1 /* 2 * Arm PrimeCell PL181 MultiMedia Card Interface 3 * 4 * Copyright (c) 2007 CodeSourcery. 5 * Written by Paul Brook 6 * 7 * This code is licensed under the GPL. 8 */ 9 10 #include "sysemu/block-backend.h" 11 #include "sysemu/blockdev.h" 12 #include "hw/sysbus.h" 13 #include "hw/sd.h" 14 15 //#define DEBUG_PL181 1 16 17 #ifdef DEBUG_PL181 18 #define DPRINTF(fmt, ...) \ 19 do { printf("pl181: " fmt , ## __VA_ARGS__); } while (0) 20 #else 21 #define DPRINTF(fmt, ...) do {} while(0) 22 #endif 23 24 #define PL181_FIFO_LEN 16 25 26 #define TYPE_PL181 "pl181" 27 #define PL181(obj) OBJECT_CHECK(PL181State, (obj), TYPE_PL181) 28 29 typedef struct PL181State { 30 SysBusDevice parent_obj; 31 32 MemoryRegion iomem; 33 SDState *card; 34 uint32_t clock; 35 uint32_t power; 36 uint32_t cmdarg; 37 uint32_t cmd; 38 uint32_t datatimer; 39 uint32_t datalength; 40 uint32_t respcmd; 41 uint32_t response[4]; 42 uint32_t datactrl; 43 uint32_t datacnt; 44 uint32_t status; 45 uint32_t mask[2]; 46 int32_t fifo_pos; 47 int32_t fifo_len; 48 /* The linux 2.6.21 driver is buggy, and misbehaves if new data arrives 49 while it is reading the FIFO. We hack around this be defering 50 subsequent transfers until after the driver polls the status word. 51 http://www.arm.linux.org.uk/developer/patches/viewpatch.php?id=4446/1 52 */ 53 int32_t linux_hack; 54 uint32_t fifo[PL181_FIFO_LEN]; 55 qemu_irq irq[2]; 56 /* GPIO outputs for 'card is readonly' and 'card inserted' */ 57 qemu_irq cardstatus[2]; 58 } PL181State; 59 60 static const VMStateDescription vmstate_pl181 = { 61 .name = "pl181", 62 .version_id = 1, 63 .minimum_version_id = 1, 64 .fields = (VMStateField[]) { 65 VMSTATE_UINT32(clock, PL181State), 66 VMSTATE_UINT32(power, PL181State), 67 VMSTATE_UINT32(cmdarg, PL181State), 68 VMSTATE_UINT32(cmd, PL181State), 69 VMSTATE_UINT32(datatimer, PL181State), 70 VMSTATE_UINT32(datalength, PL181State), 71 VMSTATE_UINT32(respcmd, PL181State), 72 VMSTATE_UINT32_ARRAY(response, PL181State, 4), 73 VMSTATE_UINT32(datactrl, PL181State), 74 VMSTATE_UINT32(datacnt, PL181State), 75 VMSTATE_UINT32(status, PL181State), 76 VMSTATE_UINT32_ARRAY(mask, PL181State, 2), 77 VMSTATE_INT32(fifo_pos, PL181State), 78 VMSTATE_INT32(fifo_len, PL181State), 79 VMSTATE_INT32(linux_hack, PL181State), 80 VMSTATE_UINT32_ARRAY(fifo, PL181State, PL181_FIFO_LEN), 81 VMSTATE_END_OF_LIST() 82 } 83 }; 84 85 #define PL181_CMD_INDEX 0x3f 86 #define PL181_CMD_RESPONSE (1 << 6) 87 #define PL181_CMD_LONGRESP (1 << 7) 88 #define PL181_CMD_INTERRUPT (1 << 8) 89 #define PL181_CMD_PENDING (1 << 9) 90 #define PL181_CMD_ENABLE (1 << 10) 91 92 #define PL181_DATA_ENABLE (1 << 0) 93 #define PL181_DATA_DIRECTION (1 << 1) 94 #define PL181_DATA_MODE (1 << 2) 95 #define PL181_DATA_DMAENABLE (1 << 3) 96 97 #define PL181_STATUS_CMDCRCFAIL (1 << 0) 98 #define PL181_STATUS_DATACRCFAIL (1 << 1) 99 #define PL181_STATUS_CMDTIMEOUT (1 << 2) 100 #define PL181_STATUS_DATATIMEOUT (1 << 3) 101 #define PL181_STATUS_TXUNDERRUN (1 << 4) 102 #define PL181_STATUS_RXOVERRUN (1 << 5) 103 #define PL181_STATUS_CMDRESPEND (1 << 6) 104 #define PL181_STATUS_CMDSENT (1 << 7) 105 #define PL181_STATUS_DATAEND (1 << 8) 106 #define PL181_STATUS_DATABLOCKEND (1 << 10) 107 #define PL181_STATUS_CMDACTIVE (1 << 11) 108 #define PL181_STATUS_TXACTIVE (1 << 12) 109 #define PL181_STATUS_RXACTIVE (1 << 13) 110 #define PL181_STATUS_TXFIFOHALFEMPTY (1 << 14) 111 #define PL181_STATUS_RXFIFOHALFFULL (1 << 15) 112 #define PL181_STATUS_TXFIFOFULL (1 << 16) 113 #define PL181_STATUS_RXFIFOFULL (1 << 17) 114 #define PL181_STATUS_TXFIFOEMPTY (1 << 18) 115 #define PL181_STATUS_RXFIFOEMPTY (1 << 19) 116 #define PL181_STATUS_TXDATAAVLBL (1 << 20) 117 #define PL181_STATUS_RXDATAAVLBL (1 << 21) 118 119 #define PL181_STATUS_TX_FIFO (PL181_STATUS_TXACTIVE \ 120 |PL181_STATUS_TXFIFOHALFEMPTY \ 121 |PL181_STATUS_TXFIFOFULL \ 122 |PL181_STATUS_TXFIFOEMPTY \ 123 |PL181_STATUS_TXDATAAVLBL) 124 #define PL181_STATUS_RX_FIFO (PL181_STATUS_RXACTIVE \ 125 |PL181_STATUS_RXFIFOHALFFULL \ 126 |PL181_STATUS_RXFIFOFULL \ 127 |PL181_STATUS_RXFIFOEMPTY \ 128 |PL181_STATUS_RXDATAAVLBL) 129 130 static const unsigned char pl181_id[] = 131 { 0x81, 0x11, 0x04, 0x00, 0x0d, 0xf0, 0x05, 0xb1 }; 132 133 static void pl181_update(PL181State *s) 134 { 135 int i; 136 for (i = 0; i < 2; i++) { 137 qemu_set_irq(s->irq[i], (s->status & s->mask[i]) != 0); 138 } 139 } 140 141 static void pl181_fifo_push(PL181State *s, uint32_t value) 142 { 143 int n; 144 145 if (s->fifo_len == PL181_FIFO_LEN) { 146 fprintf(stderr, "pl181: FIFO overflow\n"); 147 return; 148 } 149 n = (s->fifo_pos + s->fifo_len) & (PL181_FIFO_LEN - 1); 150 s->fifo_len++; 151 s->fifo[n] = value; 152 DPRINTF("FIFO push %08x\n", (int)value); 153 } 154 155 static uint32_t pl181_fifo_pop(PL181State *s) 156 { 157 uint32_t value; 158 159 if (s->fifo_len == 0) { 160 fprintf(stderr, "pl181: FIFO underflow\n"); 161 return 0; 162 } 163 value = s->fifo[s->fifo_pos]; 164 s->fifo_len--; 165 s->fifo_pos = (s->fifo_pos + 1) & (PL181_FIFO_LEN - 1); 166 DPRINTF("FIFO pop %08x\n", (int)value); 167 return value; 168 } 169 170 static void pl181_send_command(PL181State *s) 171 { 172 SDRequest request; 173 uint8_t response[16]; 174 int rlen; 175 176 request.cmd = s->cmd & PL181_CMD_INDEX; 177 request.arg = s->cmdarg; 178 DPRINTF("Command %d %08x\n", request.cmd, request.arg); 179 rlen = sd_do_command(s->card, &request, response); 180 if (rlen < 0) 181 goto error; 182 if (s->cmd & PL181_CMD_RESPONSE) { 183 #define RWORD(n) (((uint32_t)response[n] << 24) | (response[n + 1] << 16) \ 184 | (response[n + 2] << 8) | response[n + 3]) 185 if (rlen == 0 || (rlen == 4 && (s->cmd & PL181_CMD_LONGRESP))) 186 goto error; 187 if (rlen != 4 && rlen != 16) 188 goto error; 189 s->response[0] = RWORD(0); 190 if (rlen == 4) { 191 s->response[1] = s->response[2] = s->response[3] = 0; 192 } else { 193 s->response[1] = RWORD(4); 194 s->response[2] = RWORD(8); 195 s->response[3] = RWORD(12) & ~1; 196 } 197 DPRINTF("Response received\n"); 198 s->status |= PL181_STATUS_CMDRESPEND; 199 #undef RWORD 200 } else { 201 DPRINTF("Command sent\n"); 202 s->status |= PL181_STATUS_CMDSENT; 203 } 204 return; 205 206 error: 207 DPRINTF("Timeout\n"); 208 s->status |= PL181_STATUS_CMDTIMEOUT; 209 } 210 211 /* Transfer data between the card and the FIFO. This is complicated by 212 the FIFO holding 32-bit words and the card taking data in single byte 213 chunks. FIFO bytes are transferred in little-endian order. */ 214 215 static void pl181_fifo_run(PL181State *s) 216 { 217 uint32_t bits; 218 uint32_t value = 0; 219 int n; 220 int is_read; 221 222 is_read = (s->datactrl & PL181_DATA_DIRECTION) != 0; 223 if (s->datacnt != 0 && (!is_read || sd_data_ready(s->card)) 224 && !s->linux_hack) { 225 if (is_read) { 226 n = 0; 227 while (s->datacnt && s->fifo_len < PL181_FIFO_LEN) { 228 value |= (uint32_t)sd_read_data(s->card) << (n * 8); 229 s->datacnt--; 230 n++; 231 if (n == 4) { 232 pl181_fifo_push(s, value); 233 n = 0; 234 value = 0; 235 } 236 } 237 if (n != 0) { 238 pl181_fifo_push(s, value); 239 } 240 } else { /* write */ 241 n = 0; 242 while (s->datacnt > 0 && (s->fifo_len > 0 || n > 0)) { 243 if (n == 0) { 244 value = pl181_fifo_pop(s); 245 n = 4; 246 } 247 n--; 248 s->datacnt--; 249 sd_write_data(s->card, value & 0xff); 250 value >>= 8; 251 } 252 } 253 } 254 s->status &= ~(PL181_STATUS_RX_FIFO | PL181_STATUS_TX_FIFO); 255 if (s->datacnt == 0) { 256 s->status |= PL181_STATUS_DATAEND; 257 /* HACK: */ 258 s->status |= PL181_STATUS_DATABLOCKEND; 259 DPRINTF("Transfer Complete\n"); 260 } 261 if (s->datacnt == 0 && s->fifo_len == 0) { 262 s->datactrl &= ~PL181_DATA_ENABLE; 263 DPRINTF("Data engine idle\n"); 264 } else { 265 /* Update FIFO bits. */ 266 bits = PL181_STATUS_TXACTIVE | PL181_STATUS_RXACTIVE; 267 if (s->fifo_len == 0) { 268 bits |= PL181_STATUS_TXFIFOEMPTY; 269 bits |= PL181_STATUS_RXFIFOEMPTY; 270 } else { 271 bits |= PL181_STATUS_TXDATAAVLBL; 272 bits |= PL181_STATUS_RXDATAAVLBL; 273 } 274 if (s->fifo_len == 16) { 275 bits |= PL181_STATUS_TXFIFOFULL; 276 bits |= PL181_STATUS_RXFIFOFULL; 277 } 278 if (s->fifo_len <= 8) { 279 bits |= PL181_STATUS_TXFIFOHALFEMPTY; 280 } 281 if (s->fifo_len >= 8) { 282 bits |= PL181_STATUS_RXFIFOHALFFULL; 283 } 284 if (s->datactrl & PL181_DATA_DIRECTION) { 285 bits &= PL181_STATUS_RX_FIFO; 286 } else { 287 bits &= PL181_STATUS_TX_FIFO; 288 } 289 s->status |= bits; 290 } 291 } 292 293 static uint64_t pl181_read(void *opaque, hwaddr offset, 294 unsigned size) 295 { 296 PL181State *s = (PL181State *)opaque; 297 uint32_t tmp; 298 299 if (offset >= 0xfe0 && offset < 0x1000) { 300 return pl181_id[(offset - 0xfe0) >> 2]; 301 } 302 switch (offset) { 303 case 0x00: /* Power */ 304 return s->power; 305 case 0x04: /* Clock */ 306 return s->clock; 307 case 0x08: /* Argument */ 308 return s->cmdarg; 309 case 0x0c: /* Command */ 310 return s->cmd; 311 case 0x10: /* RespCmd */ 312 return s->respcmd; 313 case 0x14: /* Response0 */ 314 return s->response[0]; 315 case 0x18: /* Response1 */ 316 return s->response[1]; 317 case 0x1c: /* Response2 */ 318 return s->response[2]; 319 case 0x20: /* Response3 */ 320 return s->response[3]; 321 case 0x24: /* DataTimer */ 322 return s->datatimer; 323 case 0x28: /* DataLength */ 324 return s->datalength; 325 case 0x2c: /* DataCtrl */ 326 return s->datactrl; 327 case 0x30: /* DataCnt */ 328 return s->datacnt; 329 case 0x34: /* Status */ 330 tmp = s->status; 331 if (s->linux_hack) { 332 s->linux_hack = 0; 333 pl181_fifo_run(s); 334 pl181_update(s); 335 } 336 return tmp; 337 case 0x3c: /* Mask0 */ 338 return s->mask[0]; 339 case 0x40: /* Mask1 */ 340 return s->mask[1]; 341 case 0x48: /* FifoCnt */ 342 /* The documentation is somewhat vague about exactly what FifoCnt 343 does. On real hardware it appears to be when decrememnted 344 when a word is transferred between the FIFO and the serial 345 data engine. DataCnt is decremented after each byte is 346 transferred between the serial engine and the card. 347 We don't emulate this level of detail, so both can be the same. */ 348 tmp = (s->datacnt + 3) >> 2; 349 if (s->linux_hack) { 350 s->linux_hack = 0; 351 pl181_fifo_run(s); 352 pl181_update(s); 353 } 354 return tmp; 355 case 0x80: case 0x84: case 0x88: case 0x8c: /* FifoData */ 356 case 0x90: case 0x94: case 0x98: case 0x9c: 357 case 0xa0: case 0xa4: case 0xa8: case 0xac: 358 case 0xb0: case 0xb4: case 0xb8: case 0xbc: 359 if (s->fifo_len == 0) { 360 qemu_log_mask(LOG_GUEST_ERROR, "pl181: Unexpected FIFO read\n"); 361 return 0; 362 } else { 363 uint32_t value; 364 value = pl181_fifo_pop(s); 365 s->linux_hack = 1; 366 pl181_fifo_run(s); 367 pl181_update(s); 368 return value; 369 } 370 default: 371 qemu_log_mask(LOG_GUEST_ERROR, 372 "pl181_read: Bad offset %x\n", (int)offset); 373 return 0; 374 } 375 } 376 377 static void pl181_write(void *opaque, hwaddr offset, 378 uint64_t value, unsigned size) 379 { 380 PL181State *s = (PL181State *)opaque; 381 382 switch (offset) { 383 case 0x00: /* Power */ 384 s->power = value & 0xff; 385 break; 386 case 0x04: /* Clock */ 387 s->clock = value & 0xff; 388 break; 389 case 0x08: /* Argument */ 390 s->cmdarg = value; 391 break; 392 case 0x0c: /* Command */ 393 s->cmd = value; 394 if (s->cmd & PL181_CMD_ENABLE) { 395 if (s->cmd & PL181_CMD_INTERRUPT) { 396 qemu_log_mask(LOG_UNIMP, 397 "pl181: Interrupt mode not implemented\n"); 398 } if (s->cmd & PL181_CMD_PENDING) { 399 qemu_log_mask(LOG_UNIMP, 400 "pl181: Pending commands not implemented\n"); 401 } else { 402 pl181_send_command(s); 403 pl181_fifo_run(s); 404 } 405 /* The command has completed one way or the other. */ 406 s->cmd &= ~PL181_CMD_ENABLE; 407 } 408 break; 409 case 0x24: /* DataTimer */ 410 s->datatimer = value; 411 break; 412 case 0x28: /* DataLength */ 413 s->datalength = value & 0xffff; 414 break; 415 case 0x2c: /* DataCtrl */ 416 s->datactrl = value & 0xff; 417 if (value & PL181_DATA_ENABLE) { 418 s->datacnt = s->datalength; 419 pl181_fifo_run(s); 420 } 421 break; 422 case 0x38: /* Clear */ 423 s->status &= ~(value & 0x7ff); 424 break; 425 case 0x3c: /* Mask0 */ 426 s->mask[0] = value; 427 break; 428 case 0x40: /* Mask1 */ 429 s->mask[1] = value; 430 break; 431 case 0x80: case 0x84: case 0x88: case 0x8c: /* FifoData */ 432 case 0x90: case 0x94: case 0x98: case 0x9c: 433 case 0xa0: case 0xa4: case 0xa8: case 0xac: 434 case 0xb0: case 0xb4: case 0xb8: case 0xbc: 435 if (s->datacnt == 0) { 436 qemu_log_mask(LOG_GUEST_ERROR, "pl181: Unexpected FIFO write\n"); 437 } else { 438 pl181_fifo_push(s, value); 439 pl181_fifo_run(s); 440 } 441 break; 442 default: 443 qemu_log_mask(LOG_GUEST_ERROR, 444 "pl181_write: Bad offset %x\n", (int)offset); 445 } 446 pl181_update(s); 447 } 448 449 static const MemoryRegionOps pl181_ops = { 450 .read = pl181_read, 451 .write = pl181_write, 452 .endianness = DEVICE_NATIVE_ENDIAN, 453 }; 454 455 static void pl181_reset(DeviceState *d) 456 { 457 PL181State *s = PL181(d); 458 459 s->power = 0; 460 s->cmdarg = 0; 461 s->cmd = 0; 462 s->datatimer = 0; 463 s->datalength = 0; 464 s->respcmd = 0; 465 s->response[0] = 0; 466 s->response[1] = 0; 467 s->response[2] = 0; 468 s->response[3] = 0; 469 s->datatimer = 0; 470 s->datalength = 0; 471 s->datactrl = 0; 472 s->datacnt = 0; 473 s->status = 0; 474 s->linux_hack = 0; 475 s->mask[0] = 0; 476 s->mask[1] = 0; 477 478 /* We can assume our GPIO outputs have been wired up now */ 479 sd_set_cb(s->card, s->cardstatus[0], s->cardstatus[1]); 480 } 481 482 static int pl181_init(SysBusDevice *sbd) 483 { 484 DeviceState *dev = DEVICE(sbd); 485 PL181State *s = PL181(dev); 486 DriveInfo *dinfo; 487 488 memory_region_init_io(&s->iomem, OBJECT(s), &pl181_ops, s, "pl181", 0x1000); 489 sysbus_init_mmio(sbd, &s->iomem); 490 sysbus_init_irq(sbd, &s->irq[0]); 491 sysbus_init_irq(sbd, &s->irq[1]); 492 qdev_init_gpio_out(dev, s->cardstatus, 2); 493 /* FIXME use a qdev drive property instead of drive_get_next() */ 494 dinfo = drive_get_next(IF_SD); 495 s->card = sd_init(dinfo ? blk_by_legacy_dinfo(dinfo) : NULL, false); 496 if (s->card == NULL) { 497 return -1; 498 } 499 500 return 0; 501 } 502 503 static void pl181_class_init(ObjectClass *klass, void *data) 504 { 505 SysBusDeviceClass *sdc = SYS_BUS_DEVICE_CLASS(klass); 506 DeviceClass *k = DEVICE_CLASS(klass); 507 508 sdc->init = pl181_init; 509 k->vmsd = &vmstate_pl181; 510 k->reset = pl181_reset; 511 /* Reason: init() method uses drive_get_next() */ 512 k->cannot_instantiate_with_device_add_yet = true; 513 } 514 515 static const TypeInfo pl181_info = { 516 .name = TYPE_PL181, 517 .parent = TYPE_SYS_BUS_DEVICE, 518 .instance_size = sizeof(PL181State), 519 .class_init = pl181_class_init, 520 }; 521 522 static void pl181_register_types(void) 523 { 524 type_register_static(&pl181_info); 525 } 526 527 type_init(pl181_register_types) 528