1 /*
2  * Freescale i.MX28 Boot PMIC init
3  *
4  * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
5  * on behalf of DENX Software Engineering GmbH
6  *
7  * SPDX-License-Identifier:	GPL-2.0+
8  */
9 
10 #include <common.h>
11 #include <config.h>
12 #include <asm/io.h>
13 #include <asm/arch/imx-regs.h>
14 
15 #include "mxs_init.h"
16 
17 #ifdef CONFIG_SYS_MXS_VDD5V_ONLY
18 #define DCDC4P2_DROPOUT_CONFIG	POWER_DCDC4P2_DROPOUT_CTRL_100MV | \
19 				POWER_DCDC4P2_DROPOUT_CTRL_SRC_4P2
20 #else
21 #define DCDC4P2_DROPOUT_CONFIG	POWER_DCDC4P2_DROPOUT_CTRL_100MV | \
22 				POWER_DCDC4P2_DROPOUT_CTRL_SRC_SEL
23 #endif
24 /**
25  * mxs_power_clock2xtal() - Switch CPU core clock source to 24MHz XTAL
26  *
27  * This function switches the CPU core clock from PLL to 24MHz XTAL
28  * oscilator. This is necessary if the PLL is being reconfigured to
29  * prevent crash of the CPU core.
30  */
31 static void mxs_power_clock2xtal(void)
32 {
33 	struct mxs_clkctrl_regs *clkctrl_regs =
34 		(struct mxs_clkctrl_regs *)MXS_CLKCTRL_BASE;
35 
36 	debug("SPL: Switching CPU clock to 24MHz XTAL\n");
37 
38 	/* Set XTAL as CPU reference clock */
39 	writel(CLKCTRL_CLKSEQ_BYPASS_CPU,
40 		&clkctrl_regs->hw_clkctrl_clkseq_set);
41 }
42 
43 /**
44  * mxs_power_clock2pll() - Switch CPU core clock source to PLL
45  *
46  * This function switches the CPU core clock from 24MHz XTAL oscilator
47  * to PLL. This can only be called once the PLL has re-locked and once
48  * the PLL is stable after reconfiguration.
49  */
50 static void mxs_power_clock2pll(void)
51 {
52 	struct mxs_clkctrl_regs *clkctrl_regs =
53 		(struct mxs_clkctrl_regs *)MXS_CLKCTRL_BASE;
54 
55 	debug("SPL: Switching CPU core clock source to PLL\n");
56 
57 	/*
58 	 * TODO: Are we really? It looks like we turn on PLL0, but we then
59 	 * set the CLKCTRL_CLKSEQ_BYPASS_CPU bit of the (which was already
60 	 * set by mxs_power_clock2xtal()). Clearing this bit here seems to
61 	 * introduce some instability (causing the CPU core to hang). Maybe
62 	 * we aren't giving PLL0 enough time to stabilise?
63 	 */
64 	setbits_le32(&clkctrl_regs->hw_clkctrl_pll0ctrl0,
65 			CLKCTRL_PLL0CTRL0_POWER);
66 	early_delay(100);
67 
68 	/*
69 	 * TODO: Should the PLL0 FORCE_LOCK bit be set here followed be a
70 	 * wait on the PLL0 LOCK bit?
71 	 */
72 	setbits_le32(&clkctrl_regs->hw_clkctrl_clkseq,
73 			CLKCTRL_CLKSEQ_BYPASS_CPU);
74 }
75 
76 /**
77  * mxs_power_set_auto_restart() - Set the auto-restart bit
78  *
79  * This function ungates the RTC block and sets the AUTO_RESTART
80  * bit to work around a design bug on MX28EVK Rev. A .
81  */
82 
83 static void mxs_power_set_auto_restart(void)
84 {
85 	struct mxs_rtc_regs *rtc_regs =
86 		(struct mxs_rtc_regs *)MXS_RTC_BASE;
87 
88 	debug("SPL: Setting auto-restart bit\n");
89 
90 	writel(RTC_CTRL_SFTRST, &rtc_regs->hw_rtc_ctrl_clr);
91 	while (readl(&rtc_regs->hw_rtc_ctrl) & RTC_CTRL_SFTRST)
92 		;
93 
94 	writel(RTC_CTRL_CLKGATE, &rtc_regs->hw_rtc_ctrl_clr);
95 	while (readl(&rtc_regs->hw_rtc_ctrl) & RTC_CTRL_CLKGATE)
96 		;
97 
98 	/* Do nothing if flag already set */
99 	if (readl(&rtc_regs->hw_rtc_persistent0) & RTC_PERSISTENT0_AUTO_RESTART)
100 		return;
101 
102 	while (readl(&rtc_regs->hw_rtc_stat) & RTC_STAT_NEW_REGS_MASK)
103 		;
104 
105 	setbits_le32(&rtc_regs->hw_rtc_persistent0,
106 			RTC_PERSISTENT0_AUTO_RESTART);
107 	writel(RTC_CTRL_FORCE_UPDATE, &rtc_regs->hw_rtc_ctrl_set);
108 	writel(RTC_CTRL_FORCE_UPDATE, &rtc_regs->hw_rtc_ctrl_clr);
109 	while (readl(&rtc_regs->hw_rtc_stat) & RTC_STAT_NEW_REGS_MASK)
110 		;
111 	while (readl(&rtc_regs->hw_rtc_stat) & RTC_STAT_STALE_REGS_MASK)
112 		;
113 }
114 
115 /**
116  * mxs_power_set_linreg() - Set linear regulators 25mV below DC-DC converter
117  *
118  * This function configures the VDDIO, VDDA and VDDD linear regulators output
119  * to be 25mV below the VDDIO, VDDA and VDDD output from the DC-DC switching
120  * converter. This is the recommended setting for the case where we use both
121  * linear regulators and DC-DC converter to power the VDDIO rail.
122  */
123 static void mxs_power_set_linreg(void)
124 {
125 	struct mxs_power_regs *power_regs =
126 		(struct mxs_power_regs *)MXS_POWER_BASE;
127 
128 	/* Set linear regulator 25mV below switching converter */
129 	debug("SPL: Setting VDDD 25mV below DC-DC converters\n");
130 	clrsetbits_le32(&power_regs->hw_power_vdddctrl,
131 			POWER_VDDDCTRL_LINREG_OFFSET_MASK,
132 			POWER_VDDDCTRL_LINREG_OFFSET_1STEPS_BELOW);
133 
134 	debug("SPL: Setting VDDA 25mV below DC-DC converters\n");
135 	clrsetbits_le32(&power_regs->hw_power_vddactrl,
136 			POWER_VDDACTRL_LINREG_OFFSET_MASK,
137 			POWER_VDDACTRL_LINREG_OFFSET_1STEPS_BELOW);
138 
139 	debug("SPL: Setting VDDIO 25mV below DC-DC converters\n");
140 	clrsetbits_le32(&power_regs->hw_power_vddioctrl,
141 			POWER_VDDIOCTRL_LINREG_OFFSET_MASK,
142 			POWER_VDDIOCTRL_LINREG_OFFSET_1STEPS_BELOW);
143 }
144 
145 /**
146  * mxs_get_batt_volt() - Measure battery input voltage
147  *
148  * This function retrieves the battery input voltage and returns it.
149  */
150 static int mxs_get_batt_volt(void)
151 {
152 	struct mxs_power_regs *power_regs =
153 		(struct mxs_power_regs *)MXS_POWER_BASE;
154 	uint32_t volt = readl(&power_regs->hw_power_battmonitor);
155 	volt &= POWER_BATTMONITOR_BATT_VAL_MASK;
156 	volt >>= POWER_BATTMONITOR_BATT_VAL_OFFSET;
157 	volt *= 8;
158 
159 	debug("SPL: Battery Voltage = %dmV\n", volt);
160 	return volt;
161 }
162 
163 /**
164  * mxs_is_batt_ready() - Test if the battery provides enough voltage to boot
165  *
166  * This function checks if the battery input voltage is higher than 3.6V and
167  * therefore allows the system to successfully boot using this power source.
168  */
169 static int mxs_is_batt_ready(void)
170 {
171 	return (mxs_get_batt_volt() >= 3600);
172 }
173 
174 /**
175  * mxs_is_batt_good() - Test if battery is operational at all
176  *
177  * This function starts recharging the battery and tests if the input current
178  * provided by the 5V input recharging the battery is also sufficient to power
179  * the DC-DC converter.
180  */
181 static int mxs_is_batt_good(void)
182 {
183 	struct mxs_power_regs *power_regs =
184 		(struct mxs_power_regs *)MXS_POWER_BASE;
185 	uint32_t volt = mxs_get_batt_volt();
186 
187 	if ((volt >= 2400) && (volt <= 4300)) {
188 		debug("SPL: Battery is good\n");
189 		return 1;
190 	}
191 
192 	clrsetbits_le32(&power_regs->hw_power_5vctrl,
193 		POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK,
194 		0x3 << POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET);
195 	writel(POWER_5VCTRL_PWD_CHARGE_4P2_MASK,
196 		&power_regs->hw_power_5vctrl_clr);
197 
198 	clrsetbits_le32(&power_regs->hw_power_charge,
199 		POWER_CHARGE_STOP_ILIMIT_MASK | POWER_CHARGE_BATTCHRG_I_MASK,
200 		POWER_CHARGE_STOP_ILIMIT_10MA | 0x3);
201 
202 	writel(POWER_CHARGE_PWD_BATTCHRG, &power_regs->hw_power_charge_clr);
203 	writel(POWER_5VCTRL_PWD_CHARGE_4P2_MASK,
204 		&power_regs->hw_power_5vctrl_clr);
205 
206 	early_delay(500000);
207 
208 	volt = mxs_get_batt_volt();
209 
210 	if (volt >= 3500) {
211 		debug("SPL: Battery Voltage too high\n");
212 		return 0;
213 	}
214 
215 	if (volt >= 2400) {
216 		debug("SPL: Battery is good\n");
217 		return 1;
218 	}
219 
220 	writel(POWER_CHARGE_STOP_ILIMIT_MASK | POWER_CHARGE_BATTCHRG_I_MASK,
221 		&power_regs->hw_power_charge_clr);
222 	writel(POWER_CHARGE_PWD_BATTCHRG, &power_regs->hw_power_charge_set);
223 
224 	debug("SPL: Battery Voltage too low\n");
225 	return 0;
226 }
227 
228 /**
229  * mxs_power_setup_5v_detect() - Start the 5V input detection comparator
230  *
231  * This function enables the 5V detection comparator and sets the 5V valid
232  * threshold to 4.4V . We use 4.4V threshold here to make sure that even
233  * under high load, the voltage drop on the 5V input won't be so critical
234  * to cause undervolt on the 4P2 linear regulator supplying the DC-DC
235  * converter and thus making the system crash.
236  */
237 static void mxs_power_setup_5v_detect(void)
238 {
239 	struct mxs_power_regs *power_regs =
240 		(struct mxs_power_regs *)MXS_POWER_BASE;
241 
242 	/* Start 5V detection */
243 	debug("SPL: Starting 5V input detection comparator\n");
244 	clrsetbits_le32(&power_regs->hw_power_5vctrl,
245 			POWER_5VCTRL_VBUSVALID_TRSH_MASK,
246 			POWER_5VCTRL_VBUSVALID_TRSH_4V4 |
247 			POWER_5VCTRL_PWRUP_VBUS_CMPS);
248 }
249 
250 /**
251  * mxs_src_power_init() - Preconfigure the power block
252  *
253  * This function configures reasonable values for the DC-DC control loop
254  * and battery monitor.
255  */
256 static void mxs_src_power_init(void)
257 {
258 	struct mxs_power_regs *power_regs =
259 		(struct mxs_power_regs *)MXS_POWER_BASE;
260 
261 	debug("SPL: Pre-Configuring power block\n");
262 
263 	/* Improve efficieny and reduce transient ripple */
264 	writel(POWER_LOOPCTRL_TOGGLE_DIF | POWER_LOOPCTRL_EN_CM_HYST |
265 		POWER_LOOPCTRL_EN_DF_HYST, &power_regs->hw_power_loopctrl_set);
266 
267 	clrsetbits_le32(&power_regs->hw_power_dclimits,
268 			POWER_DCLIMITS_POSLIMIT_BUCK_MASK,
269 			0x30 << POWER_DCLIMITS_POSLIMIT_BUCK_OFFSET);
270 
271 	setbits_le32(&power_regs->hw_power_battmonitor,
272 			POWER_BATTMONITOR_EN_BATADJ);
273 
274 	/* Increase the RCSCALE level for quick DCDC response to dynamic load */
275 	clrsetbits_le32(&power_regs->hw_power_loopctrl,
276 			POWER_LOOPCTRL_EN_RCSCALE_MASK,
277 			POWER_LOOPCTRL_RCSCALE_THRESH |
278 			POWER_LOOPCTRL_EN_RCSCALE_8X);
279 
280 	clrsetbits_le32(&power_regs->hw_power_minpwr,
281 			POWER_MINPWR_HALFFETS, POWER_MINPWR_DOUBLE_FETS);
282 
283 	/* 5V to battery handoff ... FIXME */
284 	setbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_DCDC_XFER);
285 	early_delay(30);
286 	clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_DCDC_XFER);
287 }
288 
289 /**
290  * mxs_power_init_4p2_params() - Configure the parameters of the 4P2 regulator
291  *
292  * This function configures the necessary parameters for the 4P2 linear
293  * regulator to supply the DC-DC converter from 5V input.
294  */
295 static void mxs_power_init_4p2_params(void)
296 {
297 	struct mxs_power_regs *power_regs =
298 		(struct mxs_power_regs *)MXS_POWER_BASE;
299 
300 	debug("SPL: Configuring common 4P2 regulator params\n");
301 
302 	/* Setup 4P2 parameters */
303 	clrsetbits_le32(&power_regs->hw_power_dcdc4p2,
304 		POWER_DCDC4P2_CMPTRIP_MASK | POWER_DCDC4P2_TRG_MASK,
305 		POWER_DCDC4P2_TRG_4V2 | (31 << POWER_DCDC4P2_CMPTRIP_OFFSET));
306 
307 	clrsetbits_le32(&power_regs->hw_power_5vctrl,
308 		POWER_5VCTRL_HEADROOM_ADJ_MASK,
309 		0x4 << POWER_5VCTRL_HEADROOM_ADJ_OFFSET);
310 
311 	clrsetbits_le32(&power_regs->hw_power_dcdc4p2,
312 		POWER_DCDC4P2_DROPOUT_CTRL_MASK,
313 		DCDC4P2_DROPOUT_CONFIG);
314 
315 	clrsetbits_le32(&power_regs->hw_power_5vctrl,
316 		POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK,
317 		0x3f << POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET);
318 }
319 
320 /**
321  * mxs_enable_4p2_dcdc_input() - Enable or disable the DCDC input from 4P2
322  * @xfer:	Select if the input shall be enabled or disabled
323  *
324  * This function enables or disables the 4P2 input into the DC-DC converter.
325  */
326 static void mxs_enable_4p2_dcdc_input(int xfer)
327 {
328 	struct mxs_power_regs *power_regs =
329 		(struct mxs_power_regs *)MXS_POWER_BASE;
330 	uint32_t tmp, vbus_thresh, vbus_5vdetect, pwd_bo;
331 	uint32_t prev_5v_brnout, prev_5v_droop;
332 
333 	debug("SPL: %s 4P2 DC-DC Input\n", xfer ? "Enabling" : "Disabling");
334 
335 	prev_5v_brnout = readl(&power_regs->hw_power_5vctrl) &
336 				POWER_5VCTRL_PWDN_5VBRNOUT;
337 	prev_5v_droop = readl(&power_regs->hw_power_ctrl) &
338 				POWER_CTRL_ENIRQ_VDD5V_DROOP;
339 
340 	clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_PWDN_5VBRNOUT);
341 	writel(POWER_RESET_UNLOCK_KEY | POWER_RESET_PWD_OFF,
342 		&power_regs->hw_power_reset);
343 
344 	clrbits_le32(&power_regs->hw_power_ctrl, POWER_CTRL_ENIRQ_VDD5V_DROOP);
345 
346 	if (xfer && (readl(&power_regs->hw_power_5vctrl) &
347 			POWER_5VCTRL_ENABLE_DCDC)) {
348 		return;
349 	}
350 
351 	/*
352 	 * Recording orignal values that will be modified temporarlily
353 	 * to handle a chip bug. See chip errata for CQ ENGR00115837
354 	 */
355 	tmp = readl(&power_regs->hw_power_5vctrl);
356 	vbus_thresh = tmp & POWER_5VCTRL_VBUSVALID_TRSH_MASK;
357 	vbus_5vdetect = tmp & POWER_5VCTRL_VBUSVALID_5VDETECT;
358 
359 	pwd_bo = readl(&power_regs->hw_power_minpwr) & POWER_MINPWR_PWD_BO;
360 
361 	/*
362 	 * Disable mechanisms that get erroneously tripped by when setting
363 	 * the DCDC4P2 EN_DCDC
364 	 */
365 	clrbits_le32(&power_regs->hw_power_5vctrl,
366 		POWER_5VCTRL_VBUSVALID_5VDETECT |
367 		POWER_5VCTRL_VBUSVALID_TRSH_MASK);
368 
369 	writel(POWER_MINPWR_PWD_BO, &power_regs->hw_power_minpwr_set);
370 
371 	if (xfer) {
372 		setbits_le32(&power_regs->hw_power_5vctrl,
373 				POWER_5VCTRL_DCDC_XFER);
374 		early_delay(20);
375 		clrbits_le32(&power_regs->hw_power_5vctrl,
376 				POWER_5VCTRL_DCDC_XFER);
377 
378 		setbits_le32(&power_regs->hw_power_5vctrl,
379 				POWER_5VCTRL_ENABLE_DCDC);
380 	} else {
381 		setbits_le32(&power_regs->hw_power_dcdc4p2,
382 				POWER_DCDC4P2_ENABLE_DCDC);
383 	}
384 
385 	early_delay(25);
386 
387 	clrsetbits_le32(&power_regs->hw_power_5vctrl,
388 			POWER_5VCTRL_VBUSVALID_TRSH_MASK, vbus_thresh);
389 
390 	if (vbus_5vdetect)
391 		writel(vbus_5vdetect, &power_regs->hw_power_5vctrl_set);
392 
393 	if (!pwd_bo)
394 		clrbits_le32(&power_regs->hw_power_minpwr, POWER_MINPWR_PWD_BO);
395 
396 	while (readl(&power_regs->hw_power_ctrl) & POWER_CTRL_VBUS_VALID_IRQ)
397 		writel(POWER_CTRL_VBUS_VALID_IRQ,
398 			&power_regs->hw_power_ctrl_clr);
399 
400 	if (prev_5v_brnout) {
401 		writel(POWER_5VCTRL_PWDN_5VBRNOUT,
402 			&power_regs->hw_power_5vctrl_set);
403 		writel(POWER_RESET_UNLOCK_KEY,
404 			&power_regs->hw_power_reset);
405 	} else {
406 		writel(POWER_5VCTRL_PWDN_5VBRNOUT,
407 			&power_regs->hw_power_5vctrl_clr);
408 		writel(POWER_RESET_UNLOCK_KEY | POWER_RESET_PWD_OFF,
409 			&power_regs->hw_power_reset);
410 	}
411 
412 	while (readl(&power_regs->hw_power_ctrl) & POWER_CTRL_VDD5V_DROOP_IRQ)
413 		writel(POWER_CTRL_VDD5V_DROOP_IRQ,
414 			&power_regs->hw_power_ctrl_clr);
415 
416 	if (prev_5v_droop)
417 		clrbits_le32(&power_regs->hw_power_ctrl,
418 				POWER_CTRL_ENIRQ_VDD5V_DROOP);
419 	else
420 		setbits_le32(&power_regs->hw_power_ctrl,
421 				POWER_CTRL_ENIRQ_VDD5V_DROOP);
422 }
423 
424 /**
425  * mxs_power_init_4p2_regulator() - Start the 4P2 regulator
426  *
427  * This function enables the 4P2 regulator and switches the DC-DC converter
428  * to use the 4P2 input.
429  */
430 static void mxs_power_init_4p2_regulator(void)
431 {
432 	struct mxs_power_regs *power_regs =
433 		(struct mxs_power_regs *)MXS_POWER_BASE;
434 	uint32_t tmp, tmp2;
435 
436 	debug("SPL: Enabling 4P2 regulator\n");
437 
438 	setbits_le32(&power_regs->hw_power_dcdc4p2, POWER_DCDC4P2_ENABLE_4P2);
439 
440 	writel(POWER_CHARGE_ENABLE_LOAD, &power_regs->hw_power_charge_set);
441 
442 	writel(POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK,
443 		&power_regs->hw_power_5vctrl_clr);
444 	clrbits_le32(&power_regs->hw_power_dcdc4p2, POWER_DCDC4P2_TRG_MASK);
445 
446 	/* Power up the 4p2 rail and logic/control */
447 	writel(POWER_5VCTRL_PWD_CHARGE_4P2_MASK,
448 		&power_regs->hw_power_5vctrl_clr);
449 
450 	/*
451 	 * Start charging up the 4p2 capacitor. We ramp of this charge
452 	 * gradually to avoid large inrush current from the 5V cable which can
453 	 * cause transients/problems
454 	 */
455 	debug("SPL: Charging 4P2 capacitor\n");
456 	mxs_enable_4p2_dcdc_input(0);
457 
458 	if (readl(&power_regs->hw_power_ctrl) & POWER_CTRL_VBUS_VALID_IRQ) {
459 		/*
460 		 * If we arrived here, we were unable to recover from mx23 chip
461 		 * errata 5837. 4P2 is disabled and sufficient battery power is
462 		 * not present. Exiting to not enable DCDC power during 5V
463 		 * connected state.
464 		 */
465 		clrbits_le32(&power_regs->hw_power_dcdc4p2,
466 			POWER_DCDC4P2_ENABLE_DCDC);
467 		writel(POWER_5VCTRL_PWD_CHARGE_4P2_MASK,
468 			&power_regs->hw_power_5vctrl_set);
469 
470 		debug("SPL: Unable to recover from mx23 errata 5837\n");
471 		hang();
472 	}
473 
474 	/*
475 	 * Here we set the 4p2 brownout level to something very close to 4.2V.
476 	 * We then check the brownout status. If the brownout status is false,
477 	 * the voltage is already close to the target voltage of 4.2V so we
478 	 * can go ahead and set the 4P2 current limit to our max target limit.
479 	 * If the brownout status is true, we need to ramp us the current limit
480 	 * so that we don't cause large inrush current issues. We step up the
481 	 * current limit until the brownout status is false or until we've
482 	 * reached our maximum defined 4p2 current limit.
483 	 */
484 	debug("SPL: Setting 4P2 brownout level\n");
485 	clrsetbits_le32(&power_regs->hw_power_dcdc4p2,
486 			POWER_DCDC4P2_BO_MASK,
487 			22 << POWER_DCDC4P2_BO_OFFSET);	/* 4.15V */
488 
489 	if (!(readl(&power_regs->hw_power_sts) & POWER_STS_DCDC_4P2_BO)) {
490 		setbits_le32(&power_regs->hw_power_5vctrl,
491 			0x3f << POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET);
492 	} else {
493 		tmp = (readl(&power_regs->hw_power_5vctrl) &
494 			POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK) >>
495 			POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET;
496 		while (tmp < 0x3f) {
497 			if (!(readl(&power_regs->hw_power_sts) &
498 					POWER_STS_DCDC_4P2_BO)) {
499 				tmp = readl(&power_regs->hw_power_5vctrl);
500 				tmp |= POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK;
501 				early_delay(100);
502 				writel(tmp, &power_regs->hw_power_5vctrl);
503 				break;
504 			} else {
505 				tmp++;
506 				tmp2 = readl(&power_regs->hw_power_5vctrl);
507 				tmp2 &= ~POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK;
508 				tmp2 |= tmp <<
509 					POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET;
510 				writel(tmp2, &power_regs->hw_power_5vctrl);
511 				early_delay(100);
512 			}
513 		}
514 	}
515 
516 	clrbits_le32(&power_regs->hw_power_dcdc4p2, POWER_DCDC4P2_BO_MASK);
517 	writel(POWER_CTRL_DCDC4P2_BO_IRQ, &power_regs->hw_power_ctrl_clr);
518 }
519 
520 /**
521  * mxs_power_init_dcdc_4p2_source() - Switch DC-DC converter to 4P2 source
522  *
523  * This function configures the DC-DC converter to be supplied from the 4P2
524  * linear regulator.
525  */
526 static void mxs_power_init_dcdc_4p2_source(void)
527 {
528 	struct mxs_power_regs *power_regs =
529 		(struct mxs_power_regs *)MXS_POWER_BASE;
530 
531 	debug("SPL: Switching DC-DC converters to 4P2\n");
532 
533 	if (!(readl(&power_regs->hw_power_dcdc4p2) &
534 		POWER_DCDC4P2_ENABLE_DCDC)) {
535 		debug("SPL: Already switched - aborting\n");
536 		hang();
537 	}
538 
539 	mxs_enable_4p2_dcdc_input(1);
540 
541 	if (readl(&power_regs->hw_power_ctrl) & POWER_CTRL_VBUS_VALID_IRQ) {
542 		clrbits_le32(&power_regs->hw_power_dcdc4p2,
543 			POWER_DCDC4P2_ENABLE_DCDC);
544 		writel(POWER_5VCTRL_ENABLE_DCDC,
545 			&power_regs->hw_power_5vctrl_clr);
546 		writel(POWER_5VCTRL_PWD_CHARGE_4P2_MASK,
547 			&power_regs->hw_power_5vctrl_set);
548 	}
549 }
550 
551 /**
552  * mxs_power_enable_4p2() - Power up the 4P2 regulator
553  *
554  * This function drives the process of powering up the 4P2 linear regulator
555  * and switching the DC-DC converter input over to the 4P2 linear regulator.
556  */
557 static void mxs_power_enable_4p2(void)
558 {
559 	struct mxs_power_regs *power_regs =
560 		(struct mxs_power_regs *)MXS_POWER_BASE;
561 	uint32_t vdddctrl, vddactrl, vddioctrl;
562 	uint32_t tmp;
563 
564 	debug("SPL: Powering up 4P2 regulator\n");
565 
566 	vdddctrl = readl(&power_regs->hw_power_vdddctrl);
567 	vddactrl = readl(&power_regs->hw_power_vddactrl);
568 	vddioctrl = readl(&power_regs->hw_power_vddioctrl);
569 
570 	setbits_le32(&power_regs->hw_power_vdddctrl,
571 		POWER_VDDDCTRL_DISABLE_FET | POWER_VDDDCTRL_ENABLE_LINREG |
572 		POWER_VDDDCTRL_PWDN_BRNOUT);
573 
574 	setbits_le32(&power_regs->hw_power_vddactrl,
575 		POWER_VDDACTRL_DISABLE_FET | POWER_VDDACTRL_ENABLE_LINREG |
576 		POWER_VDDACTRL_PWDN_BRNOUT);
577 
578 	setbits_le32(&power_regs->hw_power_vddioctrl,
579 		POWER_VDDIOCTRL_DISABLE_FET | POWER_VDDIOCTRL_PWDN_BRNOUT);
580 
581 	mxs_power_init_4p2_params();
582 	mxs_power_init_4p2_regulator();
583 
584 	/* Shutdown battery (none present) */
585 	if (!mxs_is_batt_ready()) {
586 		clrbits_le32(&power_regs->hw_power_dcdc4p2,
587 				POWER_DCDC4P2_BO_MASK);
588 		writel(POWER_CTRL_DCDC4P2_BO_IRQ,
589 				&power_regs->hw_power_ctrl_clr);
590 		writel(POWER_CTRL_ENIRQ_DCDC4P2_BO,
591 				&power_regs->hw_power_ctrl_clr);
592 	}
593 
594 	mxs_power_init_dcdc_4p2_source();
595 
596 	writel(vdddctrl, &power_regs->hw_power_vdddctrl);
597 	early_delay(20);
598 	writel(vddactrl, &power_regs->hw_power_vddactrl);
599 	early_delay(20);
600 	writel(vddioctrl, &power_regs->hw_power_vddioctrl);
601 
602 	/*
603 	 * Check if FET is enabled on either powerout and if so,
604 	 * disable load.
605 	 */
606 	tmp = 0;
607 	tmp |= !(readl(&power_regs->hw_power_vdddctrl) &
608 			POWER_VDDDCTRL_DISABLE_FET);
609 	tmp |= !(readl(&power_regs->hw_power_vddactrl) &
610 			POWER_VDDACTRL_DISABLE_FET);
611 	tmp |= !(readl(&power_regs->hw_power_vddioctrl) &
612 			POWER_VDDIOCTRL_DISABLE_FET);
613 	if (tmp)
614 		writel(POWER_CHARGE_ENABLE_LOAD,
615 			&power_regs->hw_power_charge_clr);
616 
617 	debug("SPL: 4P2 regulator powered-up\n");
618 }
619 
620 /**
621  * mxs_boot_valid_5v() - Boot from 5V supply
622  *
623  * This function configures the power block to boot from valid 5V input.
624  * This is called only if the 5V is reliable and can properly supply the
625  * CPU. This function proceeds to configure the 4P2 converter to be supplied
626  * from the 5V input.
627  */
628 static void mxs_boot_valid_5v(void)
629 {
630 	struct mxs_power_regs *power_regs =
631 		(struct mxs_power_regs *)MXS_POWER_BASE;
632 
633 	debug("SPL: Booting from 5V supply\n");
634 
635 	/*
636 	 * Use VBUSVALID level instead of VDD5V_GT_VDDIO level to trigger a 5V
637 	 * disconnect event. FIXME
638 	 */
639 	writel(POWER_5VCTRL_VBUSVALID_5VDETECT,
640 		&power_regs->hw_power_5vctrl_set);
641 
642 	/* Configure polarity to check for 5V disconnection. */
643 	writel(POWER_CTRL_POLARITY_VBUSVALID |
644 		POWER_CTRL_POLARITY_VDD5V_GT_VDDIO,
645 		&power_regs->hw_power_ctrl_clr);
646 
647 	writel(POWER_CTRL_VBUS_VALID_IRQ | POWER_CTRL_VDD5V_GT_VDDIO_IRQ,
648 		&power_regs->hw_power_ctrl_clr);
649 
650 	mxs_power_enable_4p2();
651 }
652 
653 /**
654  * mxs_powerdown() - Shut down the system
655  *
656  * This function powers down the CPU completely.
657  */
658 static void mxs_powerdown(void)
659 {
660 	struct mxs_power_regs *power_regs =
661 		(struct mxs_power_regs *)MXS_POWER_BASE;
662 
663 	debug("Powering Down\n");
664 
665 	writel(POWER_RESET_UNLOCK_KEY, &power_regs->hw_power_reset);
666 	writel(POWER_RESET_UNLOCK_KEY | POWER_RESET_PWD_OFF,
667 		&power_regs->hw_power_reset);
668 }
669 
670 /**
671  * mxs_batt_boot() - Configure the power block to boot from battery input
672  *
673  * This function configures the power block to boot from the battery voltage
674  * supply.
675  */
676 static void mxs_batt_boot(void)
677 {
678 	struct mxs_power_regs *power_regs =
679 		(struct mxs_power_regs *)MXS_POWER_BASE;
680 
681 	debug("SPL: Configuring power block to boot from battery\n");
682 
683 	clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_PWDN_5VBRNOUT);
684 	clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_ENABLE_DCDC);
685 
686 	clrbits_le32(&power_regs->hw_power_dcdc4p2,
687 			POWER_DCDC4P2_ENABLE_DCDC | POWER_DCDC4P2_ENABLE_4P2);
688 	writel(POWER_CHARGE_ENABLE_LOAD, &power_regs->hw_power_charge_clr);
689 
690 	/* 5V to battery handoff. */
691 	setbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_DCDC_XFER);
692 	early_delay(30);
693 	clrbits_le32(&power_regs->hw_power_5vctrl, POWER_5VCTRL_DCDC_XFER);
694 
695 	writel(POWER_CTRL_ENIRQ_DCDC4P2_BO, &power_regs->hw_power_ctrl_clr);
696 
697 	clrsetbits_le32(&power_regs->hw_power_minpwr,
698 			POWER_MINPWR_HALFFETS, POWER_MINPWR_DOUBLE_FETS);
699 
700 	mxs_power_set_linreg();
701 
702 	clrbits_le32(&power_regs->hw_power_vdddctrl,
703 		POWER_VDDDCTRL_DISABLE_FET | POWER_VDDDCTRL_ENABLE_LINREG);
704 
705 	clrbits_le32(&power_regs->hw_power_vddactrl,
706 		POWER_VDDACTRL_DISABLE_FET | POWER_VDDACTRL_ENABLE_LINREG);
707 
708 	clrbits_le32(&power_regs->hw_power_vddioctrl,
709 		POWER_VDDIOCTRL_DISABLE_FET);
710 
711 	setbits_le32(&power_regs->hw_power_5vctrl,
712 		POWER_5VCTRL_PWD_CHARGE_4P2_MASK);
713 
714 	setbits_le32(&power_regs->hw_power_5vctrl,
715 		POWER_5VCTRL_ENABLE_DCDC);
716 
717 	clrsetbits_le32(&power_regs->hw_power_5vctrl,
718 		POWER_5VCTRL_CHARGE_4P2_ILIMIT_MASK,
719 		0x8 << POWER_5VCTRL_CHARGE_4P2_ILIMIT_OFFSET);
720 
721 	mxs_power_enable_4p2();
722 }
723 
724 /**
725  * mxs_handle_5v_conflict() - Test if the 5V input is reliable
726  *
727  * This function tests if the 5V input can reliably supply the system. If it
728  * can, then proceed to configuring the system to boot from 5V source, otherwise
729  * try booting from battery supply. If we can not boot from battery supply
730  * either, shut down the system.
731  */
732 static void mxs_handle_5v_conflict(void)
733 {
734 	struct mxs_power_regs *power_regs =
735 		(struct mxs_power_regs *)MXS_POWER_BASE;
736 	uint32_t tmp;
737 
738 	debug("SPL: Resolving 5V conflict\n");
739 
740 	setbits_le32(&power_regs->hw_power_vddioctrl,
741 			POWER_VDDIOCTRL_BO_OFFSET_MASK);
742 
743 	for (;;) {
744 		tmp = readl(&power_regs->hw_power_sts);
745 
746 		if (tmp & POWER_STS_VDDIO_BO) {
747 			/*
748 			 * VDDIO has a brownout, then the VDD5V_GT_VDDIO becomes
749 			 * unreliable
750 			 */
751 			debug("SPL: VDDIO has a brownout\n");
752 			mxs_powerdown();
753 			break;
754 		}
755 
756 		if (tmp & POWER_STS_VDD5V_GT_VDDIO) {
757 			debug("SPL: POWER_STS_VDD5V_GT_VDDIO is set\n");
758 			mxs_boot_valid_5v();
759 			break;
760 		} else {
761 			debug("SPL: POWER_STS_VDD5V_GT_VDDIO is not set\n");
762 			mxs_powerdown();
763 			break;
764 		}
765 
766 		/*
767 		 * TODO: I can't see this being reached. We'll either
768 		 * powerdown or boot from a stable 5V supply.
769 		 */
770 		if (tmp & POWER_STS_PSWITCH_MASK) {
771 			debug("SPL: POWER_STS_PSWITCH_MASK is set\n");
772 			mxs_batt_boot();
773 			break;
774 		}
775 	}
776 }
777 
778 /**
779  * mxs_5v_boot() - Configure the power block to boot from 5V input
780  *
781  * This function handles configuration of the power block when supplied by
782  * a 5V input.
783  */
784 static void mxs_5v_boot(void)
785 {
786 	struct mxs_power_regs *power_regs =
787 		(struct mxs_power_regs *)MXS_POWER_BASE;
788 
789 	debug("SPL: Configuring power block to boot from 5V input\n");
790 
791 	/*
792 	 * NOTE: In original IMX-Bootlets, this also checks for VBUSVALID,
793 	 * but their implementation always returns 1 so we omit it here.
794 	 */
795 	if (readl(&power_regs->hw_power_sts) & POWER_STS_VDD5V_GT_VDDIO) {
796 		debug("SPL: 5V VDD good\n");
797 		mxs_boot_valid_5v();
798 		return;
799 	}
800 
801 	early_delay(1000);
802 	if (readl(&power_regs->hw_power_sts) & POWER_STS_VDD5V_GT_VDDIO) {
803 		debug("SPL: 5V VDD good (after delay)\n");
804 		mxs_boot_valid_5v();
805 		return;
806 	}
807 
808 	debug("SPL: 5V VDD not good\n");
809 	mxs_handle_5v_conflict();
810 }
811 
812 /**
813  * mxs_init_batt_bo() - Configure battery brownout threshold
814  *
815  * This function configures the battery input brownout threshold. The value
816  * at which the battery brownout happens is configured to 3.0V in the code.
817  */
818 static void mxs_init_batt_bo(void)
819 {
820 	struct mxs_power_regs *power_regs =
821 		(struct mxs_power_regs *)MXS_POWER_BASE;
822 
823 	debug("SPL: Initialising battery brown-out level to 3.0V\n");
824 
825 	/* Brownout at 3V */
826 	clrsetbits_le32(&power_regs->hw_power_battmonitor,
827 		POWER_BATTMONITOR_BRWNOUT_LVL_MASK,
828 		15 << POWER_BATTMONITOR_BRWNOUT_LVL_OFFSET);
829 
830 	writel(POWER_CTRL_BATT_BO_IRQ, &power_regs->hw_power_ctrl_clr);
831 	writel(POWER_CTRL_ENIRQ_BATT_BO, &power_regs->hw_power_ctrl_clr);
832 }
833 
834 /**
835  * mxs_switch_vddd_to_dcdc_source() - Switch VDDD rail to DC-DC converter
836  *
837  * This function turns off the VDDD linear regulator and therefore makes
838  * the VDDD rail be supplied only by the DC-DC converter.
839  */
840 static void mxs_switch_vddd_to_dcdc_source(void)
841 {
842 	struct mxs_power_regs *power_regs =
843 		(struct mxs_power_regs *)MXS_POWER_BASE;
844 
845 	debug("SPL: Switching VDDD to DC-DC converters\n");
846 
847 	clrsetbits_le32(&power_regs->hw_power_vdddctrl,
848 		POWER_VDDDCTRL_LINREG_OFFSET_MASK,
849 		POWER_VDDDCTRL_LINREG_OFFSET_1STEPS_BELOW);
850 
851 	clrbits_le32(&power_regs->hw_power_vdddctrl,
852 		POWER_VDDDCTRL_DISABLE_FET | POWER_VDDDCTRL_ENABLE_LINREG |
853 		POWER_VDDDCTRL_DISABLE_STEPPING);
854 }
855 
856 /**
857  * mxs_power_configure_power_source() - Configure power block source
858  *
859  * This function is the core of the power configuration logic. The function
860  * selects the power block input source and configures the whole power block
861  * accordingly. After the configuration is complete and the system is stable
862  * again, the function switches the CPU clock source back to PLL. Finally,
863  * the function switches the voltage rails to DC-DC converter.
864  */
865 static void mxs_power_configure_power_source(void)
866 {
867 	int batt_ready, batt_good;
868 	struct mxs_power_regs *power_regs =
869 		(struct mxs_power_regs *)MXS_POWER_BASE;
870 	struct mxs_lradc_regs *lradc_regs =
871 		(struct mxs_lradc_regs *)MXS_LRADC_BASE;
872 
873 	debug("SPL: Configuring power source\n");
874 
875 	mxs_src_power_init();
876 
877 	if (readl(&power_regs->hw_power_sts) & POWER_STS_VDD5V_GT_VDDIO) {
878 		batt_ready = mxs_is_batt_ready();
879 		if (batt_ready) {
880 			/* 5V source detected, good battery detected. */
881 			mxs_batt_boot();
882 		} else {
883 			batt_good = mxs_is_batt_good();
884 			if (!batt_good) {
885 				/* 5V source detected, bad battery detected. */
886 				writel(LRADC_CONVERSION_AUTOMATIC,
887 					&lradc_regs->hw_lradc_conversion_clr);
888 				clrbits_le32(&power_regs->hw_power_battmonitor,
889 					POWER_BATTMONITOR_BATT_VAL_MASK);
890 			}
891 			mxs_5v_boot();
892 		}
893 	} else {
894 		/* 5V not detected, booting from battery. */
895 		mxs_batt_boot();
896 	}
897 
898 	/*
899 	 * TODO: Do not switch CPU clock to PLL if we are VDD5V is sourced
900 	 * from USB VBUS
901 	 */
902 	mxs_power_clock2pll();
903 
904 	mxs_init_batt_bo();
905 
906 	mxs_switch_vddd_to_dcdc_source();
907 
908 #ifdef CONFIG_MX23
909 	/* Fire up the VDDMEM LinReg now that we're all set. */
910 	debug("SPL: Enabling mx23 VDDMEM linear regulator\n");
911 	writel(POWER_VDDMEMCTRL_ENABLE_LINREG | POWER_VDDMEMCTRL_ENABLE_ILIMIT,
912 		&power_regs->hw_power_vddmemctrl);
913 #endif
914 }
915 
916 /**
917  * mxs_enable_output_rail_protection() - Enable power rail protection
918  *
919  * This function enables overload protection on the power rails. This is
920  * triggered if the power rails' voltage drops rapidly due to overload and
921  * in such case, the supply to the powerrail is cut-off, protecting the
922  * CPU from damage. Note that under such condition, the system will likely
923  * crash or misbehave.
924  */
925 static void mxs_enable_output_rail_protection(void)
926 {
927 	struct mxs_power_regs *power_regs =
928 		(struct mxs_power_regs *)MXS_POWER_BASE;
929 
930 	debug("SPL: Enabling output rail protection\n");
931 
932 	writel(POWER_CTRL_VDDD_BO_IRQ | POWER_CTRL_VDDA_BO_IRQ |
933 		POWER_CTRL_VDDIO_BO_IRQ, &power_regs->hw_power_ctrl_clr);
934 
935 	setbits_le32(&power_regs->hw_power_vdddctrl,
936 			POWER_VDDDCTRL_PWDN_BRNOUT);
937 
938 	setbits_le32(&power_regs->hw_power_vddactrl,
939 			POWER_VDDACTRL_PWDN_BRNOUT);
940 
941 	setbits_le32(&power_regs->hw_power_vddioctrl,
942 			POWER_VDDIOCTRL_PWDN_BRNOUT);
943 }
944 
945 /**
946  * mxs_get_vddio_power_source_off() - Get VDDIO rail power source
947  *
948  * This function tests if the VDDIO rail is supplied by linear regulator
949  * or by the DC-DC converter. Returns 1 if powered by linear regulator,
950  * returns 0 if powered by the DC-DC converter.
951  */
952 static int mxs_get_vddio_power_source_off(void)
953 {
954 	struct mxs_power_regs *power_regs =
955 		(struct mxs_power_regs *)MXS_POWER_BASE;
956 	uint32_t tmp;
957 
958 	if (readl(&power_regs->hw_power_sts) & POWER_STS_VDD5V_GT_VDDIO) {
959 		tmp = readl(&power_regs->hw_power_vddioctrl);
960 		if (tmp & POWER_VDDIOCTRL_DISABLE_FET) {
961 			if ((tmp & POWER_VDDIOCTRL_LINREG_OFFSET_MASK) ==
962 				POWER_VDDIOCTRL_LINREG_OFFSET_0STEPS) {
963 				return 1;
964 			}
965 		}
966 
967 		if (!(readl(&power_regs->hw_power_5vctrl) &
968 			POWER_5VCTRL_ENABLE_DCDC)) {
969 			if ((tmp & POWER_VDDIOCTRL_LINREG_OFFSET_MASK) ==
970 				POWER_VDDIOCTRL_LINREG_OFFSET_0STEPS) {
971 				return 1;
972 			}
973 		}
974 	}
975 
976 	return 0;
977 
978 }
979 
980 /**
981  * mxs_get_vddd_power_source_off() - Get VDDD rail power source
982  *
983  * This function tests if the VDDD rail is supplied by linear regulator
984  * or by the DC-DC converter. Returns 1 if powered by linear regulator,
985  * returns 0 if powered by the DC-DC converter.
986  */
987 static int mxs_get_vddd_power_source_off(void)
988 {
989 	struct mxs_power_regs *power_regs =
990 		(struct mxs_power_regs *)MXS_POWER_BASE;
991 	uint32_t tmp;
992 
993 	tmp = readl(&power_regs->hw_power_vdddctrl);
994 	if (tmp & POWER_VDDDCTRL_DISABLE_FET) {
995 		if ((tmp & POWER_VDDDCTRL_LINREG_OFFSET_MASK) ==
996 			POWER_VDDDCTRL_LINREG_OFFSET_0STEPS) {
997 			return 1;
998 		}
999 	}
1000 
1001 	if (readl(&power_regs->hw_power_sts) & POWER_STS_VDD5V_GT_VDDIO) {
1002 		if (!(readl(&power_regs->hw_power_5vctrl) &
1003 			POWER_5VCTRL_ENABLE_DCDC)) {
1004 			return 1;
1005 		}
1006 	}
1007 
1008 	if (!(tmp & POWER_VDDDCTRL_ENABLE_LINREG)) {
1009 		if ((tmp & POWER_VDDDCTRL_LINREG_OFFSET_MASK) ==
1010 			POWER_VDDDCTRL_LINREG_OFFSET_1STEPS_BELOW) {
1011 			return 1;
1012 		}
1013 	}
1014 
1015 	return 0;
1016 }
1017 
1018 struct mxs_vddx_cfg {
1019 	uint32_t		*reg;
1020 	uint8_t			step_mV;
1021 	uint16_t		lowest_mV;
1022 	int			(*powered_by_linreg)(void);
1023 	uint32_t		trg_mask;
1024 	uint32_t		bo_irq;
1025 	uint32_t		bo_enirq;
1026 	uint32_t		bo_offset_mask;
1027 	uint32_t		bo_offset_offset;
1028 };
1029 
1030 static const struct mxs_vddx_cfg mxs_vddio_cfg = {
1031 	.reg			= &(((struct mxs_power_regs *)MXS_POWER_BASE)->
1032 					hw_power_vddioctrl),
1033 #if defined(CONFIG_MX23)
1034 	.step_mV		= 25,
1035 #else
1036 	.step_mV		= 50,
1037 #endif
1038 	.lowest_mV		= 2800,
1039 	.powered_by_linreg	= mxs_get_vddio_power_source_off,
1040 	.trg_mask		= POWER_VDDIOCTRL_TRG_MASK,
1041 	.bo_irq			= POWER_CTRL_VDDIO_BO_IRQ,
1042 	.bo_enirq		= POWER_CTRL_ENIRQ_VDDIO_BO,
1043 	.bo_offset_mask		= POWER_VDDIOCTRL_BO_OFFSET_MASK,
1044 	.bo_offset_offset	= POWER_VDDIOCTRL_BO_OFFSET_OFFSET,
1045 };
1046 
1047 static const struct mxs_vddx_cfg mxs_vddd_cfg = {
1048 	.reg			= &(((struct mxs_power_regs *)MXS_POWER_BASE)->
1049 					hw_power_vdddctrl),
1050 	.step_mV		= 25,
1051 	.lowest_mV		= 800,
1052 	.powered_by_linreg	= mxs_get_vddd_power_source_off,
1053 	.trg_mask		= POWER_VDDDCTRL_TRG_MASK,
1054 	.bo_irq			= POWER_CTRL_VDDD_BO_IRQ,
1055 	.bo_enirq		= POWER_CTRL_ENIRQ_VDDD_BO,
1056 	.bo_offset_mask		= POWER_VDDDCTRL_BO_OFFSET_MASK,
1057 	.bo_offset_offset	= POWER_VDDDCTRL_BO_OFFSET_OFFSET,
1058 };
1059 
1060 #ifdef CONFIG_MX23
1061 static const struct mxs_vddx_cfg mxs_vddmem_cfg = {
1062 	.reg			= &(((struct mxs_power_regs *)MXS_POWER_BASE)->
1063 					hw_power_vddmemctrl),
1064 	.step_mV		= 50,
1065 	.lowest_mV		= 1700,
1066 	.powered_by_linreg	= NULL,
1067 	.trg_mask		= POWER_VDDMEMCTRL_TRG_MASK,
1068 	.bo_irq			= 0,
1069 	.bo_enirq		= 0,
1070 	.bo_offset_mask		= 0,
1071 	.bo_offset_offset	= 0,
1072 };
1073 #endif
1074 
1075 /**
1076  * mxs_power_set_vddx() - Configure voltage on DC-DC converter rail
1077  * @cfg:		Configuration data of the DC-DC converter rail
1078  * @new_target:		New target voltage of the DC-DC converter rail
1079  * @new_brownout:	New brownout trigger voltage
1080  *
1081  * This function configures the output voltage on the DC-DC converter rail.
1082  * The rail is selected by the @cfg argument. The new voltage target is
1083  * selected by the @new_target and the voltage is specified in mV. The
1084  * new brownout value is selected by the @new_brownout argument and the
1085  * value is also in mV.
1086  */
1087 static void mxs_power_set_vddx(const struct mxs_vddx_cfg *cfg,
1088 				uint32_t new_target, uint32_t new_brownout)
1089 {
1090 	struct mxs_power_regs *power_regs =
1091 		(struct mxs_power_regs *)MXS_POWER_BASE;
1092 	uint32_t cur_target, diff, bo_int = 0;
1093 	uint32_t powered_by_linreg = 0;
1094 	int adjust_up, tmp;
1095 
1096 	new_brownout = DIV_ROUND_CLOSEST(new_target - new_brownout,
1097 					 cfg->step_mV);
1098 
1099 	cur_target = readl(cfg->reg);
1100 	cur_target &= cfg->trg_mask;
1101 	cur_target *= cfg->step_mV;
1102 	cur_target += cfg->lowest_mV;
1103 
1104 	adjust_up = new_target > cur_target;
1105 	if (cfg->powered_by_linreg)
1106 		powered_by_linreg = cfg->powered_by_linreg();
1107 
1108 	if (adjust_up && cfg->bo_irq) {
1109 		if (powered_by_linreg) {
1110 			bo_int = readl(cfg->reg);
1111 			clrbits_le32(cfg->reg, cfg->bo_enirq);
1112 		}
1113 		setbits_le32(cfg->reg, cfg->bo_offset_mask);
1114 	}
1115 
1116 	do {
1117 		if (abs(new_target - cur_target) > 100) {
1118 			if (adjust_up)
1119 				diff = cur_target + 100;
1120 			else
1121 				diff = cur_target - 100;
1122 		} else {
1123 			diff = new_target;
1124 		}
1125 
1126 		diff -= cfg->lowest_mV;
1127 		diff /= cfg->step_mV;
1128 
1129 		clrsetbits_le32(cfg->reg, cfg->trg_mask, diff);
1130 
1131 		if (powered_by_linreg ||
1132 			(readl(&power_regs->hw_power_sts) &
1133 				POWER_STS_VDD5V_GT_VDDIO))
1134 			early_delay(500);
1135 		else {
1136 			for (;;) {
1137 				tmp = readl(&power_regs->hw_power_sts);
1138 				if (tmp & POWER_STS_DC_OK)
1139 					break;
1140 			}
1141 		}
1142 
1143 		cur_target = readl(cfg->reg);
1144 		cur_target &= cfg->trg_mask;
1145 		cur_target *= cfg->step_mV;
1146 		cur_target += cfg->lowest_mV;
1147 	} while (new_target > cur_target);
1148 
1149 	if (cfg->bo_irq) {
1150 		if (adjust_up && powered_by_linreg) {
1151 			writel(cfg->bo_irq, &power_regs->hw_power_ctrl_clr);
1152 			if (bo_int & cfg->bo_enirq)
1153 				setbits_le32(cfg->reg, cfg->bo_enirq);
1154 		}
1155 
1156 		clrsetbits_le32(cfg->reg, cfg->bo_offset_mask,
1157 				new_brownout << cfg->bo_offset_offset);
1158 	}
1159 }
1160 
1161 /**
1162  * mxs_setup_batt_detect() - Start the battery voltage measurement logic
1163  *
1164  * This function starts and configures the LRADC block. This allows the
1165  * power initialization code to measure battery voltage and based on this
1166  * knowledge, decide whether to boot at all, boot from battery or boot
1167  * from 5V input.
1168  */
1169 static void mxs_setup_batt_detect(void)
1170 {
1171 	debug("SPL: Starting battery voltage measurement logic\n");
1172 
1173 	mxs_lradc_init();
1174 	mxs_lradc_enable_batt_measurement();
1175 	early_delay(10);
1176 }
1177 
1178 /**
1179  * mxs_ungate_power() - Ungate the POWER block
1180  *
1181  * This function ungates clock to the power block. In case the power block
1182  * was still gated at this point, it will not be possible to configure the
1183  * block and therefore the power initialization would fail. This function
1184  * is only needed on i.MX233, on i.MX28 the power block is always ungated.
1185  */
1186 static void mxs_ungate_power(void)
1187 {
1188 #ifdef CONFIG_MX23
1189 	struct mxs_power_regs *power_regs =
1190 		(struct mxs_power_regs *)MXS_POWER_BASE;
1191 
1192 	writel(POWER_CTRL_CLKGATE, &power_regs->hw_power_ctrl_clr);
1193 #endif
1194 }
1195 
1196 /**
1197  * mxs_power_init() - The power block init main function
1198  *
1199  * This function calls all the power block initialization functions in
1200  * proper sequence to start the power block.
1201  */
1202 void mxs_power_init(void)
1203 {
1204 	struct mxs_power_regs *power_regs =
1205 		(struct mxs_power_regs *)MXS_POWER_BASE;
1206 
1207 	debug("SPL: Initialising Power Block\n");
1208 
1209 	mxs_ungate_power();
1210 
1211 	mxs_power_clock2xtal();
1212 	mxs_power_set_auto_restart();
1213 	mxs_power_set_linreg();
1214 	mxs_power_setup_5v_detect();
1215 
1216 	mxs_setup_batt_detect();
1217 
1218 	mxs_power_configure_power_source();
1219 	mxs_enable_output_rail_protection();
1220 
1221 	debug("SPL: Setting VDDIO to 3V3 (brownout @ 3v15)\n");
1222 	mxs_power_set_vddx(&mxs_vddio_cfg, 3300, 3150);
1223 
1224 	debug("SPL: Setting VDDD to 1V5 (brownout @ 1v0)\n");
1225 	mxs_power_set_vddx(&mxs_vddd_cfg, 1500, 1000);
1226 #ifdef CONFIG_MX23
1227 	debug("SPL: Setting mx23 VDDMEM to 2V5 (brownout @ 1v7)\n");
1228 	mxs_power_set_vddx(&mxs_vddmem_cfg, 2500, 1700);
1229 #endif
1230 	writel(POWER_CTRL_VDDD_BO_IRQ | POWER_CTRL_VDDA_BO_IRQ |
1231 		POWER_CTRL_VDDIO_BO_IRQ | POWER_CTRL_VDD5V_DROOP_IRQ |
1232 		POWER_CTRL_VBUS_VALID_IRQ | POWER_CTRL_BATT_BO_IRQ |
1233 		POWER_CTRL_DCDC4P2_BO_IRQ, &power_regs->hw_power_ctrl_clr);
1234 
1235 	writel(POWER_5VCTRL_PWDN_5VBRNOUT, &power_regs->hw_power_5vctrl_set);
1236 
1237 	early_delay(1000);
1238 }
1239 
1240 #ifdef	CONFIG_SPL_MXS_PSWITCH_WAIT
1241 /**
1242  * mxs_power_wait_pswitch() - Wait for power switch to be pressed
1243  *
1244  * This function waits until the power-switch was pressed to start booting
1245  * the board.
1246  */
1247 void mxs_power_wait_pswitch(void)
1248 {
1249 	struct mxs_power_regs *power_regs =
1250 		(struct mxs_power_regs *)MXS_POWER_BASE;
1251 
1252 	debug("SPL: Waiting for power switch input\n");
1253 	while (!(readl(&power_regs->hw_power_sts) & POWER_STS_PSWITCH_MASK))
1254 		;
1255 }
1256 #endif
1257