1menu "ARM architecture" 2 depends on ARM 3 4config SYS_ARCH 5 default "arm" 6 7config ARM64 8 bool 9 select PHYS_64BIT 10 select SYS_CACHE_SHIFT_6 11 12if ARM64 13config POSITION_INDEPENDENT 14 bool "Generate position-independent pre-relocation code" 15 help 16 U-Boot expects to be linked to a specific hard-coded address, and to 17 be loaded to and run from that address. This option lifts that 18 restriction, thus allowing the code to be loaded to and executed 19 from almost any address. This logic relies on the relocation 20 information that is embedded into the binary to support U-Boot 21 relocating itself to the top-of-RAM later during execution. 22 23config SYS_INIT_SP_BSS_OFFSET 24 int 25 help 26 U-Boot typically uses a hard-coded value for the stack pointer 27 before relocation. Define this option to instead calculate the 28 initial SP at run-time. This is useful to avoid hard-coding addresses 29 into U-Boot, so that can be loaded and executed at arbitrary 30 addresses and thus avoid using arbitrary addresses at runtime. This 31 option's value is the offset added to &_bss_start in order to 32 calculate the stack pointer. This offset should be large enough so 33 that the early malloc region, global data (gd), and early stack usage 34 do not overlap any appended DTB. 35 36config LINUX_KERNEL_IMAGE_HEADER 37 bool 38 help 39 Place a Linux kernel image header at the start of the U-Boot binary. 40 The format of the header is described in the Linux kernel source at 41 Documentation/arm64/booting.txt. This feature is useful since the 42 image header reports the amount of memory (BSS and similar) that 43 U-Boot needs to use, but which isn't part of the binary. 44 45if LINUX_KERNEL_IMAGE_HEADER 46config LNX_KRNL_IMG_TEXT_OFFSET_BASE 47 hex 48 help 49 The value subtracted from CONFIG_SYS_TEXT_BASE to calculate the 50 TEXT_OFFSET value written in to the Linux kernel image header. 51endif 52endif 53 54config STATIC_RELA 55 bool 56 default y if ARM64 && !POSITION_INDEPENDENT 57 58config DMA_ADDR_T_64BIT 59 bool 60 default y if ARM64 61 62config HAS_VBAR 63 bool 64 65config HAS_THUMB2 66 bool 67 68# Used for compatibility with asm files copied from the kernel 69config ARM_ASM_UNIFIED 70 bool 71 default y 72 73# Used for compatibility with asm files copied from the kernel 74config THUMB2_KERNEL 75 bool 76 77# If set, the workarounds for these ARM errata are applied early during U-Boot 78# startup. Note that in general these options force the workarounds to be 79# applied; no CPU-type/version detection exists, unlike the similar options in 80# the Linux kernel. Do not set these options unless they apply! Also note that 81# the following can be machine specific errata. These do have ability to 82# provide rudimentary version and machine specific checks, but expect no 83# product checks: 84# CONFIG_ARM_ERRATA_430973 85# CONFIG_ARM_ERRATA_454179 86# CONFIG_ARM_ERRATA_621766 87# CONFIG_ARM_ERRATA_798870 88# CONFIG_ARM_ERRATA_801819 89config ARM_ERRATA_430973 90 bool 91 92config ARM_ERRATA_454179 93 bool 94 95config ARM_ERRATA_621766 96 bool 97 98config ARM_ERRATA_716044 99 bool 100 101config ARM_ERRATA_725233 102 bool 103 104config ARM_ERRATA_742230 105 bool 106 107config ARM_ERRATA_743622 108 bool 109 110config ARM_ERRATA_751472 111 bool 112 113config ARM_ERRATA_761320 114 bool 115 116config ARM_ERRATA_773022 117 bool 118 119config ARM_ERRATA_774769 120 bool 121 122config ARM_ERRATA_794072 123 bool 124 125config ARM_ERRATA_798870 126 bool 127 128config ARM_ERRATA_801819 129 bool 130 131config ARM_ERRATA_826974 132 bool 133 134config ARM_ERRATA_828024 135 bool 136 137config ARM_ERRATA_829520 138 bool 139 140config ARM_ERRATA_833069 141 bool 142 143config ARM_ERRATA_833471 144 bool 145 146config ARM_ERRATA_845369 147 bool 148 149config ARM_ERRATA_852421 150 bool 151 152config ARM_ERRATA_852423 153 bool 154 155config ARM_ERRATA_855873 156 bool 157 158config CPU_ARM720T 159 bool 160 select SYS_CACHE_SHIFT_5 161 162config CPU_ARM920T 163 bool 164 select SYS_CACHE_SHIFT_5 165 166config CPU_ARM926EJS 167 bool 168 select SYS_CACHE_SHIFT_5 169 170config CPU_ARM946ES 171 bool 172 select SYS_CACHE_SHIFT_5 173 174config CPU_ARM1136 175 bool 176 select SYS_CACHE_SHIFT_5 177 178config CPU_ARM1176 179 bool 180 select HAS_VBAR 181 select SYS_CACHE_SHIFT_5 182 183config CPU_V7 184 bool 185 select HAS_VBAR 186 select HAS_THUMB2 187 select SYS_CACHE_SHIFT_6 188 189config CPU_V7M 190 bool 191 select HAS_THUMB2 192 select THUMB2_KERNEL 193 select SYS_CACHE_SHIFT_5 194 195config CPU_PXA 196 bool 197 select SYS_CACHE_SHIFT_5 198 199config CPU_SA1100 200 bool 201 select SYS_CACHE_SHIFT_5 202 203config SYS_CPU 204 default "arm720t" if CPU_ARM720T 205 default "arm920t" if CPU_ARM920T 206 default "arm926ejs" if CPU_ARM926EJS 207 default "arm946es" if CPU_ARM946ES 208 default "arm1136" if CPU_ARM1136 209 default "arm1176" if CPU_ARM1176 210 default "armv7" if CPU_V7 211 default "armv7m" if CPU_V7M 212 default "pxa" if CPU_PXA 213 default "sa1100" if CPU_SA1100 214 default "armv8" if ARM64 215 216config SYS_ARM_ARCH 217 int 218 default 4 if CPU_ARM720T 219 default 4 if CPU_ARM920T 220 default 5 if CPU_ARM926EJS 221 default 5 if CPU_ARM946ES 222 default 6 if CPU_ARM1136 223 default 6 if CPU_ARM1176 224 default 7 if CPU_V7 225 default 7 if CPU_V7M 226 default 5 if CPU_PXA 227 default 4 if CPU_SA1100 228 default 8 if ARM64 229 230config SYS_CACHE_SHIFT_5 231 bool 232 233config SYS_CACHE_SHIFT_6 234 bool 235 236config SYS_CACHE_SHIFT_7 237 bool 238 239config SYS_CACHELINE_SIZE 240 int 241 default 128 if SYS_CACHE_SHIFT_7 242 default 64 if SYS_CACHE_SHIFT_6 243 default 32 if SYS_CACHE_SHIFT_5 244 245config ARM_SMCCC 246 bool "Support for ARM SMC Calling Convention (SMCCC)" 247 depends on CPU_V7 || ARM64 248 select ARM_PSCI_FW 249 help 250 Say Y here if you want to enable ARM SMC Calling Convention. 251 This should be enabled if U-Boot needs to communicate with system 252 firmware (for example, PSCI) according to SMCCC. 253 254config SEMIHOSTING 255 bool "support boot from semihosting" 256 help 257 In emulated environments, semihosting is a way for 258 the hosted environment to call out to the emulator to 259 retrieve files from the host machine. 260 261config SYS_THUMB_BUILD 262 bool "Build U-Boot using the Thumb instruction set" 263 depends on !ARM64 264 help 265 Use this flag to build U-Boot using the Thumb instruction set for 266 ARM architectures. Thumb instruction set provides better code 267 density. For ARM architectures that support Thumb2 this flag will 268 result in Thumb2 code generated by GCC. 269 270config SPL_SYS_THUMB_BUILD 271 bool "Build SPL using the Thumb instruction set" 272 default y if SYS_THUMB_BUILD 273 depends on !ARM64 274 help 275 Use this flag to build SPL using the Thumb instruction set for 276 ARM architectures. Thumb instruction set provides better code 277 density. For ARM architectures that support Thumb2 this flag will 278 result in Thumb2 code generated by GCC. 279 280config SYS_L2CACHE_OFF 281 bool "L2cache off" 282 help 283 If SoC does not support L2CACHE or one do not want to enable 284 L2CACHE, choose this option. 285 286config ENABLE_ARM_SOC_BOOT0_HOOK 287 bool "prepare BOOT0 header" 288 help 289 If the SoC's BOOT0 requires a header area filled with (magic) 290 values, then choose this option, and create a define called 291 ARM_SOC_BOOT0_HOOK which contains the required assembler 292 preprocessor code. 293 294config ARM_CORTEX_CPU_IS_UP 295 bool 296 default n 297 298config USE_ARCH_MEMCPY 299 bool "Use an assembly optimized implementation of memcpy" 300 default y 301 depends on !ARM64 302 help 303 Enable the generation of an optimized version of memcpy. 304 Such implementation may be faster under some conditions 305 but may increase the binary size. 306 307config SPL_USE_ARCH_MEMCPY 308 bool "Use an assembly optimized implementation of memcpy for SPL" 309 default y if USE_ARCH_MEMCPY 310 depends on !ARM64 311 help 312 Enable the generation of an optimized version of memcpy. 313 Such implementation may be faster under some conditions 314 but may increase the binary size. 315 316config USE_ARCH_MEMSET 317 bool "Use an assembly optimized implementation of memset" 318 default y 319 depends on !ARM64 320 help 321 Enable the generation of an optimized version of memset. 322 Such implementation may be faster under some conditions 323 but may increase the binary size. 324 325config SPL_USE_ARCH_MEMSET 326 bool "Use an assembly optimized implementation of memset for SPL" 327 default y if USE_ARCH_MEMSET 328 depends on !ARM64 329 help 330 Enable the generation of an optimized version of memset. 331 Such implementation may be faster under some conditions 332 but may increase the binary size. 333 334config ARM64_SUPPORT_AARCH32 335 bool "ARM64 system support AArch32 execution state" 336 default y if ARM64 && !TARGET_THUNDERX_88XX 337 help 338 This ARM64 system supports AArch32 execution state. 339 340choice 341 prompt "Target select" 342 default TARGET_HIKEY 343 344config ARCH_AT91 345 bool "Atmel AT91" 346 select SPL_BOARD_INIT if SPL 347 348config TARGET_EDB93XX 349 bool "Support edb93xx" 350 select CPU_ARM920T 351 352config TARGET_ASPENITE 353 bool "Support aspenite" 354 select CPU_ARM926EJS 355 356config TARGET_GPLUGD 357 bool "Support gplugd" 358 select CPU_ARM926EJS 359 360config ARCH_DAVINCI 361 bool "TI DaVinci" 362 select CPU_ARM926EJS 363 imply CMD_SAVES 364 help 365 Support for TI's DaVinci platform. 366 367config KIRKWOOD 368 bool "Marvell Kirkwood" 369 select CPU_ARM926EJS 370 select BOARD_EARLY_INIT_F 371 select ARCH_MISC_INIT 372 373config ARCH_MVEBU 374 bool "Marvell MVEBU family (Armada XP/375/38x/3700/7K/8K)" 375 select OF_CONTROL 376 select OF_SEPARATE 377 select DM 378 select DM_ETH 379 select DM_SERIAL 380 select DM_SPI 381 select DM_SPI_FLASH 382 383config TARGET_DEVKIT3250 384 bool "Support devkit3250" 385 select CPU_ARM926EJS 386 select SUPPORT_SPL 387 388config TARGET_WORK_92105 389 bool "Support work_92105" 390 select CPU_ARM926EJS 391 select SUPPORT_SPL 392 393config TARGET_APF27 394 bool "Support apf27" 395 select CPU_ARM926EJS 396 select SUPPORT_SPL 397 398config TARGET_APX4DEVKIT 399 bool "Support apx4devkit" 400 select CPU_ARM926EJS 401 select SUPPORT_SPL 402 403config TARGET_XFI3 404 bool "Support xfi3" 405 select CPU_ARM926EJS 406 select SUPPORT_SPL 407 408config TARGET_M28EVK 409 bool "Support m28evk" 410 select CPU_ARM926EJS 411 select SUPPORT_SPL 412 413config TARGET_MX23EVK 414 bool "Support mx23evk" 415 select CPU_ARM926EJS 416 select SUPPORT_SPL 417 select BOARD_EARLY_INIT_F 418 419config TARGET_MX28EVK 420 bool "Support mx28evk" 421 select CPU_ARM926EJS 422 select SUPPORT_SPL 423 select BOARD_EARLY_INIT_F 424 425config TARGET_MX23_OLINUXINO 426 bool "Support mx23_olinuxino" 427 select CPU_ARM926EJS 428 select SUPPORT_SPL 429 select BOARD_EARLY_INIT_F 430 431config TARGET_BG0900 432 bool "Support bg0900" 433 select CPU_ARM926EJS 434 select SUPPORT_SPL 435 436config TARGET_SANSA_FUZE_PLUS 437 bool "Support sansa_fuze_plus" 438 select CPU_ARM926EJS 439 select SUPPORT_SPL 440 441config TARGET_SC_SPS_1 442 bool "Support sc_sps_1" 443 select CPU_ARM926EJS 444 select SUPPORT_SPL 445 446config ORION5X 447 bool "Marvell Orion" 448 select CPU_ARM926EJS 449 450config TARGET_SPEAR300 451 bool "Support spear300" 452 select CPU_ARM926EJS 453 select BOARD_EARLY_INIT_F 454 imply CMD_SAVES 455 456config TARGET_SPEAR310 457 bool "Support spear310" 458 select CPU_ARM926EJS 459 select BOARD_EARLY_INIT_F 460 imply CMD_SAVES 461 462config TARGET_SPEAR320 463 bool "Support spear320" 464 select CPU_ARM926EJS 465 select BOARD_EARLY_INIT_F 466 imply CMD_SAVES 467 468config TARGET_SPEAR600 469 bool "Support spear600" 470 select CPU_ARM926EJS 471 select BOARD_EARLY_INIT_F 472 imply CMD_SAVES 473 474config TARGET_STV0991 475 bool "Support stv0991" 476 select CPU_V7 477 select DM 478 select DM_SERIAL 479 select DM_SPI 480 select DM_SPI_FLASH 481 select SPI_FLASH 482 483config TARGET_X600 484 bool "Support x600" 485 select BOARD_LATE_INIT 486 select CPU_ARM926EJS 487 select SUPPORT_SPL 488 489config TARGET_IMX31_PHYCORE 490 bool "Support imx31_phycore_eet" 491 select CPU_ARM1136 492 select BOARD_EARLY_INIT_F 493 494config TARGET_IMX31_PHYCORE_EET 495 bool "Support imx31_phycore_eet" 496 select BOARD_LATE_INIT 497 select CPU_ARM1136 498 select BOARD_EARLY_INIT_F 499 500config TARGET_MX31ADS 501 bool "Support mx31ads" 502 select CPU_ARM1136 503 select BOARD_EARLY_INIT_F 504 505config TARGET_MX31PDK 506 bool "Support mx31pdk" 507 select BOARD_LATE_INIT 508 select CPU_ARM1136 509 select SUPPORT_SPL 510 select BOARD_EARLY_INIT_F 511 512config TARGET_WOODBURN 513 bool "Support woodburn" 514 select CPU_ARM1136 515 516config TARGET_WOODBURN_SD 517 bool "Support woodburn_sd" 518 select CPU_ARM1136 519 select SUPPORT_SPL 520 521config TARGET_FLEA3 522 bool "Support flea3" 523 select CPU_ARM1136 524 525config TARGET_MX35PDK 526 bool "Support mx35pdk" 527 select BOARD_LATE_INIT 528 select CPU_ARM1136 529 530config ARCH_BCM283X 531 bool "Broadcom BCM283X family" 532 select DM 533 select DM_SERIAL 534 select DM_GPIO 535 select OF_CONTROL 536 imply FAT_WRITE 537 538config TARGET_VEXPRESS_CA15_TC2 539 bool "Support vexpress_ca15_tc2" 540 select CPU_V7 541 select CPU_V7_HAS_NONSEC 542 select CPU_V7_HAS_VIRT 543 544config TARGET_VEXPRESS_CA5X2 545 bool "Support vexpress_ca5x2" 546 select CPU_V7 547 548config TARGET_VEXPRESS_CA9X4 549 bool "Support vexpress_ca9x4" 550 select CPU_V7 551 552config TARGET_BCM23550_W1D 553 bool "Support bcm23550_w1d" 554 select CPU_V7 555 imply CRC32_VERIFY 556 imply FAT_WRITE 557 558config TARGET_BCM28155_AP 559 bool "Support bcm28155_ap" 560 select CPU_V7 561 imply CRC32_VERIFY 562 imply FAT_WRITE 563 564config TARGET_BCMCYGNUS 565 bool "Support bcmcygnus" 566 select CPU_V7 567 imply CRC32_VERIFY 568 imply CMD_HASH 569 imply FAT_WRITE 570 imply HASH_VERIFY 571 imply NETDEVICES 572 imply BCM_SF2_ETH 573 imply BCM_SF2_ETH_GMAC 574 575config TARGET_BCMNSP 576 bool "Support bcmnsp" 577 select CPU_V7 578 579config TARGET_BCMNS2 580 bool "Support Broadcom Northstar2" 581 select ARM64 582 help 583 Support for Broadcom Northstar 2 SoCs. NS2 is a quad-core 64-bit 584 ARMv8 Cortex-A57 processors targeting a broad range of networking 585 applications 586 587config ARCH_EXYNOS 588 bool "Samsung EXYNOS" 589 select DM 590 select DM_I2C 591 select DM_SPI_FLASH 592 select DM_SERIAL 593 select DM_SPI 594 select DM_GPIO 595 select DM_KEYBOARD 596 imply FAT_WRITE 597 598config ARCH_S5PC1XX 599 bool "Samsung S5PC1XX" 600 select CPU_V7 601 select DM 602 select DM_SERIAL 603 select DM_GPIO 604 select DM_I2C 605 606config ARCH_HIGHBANK 607 bool "Calxeda Highbank" 608 select CPU_V7 609 610config ARCH_INTEGRATOR 611 bool "ARM Ltd. Integrator family" 612 select DM 613 select DM_SERIAL 614 615config ARCH_KEYSTONE 616 bool "TI Keystone" 617 select CPU_V7 618 select SUPPORT_SPL 619 select SYS_THUMB_BUILD 620 select CMD_POWEROFF 621 imply CMD_MTDPARTS 622 imply FIT 623 imply CMD_SAVES 624 625config ARCH_OMAP2PLUS 626 bool "TI OMAP2+" 627 select CPU_V7 628 select SPL_BOARD_INIT if SPL 629 select SPL_STACK_R if SPL 630 select SUPPORT_SPL 631 imply FIT 632 633config ARCH_MESON 634 bool "Amlogic Meson" 635 help 636 Support for the Meson SoC family developed by Amlogic Inc., 637 targeted at media players and tablet computers. We currently 638 support the S905 (GXBaby) 64-bit SoC. 639 640config ARCH_MX25 641 bool "NXP MX25" 642 select CPU_ARM926EJS 643 644config ARCH_MX7ULP 645 bool "NXP MX7ULP" 646 select CPU_V7 647 select ROM_UNIFIED_SECTIONS 648 649config ARCH_MX7 650 bool "Freescale MX7" 651 select CPU_V7 652 select SYS_FSL_HAS_SEC if SECURE_BOOT 653 select SYS_FSL_SEC_COMPAT_4 654 select SYS_FSL_SEC_LE 655 select BOARD_EARLY_INIT_F 656 select ARCH_MISC_INIT 657 658config ARCH_MX6 659 bool "Freescale MX6" 660 select CPU_V7 661 select SYS_FSL_HAS_SEC if SECURE_BOOT 662 select SYS_FSL_SEC_COMPAT_4 663 select SYS_FSL_SEC_LE 664 select SYS_THUMB_BUILD if SPL 665 666if ARCH_MX6 667config SPL_LDSCRIPT 668 default "arch/arm/mach-omap2/u-boot-spl.lds" 669endif 670 671config ARCH_MX5 672 bool "Freescale MX5" 673 select CPU_V7 674 select BOARD_EARLY_INIT_F 675 676config ARCH_QEMU 677 bool "QEMU Virtual Platform" 678 select CPU_V7 679 select ARCH_SUPPORT_PSCI 680 select DM 681 select DM_SERIAL 682 select OF_CONTROL 683 684config ARCH_RMOBILE 685 bool "Renesas ARM SoCs" 686 select DM 687 select DM_SERIAL 688 select BOARD_EARLY_INIT_F 689 imply FAT_WRITE 690 imply SYS_THUMB_BUILD 691 692config TARGET_S32V234EVB 693 bool "Support s32v234evb" 694 select ARM64 695 select SYS_FSL_ERRATUM_ESDHC111 696 697config ARCH_SNAPDRAGON 698 bool "Qualcomm Snapdragon SoCs" 699 select ARM64 700 select DM 701 select DM_GPIO 702 select DM_SERIAL 703 select SPMI 704 select OF_CONTROL 705 select OF_SEPARATE 706 707config ARCH_SOCFPGA 708 bool "Altera SOCFPGA family" 709 select CPU_V7 710 select SUPPORT_SPL 711 select OF_CONTROL 712 select SPL_OF_CONTROL 713 select DM 714 select DM_SPI_FLASH 715 select DM_SPI 716 select ENABLE_ARM_SOC_BOOT0_HOOK 717 select ARCH_EARLY_INIT_R 718 select ARCH_MISC_INIT 719 select SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION 720 select SYS_THUMB_BUILD 721 imply CMD_MTDPARTS 722 imply CRC32_VERIFY 723 imply FAT_WRITE 724 725config ARCH_SUNXI 726 bool "Support sunxi (Allwinner) SoCs" 727 select BINMAN 728 select CMD_GPIO 729 select CMD_MMC if MMC 730 select CMD_USB if DISTRO_DEFAULTS 731 select DM 732 select DM_ETH 733 select DM_GPIO 734 select DM_KEYBOARD 735 select DM_SERIAL 736 select DM_USB if DISTRO_DEFAULTS 737 select OF_BOARD_SETUP 738 select OF_CONTROL 739 select OF_SEPARATE 740 select SPL_STACK_R if SPL 741 select SPL_SYS_MALLOC_SIMPLE if SPL 742 select SYS_NS16550 743 select SPL_SYS_THUMB_BUILD if !ARM64 744 select SYS_THUMB_BUILD if !ARM64 745 select USB if DISTRO_DEFAULTS 746 select USB_STORAGE if DISTRO_DEFAULTS 747 select USB_KEYBOARD if DISTRO_DEFAULTS 748 select USE_TINY_PRINTF 749 imply CMD_GPT 750 imply FAT_WRITE 751 imply PRE_CONSOLE_BUFFER 752 imply SPL_GPIO_SUPPORT 753 imply SPL_LIBCOMMON_SUPPORT 754 imply SPL_LIBDISK_SUPPORT 755 imply SPL_LIBGENERIC_SUPPORT 756 imply SPL_MMC_SUPPORT if MMC 757 imply SPL_POWER_SUPPORT 758 imply SPL_SERIAL_SUPPORT 759 imply USB_GADGET 760 761config TARGET_TS4600 762 bool "Support TS4600" 763 select CPU_ARM926EJS 764 select SUPPORT_SPL 765 766config ARCH_VF610 767 bool "Freescale Vybrid" 768 select CPU_V7 769 select SYS_FSL_ERRATUM_ESDHC111 770 imply CMD_MTDPARTS 771 imply NAND 772 773config ARCH_ZYNQ 774 bool "Xilinx Zynq based platform" 775 select BOARD_LATE_INIT 776 select CPU_V7 777 select SUPPORT_SPL 778 select OF_CONTROL 779 select SPL_BOARD_INIT if SPL 780 select SPL_OF_CONTROL if SPL 781 select DM 782 select DM_ETH 783 select DM_GPIO 784 select SPL_DM if SPL 785 select DM_MMC 786 select DM_SPI 787 select DM_SERIAL 788 select DM_SPI_FLASH 789 select SPL_SEPARATE_BSS if SPL 790 select DM_USB if USB 791 select BLK 792 select CLK 793 select SPL_CLK 794 select CLK_ZYNQ 795 imply CMD_CLK 796 imply FAT_WRITE 797 imply CMD_SPL 798 799config ARCH_ZYNQMP 800 bool "Xilinx ZynqMP based platform" 801 select ARM64 802 select BOARD_LATE_INIT 803 select DM 804 select OF_CONTROL 805 select DM_SERIAL 806 select SUPPORT_SPL 807 select CLK 808 select SPL_BOARD_INIT if SPL 809 select SPL_CLK if SPL 810 select DM_USB if USB 811 imply FAT_WRITE 812 813config TEGRA 814 bool "NVIDIA Tegra" 815 imply FAT_WRITE 816 817config TARGET_VEXPRESS64_AEMV8A 818 bool "Support vexpress_aemv8a" 819 select ARM64 820 821config TARGET_VEXPRESS64_BASE_FVP 822 bool "Support Versatile Express ARMv8a FVP BASE model" 823 select ARM64 824 select SEMIHOSTING 825 826config TARGET_VEXPRESS64_BASE_FVP_DRAM 827 bool "Support Versatile Express ARMv8a FVP BASE model booting from DRAM" 828 select ARM64 829 help 830 This target is derived from TARGET_VEXPRESS64_BASE_FVP and over-rides 831 the default config to allow the user to load the images directly into 832 DRAM using model parameters rather than by using semi-hosting to load 833 the files from the host filesystem. 834 835config TARGET_VEXPRESS64_JUNO 836 bool "Support Versatile Express Juno Development Platform" 837 select ARM64 838 839config TARGET_LS2080A_EMU 840 bool "Support ls2080a_emu" 841 select ARCH_LS2080A 842 select ARM64 843 select ARMV8_MULTIENTRY 844 select ARCH_MISC_INIT 845 help 846 Support for Freescale LS2080A_EMU platform 847 The LS2080A Development System (EMULATOR) is a pre silicon 848 development platform that supports the QorIQ LS2080A 849 Layerscape Architecture processor. 850 851config TARGET_LS2080A_SIMU 852 bool "Support ls2080a_simu" 853 select ARCH_LS2080A 854 select ARM64 855 select ARMV8_MULTIENTRY 856 select ARCH_MISC_INIT 857 help 858 Support for Freescale LS2080A_SIMU platform 859 The LS2080A Development System (QDS) is a pre silicon 860 development platform that supports the QorIQ LS2080A 861 Layerscape Architecture processor. 862 863config TARGET_LS1088AQDS 864 bool "Support ls1088aqds" 865 select ARCH_LS1088A 866 select ARM64 867 select ARMV8_MULTIENTRY 868 select ARCH_MISC_INIT 869 select BOARD_LATE_INIT 870 select SUPPORT_SPL 871 help 872 Support for NXP LS1088AQDS platform 873 The LS1088A Development System (QDS) is a high-performance 874 development platform that supports the QorIQ LS1088A 875 Layerscape Architecture processor. 876 877config TARGET_LS2080AQDS 878 bool "Support ls2080aqds" 879 select ARCH_LS2080A 880 select ARM64 881 select ARMV8_MULTIENTRY 882 select BOARD_LATE_INIT 883 select SUPPORT_SPL 884 select ARCH_MISC_INIT 885 imply SCSI 886 imply SCSI_AHCI 887 help 888 Support for Freescale LS2080AQDS platform 889 The LS2080A Development System (QDS) is a high-performance 890 development platform that supports the QorIQ LS2080A 891 Layerscape Architecture processor. 892 893config TARGET_LS2080ARDB 894 bool "Support ls2080ardb" 895 select ARCH_LS2080A 896 select ARM64 897 select ARMV8_MULTIENTRY 898 select BOARD_LATE_INIT 899 select SUPPORT_SPL 900 select ARCH_MISC_INIT 901 imply SCSI 902 imply SCSI_AHCI 903 help 904 Support for Freescale LS2080ARDB platform. 905 The LS2080A Reference design board (RDB) is a high-performance 906 development platform that supports the QorIQ LS2080A 907 Layerscape Architecture processor. 908 909config TARGET_LS2081ARDB 910 bool "Support ls2081ardb" 911 select ARCH_LS2080A 912 select ARM64 913 select ARMV8_MULTIENTRY 914 select BOARD_LATE_INIT 915 select SUPPORT_SPL 916 select ARCH_MISC_INIT 917 help 918 Support for Freescale LS2081ARDB platform. 919 The LS2081A Reference design board (RDB) is a high-performance 920 development platform that supports the QorIQ LS2081A/LS2041A 921 Layerscape Architecture processor. 922 923config TARGET_HIKEY 924 bool "Support HiKey 96boards Consumer Edition Platform" 925 select ARM64 926 select DM 927 select DM_GPIO 928 select DM_SERIAL 929 select OF_CONTROL 930 help 931 Support for HiKey 96boards platform. It features a HI6220 932 SoC, with 8xA53 CPU, mali450 gpu, and 1GB RAM. 933 934config TARGET_POPLAR 935 bool "Support Poplar 96boards Enterprise Edition Platform" 936 select ARM64 937 select DM 938 select OF_CONTROL 939 select DM_SERIAL 940 select DM_USB 941 help 942 Support for Poplar 96boards EE platform. It features a HI3798cv200 943 SoC, with 4xA53 CPU, 1GB RAM and the high performance Mali T720 GPU 944 making it capable of running any commercial set-top solution based on 945 Linux or Android. 946 947config TARGET_LS1012AQDS 948 bool "Support ls1012aqds" 949 select ARCH_LS1012A 950 select ARM64 951 select BOARD_LATE_INIT 952 help 953 Support for Freescale LS1012AQDS platform. 954 The LS1012A Development System (QDS) is a high-performance 955 development platform that supports the QorIQ LS1012A 956 Layerscape Architecture processor. 957 958config TARGET_LS1012ARDB 959 bool "Support ls1012ardb" 960 select ARCH_LS1012A 961 select ARM64 962 select BOARD_LATE_INIT 963 imply SCSI 964 imply SCSI_AHCI 965 help 966 Support for Freescale LS1012ARDB platform. 967 The LS1012A Reference design board (RDB) is a high-performance 968 development platform that supports the QorIQ LS1012A 969 Layerscape Architecture processor. 970 971config TARGET_LS1012AFRDM 972 bool "Support ls1012afrdm" 973 select ARCH_LS1012A 974 select ARM64 975 help 976 Support for Freescale LS1012AFRDM platform. 977 The LS1012A Freedom board (FRDM) is a high-performance 978 development platform that supports the QorIQ LS1012A 979 Layerscape Architecture processor. 980 981config TARGET_LS1088ARDB 982 bool "Support ls1088ardb" 983 select ARCH_LS1088A 984 select ARM64 985 select ARMV8_MULTIENTRY 986 select ARCH_MISC_INIT 987 select BOARD_LATE_INIT 988 select SUPPORT_SPL 989 help 990 Support for NXP LS1088ARDB platform. 991 The LS1088A Reference design board (RDB) is a high-performance 992 development platform that supports the QorIQ LS1088A 993 Layerscape Architecture processor. 994 995config TARGET_LS1021AQDS 996 bool "Support ls1021aqds" 997 select BOARD_LATE_INIT 998 select CPU_V7 999 select CPU_V7_HAS_NONSEC 1000 select CPU_V7_HAS_VIRT 1001 select SUPPORT_SPL 1002 select ARCH_LS1021A 1003 select ARCH_SUPPORT_PSCI 1004 select LS1_DEEP_SLEEP 1005 select SYS_FSL_DDR 1006 select BOARD_EARLY_INIT_F 1007 imply SCSI 1008 1009config TARGET_LS1021ATWR 1010 bool "Support ls1021atwr" 1011 select BOARD_LATE_INIT 1012 select CPU_V7 1013 select CPU_V7_HAS_NONSEC 1014 select CPU_V7_HAS_VIRT 1015 select SUPPORT_SPL 1016 select ARCH_LS1021A 1017 select ARCH_SUPPORT_PSCI 1018 select LS1_DEEP_SLEEP 1019 select BOARD_EARLY_INIT_F 1020 imply SCSI 1021 1022config TARGET_LS1021AIOT 1023 bool "Support ls1021aiot" 1024 select BOARD_LATE_INIT 1025 select CPU_V7 1026 select CPU_V7_HAS_NONSEC 1027 select CPU_V7_HAS_VIRT 1028 select SUPPORT_SPL 1029 select ARCH_LS1021A 1030 select ARCH_SUPPORT_PSCI 1031 imply SCSI 1032 help 1033 Support for Freescale LS1021AIOT platform. 1034 The LS1021A Freescale board (IOT) is a high-performance 1035 development platform that supports the QorIQ LS1021A 1036 Layerscape Architecture processor. 1037 1038config TARGET_LS1043AQDS 1039 bool "Support ls1043aqds" 1040 select ARCH_LS1043A 1041 select ARM64 1042 select ARMV8_MULTIENTRY 1043 select BOARD_LATE_INIT 1044 select SUPPORT_SPL 1045 select BOARD_EARLY_INIT_F 1046 imply SCSI 1047 help 1048 Support for Freescale LS1043AQDS platform. 1049 1050config TARGET_LS1043ARDB 1051 bool "Support ls1043ardb" 1052 select ARCH_LS1043A 1053 select ARM64 1054 select ARMV8_MULTIENTRY 1055 select BOARD_LATE_INIT 1056 select SUPPORT_SPL 1057 select BOARD_EARLY_INIT_F 1058 imply SCSI 1059 help 1060 Support for Freescale LS1043ARDB platform. 1061 1062config TARGET_LS1046AQDS 1063 bool "Support ls1046aqds" 1064 select ARCH_LS1046A 1065 select ARM64 1066 select ARMV8_MULTIENTRY 1067 select BOARD_LATE_INIT 1068 select SUPPORT_SPL 1069 select DM_SPI_FLASH if DM_SPI 1070 select BOARD_EARLY_INIT_F 1071 imply SCSI 1072 help 1073 Support for Freescale LS1046AQDS platform. 1074 The LS1046A Development System (QDS) is a high-performance 1075 development platform that supports the QorIQ LS1046A 1076 Layerscape Architecture processor. 1077 1078config TARGET_LS1046ARDB 1079 bool "Support ls1046ardb" 1080 select ARCH_LS1046A 1081 select ARM64 1082 select ARMV8_MULTIENTRY 1083 select BOARD_LATE_INIT 1084 select SUPPORT_SPL 1085 select DM_SPI_FLASH if DM_SPI 1086 select POWER_MC34VR500 1087 select BOARD_EARLY_INIT_F 1088 imply SCSI 1089 help 1090 Support for Freescale LS1046ARDB platform. 1091 The LS1046A Reference Design Board (RDB) is a high-performance 1092 development platform that supports the QorIQ LS1046A 1093 Layerscape Architecture processor. 1094 1095config TARGET_H2200 1096 bool "Support h2200" 1097 select CPU_PXA 1098 1099config TARGET_ZIPITZ2 1100 bool "Support zipitz2" 1101 select CPU_PXA 1102 1103config TARGET_COLIBRI_PXA270 1104 bool "Support colibri_pxa270" 1105 select CPU_PXA 1106 1107config ARCH_UNIPHIER 1108 bool "Socionext UniPhier SoCs" 1109 select BOARD_LATE_INIT 1110 select DM 1111 select DM_GPIO 1112 select DM_I2C 1113 select DM_MMC 1114 select DM_RESET 1115 select DM_SERIAL 1116 select DM_USB 1117 select OF_CONTROL 1118 select OF_LIBFDT 1119 select PINCTRL 1120 select SPL_BOARD_INIT if SPL 1121 select SPL_DM if SPL 1122 select SPL_LIBCOMMON_SUPPORT if SPL 1123 select SPL_LIBGENERIC_SUPPORT if SPL 1124 select SPL_OF_CONTROL if SPL 1125 select SPL_PINCTRL if SPL 1126 select SUPPORT_SPL 1127 imply FAT_WRITE 1128 help 1129 Support for UniPhier SoC family developed by Socionext Inc. 1130 (formerly, System LSI Business Division of Panasonic Corporation) 1131 1132config STM32 1133 bool "Support STM32" 1134 select CPU_V7M 1135 select DM 1136 select DM_SERIAL 1137 select SYS_THUMB_BUILD 1138 1139config ARCH_STI 1140 bool "Support STMicrolectronics SoCs" 1141 select CPU_V7 1142 select DM 1143 select DM_SERIAL 1144 select BLK 1145 select DM_MMC 1146 select DM_RESET 1147 help 1148 Support for STMicroelectronics STiH407/10 SoC family. 1149 This SoC is used on Linaro 96Board STiH410-B2260 1150 1151config ARCH_ROCKCHIP 1152 bool "Support Rockchip SoCs" 1153 select OF_CONTROL 1154 select BLK 1155 select DM 1156 select SPL_DM if SPL 1157 select SYS_MALLOC_F 1158 select SYS_THUMB_BUILD if !ARM64 1159 select SPL_SYS_MALLOC_SIMPLE if SPL 1160 select DM_GPIO 1161 select DM_I2C 1162 select DM_MMC 1163 select DM_SERIAL 1164 select DM_SPI 1165 select DM_SPI_FLASH 1166 select DM_USB if USB 1167 select DM_PWM 1168 select DM_REGULATOR 1169 select ENABLE_ARM_SOC_BOOT0_HOOK 1170 imply CMD_FASTBOOT 1171 imply FASTBOOT 1172 imply FAT_WRITE 1173 imply USB_FUNCTION_FASTBOOT 1174 imply SPL_SYSRESET 1175 imply TPL_SYSRESET 1176 imply ADC 1177 imply SARADC_ROCKCHIP 1178 1179config TARGET_THUNDERX_88XX 1180 bool "Support ThunderX 88xx" 1181 select ARM64 1182 select OF_CONTROL 1183 select SYS_CACHE_SHIFT_7 1184 1185config ARCH_ASPEED 1186 bool "Support Aspeed SoCs" 1187 select OF_CONTROL 1188 select DM 1189 1190endchoice 1191 1192source "arch/arm/mach-aspeed/Kconfig" 1193 1194source "arch/arm/mach-at91/Kconfig" 1195 1196source "arch/arm/mach-bcm283x/Kconfig" 1197 1198source "arch/arm/mach-davinci/Kconfig" 1199 1200source "arch/arm/mach-exynos/Kconfig" 1201 1202source "arch/arm/mach-highbank/Kconfig" 1203 1204source "arch/arm/mach-integrator/Kconfig" 1205 1206source "arch/arm/mach-keystone/Kconfig" 1207 1208source "arch/arm/mach-kirkwood/Kconfig" 1209 1210source "arch/arm/mach-mvebu/Kconfig" 1211 1212source "arch/arm/cpu/armv7/ls102xa/Kconfig" 1213 1214source "arch/arm/mach-imx/mx2/Kconfig" 1215 1216source "arch/arm/mach-imx/mx7ulp/Kconfig" 1217 1218source "arch/arm/mach-imx/mx7/Kconfig" 1219 1220source "arch/arm/mach-imx/mx6/Kconfig" 1221 1222source "arch/arm/mach-imx/mx5/Kconfig" 1223 1224source "arch/arm/mach-omap2/Kconfig" 1225 1226source "arch/arm/cpu/armv8/fsl-layerscape/Kconfig" 1227 1228source "arch/arm/mach-orion5x/Kconfig" 1229 1230source "arch/arm/mach-rmobile/Kconfig" 1231 1232source "arch/arm/mach-meson/Kconfig" 1233 1234source "arch/arm/mach-qemu/Kconfig" 1235 1236source "arch/arm/mach-rockchip/Kconfig" 1237 1238source "arch/arm/mach-s5pc1xx/Kconfig" 1239 1240source "arch/arm/mach-snapdragon/Kconfig" 1241 1242source "arch/arm/mach-socfpga/Kconfig" 1243 1244source "arch/arm/mach-sti/Kconfig" 1245 1246source "arch/arm/mach-stm32/Kconfig" 1247 1248source "arch/arm/mach-sunxi/Kconfig" 1249 1250source "arch/arm/mach-tegra/Kconfig" 1251 1252source "arch/arm/mach-uniphier/Kconfig" 1253 1254source "arch/arm/cpu/armv7/vf610/Kconfig" 1255 1256source "arch/arm/mach-zynq/Kconfig" 1257 1258source "arch/arm/cpu/armv7/Kconfig" 1259 1260source "arch/arm/cpu/armv8/zynqmp/Kconfig" 1261 1262source "arch/arm/cpu/armv8/Kconfig" 1263 1264source "arch/arm/mach-imx/Kconfig" 1265 1266source "board/aries/m28evk/Kconfig" 1267source "board/bosch/shc/Kconfig" 1268source "board/CarMediaLab/flea3/Kconfig" 1269source "board/Marvell/aspenite/Kconfig" 1270source "board/Marvell/gplugd/Kconfig" 1271source "board/armadeus/apf27/Kconfig" 1272source "board/armltd/vexpress/Kconfig" 1273source "board/armltd/vexpress64/Kconfig" 1274source "board/bluegiga/apx4devkit/Kconfig" 1275source "board/broadcom/bcm23550_w1d/Kconfig" 1276source "board/broadcom/bcm28155_ap/Kconfig" 1277source "board/broadcom/bcmcygnus/Kconfig" 1278source "board/broadcom/bcmnsp/Kconfig" 1279source "board/broadcom/bcmns2/Kconfig" 1280source "board/cavium/thunderx/Kconfig" 1281source "board/cirrus/edb93xx/Kconfig" 1282source "board/creative/xfi3/Kconfig" 1283source "board/freescale/ls2080a/Kconfig" 1284source "board/freescale/ls2080aqds/Kconfig" 1285source "board/freescale/ls2080ardb/Kconfig" 1286source "board/freescale/ls1088a/Kconfig" 1287source "board/freescale/ls1021aqds/Kconfig" 1288source "board/freescale/ls1043aqds/Kconfig" 1289source "board/freescale/ls1021atwr/Kconfig" 1290source "board/freescale/ls1021aiot/Kconfig" 1291source "board/freescale/ls1046aqds/Kconfig" 1292source "board/freescale/ls1043ardb/Kconfig" 1293source "board/freescale/ls1046ardb/Kconfig" 1294source "board/freescale/ls1012aqds/Kconfig" 1295source "board/freescale/ls1012ardb/Kconfig" 1296source "board/freescale/ls1012afrdm/Kconfig" 1297source "board/freescale/mx23evk/Kconfig" 1298source "board/freescale/mx28evk/Kconfig" 1299source "board/freescale/mx31ads/Kconfig" 1300source "board/freescale/mx31pdk/Kconfig" 1301source "board/freescale/mx35pdk/Kconfig" 1302source "board/freescale/s32v234evb/Kconfig" 1303source "board/gdsys/a38x/Kconfig" 1304source "board/grinn/chiliboard/Kconfig" 1305source "board/gumstix/pepper/Kconfig" 1306source "board/h2200/Kconfig" 1307source "board/hisilicon/hikey/Kconfig" 1308source "board/hisilicon/poplar/Kconfig" 1309source "board/imx31_phycore/Kconfig" 1310source "board/isee/igep003x/Kconfig" 1311source "board/olimex/mx23_olinuxino/Kconfig" 1312source "board/phytec/pcm051/Kconfig" 1313source "board/ppcag/bg0900/Kconfig" 1314source "board/sandisk/sansa_fuze_plus/Kconfig" 1315source "board/schulercontrol/sc_sps_1/Kconfig" 1316source "board/silica/pengwyn/Kconfig" 1317source "board/spear/spear300/Kconfig" 1318source "board/spear/spear310/Kconfig" 1319source "board/spear/spear320/Kconfig" 1320source "board/spear/spear600/Kconfig" 1321source "board/spear/x600/Kconfig" 1322source "board/st/stv0991/Kconfig" 1323source "board/tcl/sl50/Kconfig" 1324source "board/birdland/bav335x/Kconfig" 1325source "board/timll/devkit3250/Kconfig" 1326source "board/toradex/colibri_pxa270/Kconfig" 1327source "board/technologic/ts4600/Kconfig" 1328source "board/vscom/baltos/Kconfig" 1329source "board/woodburn/Kconfig" 1330source "board/work-microwave/work_92105/Kconfig" 1331source "board/zipitz2/Kconfig" 1332 1333source "arch/arm/Kconfig.debug" 1334 1335endmenu 1336 1337config SPL_LDSCRIPT 1338 default "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" if TARGET_APX4DEVKIT || TARGET_BG0900 || TARGET_M28EVK || TARGET_MX23_OLINUXINO || TARGET_MX23EVK || TARGET_MX28EVK || TARGET_SANSA_FUZE_PLUS || TARGET_SC_SPS_1 || TARGET_TS4600 || TARGET_XFI3 1339 default "arch/arm/cpu/arm1136/u-boot-spl.lds" if CPU_ARM1136 1340 default "arch/arm/cpu/armv8/u-boot-spl.lds" if ARM64 1341 1342 1343