) { 1170 tmp = readl(&power_regs->hw_power_sts); 1171 if (tmp & POWER_STS_DC_OK) 1172 break; 1173 } 1174 } 1175 1176 cur_target = readl(cfg->reg); 1177 cur_target &= cfg->trg_mask; 1178 cur_target *= cfg->step_mV; 1179 cur_target += cfg->lowest_mV; 1180 } while (new_target > cur_target); 1181 1182 if (cfg->bo_irq) { 1183 if (adjust_up && powered_by_linreg) { 1184 writel(cfg->bo_irq, &power_regs->hw_power_ctrl_clr); 1185 if (bo_int & cfg->bo_enirq) 1186 setbits_le32(cfg->reg, cfg->bo_enirq); 1187 } 1188 1189 clrsetbits_le32(cfg->reg, cfg->bo_offset_mask, 1190 new_brownout << cfg->bo_offset_offset); 1191 } 1192 } 1193 1194 /** 1195 * mxs_setup_batt_detect() - Start the battery voltage measurement logic 1196 * 1197 * This function starts and configures the LRADC block. This allows the 1198 * power initialization code to measure battery voltage and based on this 1199 * knowledge, decide whether to boot at all, boot from battery or boot 1200 * from 5V input. 1201 */ 1202 static void mxs_setup_batt_detect(void) 1203 { 1204 debug("SPL: Starting battery voltage measurement logic\n"); 1205 1206 mxs_lradc_init(); 1207 mxs_lradc_enable_batt_measurement(); 1208 early_delay(10); 1209 } 1210 1211 /** 1212 * mxs_ungate_power() - Ungate the POWER block 1213 * 1214 * This function ungates clock to the power block. In case the power block 1215 * was still gated at this point, it will not be possible to configure the 1216 * block and therefore the power initialization would fail. This function 1217 * is only needed on i.MX233, on i.MX28 the power block is always ungated. 1218 */ 1219 static void mxs_ungate_power(void) 1220 { 1221 #ifdef CONFIG_MX23 1222 struct mxs_power_regs *power_regs = 1223 (struct mxs_power_regs *)MXS_POWER_BASE; 1224 1225 writel(POWER_CTRL_CLKGATE, &power_regs->hw_power_ctrl_clr); 1226 #endif 1227 } 1228 1229 /** 1230 * mxs_power_init() - The power block init main function 1231 * 1232 * This function calls all the power block initialization functions in 1233 * proper sequence to start the power block. 1234 */ 1235 void mxs_power_init(void) 1236 { 1237 struct mxs_power_regs *power_regs = 1238 (struct mxs_power_regs *)MXS_POWER_BASE; 1239 1240 debug("SPL: Initialising Power Block\n"); 1241 1242 mxs_ungate_power(); 1243 1244 mxs_power_clock2xtal(); 1245 mxs_power_set_auto_restart(); 1246 mxs_power_set_linreg(); 1247 mxs_power_setup_5v_detect(); 1248 1249 mxs_setup_batt_detect(); 1250 1251 mxs_power_configure_power_source(); 1252 mxs_enable_output_rail_protection(); 1253 1254 debug("SPL: Setting VDDIO to 3V3 (brownout @ 3v15)\n"); 1255 mxs_power_set_vddx(&mxs_vddio_cfg, 3300, 3150); 1256 1257 debug("SPL: Setting VDDD to 1V5 (brownout @ 1v315)\n"); 1258 mxs_power_set_vddx(&mxs_vddd_cfg, 1500, 1315); 1259 #ifdef CONFIG_MX23 1260 debug("SPL: Setting mx23 VDDMEM to 2V5 (brownout @ 1v7)\n"); 1261 mxs_power_set_vddx(&mxs_vddmem_cfg, 2500, 1700); 1262 #endif 1263 writel(POWER_CTRL_VDDD_BO_IRQ | POWER_CTRL_VDDA_BO_IRQ | 1264 POWER_CTRL_VDDIO_BO_IRQ | POWER_CTRL_VDD5V_DROOP_IRQ | 1265 POWER_CTRL_VBUS_VALID_IRQ | POWER_CTRL_BATT_BO_IRQ | 1266 POWER_CTRL_DCDC4P2_BO_IRQ, &power_regs->hw_power_ctrl_clr); 1267 1268 writel(POWER_5VCTRL_PWDN_5VBRNOUT, &power_regs->hw_power_5vctrl_set); 1269 1270 early_delay(1000); 1271 } 1272 1273 #ifdef CONFIG_SPL_MXS_PSWITCH_WAIT 1274 /** 1275 * mxs_power_wait_pswitch() - Wait for power switch to be pressed 1276 * 1277 * This function waits until the power-switch was pressed to start booting 1278 * the board. 1279 */ 1280 void mxs_power_wait_pswitch(void) 1281 { 1282 struct mxs_power_regs *power_regs = 1283 (struct mxs_power_regs *)MXS_POWER_BASE; 1284 1285 debug("SPL: Waiting for power switch input\n"); 1286 while (!(readl(&power_regs->hw_power_sts) & POWER_STS_PSWITCH_MASK)) 1287 ; 1288 } 1289 #endif 1290