1 /* 2 * SD Memory Card emulation as defined in the "SD Memory Card Physical 3 * layer specification, Version 2.00." 4 * 5 * Copyright (c) 2006 Andrzej Zaborowski <balrog@zabor.org> 6 * Copyright (c) 2007 CodeSourcery 7 * Copyright (c) 2018 Philippe Mathieu-Daudé <f4bug@amsat.org> 8 * 9 * Redistribution and use in source and binary forms, with or without 10 * modification, are permitted provided that the following conditions 11 * are met: 12 * 13 * 1. Redistributions of source code must retain the above copyright 14 * notice, this list of conditions and the following disclaimer. 15 * 2. Redistributions in binary form must reproduce the above copyright 16 * notice, this list of conditions and the following disclaimer in 17 * the documentation and/or other materials provided with the 18 * distribution. 19 * 20 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' 21 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, 22 * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A 23 * PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR 24 * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, 25 * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, 26 * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR 27 * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY 28 * OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 29 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE 30 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 31 */ 32 33 #include "qemu/osdep.h" 34 #include "qemu/units.h" 35 #include "hw/irq.h" 36 #include "hw/registerfields.h" 37 #include "sysemu/block-backend.h" 38 #include "hw/sd/sd.h" 39 #include "migration/vmstate.h" 40 #include "qapi/error.h" 41 #include "qemu/bitmap.h" 42 #include "hw/qdev-properties.h" 43 #include "qemu/error-report.h" 44 #include "qemu/timer.h" 45 #include "qemu/log.h" 46 #include "qemu/module.h" 47 #include "sdmmc-internal.h" 48 #include "trace.h" 49 50 //#define DEBUG_SD 1 51 52 typedef enum { 53 sd_r0 = 0, /* no response */ 54 sd_r1, /* normal response command */ 55 sd_r2_i, /* CID register */ 56 sd_r2_s, /* CSD register */ 57 sd_r3, /* OCR register */ 58 sd_r6 = 6, /* Published RCA response */ 59 sd_r7, /* Operating voltage */ 60 sd_r1b = -1, 61 sd_illegal = -2, 62 } sd_rsp_type_t; 63 64 enum SDCardModes { 65 sd_inactive, 66 sd_card_identification_mode, 67 sd_data_transfer_mode, 68 }; 69 70 enum SDCardStates { 71 sd_inactive_state = -1, 72 sd_idle_state = 0, 73 sd_ready_state, 74 sd_identification_state, 75 sd_standby_state, 76 sd_transfer_state, 77 sd_sendingdata_state, 78 sd_receivingdata_state, 79 sd_programming_state, 80 sd_disconnect_state, 81 }; 82 83 struct SDState { 84 DeviceState parent_obj; 85 86 /* SD Memory Card Registers */ 87 uint32_t ocr; 88 uint8_t scr[8]; 89 uint8_t cid[16]; 90 uint8_t csd[16]; 91 uint16_t rca; 92 uint32_t card_status; 93 uint8_t sd_status[64]; 94 95 /* Configurable properties */ 96 uint8_t spec_version; 97 BlockBackend *blk; 98 bool spi; 99 100 uint32_t mode; /* current card mode, one of SDCardModes */ 101 int32_t state; /* current card state, one of SDCardStates */ 102 uint32_t vhs; 103 bool wp_switch; 104 unsigned long *wp_groups; 105 int32_t wpgrps_size; 106 uint64_t size; 107 uint32_t blk_len; 108 uint32_t multi_blk_cnt; 109 uint32_t erase_start; 110 uint32_t erase_end; 111 uint8_t pwd[16]; 112 uint32_t pwd_len; 113 uint8_t function_group[6]; 114 uint8_t current_cmd; 115 /* True if we will handle the next command as an ACMD. Note that this does 116 * *not* track the APP_CMD status bit! 117 */ 118 bool expecting_acmd; 119 uint32_t blk_written; 120 uint64_t data_start; 121 uint32_t data_offset; 122 uint8_t data[512]; 123 qemu_irq readonly_cb; 124 qemu_irq inserted_cb; 125 QEMUTimer *ocr_power_timer; 126 const char *proto_name; 127 bool enable; 128 uint8_t dat_lines; 129 bool cmd_line; 130 }; 131 132 static const char *sd_state_name(enum SDCardStates state) 133 { 134 static const char *state_name[] = { 135 [sd_idle_state] = "idle", 136 [sd_ready_state] = "ready", 137 [sd_identification_state] = "identification", 138 [sd_standby_state] = "standby", 139 [sd_transfer_state] = "transfer", 140 [sd_sendingdata_state] = "sendingdata", 141 [sd_receivingdata_state] = "receivingdata", 142 [sd_programming_state] = "programming", 143 [sd_disconnect_state] = "disconnect", 144 }; 145 if (state == sd_inactive_state) { 146 return "inactive"; 147 } 148 assert(state < ARRAY_SIZE(state_name)); 149 return state_name[state]; 150 } 151 152 static const char *sd_response_name(sd_rsp_type_t rsp) 153 { 154 static const char *response_name[] = { 155 [sd_r0] = "RESP#0 (no response)", 156 [sd_r1] = "RESP#1 (normal cmd)", 157 [sd_r2_i] = "RESP#2 (CID reg)", 158 [sd_r2_s] = "RESP#2 (CSD reg)", 159 [sd_r3] = "RESP#3 (OCR reg)", 160 [sd_r6] = "RESP#6 (RCA)", 161 [sd_r7] = "RESP#7 (operating voltage)", 162 }; 163 if (rsp == sd_illegal) { 164 return "ILLEGAL RESP"; 165 } 166 if (rsp == sd_r1b) { 167 rsp = sd_r1; 168 } 169 assert(rsp < ARRAY_SIZE(response_name)); 170 return response_name[rsp]; 171 } 172 173 static uint8_t sd_get_dat_lines(SDState *sd) 174 { 175 return sd->enable ? sd->dat_lines : 0; 176 } 177 178 static bool sd_get_cmd_line(SDState *sd) 179 { 180 return sd->enable ? sd->cmd_line : false; 181 } 182 183 static void sd_set_voltage(SDState *sd, uint16_t millivolts) 184 { 185 trace_sdcard_set_voltage(millivolts); 186 187 switch (millivolts) { 188 case 3001 ... 3600: /* SD_VOLTAGE_3_3V */ 189 case 2001 ... 3000: /* SD_VOLTAGE_3_0V */ 190 break; 191 default: 192 qemu_log_mask(LOG_GUEST_ERROR, "SD card voltage not supported: %.3fV", 193 millivolts / 1000.f); 194 } 195 } 196 197 static void sd_set_mode(SDState *sd) 198 { 199 switch (sd->state) { 200 case sd_inactive_state: 201 sd->mode = sd_inactive; 202 break; 203 204 case sd_idle_state: 205 case sd_ready_state: 206 case sd_identification_state: 207 sd->mode = sd_card_identification_mode; 208 break; 209 210 case sd_standby_state: 211 case sd_transfer_state: 212 case sd_sendingdata_state: 213 case sd_receivingdata_state: 214 case sd_programming_state: 215 case sd_disconnect_state: 216 sd->mode = sd_data_transfer_mode; 217 break; 218 } 219 } 220 221 static const sd_cmd_type_t sd_cmd_type[SDMMC_CMD_MAX] = { 222 sd_bc, sd_none, sd_bcr, sd_bcr, sd_none, sd_none, sd_none, sd_ac, 223 sd_bcr, sd_ac, sd_ac, sd_adtc, sd_ac, sd_ac, sd_none, sd_ac, 224 /* 16 */ 225 sd_ac, sd_adtc, sd_adtc, sd_none, sd_none, sd_none, sd_none, sd_none, 226 sd_adtc, sd_adtc, sd_adtc, sd_adtc, sd_ac, sd_ac, sd_adtc, sd_none, 227 /* 32 */ 228 sd_ac, sd_ac, sd_none, sd_none, sd_none, sd_none, sd_ac, sd_none, 229 sd_none, sd_none, sd_bc, sd_none, sd_none, sd_none, sd_none, sd_none, 230 /* 48 */ 231 sd_none, sd_none, sd_none, sd_none, sd_none, sd_none, sd_none, sd_ac, 232 sd_adtc, sd_none, sd_none, sd_none, sd_none, sd_none, sd_none, sd_none, 233 }; 234 235 static const int sd_cmd_class[SDMMC_CMD_MAX] = { 236 0, 0, 0, 0, 0, 9, 10, 0, 0, 0, 0, 1, 0, 0, 0, 0, 237 2, 2, 2, 2, 3, 3, 3, 3, 4, 4, 4, 4, 6, 6, 6, 6, 238 5, 5, 10, 10, 10, 10, 5, 9, 9, 9, 7, 7, 7, 7, 7, 7, 239 7, 7, 10, 7, 9, 9, 9, 8, 8, 10, 8, 8, 8, 8, 8, 8, 240 }; 241 242 static uint8_t sd_crc7(void *message, size_t width) 243 { 244 int i, bit; 245 uint8_t shift_reg = 0x00; 246 uint8_t *msg = (uint8_t *) message; 247 248 for (i = 0; i < width; i ++, msg ++) 249 for (bit = 7; bit >= 0; bit --) { 250 shift_reg <<= 1; 251 if ((shift_reg >> 7) ^ ((*msg >> bit) & 1)) 252 shift_reg ^= 0x89; 253 } 254 255 return shift_reg; 256 } 257 258 static uint16_t sd_crc16(void *message, size_t width) 259 { 260 int i, bit; 261 uint16_t shift_reg = 0x0000; 262 uint16_t *msg = (uint16_t *) message; 263 width <<= 1; 264 265 for (i = 0; i < width; i ++, msg ++) 266 for (bit = 15; bit >= 0; bit --) { 267 shift_reg <<= 1; 268 if ((shift_reg >> 15) ^ ((*msg >> bit) & 1)) 269 shift_reg ^= 0x1011; 270 } 271 272 return shift_reg; 273 } 274 275 #define OCR_POWER_DELAY_NS 500000 /* 0.5ms */ 276 277 FIELD(OCR, VDD_VOLTAGE_WINDOW, 0, 24) 278 FIELD(OCR, VDD_VOLTAGE_WIN_LO, 0, 8) 279 FIELD(OCR, DUAL_VOLTAGE_CARD, 7, 1) 280 FIELD(OCR, VDD_VOLTAGE_WIN_HI, 8, 16) 281 FIELD(OCR, ACCEPT_SWITCH_1V8, 24, 1) /* Only UHS-I */ 282 FIELD(OCR, UHS_II_CARD, 29, 1) /* Only UHS-II */ 283 FIELD(OCR, CARD_CAPACITY, 30, 1) /* 0:SDSC, 1:SDHC/SDXC */ 284 FIELD(OCR, CARD_POWER_UP, 31, 1) 285 286 #define ACMD41_ENQUIRY_MASK 0x00ffffff 287 #define ACMD41_R3_MASK (R_OCR_VDD_VOLTAGE_WIN_HI_MASK \ 288 | R_OCR_ACCEPT_SWITCH_1V8_MASK \ 289 | R_OCR_UHS_II_CARD_MASK \ 290 | R_OCR_CARD_CAPACITY_MASK \ 291 | R_OCR_CARD_POWER_UP_MASK) 292 293 static void sd_set_ocr(SDState *sd) 294 { 295 /* All voltages OK */ 296 sd->ocr = R_OCR_VDD_VOLTAGE_WIN_HI_MASK; 297 } 298 299 static void sd_ocr_powerup(void *opaque) 300 { 301 SDState *sd = opaque; 302 303 trace_sdcard_powerup(); 304 assert(!FIELD_EX32(sd->ocr, OCR, CARD_POWER_UP)); 305 306 /* card power-up OK */ 307 sd->ocr = FIELD_DP32(sd->ocr, OCR, CARD_POWER_UP, 1); 308 309 if (sd->size > 1 * GiB) { 310 sd->ocr = FIELD_DP32(sd->ocr, OCR, CARD_CAPACITY, 1); 311 } 312 } 313 314 static void sd_set_scr(SDState *sd) 315 { 316 sd->scr[0] = 0 << 4; /* SCR structure version 1.0 */ 317 if (sd->spec_version == SD_PHY_SPECv1_10_VERS) { 318 sd->scr[0] |= 1; /* Spec Version 1.10 */ 319 } else { 320 sd->scr[0] |= 2; /* Spec Version 2.00 or Version 3.0X */ 321 } 322 sd->scr[1] = (2 << 4) /* SDSC Card (Security Version 1.01) */ 323 | 0b0101; /* 1-bit or 4-bit width bus modes */ 324 sd->scr[2] = 0x00; /* Extended Security is not supported. */ 325 if (sd->spec_version >= SD_PHY_SPECv3_01_VERS) { 326 sd->scr[2] |= 1 << 7; /* Spec Version 3.0X */ 327 } 328 sd->scr[3] = 0x00; 329 /* reserved for manufacturer usage */ 330 sd->scr[4] = 0x00; 331 sd->scr[5] = 0x00; 332 sd->scr[6] = 0x00; 333 sd->scr[7] = 0x00; 334 } 335 336 #define MID 0xaa 337 #define OID "XY" 338 #define PNM "QEMU!" 339 #define PRV 0x01 340 #define MDT_YR 2006 341 #define MDT_MON 2 342 343 static void sd_set_cid(SDState *sd) 344 { 345 sd->cid[0] = MID; /* Fake card manufacturer ID (MID) */ 346 sd->cid[1] = OID[0]; /* OEM/Application ID (OID) */ 347 sd->cid[2] = OID[1]; 348 sd->cid[3] = PNM[0]; /* Fake product name (PNM) */ 349 sd->cid[4] = PNM[1]; 350 sd->cid[5] = PNM[2]; 351 sd->cid[6] = PNM[3]; 352 sd->cid[7] = PNM[4]; 353 sd->cid[8] = PRV; /* Fake product revision (PRV) */ 354 sd->cid[9] = 0xde; /* Fake serial number (PSN) */ 355 sd->cid[10] = 0xad; 356 sd->cid[11] = 0xbe; 357 sd->cid[12] = 0xef; 358 sd->cid[13] = 0x00 | /* Manufacture date (MDT) */ 359 ((MDT_YR - 2000) / 10); 360 sd->cid[14] = ((MDT_YR % 10) << 4) | MDT_MON; 361 sd->cid[15] = (sd_crc7(sd->cid, 15) << 1) | 1; 362 } 363 364 #define HWBLOCK_SHIFT 9 /* 512 bytes */ 365 #define SECTOR_SHIFT 5 /* 16 kilobytes */ 366 #define WPGROUP_SHIFT 7 /* 2 megs */ 367 #define CMULT_SHIFT 9 /* 512 times HWBLOCK_SIZE */ 368 #define WPGROUP_SIZE (1 << (HWBLOCK_SHIFT + SECTOR_SHIFT + WPGROUP_SHIFT)) 369 370 static const uint8_t sd_csd_rw_mask[16] = { 371 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 372 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xfc, 0xfe, 373 }; 374 375 static void sd_set_csd(SDState *sd, uint64_t size) 376 { 377 uint32_t csize = (size >> (CMULT_SHIFT + HWBLOCK_SHIFT)) - 1; 378 uint32_t sectsize = (1 << (SECTOR_SHIFT + 1)) - 1; 379 uint32_t wpsize = (1 << (WPGROUP_SHIFT + 1)) - 1; 380 381 if (size <= 1 * GiB) { /* Standard Capacity SD */ 382 sd->csd[0] = 0x00; /* CSD structure */ 383 sd->csd[1] = 0x26; /* Data read access-time-1 */ 384 sd->csd[2] = 0x00; /* Data read access-time-2 */ 385 sd->csd[3] = 0x32; /* Max. data transfer rate: 25 MHz */ 386 sd->csd[4] = 0x5f; /* Card Command Classes */ 387 sd->csd[5] = 0x50 | /* Max. read data block length */ 388 HWBLOCK_SHIFT; 389 sd->csd[6] = 0xe0 | /* Partial block for read allowed */ 390 ((csize >> 10) & 0x03); 391 sd->csd[7] = 0x00 | /* Device size */ 392 ((csize >> 2) & 0xff); 393 sd->csd[8] = 0x3f | /* Max. read current */ 394 ((csize << 6) & 0xc0); 395 sd->csd[9] = 0xfc | /* Max. write current */ 396 ((CMULT_SHIFT - 2) >> 1); 397 sd->csd[10] = 0x40 | /* Erase sector size */ 398 (((CMULT_SHIFT - 2) << 7) & 0x80) | (sectsize >> 1); 399 sd->csd[11] = 0x00 | /* Write protect group size */ 400 ((sectsize << 7) & 0x80) | wpsize; 401 sd->csd[12] = 0x90 | /* Write speed factor */ 402 (HWBLOCK_SHIFT >> 2); 403 sd->csd[13] = 0x20 | /* Max. write data block length */ 404 ((HWBLOCK_SHIFT << 6) & 0xc0); 405 sd->csd[14] = 0x00; /* File format group */ 406 } else { /* SDHC */ 407 size /= 512 * KiB; 408 size -= 1; 409 sd->csd[0] = 0x40; 410 sd->csd[1] = 0x0e; 411 sd->csd[2] = 0x00; 412 sd->csd[3] = 0x32; 413 sd->csd[4] = 0x5b; 414 sd->csd[5] = 0x59; 415 sd->csd[6] = 0x00; 416 sd->csd[7] = (size >> 16) & 0xff; 417 sd->csd[8] = (size >> 8) & 0xff; 418 sd->csd[9] = (size & 0xff); 419 sd->csd[10] = 0x7f; 420 sd->csd[11] = 0x80; 421 sd->csd[12] = 0x0a; 422 sd->csd[13] = 0x40; 423 sd->csd[14] = 0x00; 424 } 425 sd->csd[15] = (sd_crc7(sd->csd, 15) << 1) | 1; 426 } 427 428 static void sd_set_rca(SDState *sd) 429 { 430 sd->rca += 0x4567; 431 } 432 433 FIELD(CSR, AKE_SEQ_ERROR, 3, 1) 434 FIELD(CSR, APP_CMD, 5, 1) 435 FIELD(CSR, FX_EVENT, 6, 1) 436 FIELD(CSR, READY_FOR_DATA, 8, 1) 437 FIELD(CSR, CURRENT_STATE, 9, 4) 438 FIELD(CSR, ERASE_RESET, 13, 1) 439 FIELD(CSR, CARD_ECC_DISABLED, 14, 1) 440 FIELD(CSR, WP_ERASE_SKIP, 15, 1) 441 FIELD(CSR, CSD_OVERWRITE, 16, 1) 442 FIELD(CSR, DEFERRED_RESPONSE, 17, 1) 443 FIELD(CSR, ERROR, 19, 1) 444 FIELD(CSR, CC_ERROR, 20, 1) 445 FIELD(CSR, CARD_ECC_FAILED, 21, 1) 446 FIELD(CSR, ILLEGAL_COMMAND, 22, 1) 447 FIELD(CSR, COM_CRC_ERROR, 23, 1) 448 FIELD(CSR, LOCK_UNLOCK_FAILED, 24, 1) 449 FIELD(CSR, CARD_IS_LOCKED, 25, 1) 450 FIELD(CSR, WP_VIOLATION, 26, 1) 451 FIELD(CSR, ERASE_PARAM, 27, 1) 452 FIELD(CSR, ERASE_SEQ_ERROR, 28, 1) 453 FIELD(CSR, BLOCK_LEN_ERROR, 29, 1) 454 FIELD(CSR, ADDRESS_ERROR, 30, 1) 455 FIELD(CSR, OUT_OF_RANGE, 31, 1) 456 457 /* Card status bits, split by clear condition: 458 * A : According to the card current state 459 * B : Always related to the previous command 460 * C : Cleared by read 461 */ 462 #define CARD_STATUS_A (R_CSR_READY_FOR_DATA_MASK \ 463 | R_CSR_CARD_ECC_DISABLED_MASK \ 464 | R_CSR_CARD_IS_LOCKED_MASK) 465 #define CARD_STATUS_B (R_CSR_CURRENT_STATE_MASK \ 466 | R_CSR_ILLEGAL_COMMAND_MASK \ 467 | R_CSR_COM_CRC_ERROR_MASK) 468 #define CARD_STATUS_C (R_CSR_AKE_SEQ_ERROR_MASK \ 469 | R_CSR_APP_CMD_MASK \ 470 | R_CSR_ERASE_RESET_MASK \ 471 | R_CSR_WP_ERASE_SKIP_MASK \ 472 | R_CSR_CSD_OVERWRITE_MASK \ 473 | R_CSR_ERROR_MASK \ 474 | R_CSR_CC_ERROR_MASK \ 475 | R_CSR_CARD_ECC_FAILED_MASK \ 476 | R_CSR_LOCK_UNLOCK_FAILED_MASK \ 477 | R_CSR_WP_VIOLATION_MASK \ 478 | R_CSR_ERASE_PARAM_MASK \ 479 | R_CSR_ERASE_SEQ_ERROR_MASK \ 480 | R_CSR_BLOCK_LEN_ERROR_MASK \ 481 | R_CSR_ADDRESS_ERROR_MASK \ 482 | R_CSR_OUT_OF_RANGE_MASK) 483 484 static void sd_set_cardstatus(SDState *sd) 485 { 486 sd->card_status = 0x00000100; 487 } 488 489 static void sd_set_sdstatus(SDState *sd) 490 { 491 memset(sd->sd_status, 0, 64); 492 } 493 494 static int sd_req_crc_validate(SDRequest *req) 495 { 496 uint8_t buffer[5]; 497 buffer[0] = 0x40 | req->cmd; 498 stl_be_p(&buffer[1], req->arg); 499 return 0; 500 return sd_crc7(buffer, 5) != req->crc; /* TODO */ 501 } 502 503 static void sd_response_r1_make(SDState *sd, uint8_t *response) 504 { 505 stl_be_p(response, sd->card_status); 506 507 /* Clear the "clear on read" status bits */ 508 sd->card_status &= ~CARD_STATUS_C; 509 } 510 511 static void sd_response_r3_make(SDState *sd, uint8_t *response) 512 { 513 stl_be_p(response, sd->ocr & ACMD41_R3_MASK); 514 } 515 516 static void sd_response_r6_make(SDState *sd, uint8_t *response) 517 { 518 uint16_t status; 519 520 status = ((sd->card_status >> 8) & 0xc000) | 521 ((sd->card_status >> 6) & 0x2000) | 522 (sd->card_status & 0x1fff); 523 sd->card_status &= ~(CARD_STATUS_C & 0xc81fff); 524 stw_be_p(response + 0, sd->rca); 525 stw_be_p(response + 2, status); 526 } 527 528 static void sd_response_r7_make(SDState *sd, uint8_t *response) 529 { 530 stl_be_p(response, sd->vhs); 531 } 532 533 static inline uint64_t sd_addr_to_wpnum(uint64_t addr) 534 { 535 return addr >> (HWBLOCK_SHIFT + SECTOR_SHIFT + WPGROUP_SHIFT); 536 } 537 538 static void sd_reset(DeviceState *dev) 539 { 540 SDState *sd = SD_CARD(dev); 541 uint64_t size; 542 uint64_t sect; 543 544 trace_sdcard_reset(); 545 if (sd->blk) { 546 blk_get_geometry(sd->blk, §); 547 } else { 548 sect = 0; 549 } 550 size = sect << 9; 551 552 sect = sd_addr_to_wpnum(size) + 1; 553 554 sd->state = sd_idle_state; 555 sd->rca = 0x0000; 556 sd_set_ocr(sd); 557 sd_set_scr(sd); 558 sd_set_cid(sd); 559 sd_set_csd(sd, size); 560 sd_set_cardstatus(sd); 561 sd_set_sdstatus(sd); 562 563 g_free(sd->wp_groups); 564 sd->wp_switch = sd->blk ? blk_is_read_only(sd->blk) : false; 565 sd->wpgrps_size = sect; 566 sd->wp_groups = bitmap_new(sd->wpgrps_size); 567 memset(sd->function_group, 0, sizeof(sd->function_group)); 568 sd->erase_start = 0; 569 sd->erase_end = 0; 570 sd->size = size; 571 sd->blk_len = 0x200; 572 sd->pwd_len = 0; 573 sd->expecting_acmd = false; 574 sd->dat_lines = 0xf; 575 sd->cmd_line = true; 576 sd->multi_blk_cnt = 0; 577 } 578 579 static bool sd_get_inserted(SDState *sd) 580 { 581 return sd->blk && blk_is_inserted(sd->blk); 582 } 583 584 static bool sd_get_readonly(SDState *sd) 585 { 586 return sd->wp_switch; 587 } 588 589 static void sd_cardchange(void *opaque, bool load, Error **errp) 590 { 591 SDState *sd = opaque; 592 DeviceState *dev = DEVICE(sd); 593 SDBus *sdbus = SD_BUS(qdev_get_parent_bus(dev)); 594 bool inserted = sd_get_inserted(sd); 595 bool readonly = sd_get_readonly(sd); 596 597 if (inserted) { 598 trace_sdcard_inserted(readonly); 599 sd_reset(dev); 600 } else { 601 trace_sdcard_ejected(); 602 } 603 604 /* The IRQ notification is for legacy non-QOM SD controller devices; 605 * QOMified controllers use the SDBus APIs. 606 */ 607 if (sdbus) { 608 sdbus_set_inserted(sdbus, inserted); 609 if (inserted) { 610 sdbus_set_readonly(sdbus, readonly); 611 } 612 } else { 613 qemu_set_irq(sd->inserted_cb, inserted); 614 if (inserted) { 615 qemu_set_irq(sd->readonly_cb, readonly); 616 } 617 } 618 } 619 620 static const BlockDevOps sd_block_ops = { 621 .change_media_cb = sd_cardchange, 622 }; 623 624 static bool sd_ocr_vmstate_needed(void *opaque) 625 { 626 SDState *sd = opaque; 627 628 /* Include the OCR state (and timer) if it is not yet powered up */ 629 return !FIELD_EX32(sd->ocr, OCR, CARD_POWER_UP); 630 } 631 632 static const VMStateDescription sd_ocr_vmstate = { 633 .name = "sd-card/ocr-state", 634 .version_id = 1, 635 .minimum_version_id = 1, 636 .needed = sd_ocr_vmstate_needed, 637 .fields = (VMStateField[]) { 638 VMSTATE_UINT32(ocr, SDState), 639 VMSTATE_TIMER_PTR(ocr_power_timer, SDState), 640 VMSTATE_END_OF_LIST() 641 }, 642 }; 643 644 static int sd_vmstate_pre_load(void *opaque) 645 { 646 SDState *sd = opaque; 647 648 /* If the OCR state is not included (prior versions, or not 649 * needed), then the OCR must be set as powered up. If the OCR state 650 * is included, this will be replaced by the state restore. 651 */ 652 sd_ocr_powerup(sd); 653 654 return 0; 655 } 656 657 static const VMStateDescription sd_vmstate = { 658 .name = "sd-card", 659 .version_id = 1, 660 .minimum_version_id = 1, 661 .pre_load = sd_vmstate_pre_load, 662 .fields = (VMStateField[]) { 663 VMSTATE_UINT32(mode, SDState), 664 VMSTATE_INT32(state, SDState), 665 VMSTATE_UINT8_ARRAY(cid, SDState, 16), 666 VMSTATE_UINT8_ARRAY(csd, SDState, 16), 667 VMSTATE_UINT16(rca, SDState), 668 VMSTATE_UINT32(card_status, SDState), 669 VMSTATE_PARTIAL_BUFFER(sd_status, SDState, 1), 670 VMSTATE_UINT32(vhs, SDState), 671 VMSTATE_BITMAP(wp_groups, SDState, 0, wpgrps_size), 672 VMSTATE_UINT32(blk_len, SDState), 673 VMSTATE_UINT32(multi_blk_cnt, SDState), 674 VMSTATE_UINT32(erase_start, SDState), 675 VMSTATE_UINT32(erase_end, SDState), 676 VMSTATE_UINT8_ARRAY(pwd, SDState, 16), 677 VMSTATE_UINT32(pwd_len, SDState), 678 VMSTATE_UINT8_ARRAY(function_group, SDState, 6), 679 VMSTATE_UINT8(current_cmd, SDState), 680 VMSTATE_BOOL(expecting_acmd, SDState), 681 VMSTATE_UINT32(blk_written, SDState), 682 VMSTATE_UINT64(data_start, SDState), 683 VMSTATE_UINT32(data_offset, SDState), 684 VMSTATE_UINT8_ARRAY(data, SDState, 512), 685 VMSTATE_UNUSED_V(1, 512), 686 VMSTATE_BOOL(enable, SDState), 687 VMSTATE_END_OF_LIST() 688 }, 689 .subsections = (const VMStateDescription*[]) { 690 &sd_ocr_vmstate, 691 NULL 692 }, 693 }; 694 695 /* Legacy initialization function for use by non-qdevified callers */ 696 SDState *sd_init(BlockBackend *blk, bool is_spi) 697 { 698 Object *obj; 699 DeviceState *dev; 700 Error *err = NULL; 701 702 obj = object_new(TYPE_SD_CARD); 703 dev = DEVICE(obj); 704 qdev_prop_set_drive(dev, "drive", blk, &err); 705 if (err) { 706 error_report("sd_init failed: %s", error_get_pretty(err)); 707 return NULL; 708 } 709 qdev_prop_set_bit(dev, "spi", is_spi); 710 object_property_set_bool(obj, true, "realized", &err); 711 if (err) { 712 error_report("sd_init failed: %s", error_get_pretty(err)); 713 return NULL; 714 } 715 716 return SD_CARD(dev); 717 } 718 719 void sd_set_cb(SDState *sd, qemu_irq readonly, qemu_irq insert) 720 { 721 sd->readonly_cb = readonly; 722 sd->inserted_cb = insert; 723 qemu_set_irq(readonly, sd->blk ? blk_is_read_only(sd->blk) : 0); 724 qemu_set_irq(insert, sd->blk ? blk_is_inserted(sd->blk) : 0); 725 } 726 727 static void sd_erase(SDState *sd) 728 { 729 int i; 730 uint64_t erase_start = sd->erase_start; 731 uint64_t erase_end = sd->erase_end; 732 733 trace_sdcard_erase(); 734 if (!sd->erase_start || !sd->erase_end) { 735 sd->card_status |= ERASE_SEQ_ERROR; 736 return; 737 } 738 739 if (FIELD_EX32(sd->ocr, OCR, CARD_CAPACITY)) { 740 /* High capacity memory card: erase units are 512 byte blocks */ 741 erase_start *= 512; 742 erase_end *= 512; 743 } 744 745 erase_start = sd_addr_to_wpnum(erase_start); 746 erase_end = sd_addr_to_wpnum(erase_end); 747 sd->erase_start = 0; 748 sd->erase_end = 0; 749 sd->csd[14] |= 0x40; 750 751 for (i = erase_start; i <= erase_end; i++) { 752 if (test_bit(i, sd->wp_groups)) { 753 sd->card_status |= WP_ERASE_SKIP; 754 } 755 } 756 } 757 758 static uint32_t sd_wpbits(SDState *sd, uint64_t addr) 759 { 760 uint32_t i, wpnum; 761 uint32_t ret = 0; 762 763 wpnum = sd_addr_to_wpnum(addr); 764 765 for (i = 0; i < 32; i++, wpnum++, addr += WPGROUP_SIZE) { 766 if (addr < sd->size && test_bit(wpnum, sd->wp_groups)) { 767 ret |= (1 << i); 768 } 769 } 770 771 return ret; 772 } 773 774 static void sd_function_switch(SDState *sd, uint32_t arg) 775 { 776 int i, mode, new_func; 777 mode = !!(arg & 0x80000000); 778 779 sd->data[0] = 0x00; /* Maximum current consumption */ 780 sd->data[1] = 0x01; 781 sd->data[2] = 0x80; /* Supported group 6 functions */ 782 sd->data[3] = 0x01; 783 sd->data[4] = 0x80; /* Supported group 5 functions */ 784 sd->data[5] = 0x01; 785 sd->data[6] = 0x80; /* Supported group 4 functions */ 786 sd->data[7] = 0x01; 787 sd->data[8] = 0x80; /* Supported group 3 functions */ 788 sd->data[9] = 0x01; 789 sd->data[10] = 0x80; /* Supported group 2 functions */ 790 sd->data[11] = 0x43; 791 sd->data[12] = 0x80; /* Supported group 1 functions */ 792 sd->data[13] = 0x03; 793 for (i = 0; i < 6; i ++) { 794 new_func = (arg >> (i * 4)) & 0x0f; 795 if (mode && new_func != 0x0f) 796 sd->function_group[i] = new_func; 797 sd->data[14 + (i >> 1)] = new_func << ((i * 4) & 4); 798 } 799 memset(&sd->data[17], 0, 47); 800 stw_be_p(sd->data + 64, sd_crc16(sd->data, 64)); 801 } 802 803 static inline bool sd_wp_addr(SDState *sd, uint64_t addr) 804 { 805 return test_bit(sd_addr_to_wpnum(addr), sd->wp_groups); 806 } 807 808 static void sd_lock_command(SDState *sd) 809 { 810 int erase, lock, clr_pwd, set_pwd, pwd_len; 811 erase = !!(sd->data[0] & 0x08); 812 lock = sd->data[0] & 0x04; 813 clr_pwd = sd->data[0] & 0x02; 814 set_pwd = sd->data[0] & 0x01; 815 816 if (sd->blk_len > 1) 817 pwd_len = sd->data[1]; 818 else 819 pwd_len = 0; 820 821 if (lock) { 822 trace_sdcard_lock(); 823 } else { 824 trace_sdcard_unlock(); 825 } 826 if (erase) { 827 if (!(sd->card_status & CARD_IS_LOCKED) || sd->blk_len > 1 || 828 set_pwd || clr_pwd || lock || sd->wp_switch || 829 (sd->csd[14] & 0x20)) { 830 sd->card_status |= LOCK_UNLOCK_FAILED; 831 return; 832 } 833 bitmap_zero(sd->wp_groups, sd->wpgrps_size); 834 sd->csd[14] &= ~0x10; 835 sd->card_status &= ~CARD_IS_LOCKED; 836 sd->pwd_len = 0; 837 /* Erasing the entire card here! */ 838 fprintf(stderr, "SD: Card force-erased by CMD42\n"); 839 return; 840 } 841 842 if (sd->blk_len < 2 + pwd_len || 843 pwd_len <= sd->pwd_len || 844 pwd_len > sd->pwd_len + 16) { 845 sd->card_status |= LOCK_UNLOCK_FAILED; 846 return; 847 } 848 849 if (sd->pwd_len && memcmp(sd->pwd, sd->data + 2, sd->pwd_len)) { 850 sd->card_status |= LOCK_UNLOCK_FAILED; 851 return; 852 } 853 854 pwd_len -= sd->pwd_len; 855 if ((pwd_len && !set_pwd) || 856 (clr_pwd && (set_pwd || lock)) || 857 (lock && !sd->pwd_len && !set_pwd) || 858 (!set_pwd && !clr_pwd && 859 (((sd->card_status & CARD_IS_LOCKED) && lock) || 860 (!(sd->card_status & CARD_IS_LOCKED) && !lock)))) { 861 sd->card_status |= LOCK_UNLOCK_FAILED; 862 return; 863 } 864 865 if (set_pwd) { 866 memcpy(sd->pwd, sd->data + 2 + sd->pwd_len, pwd_len); 867 sd->pwd_len = pwd_len; 868 } 869 870 if (clr_pwd) { 871 sd->pwd_len = 0; 872 } 873 874 if (lock) 875 sd->card_status |= CARD_IS_LOCKED; 876 else 877 sd->card_status &= ~CARD_IS_LOCKED; 878 } 879 880 static sd_rsp_type_t sd_normal_command(SDState *sd, SDRequest req) 881 { 882 uint32_t rca = 0x0000; 883 uint64_t addr = (sd->ocr & (1 << 30)) ? (uint64_t) req.arg << 9 : req.arg; 884 885 /* CMD55 precedes an ACMD, so we are not interested in tracing it. 886 * However there is no ACMD55, so we want to trace this particular case. 887 */ 888 if (req.cmd != 55 || sd->expecting_acmd) { 889 trace_sdcard_normal_command(sd->proto_name, 890 sd_cmd_name(req.cmd), req.cmd, 891 req.arg, sd_state_name(sd->state)); 892 } 893 894 /* Not interpreting this as an app command */ 895 sd->card_status &= ~APP_CMD; 896 897 if (sd_cmd_type[req.cmd] == sd_ac 898 || sd_cmd_type[req.cmd] == sd_adtc) { 899 rca = req.arg >> 16; 900 } 901 902 /* CMD23 (set block count) must be immediately followed by CMD18 or CMD25 903 * if not, its effects are cancelled */ 904 if (sd->multi_blk_cnt != 0 && !(req.cmd == 18 || req.cmd == 25)) { 905 sd->multi_blk_cnt = 0; 906 } 907 908 switch (req.cmd) { 909 /* Basic commands (Class 0 and Class 1) */ 910 case 0: /* CMD0: GO_IDLE_STATE */ 911 switch (sd->state) { 912 case sd_inactive_state: 913 return sd->spi ? sd_r1 : sd_r0; 914 915 default: 916 sd->state = sd_idle_state; 917 sd_reset(DEVICE(sd)); 918 return sd->spi ? sd_r1 : sd_r0; 919 } 920 break; 921 922 case 1: /* CMD1: SEND_OP_CMD */ 923 if (!sd->spi) 924 goto bad_cmd; 925 926 sd->state = sd_transfer_state; 927 return sd_r1; 928 929 case 2: /* CMD2: ALL_SEND_CID */ 930 if (sd->spi) 931 goto bad_cmd; 932 switch (sd->state) { 933 case sd_ready_state: 934 sd->state = sd_identification_state; 935 return sd_r2_i; 936 937 default: 938 break; 939 } 940 break; 941 942 case 3: /* CMD3: SEND_RELATIVE_ADDR */ 943 if (sd->spi) 944 goto bad_cmd; 945 switch (sd->state) { 946 case sd_identification_state: 947 case sd_standby_state: 948 sd->state = sd_standby_state; 949 sd_set_rca(sd); 950 return sd_r6; 951 952 default: 953 break; 954 } 955 break; 956 957 case 4: /* CMD4: SEND_DSR */ 958 if (sd->spi) 959 goto bad_cmd; 960 switch (sd->state) { 961 case sd_standby_state: 962 break; 963 964 default: 965 break; 966 } 967 break; 968 969 case 5: /* CMD5: reserved for SDIO cards */ 970 return sd_illegal; 971 972 case 6: /* CMD6: SWITCH_FUNCTION */ 973 switch (sd->mode) { 974 case sd_data_transfer_mode: 975 sd_function_switch(sd, req.arg); 976 sd->state = sd_sendingdata_state; 977 sd->data_start = 0; 978 sd->data_offset = 0; 979 return sd_r1; 980 981 default: 982 break; 983 } 984 break; 985 986 case 7: /* CMD7: SELECT/DESELECT_CARD */ 987 if (sd->spi) 988 goto bad_cmd; 989 switch (sd->state) { 990 case sd_standby_state: 991 if (sd->rca != rca) 992 return sd_r0; 993 994 sd->state = sd_transfer_state; 995 return sd_r1b; 996 997 case sd_transfer_state: 998 case sd_sendingdata_state: 999 if (sd->rca == rca) 1000 break; 1001 1002 sd->state = sd_standby_state; 1003 return sd_r1b; 1004 1005 case sd_disconnect_state: 1006 if (sd->rca != rca) 1007 return sd_r0; 1008 1009 sd->state = sd_programming_state; 1010 return sd_r1b; 1011 1012 case sd_programming_state: 1013 if (sd->rca == rca) 1014 break; 1015 1016 sd->state = sd_disconnect_state; 1017 return sd_r1b; 1018 1019 default: 1020 break; 1021 } 1022 break; 1023 1024 case 8: /* CMD8: SEND_IF_COND */ 1025 if (sd->spec_version < SD_PHY_SPECv2_00_VERS) { 1026 break; 1027 } 1028 if (sd->state != sd_idle_state) { 1029 break; 1030 } 1031 sd->vhs = 0; 1032 1033 /* No response if not exactly one VHS bit is set. */ 1034 if (!(req.arg >> 8) || (req.arg >> (ctz32(req.arg & ~0xff) + 1))) { 1035 return sd->spi ? sd_r7 : sd_r0; 1036 } 1037 1038 /* Accept. */ 1039 sd->vhs = req.arg; 1040 return sd_r7; 1041 1042 case 9: /* CMD9: SEND_CSD */ 1043 switch (sd->state) { 1044 case sd_standby_state: 1045 if (sd->rca != rca) 1046 return sd_r0; 1047 1048 return sd_r2_s; 1049 1050 case sd_transfer_state: 1051 if (!sd->spi) 1052 break; 1053 sd->state = sd_sendingdata_state; 1054 memcpy(sd->data, sd->csd, 16); 1055 sd->data_start = addr; 1056 sd->data_offset = 0; 1057 return sd_r1; 1058 1059 default: 1060 break; 1061 } 1062 break; 1063 1064 case 10: /* CMD10: SEND_CID */ 1065 switch (sd->state) { 1066 case sd_standby_state: 1067 if (sd->rca != rca) 1068 return sd_r0; 1069 1070 return sd_r2_i; 1071 1072 case sd_transfer_state: 1073 if (!sd->spi) 1074 break; 1075 sd->state = sd_sendingdata_state; 1076 memcpy(sd->data, sd->cid, 16); 1077 sd->data_start = addr; 1078 sd->data_offset = 0; 1079 return sd_r1; 1080 1081 default: 1082 break; 1083 } 1084 break; 1085 1086 case 12: /* CMD12: STOP_TRANSMISSION */ 1087 switch (sd->state) { 1088 case sd_sendingdata_state: 1089 sd->state = sd_transfer_state; 1090 return sd_r1b; 1091 1092 case sd_receivingdata_state: 1093 sd->state = sd_programming_state; 1094 /* Bzzzzzzztt .... Operation complete. */ 1095 sd->state = sd_transfer_state; 1096 return sd_r1b; 1097 1098 default: 1099 break; 1100 } 1101 break; 1102 1103 case 13: /* CMD13: SEND_STATUS */ 1104 switch (sd->mode) { 1105 case sd_data_transfer_mode: 1106 if (sd->rca != rca) 1107 return sd_r0; 1108 1109 return sd_r1; 1110 1111 default: 1112 break; 1113 } 1114 break; 1115 1116 case 15: /* CMD15: GO_INACTIVE_STATE */ 1117 if (sd->spi) 1118 goto bad_cmd; 1119 switch (sd->mode) { 1120 case sd_data_transfer_mode: 1121 if (sd->rca != rca) 1122 return sd_r0; 1123 1124 sd->state = sd_inactive_state; 1125 return sd_r0; 1126 1127 default: 1128 break; 1129 } 1130 break; 1131 1132 /* Block read commands (Classs 2) */ 1133 case 16: /* CMD16: SET_BLOCKLEN */ 1134 switch (sd->state) { 1135 case sd_transfer_state: 1136 if (req.arg > (1 << HWBLOCK_SHIFT)) { 1137 sd->card_status |= BLOCK_LEN_ERROR; 1138 } else { 1139 trace_sdcard_set_blocklen(req.arg); 1140 sd->blk_len = req.arg; 1141 } 1142 1143 return sd_r1; 1144 1145 default: 1146 break; 1147 } 1148 break; 1149 1150 case 17: /* CMD17: READ_SINGLE_BLOCK */ 1151 switch (sd->state) { 1152 case sd_transfer_state: 1153 sd->state = sd_sendingdata_state; 1154 sd->data_start = addr; 1155 sd->data_offset = 0; 1156 1157 if (sd->data_start + sd->blk_len > sd->size) 1158 sd->card_status |= ADDRESS_ERROR; 1159 return sd_r1; 1160 1161 default: 1162 break; 1163 } 1164 break; 1165 1166 case 18: /* CMD18: READ_MULTIPLE_BLOCK */ 1167 switch (sd->state) { 1168 case sd_transfer_state: 1169 sd->state = sd_sendingdata_state; 1170 sd->data_start = addr; 1171 sd->data_offset = 0; 1172 1173 if (sd->data_start + sd->blk_len > sd->size) 1174 sd->card_status |= ADDRESS_ERROR; 1175 return sd_r1; 1176 1177 default: 1178 break; 1179 } 1180 break; 1181 1182 case 19: /* CMD19: SEND_TUNING_BLOCK (SD) */ 1183 if (sd->spec_version < SD_PHY_SPECv3_01_VERS) { 1184 break; 1185 } 1186 if (sd->state == sd_transfer_state) { 1187 sd->state = sd_sendingdata_state; 1188 sd->data_offset = 0; 1189 return sd_r1; 1190 } 1191 break; 1192 1193 case 23: /* CMD23: SET_BLOCK_COUNT */ 1194 if (sd->spec_version < SD_PHY_SPECv3_01_VERS) { 1195 break; 1196 } 1197 switch (sd->state) { 1198 case sd_transfer_state: 1199 sd->multi_blk_cnt = req.arg; 1200 return sd_r1; 1201 1202 default: 1203 break; 1204 } 1205 break; 1206 1207 /* Block write commands (Class 4) */ 1208 case 24: /* CMD24: WRITE_SINGLE_BLOCK */ 1209 switch (sd->state) { 1210 case sd_transfer_state: 1211 /* Writing in SPI mode not implemented. */ 1212 if (sd->spi) 1213 break; 1214 sd->state = sd_receivingdata_state; 1215 sd->data_start = addr; 1216 sd->data_offset = 0; 1217 sd->blk_written = 0; 1218 1219 if (sd->data_start + sd->blk_len > sd->size) 1220 sd->card_status |= ADDRESS_ERROR; 1221 if (sd_wp_addr(sd, sd->data_start)) 1222 sd->card_status |= WP_VIOLATION; 1223 if (sd->csd[14] & 0x30) 1224 sd->card_status |= WP_VIOLATION; 1225 return sd_r1; 1226 1227 default: 1228 break; 1229 } 1230 break; 1231 1232 case 25: /* CMD25: WRITE_MULTIPLE_BLOCK */ 1233 switch (sd->state) { 1234 case sd_transfer_state: 1235 /* Writing in SPI mode not implemented. */ 1236 if (sd->spi) 1237 break; 1238 sd->state = sd_receivingdata_state; 1239 sd->data_start = addr; 1240 sd->data_offset = 0; 1241 sd->blk_written = 0; 1242 1243 if (sd->data_start + sd->blk_len > sd->size) 1244 sd->card_status |= ADDRESS_ERROR; 1245 if (sd_wp_addr(sd, sd->data_start)) 1246 sd->card_status |= WP_VIOLATION; 1247 if (sd->csd[14] & 0x30) 1248 sd->card_status |= WP_VIOLATION; 1249 return sd_r1; 1250 1251 default: 1252 break; 1253 } 1254 break; 1255 1256 case 26: /* CMD26: PROGRAM_CID */ 1257 if (sd->spi) 1258 goto bad_cmd; 1259 switch (sd->state) { 1260 case sd_transfer_state: 1261 sd->state = sd_receivingdata_state; 1262 sd->data_start = 0; 1263 sd->data_offset = 0; 1264 return sd_r1; 1265 1266 default: 1267 break; 1268 } 1269 break; 1270 1271 case 27: /* CMD27: PROGRAM_CSD */ 1272 switch (sd->state) { 1273 case sd_transfer_state: 1274 sd->state = sd_receivingdata_state; 1275 sd->data_start = 0; 1276 sd->data_offset = 0; 1277 return sd_r1; 1278 1279 default: 1280 break; 1281 } 1282 break; 1283 1284 /* Write protection (Class 6) */ 1285 case 28: /* CMD28: SET_WRITE_PROT */ 1286 switch (sd->state) { 1287 case sd_transfer_state: 1288 if (addr >= sd->size) { 1289 sd->card_status |= ADDRESS_ERROR; 1290 return sd_r1b; 1291 } 1292 1293 sd->state = sd_programming_state; 1294 set_bit(sd_addr_to_wpnum(addr), sd->wp_groups); 1295 /* Bzzzzzzztt .... Operation complete. */ 1296 sd->state = sd_transfer_state; 1297 return sd_r1b; 1298 1299 default: 1300 break; 1301 } 1302 break; 1303 1304 case 29: /* CMD29: CLR_WRITE_PROT */ 1305 switch (sd->state) { 1306 case sd_transfer_state: 1307 if (addr >= sd->size) { 1308 sd->card_status |= ADDRESS_ERROR; 1309 return sd_r1b; 1310 } 1311 1312 sd->state = sd_programming_state; 1313 clear_bit(sd_addr_to_wpnum(addr), sd->wp_groups); 1314 /* Bzzzzzzztt .... Operation complete. */ 1315 sd->state = sd_transfer_state; 1316 return sd_r1b; 1317 1318 default: 1319 break; 1320 } 1321 break; 1322 1323 case 30: /* CMD30: SEND_WRITE_PROT */ 1324 switch (sd->state) { 1325 case sd_transfer_state: 1326 sd->state = sd_sendingdata_state; 1327 *(uint32_t *) sd->data = sd_wpbits(sd, req.arg); 1328 sd->data_start = addr; 1329 sd->data_offset = 0; 1330 return sd_r1b; 1331 1332 default: 1333 break; 1334 } 1335 break; 1336 1337 /* Erase commands (Class 5) */ 1338 case 32: /* CMD32: ERASE_WR_BLK_START */ 1339 switch (sd->state) { 1340 case sd_transfer_state: 1341 sd->erase_start = req.arg; 1342 return sd_r1; 1343 1344 default: 1345 break; 1346 } 1347 break; 1348 1349 case 33: /* CMD33: ERASE_WR_BLK_END */ 1350 switch (sd->state) { 1351 case sd_transfer_state: 1352 sd->erase_end = req.arg; 1353 return sd_r1; 1354 1355 default: 1356 break; 1357 } 1358 break; 1359 1360 case 38: /* CMD38: ERASE */ 1361 switch (sd->state) { 1362 case sd_transfer_state: 1363 if (sd->csd[14] & 0x30) { 1364 sd->card_status |= WP_VIOLATION; 1365 return sd_r1b; 1366 } 1367 1368 sd->state = sd_programming_state; 1369 sd_erase(sd); 1370 /* Bzzzzzzztt .... Operation complete. */ 1371 sd->state = sd_transfer_state; 1372 return sd_r1b; 1373 1374 default: 1375 break; 1376 } 1377 break; 1378 1379 /* Lock card commands (Class 7) */ 1380 case 42: /* CMD42: LOCK_UNLOCK */ 1381 switch (sd->state) { 1382 case sd_transfer_state: 1383 sd->state = sd_receivingdata_state; 1384 sd->data_start = 0; 1385 sd->data_offset = 0; 1386 return sd_r1; 1387 1388 default: 1389 break; 1390 } 1391 break; 1392 1393 case 52 ... 54: 1394 /* CMD52, CMD53, CMD54: reserved for SDIO cards 1395 * (see the SDIO Simplified Specification V2.0) 1396 * Handle as illegal command but do not complain 1397 * on stderr, as some OSes may use these in their 1398 * probing for presence of an SDIO card. 1399 */ 1400 return sd_illegal; 1401 1402 /* Application specific commands (Class 8) */ 1403 case 55: /* CMD55: APP_CMD */ 1404 switch (sd->state) { 1405 case sd_ready_state: 1406 case sd_identification_state: 1407 case sd_inactive_state: 1408 return sd_illegal; 1409 case sd_idle_state: 1410 if (rca) { 1411 qemu_log_mask(LOG_GUEST_ERROR, 1412 "SD: illegal RCA 0x%04x for APP_CMD\n", req.cmd); 1413 } 1414 default: 1415 break; 1416 } 1417 if (!sd->spi) { 1418 if (sd->rca != rca) { 1419 return sd_r0; 1420 } 1421 } 1422 sd->expecting_acmd = true; 1423 sd->card_status |= APP_CMD; 1424 return sd_r1; 1425 1426 case 56: /* CMD56: GEN_CMD */ 1427 switch (sd->state) { 1428 case sd_transfer_state: 1429 sd->data_offset = 0; 1430 if (req.arg & 1) 1431 sd->state = sd_sendingdata_state; 1432 else 1433 sd->state = sd_receivingdata_state; 1434 return sd_r1; 1435 1436 default: 1437 break; 1438 } 1439 break; 1440 1441 case 58: /* CMD58: READ_OCR (SPI) */ 1442 if (!sd->spi) { 1443 goto bad_cmd; 1444 } 1445 return sd_r3; 1446 1447 case 59: /* CMD59: CRC_ON_OFF (SPI) */ 1448 if (!sd->spi) { 1449 goto bad_cmd; 1450 } 1451 goto unimplemented_spi_cmd; 1452 1453 default: 1454 bad_cmd: 1455 qemu_log_mask(LOG_GUEST_ERROR, "SD: Unknown CMD%i\n", req.cmd); 1456 return sd_illegal; 1457 1458 unimplemented_spi_cmd: 1459 /* Commands that are recognised but not yet implemented in SPI mode. */ 1460 qemu_log_mask(LOG_UNIMP, "SD: CMD%i not implemented in SPI mode\n", 1461 req.cmd); 1462 return sd_illegal; 1463 } 1464 1465 qemu_log_mask(LOG_GUEST_ERROR, "SD: CMD%i in a wrong state\n", req.cmd); 1466 return sd_illegal; 1467 } 1468 1469 static sd_rsp_type_t sd_app_command(SDState *sd, 1470 SDRequest req) 1471 { 1472 trace_sdcard_app_command(sd->proto_name, sd_acmd_name(req.cmd), 1473 req.cmd, req.arg, sd_state_name(sd->state)); 1474 sd->card_status |= APP_CMD; 1475 switch (req.cmd) { 1476 case 6: /* ACMD6: SET_BUS_WIDTH */ 1477 if (sd->spi) { 1478 goto unimplemented_spi_cmd; 1479 } 1480 switch (sd->state) { 1481 case sd_transfer_state: 1482 sd->sd_status[0] &= 0x3f; 1483 sd->sd_status[0] |= (req.arg & 0x03) << 6; 1484 return sd_r1; 1485 1486 default: 1487 break; 1488 } 1489 break; 1490 1491 case 13: /* ACMD13: SD_STATUS */ 1492 switch (sd->state) { 1493 case sd_transfer_state: 1494 sd->state = sd_sendingdata_state; 1495 sd->data_start = 0; 1496 sd->data_offset = 0; 1497 return sd_r1; 1498 1499 default: 1500 break; 1501 } 1502 break; 1503 1504 case 22: /* ACMD22: SEND_NUM_WR_BLOCKS */ 1505 switch (sd->state) { 1506 case sd_transfer_state: 1507 *(uint32_t *) sd->data = sd->blk_written; 1508 1509 sd->state = sd_sendingdata_state; 1510 sd->data_start = 0; 1511 sd->data_offset = 0; 1512 return sd_r1; 1513 1514 default: 1515 break; 1516 } 1517 break; 1518 1519 case 23: /* ACMD23: SET_WR_BLK_ERASE_COUNT */ 1520 switch (sd->state) { 1521 case sd_transfer_state: 1522 return sd_r1; 1523 1524 default: 1525 break; 1526 } 1527 break; 1528 1529 case 41: /* ACMD41: SD_APP_OP_COND */ 1530 if (sd->spi) { 1531 /* SEND_OP_CMD */ 1532 sd->state = sd_transfer_state; 1533 return sd_r1; 1534 } 1535 if (sd->state != sd_idle_state) { 1536 break; 1537 } 1538 /* If it's the first ACMD41 since reset, we need to decide 1539 * whether to power up. If this is not an enquiry ACMD41, 1540 * we immediately report power on and proceed below to the 1541 * ready state, but if it is, we set a timer to model a 1542 * delay for power up. This works around a bug in EDK2 1543 * UEFI, which sends an initial enquiry ACMD41, but 1544 * assumes that the card is in ready state as soon as it 1545 * sees the power up bit set. */ 1546 if (!FIELD_EX32(sd->ocr, OCR, CARD_POWER_UP)) { 1547 if ((req.arg & ACMD41_ENQUIRY_MASK) != 0) { 1548 timer_del(sd->ocr_power_timer); 1549 sd_ocr_powerup(sd); 1550 } else { 1551 trace_sdcard_inquiry_cmd41(); 1552 if (!timer_pending(sd->ocr_power_timer)) { 1553 timer_mod_ns(sd->ocr_power_timer, 1554 (qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) 1555 + OCR_POWER_DELAY_NS)); 1556 } 1557 } 1558 } 1559 1560 if (FIELD_EX32(sd->ocr & req.arg, OCR, VDD_VOLTAGE_WINDOW)) { 1561 /* We accept any voltage. 10000 V is nothing. 1562 * 1563 * Once we're powered up, we advance straight to ready state 1564 * unless it's an enquiry ACMD41 (bits 23:0 == 0). 1565 */ 1566 sd->state = sd_ready_state; 1567 } 1568 1569 return sd_r3; 1570 1571 case 42: /* ACMD42: SET_CLR_CARD_DETECT */ 1572 switch (sd->state) { 1573 case sd_transfer_state: 1574 /* Bringing in the 50KOhm pull-up resistor... Done. */ 1575 return sd_r1; 1576 1577 default: 1578 break; 1579 } 1580 break; 1581 1582 case 51: /* ACMD51: SEND_SCR */ 1583 switch (sd->state) { 1584 case sd_transfer_state: 1585 sd->state = sd_sendingdata_state; 1586 sd->data_start = 0; 1587 sd->data_offset = 0; 1588 return sd_r1; 1589 1590 default: 1591 break; 1592 } 1593 break; 1594 1595 case 18: /* Reserved for SD security applications */ 1596 case 25: 1597 case 26: 1598 case 38: 1599 case 43 ... 49: 1600 /* Refer to the "SD Specifications Part3 Security Specification" for 1601 * information about the SD Security Features. 1602 */ 1603 qemu_log_mask(LOG_UNIMP, "SD: CMD%i Security not implemented\n", 1604 req.cmd); 1605 return sd_illegal; 1606 1607 default: 1608 /* Fall back to standard commands. */ 1609 return sd_normal_command(sd, req); 1610 1611 unimplemented_spi_cmd: 1612 /* Commands that are recognised but not yet implemented in SPI mode. */ 1613 qemu_log_mask(LOG_UNIMP, "SD: CMD%i not implemented in SPI mode\n", 1614 req.cmd); 1615 return sd_illegal; 1616 } 1617 1618 qemu_log_mask(LOG_GUEST_ERROR, "SD: ACMD%i in a wrong state\n", req.cmd); 1619 return sd_illegal; 1620 } 1621 1622 static int cmd_valid_while_locked(SDState *sd, SDRequest *req) 1623 { 1624 /* Valid commands in locked state: 1625 * basic class (0) 1626 * lock card class (7) 1627 * CMD16 1628 * implicitly, the ACMD prefix CMD55 1629 * ACMD41 and ACMD42 1630 * Anything else provokes an "illegal command" response. 1631 */ 1632 if (sd->expecting_acmd) { 1633 return req->cmd == 41 || req->cmd == 42; 1634 } 1635 if (req->cmd == 16 || req->cmd == 55) { 1636 return 1; 1637 } 1638 return sd_cmd_class[req->cmd] == 0 1639 || sd_cmd_class[req->cmd] == 7; 1640 } 1641 1642 int sd_do_command(SDState *sd, SDRequest *req, 1643 uint8_t *response) { 1644 int last_state; 1645 sd_rsp_type_t rtype; 1646 int rsplen; 1647 1648 if (!sd->blk || !blk_is_inserted(sd->blk) || !sd->enable) { 1649 return 0; 1650 } 1651 1652 if (sd_req_crc_validate(req)) { 1653 sd->card_status |= COM_CRC_ERROR; 1654 rtype = sd_illegal; 1655 goto send_response; 1656 } 1657 1658 if (req->cmd >= SDMMC_CMD_MAX) { 1659 qemu_log_mask(LOG_GUEST_ERROR, "SD: incorrect command 0x%02x\n", 1660 req->cmd); 1661 req->cmd &= 0x3f; 1662 } 1663 1664 if (sd->card_status & CARD_IS_LOCKED) { 1665 if (!cmd_valid_while_locked(sd, req)) { 1666 sd->card_status |= ILLEGAL_COMMAND; 1667 sd->expecting_acmd = false; 1668 qemu_log_mask(LOG_GUEST_ERROR, "SD: Card is locked\n"); 1669 rtype = sd_illegal; 1670 goto send_response; 1671 } 1672 } 1673 1674 last_state = sd->state; 1675 sd_set_mode(sd); 1676 1677 if (sd->expecting_acmd) { 1678 sd->expecting_acmd = false; 1679 rtype = sd_app_command(sd, *req); 1680 } else { 1681 rtype = sd_normal_command(sd, *req); 1682 } 1683 1684 if (rtype == sd_illegal) { 1685 sd->card_status |= ILLEGAL_COMMAND; 1686 } else { 1687 /* Valid command, we can update the 'state before command' bits. 1688 * (Do this now so they appear in r1 responses.) 1689 */ 1690 sd->current_cmd = req->cmd; 1691 sd->card_status &= ~CURRENT_STATE; 1692 sd->card_status |= (last_state << 9); 1693 } 1694 1695 send_response: 1696 switch (rtype) { 1697 case sd_r1: 1698 case sd_r1b: 1699 sd_response_r1_make(sd, response); 1700 rsplen = 4; 1701 break; 1702 1703 case sd_r2_i: 1704 memcpy(response, sd->cid, sizeof(sd->cid)); 1705 rsplen = 16; 1706 break; 1707 1708 case sd_r2_s: 1709 memcpy(response, sd->csd, sizeof(sd->csd)); 1710 rsplen = 16; 1711 break; 1712 1713 case sd_r3: 1714 sd_response_r3_make(sd, response); 1715 rsplen = 4; 1716 break; 1717 1718 case sd_r6: 1719 sd_response_r6_make(sd, response); 1720 rsplen = 4; 1721 break; 1722 1723 case sd_r7: 1724 sd_response_r7_make(sd, response); 1725 rsplen = 4; 1726 break; 1727 1728 case sd_r0: 1729 case sd_illegal: 1730 rsplen = 0; 1731 break; 1732 default: 1733 g_assert_not_reached(); 1734 } 1735 trace_sdcard_response(sd_response_name(rtype), rsplen); 1736 1737 if (rtype != sd_illegal) { 1738 /* Clear the "clear on valid command" status bits now we've 1739 * sent any response 1740 */ 1741 sd->card_status &= ~CARD_STATUS_B; 1742 } 1743 1744 #ifdef DEBUG_SD 1745 qemu_hexdump((const char *)response, stderr, "Response", rsplen); 1746 #endif 1747 1748 return rsplen; 1749 } 1750 1751 static void sd_blk_read(SDState *sd, uint64_t addr, uint32_t len) 1752 { 1753 trace_sdcard_read_block(addr, len); 1754 if (!sd->blk || blk_pread(sd->blk, addr, sd->data, len) < 0) { 1755 fprintf(stderr, "sd_blk_read: read error on host side\n"); 1756 } 1757 } 1758 1759 static void sd_blk_write(SDState *sd, uint64_t addr, uint32_t len) 1760 { 1761 trace_sdcard_write_block(addr, len); 1762 if (!sd->blk || blk_pwrite(sd->blk, addr, sd->data, len, 0) < 0) { 1763 fprintf(stderr, "sd_blk_write: write error on host side\n"); 1764 } 1765 } 1766 1767 #define BLK_READ_BLOCK(a, len) sd_blk_read(sd, a, len) 1768 #define BLK_WRITE_BLOCK(a, len) sd_blk_write(sd, a, len) 1769 #define APP_READ_BLOCK(a, len) memset(sd->data, 0xec, len) 1770 #define APP_WRITE_BLOCK(a, len) 1771 1772 void sd_write_data(SDState *sd, uint8_t value) 1773 { 1774 int i; 1775 1776 if (!sd->blk || !blk_is_inserted(sd->blk) || !sd->enable) 1777 return; 1778 1779 if (sd->state != sd_receivingdata_state) { 1780 qemu_log_mask(LOG_GUEST_ERROR, 1781 "sd_write_data: not in Receiving-Data state\n"); 1782 return; 1783 } 1784 1785 if (sd->card_status & (ADDRESS_ERROR | WP_VIOLATION)) 1786 return; 1787 1788 trace_sdcard_write_data(sd->proto_name, 1789 sd_acmd_name(sd->current_cmd), 1790 sd->current_cmd, value); 1791 switch (sd->current_cmd) { 1792 case 24: /* CMD24: WRITE_SINGLE_BLOCK */ 1793 sd->data[sd->data_offset ++] = value; 1794 if (sd->data_offset >= sd->blk_len) { 1795 /* TODO: Check CRC before committing */ 1796 sd->state = sd_programming_state; 1797 BLK_WRITE_BLOCK(sd->data_start, sd->data_offset); 1798 sd->blk_written ++; 1799 sd->csd[14] |= 0x40; 1800 /* Bzzzzzzztt .... Operation complete. */ 1801 sd->state = sd_transfer_state; 1802 } 1803 break; 1804 1805 case 25: /* CMD25: WRITE_MULTIPLE_BLOCK */ 1806 if (sd->data_offset == 0) { 1807 /* Start of the block - let's check the address is valid */ 1808 if (sd->data_start + sd->blk_len > sd->size) { 1809 sd->card_status |= ADDRESS_ERROR; 1810 break; 1811 } 1812 if (sd_wp_addr(sd, sd->data_start)) { 1813 sd->card_status |= WP_VIOLATION; 1814 break; 1815 } 1816 } 1817 sd->data[sd->data_offset++] = value; 1818 if (sd->data_offset >= sd->blk_len) { 1819 /* TODO: Check CRC before committing */ 1820 sd->state = sd_programming_state; 1821 BLK_WRITE_BLOCK(sd->data_start, sd->data_offset); 1822 sd->blk_written++; 1823 sd->data_start += sd->blk_len; 1824 sd->data_offset = 0; 1825 sd->csd[14] |= 0x40; 1826 1827 /* Bzzzzzzztt .... Operation complete. */ 1828 if (sd->multi_blk_cnt != 0) { 1829 if (--sd->multi_blk_cnt == 0) { 1830 /* Stop! */ 1831 sd->state = sd_transfer_state; 1832 break; 1833 } 1834 } 1835 1836 sd->state = sd_receivingdata_state; 1837 } 1838 break; 1839 1840 case 26: /* CMD26: PROGRAM_CID */ 1841 sd->data[sd->data_offset ++] = value; 1842 if (sd->data_offset >= sizeof(sd->cid)) { 1843 /* TODO: Check CRC before committing */ 1844 sd->state = sd_programming_state; 1845 for (i = 0; i < sizeof(sd->cid); i ++) 1846 if ((sd->cid[i] | 0x00) != sd->data[i]) 1847 sd->card_status |= CID_CSD_OVERWRITE; 1848 1849 if (!(sd->card_status & CID_CSD_OVERWRITE)) 1850 for (i = 0; i < sizeof(sd->cid); i ++) { 1851 sd->cid[i] |= 0x00; 1852 sd->cid[i] &= sd->data[i]; 1853 } 1854 /* Bzzzzzzztt .... Operation complete. */ 1855 sd->state = sd_transfer_state; 1856 } 1857 break; 1858 1859 case 27: /* CMD27: PROGRAM_CSD */ 1860 sd->data[sd->data_offset ++] = value; 1861 if (sd->data_offset >= sizeof(sd->csd)) { 1862 /* TODO: Check CRC before committing */ 1863 sd->state = sd_programming_state; 1864 for (i = 0; i < sizeof(sd->csd); i ++) 1865 if ((sd->csd[i] | sd_csd_rw_mask[i]) != 1866 (sd->data[i] | sd_csd_rw_mask[i])) 1867 sd->card_status |= CID_CSD_OVERWRITE; 1868 1869 /* Copy flag (OTP) & Permanent write protect */ 1870 if (sd->csd[14] & ~sd->data[14] & 0x60) 1871 sd->card_status |= CID_CSD_OVERWRITE; 1872 1873 if (!(sd->card_status & CID_CSD_OVERWRITE)) 1874 for (i = 0; i < sizeof(sd->csd); i ++) { 1875 sd->csd[i] |= sd_csd_rw_mask[i]; 1876 sd->csd[i] &= sd->data[i]; 1877 } 1878 /* Bzzzzzzztt .... Operation complete. */ 1879 sd->state = sd_transfer_state; 1880 } 1881 break; 1882 1883 case 42: /* CMD42: LOCK_UNLOCK */ 1884 sd->data[sd->data_offset ++] = value; 1885 if (sd->data_offset >= sd->blk_len) { 1886 /* TODO: Check CRC before committing */ 1887 sd->state = sd_programming_state; 1888 sd_lock_command(sd); 1889 /* Bzzzzzzztt .... Operation complete. */ 1890 sd->state = sd_transfer_state; 1891 } 1892 break; 1893 1894 case 56: /* CMD56: GEN_CMD */ 1895 sd->data[sd->data_offset ++] = value; 1896 if (sd->data_offset >= sd->blk_len) { 1897 APP_WRITE_BLOCK(sd->data_start, sd->data_offset); 1898 sd->state = sd_transfer_state; 1899 } 1900 break; 1901 1902 default: 1903 qemu_log_mask(LOG_GUEST_ERROR, "sd_write_data: unknown command\n"); 1904 break; 1905 } 1906 } 1907 1908 #define SD_TUNING_BLOCK_SIZE 64 1909 1910 static const uint8_t sd_tuning_block_pattern[SD_TUNING_BLOCK_SIZE] = { 1911 /* See: Physical Layer Simplified Specification Version 3.01, Table 4-2 */ 1912 0xff, 0x0f, 0xff, 0x00, 0x0f, 0xfc, 0xc3, 0xcc, 1913 0xc3, 0x3c, 0xcc, 0xff, 0xfe, 0xff, 0xfe, 0xef, 1914 0xff, 0xdf, 0xff, 0xdd, 0xff, 0xfb, 0xff, 0xfb, 1915 0xbf, 0xff, 0x7f, 0xff, 0x77, 0xf7, 0xbd, 0xef, 1916 0xff, 0xf0, 0xff, 0xf0, 0x0f, 0xfc, 0xcc, 0x3c, 1917 0xcc, 0x33, 0xcc, 0xcf, 0xff, 0xef, 0xff, 0xee, 1918 0xff, 0xfd, 0xff, 0xfd, 0xdf, 0xff, 0xbf, 0xff, 1919 0xbb, 0xff, 0xf7, 0xff, 0xf7, 0x7f, 0x7b, 0xde, 1920 }; 1921 1922 uint8_t sd_read_data(SDState *sd) 1923 { 1924 /* TODO: Append CRCs */ 1925 uint8_t ret; 1926 int io_len; 1927 1928 if (!sd->blk || !blk_is_inserted(sd->blk) || !sd->enable) 1929 return 0x00; 1930 1931 if (sd->state != sd_sendingdata_state) { 1932 qemu_log_mask(LOG_GUEST_ERROR, 1933 "sd_read_data: not in Sending-Data state\n"); 1934 return 0x00; 1935 } 1936 1937 if (sd->card_status & (ADDRESS_ERROR | WP_VIOLATION)) 1938 return 0x00; 1939 1940 io_len = (sd->ocr & (1 << 30)) ? 512 : sd->blk_len; 1941 1942 trace_sdcard_read_data(sd->proto_name, 1943 sd_acmd_name(sd->current_cmd), 1944 sd->current_cmd, io_len); 1945 switch (sd->current_cmd) { 1946 case 6: /* CMD6: SWITCH_FUNCTION */ 1947 ret = sd->data[sd->data_offset ++]; 1948 1949 if (sd->data_offset >= 64) 1950 sd->state = sd_transfer_state; 1951 break; 1952 1953 case 9: /* CMD9: SEND_CSD */ 1954 case 10: /* CMD10: SEND_CID */ 1955 ret = sd->data[sd->data_offset ++]; 1956 1957 if (sd->data_offset >= 16) 1958 sd->state = sd_transfer_state; 1959 break; 1960 1961 case 13: /* ACMD13: SD_STATUS */ 1962 ret = sd->sd_status[sd->data_offset ++]; 1963 1964 if (sd->data_offset >= sizeof(sd->sd_status)) 1965 sd->state = sd_transfer_state; 1966 break; 1967 1968 case 17: /* CMD17: READ_SINGLE_BLOCK */ 1969 if (sd->data_offset == 0) 1970 BLK_READ_BLOCK(sd->data_start, io_len); 1971 ret = sd->data[sd->data_offset ++]; 1972 1973 if (sd->data_offset >= io_len) 1974 sd->state = sd_transfer_state; 1975 break; 1976 1977 case 18: /* CMD18: READ_MULTIPLE_BLOCK */ 1978 if (sd->data_offset == 0) { 1979 if (sd->data_start + io_len > sd->size) { 1980 sd->card_status |= ADDRESS_ERROR; 1981 return 0x00; 1982 } 1983 BLK_READ_BLOCK(sd->data_start, io_len); 1984 } 1985 ret = sd->data[sd->data_offset ++]; 1986 1987 if (sd->data_offset >= io_len) { 1988 sd->data_start += io_len; 1989 sd->data_offset = 0; 1990 1991 if (sd->multi_blk_cnt != 0) { 1992 if (--sd->multi_blk_cnt == 0) { 1993 /* Stop! */ 1994 sd->state = sd_transfer_state; 1995 break; 1996 } 1997 } 1998 } 1999 break; 2000 2001 case 19: /* CMD19: SEND_TUNING_BLOCK (SD) */ 2002 if (sd->data_offset >= SD_TUNING_BLOCK_SIZE - 1) { 2003 sd->state = sd_transfer_state; 2004 } 2005 ret = sd_tuning_block_pattern[sd->data_offset++]; 2006 break; 2007 2008 case 22: /* ACMD22: SEND_NUM_WR_BLOCKS */ 2009 ret = sd->data[sd->data_offset ++]; 2010 2011 if (sd->data_offset >= 4) 2012 sd->state = sd_transfer_state; 2013 break; 2014 2015 case 30: /* CMD30: SEND_WRITE_PROT */ 2016 ret = sd->data[sd->data_offset ++]; 2017 2018 if (sd->data_offset >= 4) 2019 sd->state = sd_transfer_state; 2020 break; 2021 2022 case 51: /* ACMD51: SEND_SCR */ 2023 ret = sd->scr[sd->data_offset ++]; 2024 2025 if (sd->data_offset >= sizeof(sd->scr)) 2026 sd->state = sd_transfer_state; 2027 break; 2028 2029 case 56: /* CMD56: GEN_CMD */ 2030 if (sd->data_offset == 0) 2031 APP_READ_BLOCK(sd->data_start, sd->blk_len); 2032 ret = sd->data[sd->data_offset ++]; 2033 2034 if (sd->data_offset >= sd->blk_len) 2035 sd->state = sd_transfer_state; 2036 break; 2037 2038 default: 2039 qemu_log_mask(LOG_GUEST_ERROR, "sd_read_data: unknown command\n"); 2040 return 0x00; 2041 } 2042 2043 return ret; 2044 } 2045 2046 bool sd_data_ready(SDState *sd) 2047 { 2048 return sd->state == sd_sendingdata_state; 2049 } 2050 2051 void sd_enable(SDState *sd, bool enable) 2052 { 2053 sd->enable = enable; 2054 } 2055 2056 static void sd_instance_init(Object *obj) 2057 { 2058 SDState *sd = SD_CARD(obj); 2059 2060 sd->enable = true; 2061 sd->ocr_power_timer = timer_new_ns(QEMU_CLOCK_VIRTUAL, sd_ocr_powerup, sd); 2062 } 2063 2064 static void sd_instance_finalize(Object *obj) 2065 { 2066 SDState *sd = SD_CARD(obj); 2067 2068 timer_del(sd->ocr_power_timer); 2069 timer_free(sd->ocr_power_timer); 2070 } 2071 2072 static void sd_realize(DeviceState *dev, Error **errp) 2073 { 2074 SDState *sd = SD_CARD(dev); 2075 int ret; 2076 2077 sd->proto_name = sd->spi ? "SPI" : "SD"; 2078 2079 switch (sd->spec_version) { 2080 case SD_PHY_SPECv1_10_VERS 2081 ... SD_PHY_SPECv3_01_VERS: 2082 break; 2083 default: 2084 error_setg(errp, "Invalid SD card Spec version: %u", sd->spec_version); 2085 return; 2086 } 2087 2088 if (sd->blk && blk_is_read_only(sd->blk)) { 2089 error_setg(errp, "Cannot use read-only drive as SD card"); 2090 return; 2091 } 2092 2093 if (sd->blk) { 2094 ret = blk_set_perm(sd->blk, BLK_PERM_CONSISTENT_READ | BLK_PERM_WRITE, 2095 BLK_PERM_ALL, errp); 2096 if (ret < 0) { 2097 return; 2098 } 2099 blk_set_dev_ops(sd->blk, &sd_block_ops, sd); 2100 } 2101 } 2102 2103 static Property sd_properties[] = { 2104 DEFINE_PROP_UINT8("spec_version", SDState, 2105 spec_version, SD_PHY_SPECv2_00_VERS), 2106 DEFINE_PROP_DRIVE("drive", SDState, blk), 2107 /* We do not model the chip select pin, so allow the board to select 2108 * whether card should be in SSI or MMC/SD mode. It is also up to the 2109 * board to ensure that ssi transfers only occur when the chip select 2110 * is asserted. */ 2111 DEFINE_PROP_BOOL("spi", SDState, spi, false), 2112 DEFINE_PROP_END_OF_LIST() 2113 }; 2114 2115 static void sd_class_init(ObjectClass *klass, void *data) 2116 { 2117 DeviceClass *dc = DEVICE_CLASS(klass); 2118 SDCardClass *sc = SD_CARD_CLASS(klass); 2119 2120 dc->realize = sd_realize; 2121 dc->props = sd_properties; 2122 dc->vmsd = &sd_vmstate; 2123 dc->reset = sd_reset; 2124 dc->bus_type = TYPE_SD_BUS; 2125 set_bit(DEVICE_CATEGORY_STORAGE, dc->categories); 2126 2127 sc->set_voltage = sd_set_voltage; 2128 sc->get_dat_lines = sd_get_dat_lines; 2129 sc->get_cmd_line = sd_get_cmd_line; 2130 sc->do_command = sd_do_command; 2131 sc->write_data = sd_write_data; 2132 sc->read_data = sd_read_data; 2133 sc->data_ready = sd_data_ready; 2134 sc->enable = sd_enable; 2135 sc->get_inserted = sd_get_inserted; 2136 sc->get_readonly = sd_get_readonly; 2137 } 2138 2139 static const TypeInfo sd_info = { 2140 .name = TYPE_SD_CARD, 2141 .parent = TYPE_DEVICE, 2142 .instance_size = sizeof(SDState), 2143 .class_size = sizeof(SDCardClass), 2144 .class_init = sd_class_init, 2145 .instance_init = sd_instance_init, 2146 .instance_finalize = sd_instance_finalize, 2147 }; 2148 2149 static void sd_register_types(void) 2150 { 2151 type_register_static(&sd_info); 2152 } 2153 2154 type_init(sd_register_types) 2155