1 /* 2 * QEMU m68k Macintosh VIA device support 3 * 4 * Copyright (c) 2011-2018 Laurent Vivier 5 * Copyright (c) 2018 Mark Cave-Ayland 6 * 7 * Some parts from hw/misc/macio/cuda.c 8 * 9 * Copyright (c) 2004-2007 Fabrice Bellard 10 * Copyright (c) 2007 Jocelyn Mayer 11 * 12 * some parts from linux-2.6.29, arch/m68k/include/asm/mac_via.h 13 * 14 * This work is licensed under the terms of the GNU GPL, version 2 or later. 15 * See the COPYING file in the top-level directory. 16 */ 17 18 #include "qemu/osdep.h" 19 #include "qemu-common.h" 20 #include "migration/vmstate.h" 21 #include "hw/sysbus.h" 22 #include "hw/irq.h" 23 #include "qemu/timer.h" 24 #include "hw/misc/mac_via.h" 25 #include "hw/misc/mos6522.h" 26 #include "hw/input/adb.h" 27 #include "sysemu/runstate.h" 28 #include "qapi/error.h" 29 #include "qemu/cutils.h" 30 #include "hw/qdev-properties.h" 31 #include "hw/qdev-properties-system.h" 32 #include "sysemu/block-backend.h" 33 #include "trace.h" 34 #include "qemu/log.h" 35 36 /* 37 * VIAs: There are two in every machine 38 */ 39 40 /* 41 * Not all of these are true post MacII I think. 42 * CSA: probably the ones CHRP marks as 'unused' change purposes 43 * when the IWM becomes the SWIM. 44 * http://www.rs6000.ibm.com/resource/technology/chrpio/via5.mak.html 45 * ftp://ftp.austin.ibm.com/pub/technology/spec/chrp/inwork/CHRP_IORef_1.0.pdf 46 * 47 * also, http://developer.apple.com/technotes/hw/hw_09.html claims the 48 * following changes for IIfx: 49 * VIA1A_vSccWrReq not available and that VIA1A_vSync has moved to an IOP. 50 * Also, "All of the functionality of VIA2 has been moved to other chips". 51 */ 52 53 #define VIA1A_vSccWrReq 0x80 /* 54 * SCC write. (input) 55 * [CHRP] SCC WREQ: Reflects the state of the 56 * Wait/Request pins from the SCC. 57 * [Macintosh Family Hardware] 58 * as CHRP on SE/30,II,IIx,IIcx,IIci. 59 * on IIfx, "0 means an active request" 60 */ 61 #define VIA1A_vRev8 0x40 /* 62 * Revision 8 board ??? 63 * [CHRP] En WaitReqB: Lets the WaitReq_L 64 * signal from port B of the SCC appear on 65 * the PA7 input pin. Output. 66 * [Macintosh Family] On the SE/30, this 67 * is the bit to flip screen buffers. 68 * 0=alternate, 1=main. 69 * on II,IIx,IIcx,IIci,IIfx this is a bit 70 * for Rev ID. 0=II,IIx, 1=IIcx,IIci,IIfx 71 */ 72 #define VIA1A_vHeadSel 0x20 /* 73 * Head select for IWM. 74 * [CHRP] unused. 75 * [Macintosh Family] "Floppy disk 76 * state-control line SEL" on all but IIfx 77 */ 78 #define VIA1A_vOverlay 0x10 /* 79 * [Macintosh Family] On SE/30,II,IIx,IIcx 80 * this bit enables the "Overlay" address 81 * map in the address decoders as it is on 82 * reset for mapping the ROM over the reset 83 * vector. 1=use overlay map. 84 * On the IIci,IIfx it is another bit of the 85 * CPU ID: 0=normal IIci, 1=IIci with parity 86 * feature or IIfx. 87 * [CHRP] En WaitReqA: Lets the WaitReq_L 88 * signal from port A of the SCC appear 89 * on the PA7 input pin (CHRP). Output. 90 * [MkLinux] "Drive Select" 91 * (with 0x20 being 'disk head select') 92 */ 93 #define VIA1A_vSync 0x08 /* 94 * [CHRP] Sync Modem: modem clock select: 95 * 1: select the external serial clock to 96 * drive the SCC's /RTxCA pin. 97 * 0: Select the 3.6864MHz clock to drive 98 * the SCC cell. 99 * [Macintosh Family] Correct on all but IIfx 100 */ 101 102 /* 103 * Macintosh Family Hardware sez: bits 0-2 of VIA1A are volume control 104 * on Macs which had the PWM sound hardware. Reserved on newer models. 105 * On IIci,IIfx, bits 1-2 are the rest of the CPU ID: 106 * bit 2: 1=IIci, 0=IIfx 107 * bit 1: 1 on both IIci and IIfx. 108 * MkLinux sez bit 0 is 'burnin flag' in this case. 109 * CHRP sez: VIA1A bits 0-2 and 5 are 'unused': if programmed as 110 * inputs, these bits will read 0. 111 */ 112 #define VIA1A_vVolume 0x07 /* Audio volume mask for PWM */ 113 #define VIA1A_CPUID0 0x02 /* CPU id bit 0 on RBV, others */ 114 #define VIA1A_CPUID1 0x04 /* CPU id bit 0 on RBV, others */ 115 #define VIA1A_CPUID2 0x10 /* CPU id bit 0 on RBV, others */ 116 #define VIA1A_CPUID3 0x40 /* CPU id bit 0 on RBV, others */ 117 118 /* 119 * Info on VIA1B is from Macintosh Family Hardware & MkLinux. 120 * CHRP offers no info. 121 */ 122 #define VIA1B_vSound 0x80 /* 123 * Sound enable (for compatibility with 124 * PWM hardware) 0=enabled. 125 * Also, on IIci w/parity, shows parity error 126 * 0=error, 1=OK. 127 */ 128 #define VIA1B_vMystery 0x40 /* 129 * On IIci, parity enable. 0=enabled,1=disabled 130 * On SE/30, vertical sync interrupt enable. 131 * 0=enabled. This vSync interrupt shows up 132 * as a slot $E interrupt. 133 */ 134 #define VIA1B_vADBS2 0x20 /* ADB state input bit 1 (unused on IIfx) */ 135 #define VIA1B_vADBS1 0x10 /* ADB state input bit 0 (unused on IIfx) */ 136 #define VIA1B_vADBInt 0x08 /* ADB interrupt 0=interrupt (unused on IIfx)*/ 137 #define VIA1B_vRTCEnb 0x04 /* Enable Real time clock. 0=enabled. */ 138 #define VIA1B_vRTCClk 0x02 /* Real time clock serial-clock line. */ 139 #define VIA1B_vRTCData 0x01 /* Real time clock serial-data line. */ 140 141 /* 142 * VIA2 A register is the interrupt lines raised off the nubus 143 * slots. 144 * The below info is from 'Macintosh Family Hardware.' 145 * MkLinux calls the 'IIci internal video IRQ' below the 'RBV slot 0 irq.' 146 * It also notes that the slot $9 IRQ is the 'Ethernet IRQ' and 147 * defines the 'Video IRQ' as 0x40 for the 'EVR' VIA work-alike. 148 * Perhaps OSS uses vRAM1 and vRAM2 for ADB. 149 */ 150 151 #define VIA2A_vRAM1 0x80 /* RAM size bit 1 (IIci: reserved) */ 152 #define VIA2A_vRAM0 0x40 /* RAM size bit 0 (IIci: internal video IRQ) */ 153 #define VIA2A_vIRQE 0x20 /* IRQ from slot $E */ 154 #define VIA2A_vIRQD 0x10 /* IRQ from slot $D */ 155 #define VIA2A_vIRQC 0x08 /* IRQ from slot $C */ 156 #define VIA2A_vIRQB 0x04 /* IRQ from slot $B */ 157 #define VIA2A_vIRQA 0x02 /* IRQ from slot $A */ 158 #define VIA2A_vIRQ9 0x01 /* IRQ from slot $9 */ 159 160 /* 161 * RAM size bits decoded as follows: 162 * bit1 bit0 size of ICs in bank A 163 * 0 0 256 kbit 164 * 0 1 1 Mbit 165 * 1 0 4 Mbit 166 * 1 1 16 Mbit 167 */ 168 169 /* 170 * Register B has the fun stuff in it 171 */ 172 173 #define VIA2B_vVBL 0x80 /* 174 * VBL output to VIA1 (60.15Hz) driven by 175 * timer T1. 176 * on IIci, parity test: 0=test mode. 177 * [MkLinux] RBV_PARODD: 1=odd,0=even. 178 */ 179 #define VIA2B_vSndJck 0x40 /* 180 * External sound jack status. 181 * 0=plug is inserted. On SE/30, always 0 182 */ 183 #define VIA2B_vTfr0 0x20 /* Transfer mode bit 0 ack from NuBus */ 184 #define VIA2B_vTfr1 0x10 /* Transfer mode bit 1 ack from NuBus */ 185 #define VIA2B_vMode32 0x08 /* 186 * 24/32bit switch - doubles as cache flush 187 * on II, AMU/PMMU control. 188 * if AMU, 0=24bit to 32bit translation 189 * if PMMU, 1=PMMU is accessing page table. 190 * on SE/30 tied low. 191 * on IIx,IIcx,IIfx, unused. 192 * on IIci/RBV, cache control. 0=flush cache. 193 */ 194 #define VIA2B_vPower 0x04 /* 195 * Power off, 0=shut off power. 196 * on SE/30 this signal sent to PDS card. 197 */ 198 #define VIA2B_vBusLk 0x02 /* 199 * Lock NuBus transactions, 0=locked. 200 * on SE/30 sent to PDS card. 201 */ 202 #define VIA2B_vCDis 0x01 /* 203 * Cache control. On IIci, 1=disable cache card 204 * on others, 0=disable processor's instruction 205 * and data caches. 206 */ 207 208 /* interrupt flags */ 209 210 #define IRQ_SET 0x80 211 212 /* common */ 213 214 #define VIA_IRQ_TIMER1 0x40 215 #define VIA_IRQ_TIMER2 0x20 216 217 /* 218 * Apple sez: http://developer.apple.com/technotes/ov/ov_04.html 219 * Another example of a valid function that has no ROM support is the use 220 * of the alternate video page for page-flipping animation. Since there 221 * is no ROM call to flip pages, it is necessary to go play with the 222 * right bit in the VIA chip (6522 Versatile Interface Adapter). 223 * [CSA: don't know which one this is, but it's one of 'em!] 224 */ 225 226 /* 227 * 6522 registers - see databook. 228 * CSA: Assignments for VIA1 confirmed from CHRP spec. 229 */ 230 231 /* partial address decode. 0xYYXX : XX part for RBV, YY part for VIA */ 232 /* Note: 15 VIA regs, 8 RBV regs */ 233 234 #define vBufB 0x0000 /* [VIA/RBV] Register B */ 235 #define vBufAH 0x0200 /* [VIA only] Buffer A, with handshake. DON'T USE! */ 236 #define vDirB 0x0400 /* [VIA only] Data Direction Register B. */ 237 #define vDirA 0x0600 /* [VIA only] Data Direction Register A. */ 238 #define vT1CL 0x0800 /* [VIA only] Timer one counter low. */ 239 #define vT1CH 0x0a00 /* [VIA only] Timer one counter high. */ 240 #define vT1LL 0x0c00 /* [VIA only] Timer one latches low. */ 241 #define vT1LH 0x0e00 /* [VIA only] Timer one latches high. */ 242 #define vT2CL 0x1000 /* [VIA only] Timer two counter low. */ 243 #define vT2CH 0x1200 /* [VIA only] Timer two counter high. */ 244 #define vSR 0x1400 /* [VIA only] Shift register. */ 245 #define vACR 0x1600 /* [VIA only] Auxilary control register. */ 246 #define vPCR 0x1800 /* [VIA only] Peripheral control register. */ 247 /* 248 * CHRP sez never ever to *write* this. 249 * Mac family says never to *change* this. 250 * In fact we need to initialize it once at start. 251 */ 252 #define vIFR 0x1a00 /* [VIA/RBV] Interrupt flag register. */ 253 #define vIER 0x1c00 /* [VIA/RBV] Interrupt enable register. */ 254 #define vBufA 0x1e00 /* [VIA/RBV] register A (no handshake) */ 255 256 /* from linux 2.6 drivers/macintosh/via-macii.c */ 257 258 /* Bits in ACR */ 259 260 #define VIA1ACR_vShiftCtrl 0x1c /* Shift register control bits */ 261 #define VIA1ACR_vShiftExtClk 0x0c /* Shift on external clock */ 262 #define VIA1ACR_vShiftOut 0x10 /* Shift out if 1 */ 263 264 /* 265 * Apple Macintosh Family Hardware Refenece 266 * Table 19-10 ADB transaction states 267 */ 268 269 #define ADB_STATE_NEW 0 270 #define ADB_STATE_EVEN 1 271 #define ADB_STATE_ODD 2 272 #define ADB_STATE_IDLE 3 273 274 #define VIA1B_vADB_StateMask (VIA1B_vADBS1 | VIA1B_vADBS2) 275 #define VIA1B_vADB_StateShift 4 276 277 #define VIA_TIMER_FREQ (783360) 278 #define VIA_ADB_POLL_FREQ 50 /* XXX: not real */ 279 280 /* 281 * Guide to the Macintosh Family Hardware ch. 12 "Displays" p. 401 gives the 282 * precise 60Hz interrupt frequency as ~60.15Hz with a period of 16625.8 us 283 */ 284 #define VIA_60HZ_TIMER_PERIOD_NS 16625800 285 286 /* VIA returns time offset from Jan 1, 1904, not 1970 */ 287 #define RTC_OFFSET 2082844800 288 289 enum { 290 REG_0, 291 REG_1, 292 REG_2, 293 REG_3, 294 REG_TEST, 295 REG_WPROTECT, 296 REG_PRAM_ADDR, 297 REG_PRAM_ADDR_LAST = REG_PRAM_ADDR + 19, 298 REG_PRAM_SECT, 299 REG_PRAM_SECT_LAST = REG_PRAM_SECT + 7, 300 REG_INVALID, 301 REG_EMPTY = 0xff, 302 }; 303 304 static void via1_sixty_hz_update(MOS6522Q800VIA1State *v1s) 305 { 306 /* 60 Hz irq */ 307 v1s->next_sixty_hz = (qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + 308 VIA_60HZ_TIMER_PERIOD_NS) / 309 VIA_60HZ_TIMER_PERIOD_NS * VIA_60HZ_TIMER_PERIOD_NS; 310 timer_mod(v1s->sixty_hz_timer, v1s->next_sixty_hz); 311 } 312 313 static void via1_one_second_update(MOS6522Q800VIA1State *v1s) 314 { 315 v1s->next_second = (qemu_clock_get_ms(QEMU_CLOCK_VIRTUAL) + 1000) / 316 1000 * 1000; 317 timer_mod(v1s->one_second_timer, v1s->next_second); 318 } 319 320 static void via1_sixty_hz(void *opaque) 321 { 322 MOS6522Q800VIA1State *v1s = opaque; 323 MOS6522State *s = MOS6522(v1s); 324 MOS6522DeviceClass *mdc = MOS6522_GET_CLASS(s); 325 326 s->ifr |= VIA1_IRQ_60HZ; 327 mdc->update_irq(s); 328 329 via1_sixty_hz_update(v1s); 330 } 331 332 static void via1_one_second(void *opaque) 333 { 334 MOS6522Q800VIA1State *v1s = opaque; 335 MOS6522State *s = MOS6522(v1s); 336 MOS6522DeviceClass *mdc = MOS6522_GET_CLASS(s); 337 338 s->ifr |= VIA1_IRQ_ONE_SECOND; 339 mdc->update_irq(s); 340 341 via1_one_second_update(v1s); 342 } 343 344 static void via1_irq_request(void *opaque, int irq, int level) 345 { 346 MOS6522Q800VIA1State *v1s = opaque; 347 MOS6522State *s = MOS6522(v1s); 348 MOS6522DeviceClass *mdc = MOS6522_GET_CLASS(s); 349 350 if (level) { 351 s->ifr |= 1 << irq; 352 } else { 353 s->ifr &= ~(1 << irq); 354 } 355 356 mdc->update_irq(s); 357 } 358 359 static void via2_irq_request(void *opaque, int irq, int level) 360 { 361 MOS6522Q800VIA2State *v2s = opaque; 362 MOS6522State *s = MOS6522(v2s); 363 MOS6522DeviceClass *mdc = MOS6522_GET_CLASS(s); 364 365 if (level) { 366 s->ifr |= 1 << irq; 367 } else { 368 s->ifr &= ~(1 << irq); 369 } 370 371 mdc->update_irq(s); 372 } 373 374 375 static void pram_update(MOS6522Q800VIA1State *v1s) 376 { 377 if (v1s->blk) { 378 if (blk_pwrite(v1s->blk, 0, v1s->PRAM, sizeof(v1s->PRAM), 0) < 0) { 379 qemu_log("pram_update: cannot write to file\n"); 380 } 381 } 382 } 383 384 /* 385 * RTC Commands 386 * 387 * Command byte Register addressed by the command 388 * 389 * z0000001 Seconds register 0 (lowest-order byte) 390 * z0000101 Seconds register 1 391 * z0001001 Seconds register 2 392 * z0001101 Seconds register 3 (highest-order byte) 393 * 00110001 Test register (write-only) 394 * 00110101 Write-Protect Register (write-only) 395 * z010aa01 RAM address 100aa ($10-$13) (first 20 bytes only) 396 * z1aaaa01 RAM address 0aaaa ($00-$0F) (first 20 bytes only) 397 * z0111aaa Extended memory designator and sector number 398 * 399 * For a read request, z=1, for a write z=0 400 * The letter a indicates bits whose value depend on what parameter 401 * RAM byte you want to address 402 */ 403 static int via1_rtc_compact_cmd(uint8_t value) 404 { 405 uint8_t read = value & 0x80; 406 407 value &= 0x7f; 408 409 /* the last 2 bits of a command byte must always be 0b01 ... */ 410 if ((value & 0x78) == 0x38) { 411 /* except for the extended memory designator */ 412 return read | (REG_PRAM_SECT + (value & 0x07)); 413 } 414 if ((value & 0x03) == 0x01) { 415 value >>= 2; 416 if ((value & 0x1c) == 0) { 417 /* seconds registers */ 418 return read | (REG_0 + (value & 0x03)); 419 } else if ((value == 0x0c) && !read) { 420 return REG_TEST; 421 } else if ((value == 0x0d) && !read) { 422 return REG_WPROTECT; 423 } else if ((value & 0x1c) == 0x08) { 424 /* RAM address 0x10 to 0x13 */ 425 return read | (REG_PRAM_ADDR + 0x10 + (value & 0x03)); 426 } else if ((value & 0x43) == 0x41) { 427 /* RAM address 0x00 to 0x0f */ 428 return read | (REG_PRAM_ADDR + (value & 0x0f)); 429 } 430 } 431 return REG_INVALID; 432 } 433 434 static void via1_rtc_update(MOS6522Q800VIA1State *v1s) 435 { 436 MOS6522State *s = MOS6522(v1s); 437 int cmd, sector, addr; 438 uint32_t time; 439 440 if (s->b & VIA1B_vRTCEnb) { 441 return; 442 } 443 444 if (s->dirb & VIA1B_vRTCData) { 445 /* send bits to the RTC */ 446 if (!(v1s->last_b & VIA1B_vRTCClk) && (s->b & VIA1B_vRTCClk)) { 447 v1s->data_out <<= 1; 448 v1s->data_out |= s->b & VIA1B_vRTCData; 449 v1s->data_out_cnt++; 450 } 451 trace_via1_rtc_update_data_out(v1s->data_out_cnt, v1s->data_out); 452 } else { 453 trace_via1_rtc_update_data_in(v1s->data_in_cnt, v1s->data_in); 454 /* receive bits from the RTC */ 455 if ((v1s->last_b & VIA1B_vRTCClk) && 456 !(s->b & VIA1B_vRTCClk) && 457 v1s->data_in_cnt) { 458 s->b = (s->b & ~VIA1B_vRTCData) | 459 ((v1s->data_in >> 7) & VIA1B_vRTCData); 460 v1s->data_in <<= 1; 461 v1s->data_in_cnt--; 462 } 463 return; 464 } 465 466 if (v1s->data_out_cnt != 8) { 467 return; 468 } 469 470 v1s->data_out_cnt = 0; 471 472 trace_via1_rtc_internal_status(v1s->cmd, v1s->alt, v1s->data_out); 473 /* first byte: it's a command */ 474 if (v1s->cmd == REG_EMPTY) { 475 476 cmd = via1_rtc_compact_cmd(v1s->data_out); 477 trace_via1_rtc_internal_cmd(cmd); 478 479 if (cmd == REG_INVALID) { 480 trace_via1_rtc_cmd_invalid(v1s->data_out); 481 return; 482 } 483 484 if (cmd & 0x80) { /* this is a read command */ 485 switch (cmd & 0x7f) { 486 case REG_0...REG_3: /* seconds registers */ 487 /* 488 * register 0 is lowest-order byte 489 * register 3 is highest-order byte 490 */ 491 492 time = v1s->tick_offset + (qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) 493 / NANOSECONDS_PER_SECOND); 494 trace_via1_rtc_internal_time(time); 495 v1s->data_in = (time >> ((cmd & 0x03) << 3)) & 0xff; 496 v1s->data_in_cnt = 8; 497 trace_via1_rtc_cmd_seconds_read((cmd & 0x7f) - REG_0, 498 v1s->data_in); 499 break; 500 case REG_PRAM_ADDR...REG_PRAM_ADDR_LAST: 501 /* PRAM address 0x00 -> 0x13 */ 502 v1s->data_in = v1s->PRAM[(cmd & 0x7f) - REG_PRAM_ADDR]; 503 v1s->data_in_cnt = 8; 504 trace_via1_rtc_cmd_pram_read((cmd & 0x7f) - REG_PRAM_ADDR, 505 v1s->data_in); 506 break; 507 case REG_PRAM_SECT...REG_PRAM_SECT_LAST: 508 /* 509 * extended memory designator and sector number 510 * the only two-byte read command 511 */ 512 trace_via1_rtc_internal_set_cmd(cmd); 513 v1s->cmd = cmd; 514 break; 515 default: 516 g_assert_not_reached(); 517 break; 518 } 519 return; 520 } 521 522 /* this is a write command, needs a parameter */ 523 if (cmd == REG_WPROTECT || !v1s->wprotect) { 524 trace_via1_rtc_internal_set_cmd(cmd); 525 v1s->cmd = cmd; 526 } else { 527 trace_via1_rtc_internal_ignore_cmd(cmd); 528 } 529 return; 530 } 531 532 /* second byte: it's a parameter */ 533 if (v1s->alt == REG_EMPTY) { 534 switch (v1s->cmd & 0x7f) { 535 case REG_0...REG_3: /* seconds register */ 536 /* FIXME */ 537 trace_via1_rtc_cmd_seconds_write(v1s->cmd - REG_0, v1s->data_out); 538 v1s->cmd = REG_EMPTY; 539 break; 540 case REG_TEST: 541 /* device control: nothing to do */ 542 trace_via1_rtc_cmd_test_write(v1s->data_out); 543 v1s->cmd = REG_EMPTY; 544 break; 545 case REG_WPROTECT: 546 /* Write Protect register */ 547 trace_via1_rtc_cmd_wprotect_write(v1s->data_out); 548 v1s->wprotect = !!(v1s->data_out & 0x80); 549 v1s->cmd = REG_EMPTY; 550 break; 551 case REG_PRAM_ADDR...REG_PRAM_ADDR_LAST: 552 /* PRAM address 0x00 -> 0x13 */ 553 trace_via1_rtc_cmd_pram_write(v1s->cmd - REG_PRAM_ADDR, 554 v1s->data_out); 555 v1s->PRAM[v1s->cmd - REG_PRAM_ADDR] = v1s->data_out; 556 pram_update(v1s); 557 v1s->cmd = REG_EMPTY; 558 break; 559 case REG_PRAM_SECT...REG_PRAM_SECT_LAST: 560 addr = (v1s->data_out >> 2) & 0x1f; 561 sector = (v1s->cmd & 0x7f) - REG_PRAM_SECT; 562 if (v1s->cmd & 0x80) { 563 /* it's a read */ 564 v1s->data_in = v1s->PRAM[sector * 32 + addr]; 565 v1s->data_in_cnt = 8; 566 trace_via1_rtc_cmd_pram_sect_read(sector, addr, 567 sector * 32 + addr, 568 v1s->data_in); 569 v1s->cmd = REG_EMPTY; 570 } else { 571 /* it's a write, we need one more parameter */ 572 trace_via1_rtc_internal_set_alt(addr, sector, addr); 573 v1s->alt = addr; 574 } 575 break; 576 default: 577 g_assert_not_reached(); 578 break; 579 } 580 return; 581 } 582 583 /* third byte: it's the data of a REG_PRAM_SECT write */ 584 g_assert(REG_PRAM_SECT <= v1s->cmd && v1s->cmd <= REG_PRAM_SECT_LAST); 585 sector = v1s->cmd - REG_PRAM_SECT; 586 v1s->PRAM[sector * 32 + v1s->alt] = v1s->data_out; 587 pram_update(v1s); 588 trace_via1_rtc_cmd_pram_sect_write(sector, v1s->alt, sector * 32 + v1s->alt, 589 v1s->data_out); 590 v1s->alt = REG_EMPTY; 591 v1s->cmd = REG_EMPTY; 592 } 593 594 static void adb_via_poll(void *opaque) 595 { 596 MOS6522Q800VIA1State *v1s = MOS6522_Q800_VIA1(opaque); 597 MOS6522State *s = MOS6522(v1s); 598 ADBBusState *adb_bus = &v1s->adb_bus; 599 uint8_t obuf[9]; 600 uint8_t *data = &s->sr; 601 int olen; 602 603 /* 604 * Setting vADBInt below indicates that an autopoll reply has been 605 * received, however we must block autopoll until the point where 606 * the entire reply has been read back to the host 607 */ 608 adb_autopoll_block(adb_bus); 609 610 if (v1s->adb_data_in_size > 0 && v1s->adb_data_in_index == 0) { 611 /* 612 * For older Linux kernels that switch to IDLE mode after sending the 613 * ADB command, detect if there is an existing response and return that 614 * as a a "fake" autopoll reply or bus timeout accordingly 615 */ 616 *data = v1s->adb_data_out[0]; 617 olen = v1s->adb_data_in_size; 618 619 s->b &= ~VIA1B_vADBInt; 620 qemu_irq_raise(v1s->adb_data_ready); 621 } else { 622 /* 623 * Otherwise poll as normal 624 */ 625 v1s->adb_data_in_index = 0; 626 v1s->adb_data_out_index = 0; 627 olen = adb_poll(adb_bus, obuf, adb_bus->autopoll_mask); 628 629 if (olen > 0) { 630 /* Autopoll response */ 631 *data = obuf[0]; 632 olen--; 633 memcpy(v1s->adb_data_in, &obuf[1], olen); 634 v1s->adb_data_in_size = olen; 635 636 s->b &= ~VIA1B_vADBInt; 637 qemu_irq_raise(v1s->adb_data_ready); 638 } else { 639 *data = v1s->adb_autopoll_cmd; 640 obuf[0] = 0xff; 641 obuf[1] = 0xff; 642 olen = 2; 643 644 memcpy(v1s->adb_data_in, obuf, olen); 645 v1s->adb_data_in_size = olen; 646 647 s->b &= ~VIA1B_vADBInt; 648 qemu_irq_raise(v1s->adb_data_ready); 649 } 650 } 651 652 trace_via1_adb_poll(*data, (s->b & VIA1B_vADBInt) ? "+" : "-", 653 adb_bus->status, v1s->adb_data_in_index, olen); 654 } 655 656 static int adb_via_send_len(uint8_t data) 657 { 658 /* Determine the send length from the given ADB command */ 659 uint8_t cmd = data & 0xc; 660 uint8_t reg = data & 0x3; 661 662 switch (cmd) { 663 case 0x8: 664 /* Listen command */ 665 switch (reg) { 666 case 2: 667 /* Register 2 is only used for the keyboard */ 668 return 3; 669 case 3: 670 /* 671 * Fortunately our devices only implement writes 672 * to register 3 which is fixed at 2 bytes 673 */ 674 return 3; 675 default: 676 qemu_log_mask(LOG_UNIMP, "ADB unknown length for register %d\n", 677 reg); 678 return 1; 679 } 680 default: 681 /* Talk, BusReset */ 682 return 1; 683 } 684 } 685 686 static void adb_via_send(MOS6522Q800VIA1State *v1s, int state, uint8_t data) 687 { 688 MOS6522State *ms = MOS6522(v1s); 689 ADBBusState *adb_bus = &v1s->adb_bus; 690 uint16_t autopoll_mask; 691 692 switch (state) { 693 case ADB_STATE_NEW: 694 /* 695 * Command byte: vADBInt tells host autopoll data already present 696 * in VIA shift register and ADB transceiver 697 */ 698 adb_autopoll_block(adb_bus); 699 700 if (adb_bus->status & ADB_STATUS_POLLREPLY) { 701 /* Tell the host the existing data is from autopoll */ 702 ms->b &= ~VIA1B_vADBInt; 703 } else { 704 ms->b |= VIA1B_vADBInt; 705 v1s->adb_data_out_index = 0; 706 v1s->adb_data_out[v1s->adb_data_out_index++] = data; 707 } 708 709 trace_via1_adb_send(" NEW", data, (ms->b & VIA1B_vADBInt) ? "+" : "-"); 710 qemu_irq_raise(v1s->adb_data_ready); 711 break; 712 713 case ADB_STATE_EVEN: 714 case ADB_STATE_ODD: 715 ms->b |= VIA1B_vADBInt; 716 v1s->adb_data_out[v1s->adb_data_out_index++] = data; 717 718 trace_via1_adb_send(state == ADB_STATE_EVEN ? "EVEN" : " ODD", 719 data, (ms->b & VIA1B_vADBInt) ? "+" : "-"); 720 qemu_irq_raise(v1s->adb_data_ready); 721 break; 722 723 case ADB_STATE_IDLE: 724 return; 725 } 726 727 /* If the command is complete, execute it */ 728 if (v1s->adb_data_out_index == adb_via_send_len(v1s->adb_data_out[0])) { 729 v1s->adb_data_in_size = adb_request(adb_bus, v1s->adb_data_in, 730 v1s->adb_data_out, 731 v1s->adb_data_out_index); 732 v1s->adb_data_in_index = 0; 733 734 if (adb_bus->status & ADB_STATUS_BUSTIMEOUT) { 735 /* 736 * Bus timeout (but allow first EVEN and ODD byte to indicate 737 * timeout via vADBInt and SRQ status) 738 */ 739 v1s->adb_data_in[0] = 0xff; 740 v1s->adb_data_in[1] = 0xff; 741 v1s->adb_data_in_size = 2; 742 } 743 744 /* 745 * If last command is TALK, store it for use by autopoll and adjust 746 * the autopoll mask accordingly 747 */ 748 if ((v1s->adb_data_out[0] & 0xc) == 0xc) { 749 v1s->adb_autopoll_cmd = v1s->adb_data_out[0]; 750 751 autopoll_mask = 1 << (v1s->adb_autopoll_cmd >> 4); 752 adb_set_autopoll_mask(adb_bus, autopoll_mask); 753 } 754 } 755 } 756 757 static void adb_via_receive(MOS6522Q800VIA1State *v1s, int state, uint8_t *data) 758 { 759 MOS6522State *ms = MOS6522(v1s); 760 ADBBusState *adb_bus = &v1s->adb_bus; 761 uint16_t pending; 762 763 switch (state) { 764 case ADB_STATE_NEW: 765 ms->b |= VIA1B_vADBInt; 766 return; 767 768 case ADB_STATE_IDLE: 769 ms->b |= VIA1B_vADBInt; 770 adb_autopoll_unblock(adb_bus); 771 772 trace_via1_adb_receive("IDLE", *data, 773 (ms->b & VIA1B_vADBInt) ? "+" : "-", adb_bus->status, 774 v1s->adb_data_in_index, v1s->adb_data_in_size); 775 776 break; 777 778 case ADB_STATE_EVEN: 779 case ADB_STATE_ODD: 780 switch (v1s->adb_data_in_index) { 781 case 0: 782 /* First EVEN byte: vADBInt indicates bus timeout */ 783 *data = v1s->adb_data_in[v1s->adb_data_in_index]; 784 if (adb_bus->status & ADB_STATUS_BUSTIMEOUT) { 785 ms->b &= ~VIA1B_vADBInt; 786 } else { 787 ms->b |= VIA1B_vADBInt; 788 } 789 790 trace_via1_adb_receive(state == ADB_STATE_EVEN ? "EVEN" : " ODD", 791 *data, (ms->b & VIA1B_vADBInt) ? "+" : "-", 792 adb_bus->status, v1s->adb_data_in_index, 793 v1s->adb_data_in_size); 794 795 v1s->adb_data_in_index++; 796 break; 797 798 case 1: 799 /* First ODD byte: vADBInt indicates SRQ */ 800 *data = v1s->adb_data_in[v1s->adb_data_in_index]; 801 pending = adb_bus->pending & ~(1 << (v1s->adb_autopoll_cmd >> 4)); 802 if (pending) { 803 ms->b &= ~VIA1B_vADBInt; 804 } else { 805 ms->b |= VIA1B_vADBInt; 806 } 807 808 trace_via1_adb_receive(state == ADB_STATE_EVEN ? "EVEN" : " ODD", 809 *data, (ms->b & VIA1B_vADBInt) ? "+" : "-", 810 adb_bus->status, v1s->adb_data_in_index, 811 v1s->adb_data_in_size); 812 813 v1s->adb_data_in_index++; 814 break; 815 816 default: 817 /* 818 * Otherwise vADBInt indicates end of data. Note that Linux 819 * specifically checks for the sequence 0x0 0xff to confirm the 820 * end of the poll reply, so provide these extra bytes below to 821 * keep it happy 822 */ 823 if (v1s->adb_data_in_index < v1s->adb_data_in_size) { 824 /* Next data byte */ 825 *data = v1s->adb_data_in[v1s->adb_data_in_index]; 826 ms->b |= VIA1B_vADBInt; 827 } else if (v1s->adb_data_in_index == v1s->adb_data_in_size) { 828 if (adb_bus->status & ADB_STATUS_BUSTIMEOUT) { 829 /* Bus timeout (no more data) */ 830 *data = 0xff; 831 } else { 832 /* Return 0x0 after reply */ 833 *data = 0; 834 } 835 ms->b &= ~VIA1B_vADBInt; 836 } else { 837 /* Bus timeout (no more data) */ 838 *data = 0xff; 839 ms->b &= ~VIA1B_vADBInt; 840 adb_bus->status = 0; 841 adb_autopoll_unblock(adb_bus); 842 } 843 844 trace_via1_adb_receive(state == ADB_STATE_EVEN ? "EVEN" : " ODD", 845 *data, (ms->b & VIA1B_vADBInt) ? "+" : "-", 846 adb_bus->status, v1s->adb_data_in_index, 847 v1s->adb_data_in_size); 848 849 if (v1s->adb_data_in_index <= v1s->adb_data_in_size) { 850 v1s->adb_data_in_index++; 851 } 852 break; 853 } 854 855 qemu_irq_raise(v1s->adb_data_ready); 856 break; 857 } 858 } 859 860 static void via1_adb_update(MOS6522Q800VIA1State *v1s) 861 { 862 MOS6522State *s = MOS6522(v1s); 863 int oldstate, state; 864 865 oldstate = (v1s->last_b & VIA1B_vADB_StateMask) >> VIA1B_vADB_StateShift; 866 state = (s->b & VIA1B_vADB_StateMask) >> VIA1B_vADB_StateShift; 867 868 if (state != oldstate) { 869 if (s->acr & VIA1ACR_vShiftOut) { 870 /* output mode */ 871 adb_via_send(v1s, state, s->sr); 872 } else { 873 /* input mode */ 874 adb_via_receive(v1s, state, &s->sr); 875 } 876 } 877 } 878 879 static uint64_t mos6522_q800_via1_read(void *opaque, hwaddr addr, unsigned size) 880 { 881 MOS6522Q800VIA1State *s = MOS6522_Q800_VIA1(opaque); 882 MOS6522State *ms = MOS6522(s); 883 884 addr = (addr >> 9) & 0xf; 885 return mos6522_read(ms, addr, size); 886 } 887 888 static void mos6522_q800_via1_write(void *opaque, hwaddr addr, uint64_t val, 889 unsigned size) 890 { 891 MOS6522Q800VIA1State *v1s = MOS6522_Q800_VIA1(opaque); 892 MOS6522State *ms = MOS6522(v1s); 893 894 addr = (addr >> 9) & 0xf; 895 mos6522_write(ms, addr, val, size); 896 897 switch (addr) { 898 case VIA_REG_B: 899 via1_rtc_update(v1s); 900 via1_adb_update(v1s); 901 902 v1s->last_b = ms->b; 903 break; 904 } 905 } 906 907 static const MemoryRegionOps mos6522_q800_via1_ops = { 908 .read = mos6522_q800_via1_read, 909 .write = mos6522_q800_via1_write, 910 .endianness = DEVICE_BIG_ENDIAN, 911 .valid = { 912 .min_access_size = 1, 913 .max_access_size = 4, 914 }, 915 }; 916 917 static uint64_t mos6522_q800_via2_read(void *opaque, hwaddr addr, unsigned size) 918 { 919 MOS6522Q800VIA2State *s = MOS6522_Q800_VIA2(opaque); 920 MOS6522State *ms = MOS6522(s); 921 922 addr = (addr >> 9) & 0xf; 923 return mos6522_read(ms, addr, size); 924 } 925 926 static void mos6522_q800_via2_write(void *opaque, hwaddr addr, uint64_t val, 927 unsigned size) 928 { 929 MOS6522Q800VIA2State *s = MOS6522_Q800_VIA2(opaque); 930 MOS6522State *ms = MOS6522(s); 931 932 addr = (addr >> 9) & 0xf; 933 mos6522_write(ms, addr, val, size); 934 } 935 936 static const MemoryRegionOps mos6522_q800_via2_ops = { 937 .read = mos6522_q800_via2_read, 938 .write = mos6522_q800_via2_write, 939 .endianness = DEVICE_BIG_ENDIAN, 940 .valid = { 941 .min_access_size = 1, 942 .max_access_size = 4, 943 }, 944 }; 945 946 static void via1_postload_update_cb(void *opaque, bool running, RunState state) 947 { 948 MOS6522Q800VIA1State *v1s = MOS6522_Q800_VIA1(opaque); 949 950 qemu_del_vm_change_state_handler(v1s->vmstate); 951 v1s->vmstate = NULL; 952 953 pram_update(v1s); 954 } 955 956 static int via1_post_load(void *opaque, int version_id) 957 { 958 MOS6522Q800VIA1State *v1s = MOS6522_Q800_VIA1(opaque); 959 960 if (v1s->blk) { 961 v1s->vmstate = qemu_add_vm_change_state_handler( 962 via1_postload_update_cb, v1s); 963 } 964 965 return 0; 966 } 967 968 /* VIA 1 */ 969 static void mos6522_q800_via1_reset(DeviceState *dev) 970 { 971 MOS6522Q800VIA1State *v1s = MOS6522_Q800_VIA1(dev); 972 MOS6522State *ms = MOS6522(v1s); 973 MOS6522DeviceClass *mdc = MOS6522_GET_CLASS(ms); 974 ADBBusState *adb_bus = &v1s->adb_bus; 975 976 mdc->parent_reset(dev); 977 978 ms->timers[0].frequency = VIA_TIMER_FREQ; 979 ms->timers[1].frequency = VIA_TIMER_FREQ; 980 981 ms->b = VIA1B_vADB_StateMask | VIA1B_vADBInt | VIA1B_vRTCEnb; 982 983 /* ADB/RTC */ 984 adb_set_autopoll_enabled(adb_bus, true); 985 v1s->cmd = REG_EMPTY; 986 v1s->alt = REG_EMPTY; 987 } 988 989 static void mos6522_q800_via1_realize(DeviceState *dev, Error **errp) 990 { 991 MOS6522Q800VIA1State *v1s = MOS6522_Q800_VIA1(dev); 992 ADBBusState *adb_bus = &v1s->adb_bus; 993 struct tm tm; 994 int ret; 995 996 v1s->one_second_timer = timer_new_ms(QEMU_CLOCK_VIRTUAL, via1_one_second, 997 v1s); 998 via1_one_second_update(v1s); 999 v1s->sixty_hz_timer = timer_new_ns(QEMU_CLOCK_VIRTUAL, via1_sixty_hz, 1000 v1s); 1001 via1_sixty_hz_update(v1s); 1002 1003 qemu_get_timedate(&tm, 0); 1004 v1s->tick_offset = (uint32_t)mktimegm(&tm) + RTC_OFFSET; 1005 1006 adb_register_autopoll_callback(adb_bus, adb_via_poll, v1s); 1007 v1s->adb_data_ready = qdev_get_gpio_in(dev, VIA1_IRQ_ADB_READY_BIT); 1008 1009 if (v1s->blk) { 1010 int64_t len = blk_getlength(v1s->blk); 1011 if (len < 0) { 1012 error_setg_errno(errp, -len, 1013 "could not get length of backing image"); 1014 return; 1015 } 1016 ret = blk_set_perm(v1s->blk, 1017 BLK_PERM_CONSISTENT_READ | BLK_PERM_WRITE, 1018 BLK_PERM_ALL, errp); 1019 if (ret < 0) { 1020 return; 1021 } 1022 1023 len = blk_pread(v1s->blk, 0, v1s->PRAM, sizeof(v1s->PRAM)); 1024 if (len != sizeof(v1s->PRAM)) { 1025 error_setg(errp, "can't read PRAM contents"); 1026 return; 1027 } 1028 } 1029 } 1030 1031 static void mos6522_q800_via1_init(Object *obj) 1032 { 1033 MOS6522Q800VIA1State *v1s = MOS6522_Q800_VIA1(obj); 1034 SysBusDevice *sbd = SYS_BUS_DEVICE(v1s); 1035 1036 memory_region_init_io(&v1s->via_mem, obj, &mos6522_q800_via1_ops, v1s, 1037 "via1", VIA_SIZE); 1038 sysbus_init_mmio(sbd, &v1s->via_mem); 1039 1040 /* ADB */ 1041 qbus_create_inplace((BusState *)&v1s->adb_bus, sizeof(v1s->adb_bus), 1042 TYPE_ADB_BUS, DEVICE(v1s), "adb.0"); 1043 1044 qdev_init_gpio_in(DEVICE(obj), via1_irq_request, VIA1_IRQ_NB); 1045 } 1046 1047 static const VMStateDescription vmstate_q800_via1 = { 1048 .name = "q800-via1", 1049 .version_id = 0, 1050 .minimum_version_id = 0, 1051 .post_load = via1_post_load, 1052 .fields = (VMStateField[]) { 1053 VMSTATE_STRUCT(parent_obj, MOS6522Q800VIA1State, 0, vmstate_mos6522, 1054 MOS6522State), 1055 VMSTATE_UINT8(last_b, MOS6522Q800VIA1State), 1056 /* RTC */ 1057 VMSTATE_BUFFER(PRAM, MOS6522Q800VIA1State), 1058 VMSTATE_UINT32(tick_offset, MOS6522Q800VIA1State), 1059 VMSTATE_UINT8(data_out, MOS6522Q800VIA1State), 1060 VMSTATE_INT32(data_out_cnt, MOS6522Q800VIA1State), 1061 VMSTATE_UINT8(data_in, MOS6522Q800VIA1State), 1062 VMSTATE_UINT8(data_in_cnt, MOS6522Q800VIA1State), 1063 VMSTATE_UINT8(cmd, MOS6522Q800VIA1State), 1064 VMSTATE_INT32(wprotect, MOS6522Q800VIA1State), 1065 VMSTATE_INT32(alt, MOS6522Q800VIA1State), 1066 /* ADB */ 1067 VMSTATE_INT32(adb_data_in_size, MOS6522Q800VIA1State), 1068 VMSTATE_INT32(adb_data_in_index, MOS6522Q800VIA1State), 1069 VMSTATE_INT32(adb_data_out_index, MOS6522Q800VIA1State), 1070 VMSTATE_BUFFER(adb_data_in, MOS6522Q800VIA1State), 1071 VMSTATE_BUFFER(adb_data_out, MOS6522Q800VIA1State), 1072 VMSTATE_UINT8(adb_autopoll_cmd, MOS6522Q800VIA1State), 1073 /* Timers */ 1074 VMSTATE_TIMER_PTR(one_second_timer, MOS6522Q800VIA1State), 1075 VMSTATE_INT64(next_second, MOS6522Q800VIA1State), 1076 VMSTATE_TIMER_PTR(sixty_hz_timer, MOS6522Q800VIA1State), 1077 VMSTATE_INT64(next_sixty_hz, MOS6522Q800VIA1State), 1078 VMSTATE_END_OF_LIST() 1079 } 1080 }; 1081 1082 static Property mos6522_q800_via1_properties[] = { 1083 DEFINE_PROP_DRIVE("drive", MOS6522Q800VIA1State, blk), 1084 DEFINE_PROP_END_OF_LIST(), 1085 }; 1086 1087 static void mos6522_q800_via1_class_init(ObjectClass *oc, void *data) 1088 { 1089 DeviceClass *dc = DEVICE_CLASS(oc); 1090 1091 dc->realize = mos6522_q800_via1_realize; 1092 dc->reset = mos6522_q800_via1_reset; 1093 dc->vmsd = &vmstate_q800_via1; 1094 device_class_set_props(dc, mos6522_q800_via1_properties); 1095 } 1096 1097 static const TypeInfo mos6522_q800_via1_type_info = { 1098 .name = TYPE_MOS6522_Q800_VIA1, 1099 .parent = TYPE_MOS6522, 1100 .instance_size = sizeof(MOS6522Q800VIA1State), 1101 .instance_init = mos6522_q800_via1_init, 1102 .class_init = mos6522_q800_via1_class_init, 1103 }; 1104 1105 /* VIA 2 */ 1106 static void mos6522_q800_via2_portB_write(MOS6522State *s) 1107 { 1108 if (s->dirb & VIA2B_vPower && (s->b & VIA2B_vPower) == 0) { 1109 /* shutdown */ 1110 qemu_system_shutdown_request(SHUTDOWN_CAUSE_GUEST_SHUTDOWN); 1111 } 1112 } 1113 1114 static void mos6522_q800_via2_reset(DeviceState *dev) 1115 { 1116 MOS6522State *ms = MOS6522(dev); 1117 MOS6522DeviceClass *mdc = MOS6522_GET_CLASS(ms); 1118 1119 mdc->parent_reset(dev); 1120 1121 ms->timers[0].frequency = VIA_TIMER_FREQ; 1122 ms->timers[1].frequency = VIA_TIMER_FREQ; 1123 1124 ms->dirb = 0; 1125 ms->b = 0; 1126 ms->dira = 0; 1127 ms->a = 0x7f; 1128 } 1129 1130 static void via2_nubus_irq_request(void *opaque, int irq, int level) 1131 { 1132 MOS6522Q800VIA2State *v2s = opaque; 1133 MOS6522State *s = MOS6522(v2s); 1134 MOS6522DeviceClass *mdc = MOS6522_GET_CLASS(s); 1135 1136 if (level) { 1137 /* Port A nubus IRQ inputs are active LOW */ 1138 s->a &= ~(1 << irq); 1139 s->ifr |= 1 << VIA2_IRQ_NUBUS_BIT; 1140 } else { 1141 s->a |= (1 << irq); 1142 s->ifr &= ~(1 << VIA2_IRQ_NUBUS_BIT); 1143 } 1144 1145 mdc->update_irq(s); 1146 } 1147 1148 static void mos6522_q800_via2_init(Object *obj) 1149 { 1150 MOS6522Q800VIA2State *v2s = MOS6522_Q800_VIA2(obj); 1151 SysBusDevice *sbd = SYS_BUS_DEVICE(v2s); 1152 1153 memory_region_init_io(&v2s->via_mem, obj, &mos6522_q800_via2_ops, v2s, 1154 "via2", VIA_SIZE); 1155 sysbus_init_mmio(sbd, &v2s->via_mem); 1156 1157 qdev_init_gpio_in(DEVICE(obj), via2_irq_request, VIA2_IRQ_NB); 1158 1159 qdev_init_gpio_in_named(DEVICE(obj), via2_nubus_irq_request, "nubus-irq", 1160 VIA2_NUBUS_IRQ_NB); 1161 } 1162 1163 static const VMStateDescription vmstate_q800_via2 = { 1164 .name = "q800-via2", 1165 .version_id = 0, 1166 .minimum_version_id = 0, 1167 .fields = (VMStateField[]) { 1168 VMSTATE_STRUCT(parent_obj, MOS6522Q800VIA2State, 0, vmstate_mos6522, 1169 MOS6522State), 1170 VMSTATE_END_OF_LIST() 1171 } 1172 }; 1173 1174 static void mos6522_q800_via2_class_init(ObjectClass *oc, void *data) 1175 { 1176 DeviceClass *dc = DEVICE_CLASS(oc); 1177 MOS6522DeviceClass *mdc = MOS6522_CLASS(oc); 1178 1179 dc->reset = mos6522_q800_via2_reset; 1180 dc->vmsd = &vmstate_q800_via2; 1181 mdc->portB_write = mos6522_q800_via2_portB_write; 1182 } 1183 1184 static const TypeInfo mos6522_q800_via2_type_info = { 1185 .name = TYPE_MOS6522_Q800_VIA2, 1186 .parent = TYPE_MOS6522, 1187 .instance_size = sizeof(MOS6522Q800VIA2State), 1188 .instance_init = mos6522_q800_via2_init, 1189 .class_init = mos6522_q800_via2_class_init, 1190 }; 1191 1192 static void mac_via_register_types(void) 1193 { 1194 type_register_static(&mos6522_q800_via1_type_info); 1195 type_register_static(&mos6522_q800_via2_type_info); 1196 } 1197 1198 type_init(mac_via_register_types); 1199