1 /* 2 * QEMU m68k Macintosh VIA device support 3 * 4 * Copyright (c) 2011-2018 Laurent Vivier 5 * Copyright (c) 2018 Mark Cave-Ayland 6 * 7 * Some parts from hw/misc/macio/cuda.c 8 * 9 * Copyright (c) 2004-2007 Fabrice Bellard 10 * Copyright (c) 2007 Jocelyn Mayer 11 * 12 * some parts from linux-2.6.29, arch/m68k/include/asm/mac_via.h 13 * 14 * This work is licensed under the terms of the GNU GPL, version 2 or later. 15 * See the COPYING file in the top-level directory. 16 */ 17 18 #include "qemu/osdep.h" 19 #include "qemu-common.h" 20 #include "migration/vmstate.h" 21 #include "hw/sysbus.h" 22 #include "hw/irq.h" 23 #include "qemu/timer.h" 24 #include "hw/misc/mac_via.h" 25 #include "hw/misc/mos6522.h" 26 #include "hw/input/adb.h" 27 #include "sysemu/runstate.h" 28 #include "qapi/error.h" 29 #include "qemu/cutils.h" 30 #include "hw/qdev-properties.h" 31 #include "sysemu/block-backend.h" 32 #include "trace.h" 33 #include "qemu/log.h" 34 35 /* 36 * VIAs: There are two in every machine, 37 */ 38 39 #define VIA_SIZE (0x2000) 40 41 /* 42 * Not all of these are true post MacII I think. 43 * CSA: probably the ones CHRP marks as 'unused' change purposes 44 * when the IWM becomes the SWIM. 45 * http://www.rs6000.ibm.com/resource/technology/chrpio/via5.mak.html 46 * ftp://ftp.austin.ibm.com/pub/technology/spec/chrp/inwork/CHRP_IORef_1.0.pdf 47 * 48 * also, http://developer.apple.com/technotes/hw/hw_09.html claims the 49 * following changes for IIfx: 50 * VIA1A_vSccWrReq not available and that VIA1A_vSync has moved to an IOP. 51 * Also, "All of the functionality of VIA2 has been moved to other chips". 52 */ 53 54 #define VIA1A_vSccWrReq 0x80 /* 55 * SCC write. (input) 56 * [CHRP] SCC WREQ: Reflects the state of the 57 * Wait/Request pins from the SCC. 58 * [Macintosh Family Hardware] 59 * as CHRP on SE/30,II,IIx,IIcx,IIci. 60 * on IIfx, "0 means an active request" 61 */ 62 #define VIA1A_vRev8 0x40 /* 63 * Revision 8 board ??? 64 * [CHRP] En WaitReqB: Lets the WaitReq_L 65 * signal from port B of the SCC appear on 66 * the PA7 input pin. Output. 67 * [Macintosh Family] On the SE/30, this 68 * is the bit to flip screen buffers. 69 * 0=alternate, 1=main. 70 * on II,IIx,IIcx,IIci,IIfx this is a bit 71 * for Rev ID. 0=II,IIx, 1=IIcx,IIci,IIfx 72 */ 73 #define VIA1A_vHeadSel 0x20 /* 74 * Head select for IWM. 75 * [CHRP] unused. 76 * [Macintosh Family] "Floppy disk 77 * state-control line SEL" on all but IIfx 78 */ 79 #define VIA1A_vOverlay 0x10 /* 80 * [Macintosh Family] On SE/30,II,IIx,IIcx 81 * this bit enables the "Overlay" address 82 * map in the address decoders as it is on 83 * reset for mapping the ROM over the reset 84 * vector. 1=use overlay map. 85 * On the IIci,IIfx it is another bit of the 86 * CPU ID: 0=normal IIci, 1=IIci with parity 87 * feature or IIfx. 88 * [CHRP] En WaitReqA: Lets the WaitReq_L 89 * signal from port A of the SCC appear 90 * on the PA7 input pin (CHRP). Output. 91 * [MkLinux] "Drive Select" 92 * (with 0x20 being 'disk head select') 93 */ 94 #define VIA1A_vSync 0x08 /* 95 * [CHRP] Sync Modem: modem clock select: 96 * 1: select the external serial clock to 97 * drive the SCC's /RTxCA pin. 98 * 0: Select the 3.6864MHz clock to drive 99 * the SCC cell. 100 * [Macintosh Family] Correct on all but IIfx 101 */ 102 103 /* 104 * Macintosh Family Hardware sez: bits 0-2 of VIA1A are volume control 105 * on Macs which had the PWM sound hardware. Reserved on newer models. 106 * On IIci,IIfx, bits 1-2 are the rest of the CPU ID: 107 * bit 2: 1=IIci, 0=IIfx 108 * bit 1: 1 on both IIci and IIfx. 109 * MkLinux sez bit 0 is 'burnin flag' in this case. 110 * CHRP sez: VIA1A bits 0-2 and 5 are 'unused': if programmed as 111 * inputs, these bits will read 0. 112 */ 113 #define VIA1A_vVolume 0x07 /* Audio volume mask for PWM */ 114 #define VIA1A_CPUID0 0x02 /* CPU id bit 0 on RBV, others */ 115 #define VIA1A_CPUID1 0x04 /* CPU id bit 0 on RBV, others */ 116 #define VIA1A_CPUID2 0x10 /* CPU id bit 0 on RBV, others */ 117 #define VIA1A_CPUID3 0x40 /* CPU id bit 0 on RBV, others */ 118 119 /* 120 * Info on VIA1B is from Macintosh Family Hardware & MkLinux. 121 * CHRP offers no info. 122 */ 123 #define VIA1B_vSound 0x80 /* 124 * Sound enable (for compatibility with 125 * PWM hardware) 0=enabled. 126 * Also, on IIci w/parity, shows parity error 127 * 0=error, 1=OK. 128 */ 129 #define VIA1B_vMystery 0x40 /* 130 * On IIci, parity enable. 0=enabled,1=disabled 131 * On SE/30, vertical sync interrupt enable. 132 * 0=enabled. This vSync interrupt shows up 133 * as a slot $E interrupt. 134 */ 135 #define VIA1B_vADBS2 0x20 /* ADB state input bit 1 (unused on IIfx) */ 136 #define VIA1B_vADBS1 0x10 /* ADB state input bit 0 (unused on IIfx) */ 137 #define VIA1B_vADBInt 0x08 /* ADB interrupt 0=interrupt (unused on IIfx)*/ 138 #define VIA1B_vRTCEnb 0x04 /* Enable Real time clock. 0=enabled. */ 139 #define VIA1B_vRTCClk 0x02 /* Real time clock serial-clock line. */ 140 #define VIA1B_vRTCData 0x01 /* Real time clock serial-data line. */ 141 142 /* 143 * VIA2 A register is the interrupt lines raised off the nubus 144 * slots. 145 * The below info is from 'Macintosh Family Hardware.' 146 * MkLinux calls the 'IIci internal video IRQ' below the 'RBV slot 0 irq.' 147 * It also notes that the slot $9 IRQ is the 'Ethernet IRQ' and 148 * defines the 'Video IRQ' as 0x40 for the 'EVR' VIA work-alike. 149 * Perhaps OSS uses vRAM1 and vRAM2 for ADB. 150 */ 151 152 #define VIA2A_vRAM1 0x80 /* RAM size bit 1 (IIci: reserved) */ 153 #define VIA2A_vRAM0 0x40 /* RAM size bit 0 (IIci: internal video IRQ) */ 154 #define VIA2A_vIRQE 0x20 /* IRQ from slot $E */ 155 #define VIA2A_vIRQD 0x10 /* IRQ from slot $D */ 156 #define VIA2A_vIRQC 0x08 /* IRQ from slot $C */ 157 #define VIA2A_vIRQB 0x04 /* IRQ from slot $B */ 158 #define VIA2A_vIRQA 0x02 /* IRQ from slot $A */ 159 #define VIA2A_vIRQ9 0x01 /* IRQ from slot $9 */ 160 161 /* 162 * RAM size bits decoded as follows: 163 * bit1 bit0 size of ICs in bank A 164 * 0 0 256 kbit 165 * 0 1 1 Mbit 166 * 1 0 4 Mbit 167 * 1 1 16 Mbit 168 */ 169 170 /* 171 * Register B has the fun stuff in it 172 */ 173 174 #define VIA2B_vVBL 0x80 /* 175 * VBL output to VIA1 (60.15Hz) driven by 176 * timer T1. 177 * on IIci, parity test: 0=test mode. 178 * [MkLinux] RBV_PARODD: 1=odd,0=even. 179 */ 180 #define VIA2B_vSndJck 0x40 /* 181 * External sound jack status. 182 * 0=plug is inserted. On SE/30, always 0 183 */ 184 #define VIA2B_vTfr0 0x20 /* Transfer mode bit 0 ack from NuBus */ 185 #define VIA2B_vTfr1 0x10 /* Transfer mode bit 1 ack from NuBus */ 186 #define VIA2B_vMode32 0x08 /* 187 * 24/32bit switch - doubles as cache flush 188 * on II, AMU/PMMU control. 189 * if AMU, 0=24bit to 32bit translation 190 * if PMMU, 1=PMMU is accessing page table. 191 * on SE/30 tied low. 192 * on IIx,IIcx,IIfx, unused. 193 * on IIci/RBV, cache control. 0=flush cache. 194 */ 195 #define VIA2B_vPower 0x04 /* 196 * Power off, 0=shut off power. 197 * on SE/30 this signal sent to PDS card. 198 */ 199 #define VIA2B_vBusLk 0x02 /* 200 * Lock NuBus transactions, 0=locked. 201 * on SE/30 sent to PDS card. 202 */ 203 #define VIA2B_vCDis 0x01 /* 204 * Cache control. On IIci, 1=disable cache card 205 * on others, 0=disable processor's instruction 206 * and data caches. 207 */ 208 209 /* interrupt flags */ 210 211 #define IRQ_SET 0x80 212 213 /* common */ 214 215 #define VIA_IRQ_TIMER1 0x40 216 #define VIA_IRQ_TIMER2 0x20 217 218 /* 219 * Apple sez: http://developer.apple.com/technotes/ov/ov_04.html 220 * Another example of a valid function that has no ROM support is the use 221 * of the alternate video page for page-flipping animation. Since there 222 * is no ROM call to flip pages, it is necessary to go play with the 223 * right bit in the VIA chip (6522 Versatile Interface Adapter). 224 * [CSA: don't know which one this is, but it's one of 'em!] 225 */ 226 227 /* 228 * 6522 registers - see databook. 229 * CSA: Assignments for VIA1 confirmed from CHRP spec. 230 */ 231 232 /* partial address decode. 0xYYXX : XX part for RBV, YY part for VIA */ 233 /* Note: 15 VIA regs, 8 RBV regs */ 234 235 #define vBufB 0x0000 /* [VIA/RBV] Register B */ 236 #define vBufAH 0x0200 /* [VIA only] Buffer A, with handshake. DON'T USE! */ 237 #define vDirB 0x0400 /* [VIA only] Data Direction Register B. */ 238 #define vDirA 0x0600 /* [VIA only] Data Direction Register A. */ 239 #define vT1CL 0x0800 /* [VIA only] Timer one counter low. */ 240 #define vT1CH 0x0a00 /* [VIA only] Timer one counter high. */ 241 #define vT1LL 0x0c00 /* [VIA only] Timer one latches low. */ 242 #define vT1LH 0x0e00 /* [VIA only] Timer one latches high. */ 243 #define vT2CL 0x1000 /* [VIA only] Timer two counter low. */ 244 #define vT2CH 0x1200 /* [VIA only] Timer two counter high. */ 245 #define vSR 0x1400 /* [VIA only] Shift register. */ 246 #define vACR 0x1600 /* [VIA only] Auxilary control register. */ 247 #define vPCR 0x1800 /* [VIA only] Peripheral control register. */ 248 /* 249 * CHRP sez never ever to *write* this. 250 * Mac family says never to *change* this. 251 * In fact we need to initialize it once at start. 252 */ 253 #define vIFR 0x1a00 /* [VIA/RBV] Interrupt flag register. */ 254 #define vIER 0x1c00 /* [VIA/RBV] Interrupt enable register. */ 255 #define vBufA 0x1e00 /* [VIA/RBV] register A (no handshake) */ 256 257 /* from linux 2.6 drivers/macintosh/via-macii.c */ 258 259 /* Bits in ACR */ 260 261 #define VIA1ACR_vShiftCtrl 0x1c /* Shift register control bits */ 262 #define VIA1ACR_vShiftExtClk 0x0c /* Shift on external clock */ 263 #define VIA1ACR_vShiftOut 0x10 /* Shift out if 1 */ 264 265 /* 266 * Apple Macintosh Family Hardware Refenece 267 * Table 19-10 ADB transaction states 268 */ 269 270 #define ADB_STATE_NEW 0 271 #define ADB_STATE_EVEN 1 272 #define ADB_STATE_ODD 2 273 #define ADB_STATE_IDLE 3 274 275 #define VIA1B_vADB_StateMask (VIA1B_vADBS1 | VIA1B_vADBS2) 276 #define VIA1B_vADB_StateShift 4 277 278 #define VIA_TIMER_FREQ (783360) 279 #define VIA_ADB_POLL_FREQ 50 /* XXX: not real */ 280 281 /* VIA returns time offset from Jan 1, 1904, not 1970 */ 282 #define RTC_OFFSET 2082844800 283 284 enum { 285 REG_0, 286 REG_1, 287 REG_2, 288 REG_3, 289 REG_TEST, 290 REG_WPROTECT, 291 REG_PRAM_ADDR, 292 REG_PRAM_ADDR_LAST = REG_PRAM_ADDR + 19, 293 REG_PRAM_SECT, 294 REG_PRAM_SECT_LAST = REG_PRAM_SECT + 7, 295 REG_INVALID, 296 REG_EMPTY = 0xff, 297 }; 298 299 static void via1_VBL_update(MOS6522Q800VIA1State *v1s) 300 { 301 MOS6522State *s = MOS6522(v1s); 302 303 /* 60 Hz irq */ 304 v1s->next_VBL = (qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + 16630) / 305 16630 * 16630; 306 307 if (s->ier & VIA1_IRQ_VBLANK) { 308 timer_mod(v1s->VBL_timer, v1s->next_VBL); 309 } else { 310 timer_del(v1s->VBL_timer); 311 } 312 } 313 314 static void via1_one_second_update(MOS6522Q800VIA1State *v1s) 315 { 316 MOS6522State *s = MOS6522(v1s); 317 318 v1s->next_second = (qemu_clock_get_ms(QEMU_CLOCK_VIRTUAL) + 1000) / 319 1000 * 1000; 320 if (s->ier & VIA1_IRQ_ONE_SECOND) { 321 timer_mod(v1s->one_second_timer, v1s->next_second); 322 } else { 323 timer_del(v1s->one_second_timer); 324 } 325 } 326 327 static void via1_VBL(void *opaque) 328 { 329 MOS6522Q800VIA1State *v1s = opaque; 330 MOS6522State *s = MOS6522(v1s); 331 MOS6522DeviceClass *mdc = MOS6522_DEVICE_GET_CLASS(s); 332 333 s->ifr |= VIA1_IRQ_VBLANK; 334 mdc->update_irq(s); 335 336 via1_VBL_update(v1s); 337 } 338 339 static void via1_one_second(void *opaque) 340 { 341 MOS6522Q800VIA1State *v1s = opaque; 342 MOS6522State *s = MOS6522(v1s); 343 MOS6522DeviceClass *mdc = MOS6522_DEVICE_GET_CLASS(s); 344 345 s->ifr |= VIA1_IRQ_ONE_SECOND; 346 mdc->update_irq(s); 347 348 via1_one_second_update(v1s); 349 } 350 351 static void via1_irq_request(void *opaque, int irq, int level) 352 { 353 MOS6522Q800VIA1State *v1s = opaque; 354 MOS6522State *s = MOS6522(v1s); 355 MOS6522DeviceClass *mdc = MOS6522_DEVICE_GET_CLASS(s); 356 357 if (level) { 358 s->ifr |= 1 << irq; 359 } else { 360 s->ifr &= ~(1 << irq); 361 } 362 363 mdc->update_irq(s); 364 } 365 366 static void via2_irq_request(void *opaque, int irq, int level) 367 { 368 MOS6522Q800VIA2State *v2s = opaque; 369 MOS6522State *s = MOS6522(v2s); 370 MOS6522DeviceClass *mdc = MOS6522_DEVICE_GET_CLASS(s); 371 372 if (level) { 373 s->ifr |= 1 << irq; 374 } else { 375 s->ifr &= ~(1 << irq); 376 } 377 378 mdc->update_irq(s); 379 } 380 381 382 static void pram_update(MacVIAState *m) 383 { 384 if (m->blk) { 385 if (blk_pwrite(m->blk, 0, m->mos6522_via1.PRAM, 386 sizeof(m->mos6522_via1.PRAM), 0) < 0) { 387 qemu_log("pram_update: cannot write to file\n"); 388 } 389 } 390 } 391 392 /* 393 * RTC Commands 394 * 395 * Command byte Register addressed by the command 396 * 397 * z0000001 Seconds register 0 (lowest-order byte) 398 * z0000101 Seconds register 1 399 * z0001001 Seconds register 2 400 * z0001101 Seconds register 3 (highest-order byte) 401 * 00110001 Test register (write-only) 402 * 00110101 Write-Protect Register (write-only) 403 * z010aa01 RAM address 100aa ($10-$13) (first 20 bytes only) 404 * z1aaaa01 RAM address 0aaaa ($00-$0F) (first 20 bytes only) 405 * z0111aaa Extended memory designator and sector number 406 * 407 * For a read request, z=1, for a write z=0 408 * The letter a indicates bits whose value depend on what parameter 409 * RAM byte you want to address 410 */ 411 static int via1_rtc_compact_cmd(uint8_t value) 412 { 413 uint8_t read = value & 0x80; 414 415 value &= 0x7f; 416 417 /* the last 2 bits of a command byte must always be 0b01 ... */ 418 if ((value & 0x78) == 0x38) { 419 /* except for the extended memory designator */ 420 return read | (REG_PRAM_SECT + (value & 0x07)); 421 } 422 if ((value & 0x03) == 0x01) { 423 value >>= 2; 424 if ((value & 0x1c) == 0) { 425 /* seconds registers */ 426 return read | (REG_0 + (value & 0x03)); 427 } else if ((value == 0x0c) && !read) { 428 return REG_TEST; 429 } else if ((value == 0x0d) && !read) { 430 return REG_WPROTECT; 431 } else if ((value & 0x1c) == 0x08) { 432 /* RAM address 0x10 to 0x13 */ 433 return read | (REG_PRAM_ADDR + 0x10 + (value & 0x03)); 434 } else if ((value & 0x43) == 0x41) { 435 /* RAM address 0x00 to 0x0f */ 436 return read | (REG_PRAM_ADDR + (value & 0x0f)); 437 } 438 } 439 return REG_INVALID; 440 } 441 442 static void via1_rtc_update(MacVIAState *m) 443 { 444 MOS6522Q800VIA1State *v1s = &m->mos6522_via1; 445 MOS6522State *s = MOS6522(v1s); 446 int cmd, sector, addr; 447 uint32_t time; 448 449 if (s->b & VIA1B_vRTCEnb) { 450 return; 451 } 452 453 if (s->dirb & VIA1B_vRTCData) { 454 /* send bits to the RTC */ 455 if (!(v1s->last_b & VIA1B_vRTCClk) && (s->b & VIA1B_vRTCClk)) { 456 m->data_out <<= 1; 457 m->data_out |= s->b & VIA1B_vRTCData; 458 m->data_out_cnt++; 459 } 460 trace_via1_rtc_update_data_out(m->data_out_cnt, m->data_out); 461 } else { 462 trace_via1_rtc_update_data_in(m->data_in_cnt, m->data_in); 463 /* receive bits from the RTC */ 464 if ((v1s->last_b & VIA1B_vRTCClk) && 465 !(s->b & VIA1B_vRTCClk) && 466 m->data_in_cnt) { 467 s->b = (s->b & ~VIA1B_vRTCData) | 468 ((m->data_in >> 7) & VIA1B_vRTCData); 469 m->data_in <<= 1; 470 m->data_in_cnt--; 471 } 472 return; 473 } 474 475 if (m->data_out_cnt != 8) { 476 return; 477 } 478 479 m->data_out_cnt = 0; 480 481 trace_via1_rtc_internal_status(m->cmd, m->alt, m->data_out); 482 /* first byte: it's a command */ 483 if (m->cmd == REG_EMPTY) { 484 485 cmd = via1_rtc_compact_cmd(m->data_out); 486 trace_via1_rtc_internal_cmd(cmd); 487 488 if (cmd == REG_INVALID) { 489 trace_via1_rtc_cmd_invalid(m->data_out); 490 return; 491 } 492 493 if (cmd & 0x80) { /* this is a read command */ 494 switch (cmd & 0x7f) { 495 case REG_0...REG_3: /* seconds registers */ 496 /* 497 * register 0 is lowest-order byte 498 * register 3 is highest-order byte 499 */ 500 501 time = m->tick_offset + (qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) 502 / NANOSECONDS_PER_SECOND); 503 trace_via1_rtc_internal_time(time); 504 m->data_in = (time >> ((cmd & 0x03) << 3)) & 0xff; 505 m->data_in_cnt = 8; 506 trace_via1_rtc_cmd_seconds_read((cmd & 0x7f) - REG_0, 507 m->data_in); 508 break; 509 case REG_PRAM_ADDR...REG_PRAM_ADDR_LAST: 510 /* PRAM address 0x00 -> 0x13 */ 511 m->data_in = v1s->PRAM[(cmd & 0x7f) - REG_PRAM_ADDR]; 512 m->data_in_cnt = 8; 513 trace_via1_rtc_cmd_pram_read((cmd & 0x7f) - REG_PRAM_ADDR, 514 m->data_in); 515 break; 516 case REG_PRAM_SECT...REG_PRAM_SECT_LAST: 517 /* 518 * extended memory designator and sector number 519 * the only two-byte read command 520 */ 521 trace_via1_rtc_internal_set_cmd(cmd); 522 m->cmd = cmd; 523 break; 524 default: 525 g_assert_not_reached(); 526 break; 527 } 528 return; 529 } 530 531 /* this is a write command, needs a parameter */ 532 if (cmd == REG_WPROTECT || !m->wprotect) { 533 trace_via1_rtc_internal_set_cmd(cmd); 534 m->cmd = cmd; 535 } else { 536 trace_via1_rtc_internal_ignore_cmd(cmd); 537 } 538 return; 539 } 540 541 /* second byte: it's a parameter */ 542 if (m->alt == REG_EMPTY) { 543 switch (m->cmd & 0x7f) { 544 case REG_0...REG_3: /* seconds register */ 545 /* FIXME */ 546 trace_via1_rtc_cmd_seconds_write(m->cmd - REG_0, m->data_out); 547 m->cmd = REG_EMPTY; 548 break; 549 case REG_TEST: 550 /* device control: nothing to do */ 551 trace_via1_rtc_cmd_test_write(m->data_out); 552 m->cmd = REG_EMPTY; 553 break; 554 case REG_WPROTECT: 555 /* Write Protect register */ 556 trace_via1_rtc_cmd_wprotect_write(m->data_out); 557 m->wprotect = !!(m->data_out & 0x80); 558 m->cmd = REG_EMPTY; 559 break; 560 case REG_PRAM_ADDR...REG_PRAM_ADDR_LAST: 561 /* PRAM address 0x00 -> 0x13 */ 562 trace_via1_rtc_cmd_pram_write(m->cmd - REG_PRAM_ADDR, m->data_out); 563 v1s->PRAM[m->cmd - REG_PRAM_ADDR] = m->data_out; 564 pram_update(m); 565 m->cmd = REG_EMPTY; 566 break; 567 case REG_PRAM_SECT...REG_PRAM_SECT_LAST: 568 addr = (m->data_out >> 2) & 0x1f; 569 sector = (m->cmd & 0x7f) - REG_PRAM_SECT; 570 if (m->cmd & 0x80) { 571 /* it's a read */ 572 m->data_in = v1s->PRAM[sector * 32 + addr]; 573 m->data_in_cnt = 8; 574 trace_via1_rtc_cmd_pram_sect_read(sector, addr, 575 sector * 32 + addr, 576 m->data_in); 577 m->cmd = REG_EMPTY; 578 } else { 579 /* it's a write, we need one more parameter */ 580 trace_via1_rtc_internal_set_alt(addr, sector, addr); 581 m->alt = addr; 582 } 583 break; 584 default: 585 g_assert_not_reached(); 586 break; 587 } 588 return; 589 } 590 591 /* third byte: it's the data of a REG_PRAM_SECT write */ 592 g_assert(REG_PRAM_SECT <= m->cmd && m->cmd <= REG_PRAM_SECT_LAST); 593 sector = m->cmd - REG_PRAM_SECT; 594 v1s->PRAM[sector * 32 + m->alt] = m->data_out; 595 pram_update(m); 596 trace_via1_rtc_cmd_pram_sect_write(sector, m->alt, sector * 32 + m->alt, 597 m->data_out); 598 m->alt = REG_EMPTY; 599 m->cmd = REG_EMPTY; 600 } 601 602 static void adb_via_poll(void *opaque) 603 { 604 MacVIAState *m = opaque; 605 MOS6522Q800VIA1State *v1s = MOS6522_Q800_VIA1(&m->mos6522_via1); 606 MOS6522State *s = MOS6522(v1s); 607 ADBBusState *adb_bus = &m->adb_bus; 608 uint8_t obuf[9]; 609 uint8_t *data = &s->sr; 610 int olen; 611 uint16_t pending; 612 613 /* 614 * Setting vADBInt below indicates that an autopoll reply has been 615 * received, however we must block autopoll until the point where 616 * the entire reply has been read back to the host 617 */ 618 adb_autopoll_block(adb_bus); 619 620 m->adb_data_in_index = 0; 621 m->adb_data_out_index = 0; 622 olen = adb_poll(adb_bus, obuf, adb_bus->autopoll_mask); 623 624 if (olen > 0) { 625 /* Autopoll response */ 626 *data = obuf[0]; 627 olen--; 628 memcpy(m->adb_data_in, &obuf[1], olen); 629 m->adb_data_in_size = olen; 630 631 s->b &= ~VIA1B_vADBInt; 632 qemu_irq_raise(m->adb_data_ready); 633 } else if (olen < 0) { 634 /* Bus timeout (device does not exist) */ 635 *data = 0xff; 636 s->b |= VIA1B_vADBInt; 637 adb_autopoll_unblock(adb_bus); 638 } else { 639 pending = adb_bus->pending & ~(1 << (m->adb_autopoll_cmd >> 4)); 640 641 if (pending) { 642 /* 643 * Bus timeout (device exists but another device has data). Block 644 * autopoll so the OS can read out the first EVEN and first ODD 645 * byte to determine bus timeout and SRQ status 646 */ 647 *data = m->adb_autopoll_cmd; 648 s->b &= ~VIA1B_vADBInt; 649 650 obuf[0] = 0xff; 651 obuf[1] = 0xff; 652 olen = 2; 653 654 memcpy(m->adb_data_in, obuf, olen); 655 m->adb_data_in_size = olen; 656 657 qemu_irq_raise(m->adb_data_ready); 658 } else { 659 /* Bus timeout (device exists but no other device has data) */ 660 *data = 0; 661 s->b |= VIA1B_vADBInt; 662 adb_autopoll_unblock(adb_bus); 663 } 664 } 665 666 trace_via1_adb_poll(*data, (s->b & VIA1B_vADBInt) ? "+" : "-", 667 adb_bus->status, m->adb_data_in_index, olen); 668 } 669 670 static int adb_via_send_len(uint8_t data) 671 { 672 /* Determine the send length from the given ADB command */ 673 uint8_t cmd = data & 0xc; 674 uint8_t reg = data & 0x3; 675 676 switch (cmd) { 677 case 0x8: 678 /* Listen command */ 679 switch (reg) { 680 case 2: 681 /* Register 2 is only used for the keyboard */ 682 return 3; 683 case 3: 684 /* 685 * Fortunately our devices only implement writes 686 * to register 3 which is fixed at 2 bytes 687 */ 688 return 3; 689 default: 690 qemu_log_mask(LOG_UNIMP, "ADB unknown length for register %d\n", 691 reg); 692 return 1; 693 } 694 default: 695 /* Talk, BusReset */ 696 return 1; 697 } 698 } 699 700 static void adb_via_send(MacVIAState *s, int state, uint8_t data) 701 { 702 MOS6522Q800VIA1State *v1s = MOS6522_Q800_VIA1(&s->mos6522_via1); 703 MOS6522State *ms = MOS6522(v1s); 704 ADBBusState *adb_bus = &s->adb_bus; 705 uint16_t autopoll_mask; 706 707 switch (state) { 708 case ADB_STATE_NEW: 709 /* 710 * Command byte: vADBInt tells host autopoll data already present 711 * in VIA shift register and ADB transceiver 712 */ 713 adb_autopoll_block(adb_bus); 714 715 if (adb_bus->status & ADB_STATUS_POLLREPLY) { 716 /* Tell the host the existing data is from autopoll */ 717 ms->b &= ~VIA1B_vADBInt; 718 } else { 719 ms->b |= VIA1B_vADBInt; 720 s->adb_data_out_index = 0; 721 s->adb_data_out[s->adb_data_out_index++] = data; 722 } 723 724 trace_via1_adb_send(" NEW", data, (ms->b & VIA1B_vADBInt) ? "+" : "-"); 725 qemu_irq_raise(s->adb_data_ready); 726 break; 727 728 case ADB_STATE_EVEN: 729 case ADB_STATE_ODD: 730 ms->b |= VIA1B_vADBInt; 731 s->adb_data_out[s->adb_data_out_index++] = data; 732 733 trace_via1_adb_send(state == ADB_STATE_EVEN ? "EVEN" : " ODD", 734 data, (ms->b & VIA1B_vADBInt) ? "+" : "-"); 735 qemu_irq_raise(s->adb_data_ready); 736 break; 737 738 case ADB_STATE_IDLE: 739 return; 740 } 741 742 /* If the command is complete, execute it */ 743 if (s->adb_data_out_index == adb_via_send_len(s->adb_data_out[0])) { 744 s->adb_data_in_size = adb_request(adb_bus, s->adb_data_in, 745 s->adb_data_out, 746 s->adb_data_out_index); 747 s->adb_data_in_index = 0; 748 749 if (adb_bus->status & ADB_STATUS_BUSTIMEOUT) { 750 /* 751 * Bus timeout (but allow first EVEN and ODD byte to indicate 752 * timeout via vADBInt and SRQ status) 753 */ 754 s->adb_data_in[0] = 0xff; 755 s->adb_data_in[1] = 0xff; 756 s->adb_data_in_size = 2; 757 } 758 759 /* 760 * If last command is TALK, store it for use by autopoll and adjust 761 * the autopoll mask accordingly 762 */ 763 if ((s->adb_data_out[0] & 0xc) == 0xc) { 764 s->adb_autopoll_cmd = s->adb_data_out[0]; 765 766 autopoll_mask = 1 << (s->adb_autopoll_cmd >> 4); 767 adb_set_autopoll_mask(adb_bus, autopoll_mask); 768 } 769 } 770 } 771 772 static void adb_via_receive(MacVIAState *s, int state, uint8_t *data) 773 { 774 MOS6522Q800VIA1State *v1s = MOS6522_Q800_VIA1(&s->mos6522_via1); 775 MOS6522State *ms = MOS6522(v1s); 776 ADBBusState *adb_bus = &s->adb_bus; 777 uint16_t pending; 778 779 switch (state) { 780 case ADB_STATE_NEW: 781 ms->b |= VIA1B_vADBInt; 782 return; 783 784 case ADB_STATE_IDLE: 785 /* 786 * Since adb_request() will have already consumed the data from the 787 * device, we must detect this extra state change and re-inject the 788 * reponse as either a "fake" autopoll reply or bus timeout 789 * accordingly 790 */ 791 if (s->adb_data_in_index == 0) { 792 if (adb_bus->status & ADB_STATUS_BUSTIMEOUT) { 793 *data = 0xff; 794 ms->b |= VIA1B_vADBInt; 795 qemu_irq_raise(s->adb_data_ready); 796 } else if (s->adb_data_in_size > 0) { 797 adb_bus->status = ADB_STATUS_POLLREPLY; 798 *data = s->adb_autopoll_cmd; 799 ms->b &= ~VIA1B_vADBInt; 800 qemu_irq_raise(s->adb_data_ready); 801 } 802 } else { 803 ms->b |= VIA1B_vADBInt; 804 adb_autopoll_unblock(adb_bus); 805 } 806 807 trace_via1_adb_receive("IDLE", *data, 808 (ms->b & VIA1B_vADBInt) ? "+" : "-", adb_bus->status, 809 s->adb_data_in_index, s->adb_data_in_size); 810 811 break; 812 813 case ADB_STATE_EVEN: 814 case ADB_STATE_ODD: 815 switch (s->adb_data_in_index) { 816 case 0: 817 /* First EVEN byte: vADBInt indicates bus timeout */ 818 trace_via1_adb_receive(state == ADB_STATE_EVEN ? "EVEN" : " ODD", 819 *data, (ms->b & VIA1B_vADBInt) ? "+" : "-", 820 adb_bus->status, s->adb_data_in_index, 821 s->adb_data_in_size); 822 823 *data = s->adb_data_in[s->adb_data_in_index++]; 824 if (adb_bus->status & ADB_STATUS_BUSTIMEOUT) { 825 ms->b &= ~VIA1B_vADBInt; 826 } else { 827 ms->b |= VIA1B_vADBInt; 828 } 829 break; 830 831 case 1: 832 /* First ODD byte: vADBInt indicates SRQ */ 833 trace_via1_adb_receive(state == ADB_STATE_EVEN ? "EVEN" : " ODD", 834 *data, (ms->b & VIA1B_vADBInt) ? "+" : "-", 835 adb_bus->status, s->adb_data_in_index, 836 s->adb_data_in_size); 837 838 *data = s->adb_data_in[s->adb_data_in_index++]; 839 pending = adb_bus->pending & ~(1 << (s->adb_autopoll_cmd >> 4)); 840 if (pending) { 841 ms->b &= ~VIA1B_vADBInt; 842 } else { 843 ms->b |= VIA1B_vADBInt; 844 } 845 break; 846 847 default: 848 /* 849 * Otherwise vADBInt indicates end of data. Note that Linux 850 * specifically checks for the sequence 0x0 0xff to confirm the 851 * end of the poll reply, so provide these extra bytes below to 852 * keep it happy 853 */ 854 trace_via1_adb_receive(state == ADB_STATE_EVEN ? "EVEN" : " ODD", 855 *data, (ms->b & VIA1B_vADBInt) ? "+" : "-", 856 adb_bus->status, s->adb_data_in_index, 857 s->adb_data_in_size); 858 859 if (s->adb_data_in_index < s->adb_data_in_size) { 860 /* Next data byte */ 861 *data = s->adb_data_in[s->adb_data_in_index++]; 862 ms->b |= VIA1B_vADBInt; 863 } else if (s->adb_data_in_index == s->adb_data_in_size) { 864 if (adb_bus->status & ADB_STATUS_BUSTIMEOUT) { 865 /* Bus timeout (no more data) */ 866 *data = 0xff; 867 } else { 868 /* Return 0x0 after reply */ 869 *data = 0; 870 } 871 s->adb_data_in_index++; 872 ms->b &= ~VIA1B_vADBInt; 873 } else { 874 /* Bus timeout (no more data) */ 875 *data = 0xff; 876 ms->b &= ~VIA1B_vADBInt; 877 adb_bus->status = 0; 878 adb_autopoll_unblock(adb_bus); 879 } 880 break; 881 } 882 883 qemu_irq_raise(s->adb_data_ready); 884 break; 885 } 886 } 887 888 static void via1_adb_update(MacVIAState *m) 889 { 890 MOS6522Q800VIA1State *v1s = MOS6522_Q800_VIA1(&m->mos6522_via1); 891 MOS6522State *s = MOS6522(v1s); 892 int oldstate, state; 893 894 oldstate = (v1s->last_b & VIA1B_vADB_StateMask) >> VIA1B_vADB_StateShift; 895 state = (s->b & VIA1B_vADB_StateMask) >> VIA1B_vADB_StateShift; 896 897 if (state != oldstate) { 898 if (s->acr & VIA1ACR_vShiftOut) { 899 /* output mode */ 900 adb_via_send(m, state, s->sr); 901 } else { 902 /* input mode */ 903 adb_via_receive(m, state, &s->sr); 904 } 905 } 906 } 907 908 static uint64_t mos6522_q800_via1_read(void *opaque, hwaddr addr, unsigned size) 909 { 910 MOS6522Q800VIA1State *s = MOS6522_Q800_VIA1(opaque); 911 MOS6522State *ms = MOS6522(s); 912 int64_t now = qemu_clock_get_ms(QEMU_CLOCK_VIRTUAL); 913 914 /* 915 * If IRQs are disabled, timers are disabled, but we need to update 916 * VIA1_IRQ_VBLANK and VIA1_IRQ_ONE_SECOND bits in the IFR 917 */ 918 919 if (now >= s->next_VBL) { 920 ms->ifr |= VIA1_IRQ_VBLANK; 921 via1_VBL_update(s); 922 } 923 if (now >= s->next_second) { 924 ms->ifr |= VIA1_IRQ_ONE_SECOND; 925 via1_one_second_update(s); 926 } 927 928 addr = (addr >> 9) & 0xf; 929 return mos6522_read(ms, addr, size); 930 } 931 932 static void mos6522_q800_via1_write(void *opaque, hwaddr addr, uint64_t val, 933 unsigned size) 934 { 935 MOS6522Q800VIA1State *v1s = MOS6522_Q800_VIA1(opaque); 936 MacVIAState *m = container_of(v1s, MacVIAState, mos6522_via1); 937 MOS6522State *ms = MOS6522(v1s); 938 939 addr = (addr >> 9) & 0xf; 940 mos6522_write(ms, addr, val, size); 941 942 switch (addr) { 943 case VIA_REG_B: 944 via1_rtc_update(m); 945 via1_adb_update(m); 946 947 v1s->last_b = ms->b; 948 break; 949 } 950 951 via1_one_second_update(v1s); 952 via1_VBL_update(v1s); 953 } 954 955 static const MemoryRegionOps mos6522_q800_via1_ops = { 956 .read = mos6522_q800_via1_read, 957 .write = mos6522_q800_via1_write, 958 .endianness = DEVICE_BIG_ENDIAN, 959 .valid = { 960 .min_access_size = 1, 961 .max_access_size = 1, 962 }, 963 }; 964 965 static uint64_t mos6522_q800_via2_read(void *opaque, hwaddr addr, unsigned size) 966 { 967 MOS6522Q800VIA2State *s = MOS6522_Q800_VIA2(opaque); 968 MOS6522State *ms = MOS6522(s); 969 970 addr = (addr >> 9) & 0xf; 971 return mos6522_read(ms, addr, size); 972 } 973 974 static void mos6522_q800_via2_write(void *opaque, hwaddr addr, uint64_t val, 975 unsigned size) 976 { 977 MOS6522Q800VIA2State *s = MOS6522_Q800_VIA2(opaque); 978 MOS6522State *ms = MOS6522(s); 979 980 addr = (addr >> 9) & 0xf; 981 mos6522_write(ms, addr, val, size); 982 } 983 984 static const MemoryRegionOps mos6522_q800_via2_ops = { 985 .read = mos6522_q800_via2_read, 986 .write = mos6522_q800_via2_write, 987 .endianness = DEVICE_BIG_ENDIAN, 988 .valid = { 989 .min_access_size = 1, 990 .max_access_size = 1, 991 }, 992 }; 993 994 static void mac_via_reset(DeviceState *dev) 995 { 996 MacVIAState *m = MAC_VIA(dev); 997 MOS6522Q800VIA1State *v1s = &m->mos6522_via1; 998 ADBBusState *adb_bus = &m->adb_bus; 999 1000 adb_set_autopoll_enabled(adb_bus, true); 1001 1002 timer_del(v1s->VBL_timer); 1003 v1s->next_VBL = 0; 1004 timer_del(v1s->one_second_timer); 1005 v1s->next_second = 0; 1006 1007 m->cmd = REG_EMPTY; 1008 m->alt = REG_EMPTY; 1009 } 1010 1011 static void mac_via_realize(DeviceState *dev, Error **errp) 1012 { 1013 MacVIAState *m = MAC_VIA(dev); 1014 MOS6522State *ms; 1015 ADBBusState *adb_bus = &m->adb_bus; 1016 struct tm tm; 1017 int ret; 1018 1019 /* Init VIAs 1 and 2 */ 1020 object_initialize_child(OBJECT(dev), "via1", &m->mos6522_via1, 1021 TYPE_MOS6522_Q800_VIA1); 1022 1023 object_initialize_child(OBJECT(dev), "via2", &m->mos6522_via2, 1024 TYPE_MOS6522_Q800_VIA2); 1025 1026 /* Pass through mos6522 output IRQs */ 1027 ms = MOS6522(&m->mos6522_via1); 1028 object_property_add_alias(OBJECT(dev), "irq[0]", OBJECT(ms), 1029 SYSBUS_DEVICE_GPIO_IRQ "[0]"); 1030 ms = MOS6522(&m->mos6522_via2); 1031 object_property_add_alias(OBJECT(dev), "irq[1]", OBJECT(ms), 1032 SYSBUS_DEVICE_GPIO_IRQ "[0]"); 1033 1034 sysbus_realize(SYS_BUS_DEVICE(&m->mos6522_via1), &error_abort); 1035 sysbus_realize(SYS_BUS_DEVICE(&m->mos6522_via2), &error_abort); 1036 1037 /* Pass through mos6522 input IRQs */ 1038 qdev_pass_gpios(DEVICE(&m->mos6522_via1), dev, "via1-irq"); 1039 qdev_pass_gpios(DEVICE(&m->mos6522_via2), dev, "via2-irq"); 1040 1041 /* VIA 1 */ 1042 m->mos6522_via1.one_second_timer = timer_new_ms(QEMU_CLOCK_VIRTUAL, 1043 via1_one_second, 1044 &m->mos6522_via1); 1045 m->mos6522_via1.VBL_timer = timer_new_ns(QEMU_CLOCK_VIRTUAL, via1_VBL, 1046 &m->mos6522_via1); 1047 1048 qemu_get_timedate(&tm, 0); 1049 m->tick_offset = (uint32_t)mktimegm(&tm) + RTC_OFFSET; 1050 1051 adb_register_autopoll_callback(adb_bus, adb_via_poll, m); 1052 m->adb_data_ready = qdev_get_gpio_in_named(dev, "via1-irq", 1053 VIA1_IRQ_ADB_READY_BIT); 1054 1055 if (m->blk) { 1056 int64_t len = blk_getlength(m->blk); 1057 if (len < 0) { 1058 error_setg_errno(errp, -len, 1059 "could not get length of backing image"); 1060 return; 1061 } 1062 ret = blk_set_perm(m->blk, 1063 BLK_PERM_CONSISTENT_READ | BLK_PERM_WRITE, 1064 BLK_PERM_ALL, errp); 1065 if (ret < 0) { 1066 return; 1067 } 1068 1069 len = blk_pread(m->blk, 0, m->mos6522_via1.PRAM, 1070 sizeof(m->mos6522_via1.PRAM)); 1071 if (len != sizeof(m->mos6522_via1.PRAM)) { 1072 error_setg(errp, "can't read PRAM contents"); 1073 return; 1074 } 1075 } 1076 } 1077 1078 static void mac_via_init(Object *obj) 1079 { 1080 SysBusDevice *sbd = SYS_BUS_DEVICE(obj); 1081 MacVIAState *m = MAC_VIA(obj); 1082 1083 /* MMIO */ 1084 memory_region_init(&m->mmio, obj, "mac-via", 2 * VIA_SIZE); 1085 sysbus_init_mmio(sbd, &m->mmio); 1086 1087 memory_region_init_io(&m->via1mem, obj, &mos6522_q800_via1_ops, 1088 &m->mos6522_via1, "via1", VIA_SIZE); 1089 memory_region_add_subregion(&m->mmio, 0x0, &m->via1mem); 1090 1091 memory_region_init_io(&m->via2mem, obj, &mos6522_q800_via2_ops, 1092 &m->mos6522_via2, "via2", VIA_SIZE); 1093 memory_region_add_subregion(&m->mmio, VIA_SIZE, &m->via2mem); 1094 1095 /* ADB */ 1096 qbus_create_inplace((BusState *)&m->adb_bus, sizeof(m->adb_bus), 1097 TYPE_ADB_BUS, DEVICE(obj), "adb.0"); 1098 } 1099 1100 static void postload_update_cb(void *opaque, int running, RunState state) 1101 { 1102 MacVIAState *m = MAC_VIA(opaque); 1103 1104 qemu_del_vm_change_state_handler(m->vmstate); 1105 m->vmstate = NULL; 1106 1107 pram_update(m); 1108 } 1109 1110 static int mac_via_post_load(void *opaque, int version_id) 1111 { 1112 MacVIAState *m = MAC_VIA(opaque); 1113 1114 if (m->blk) { 1115 m->vmstate = qemu_add_vm_change_state_handler(postload_update_cb, 1116 m); 1117 } 1118 1119 return 0; 1120 } 1121 1122 static const VMStateDescription vmstate_mac_via = { 1123 .name = "mac-via", 1124 .version_id = 2, 1125 .minimum_version_id = 2, 1126 .post_load = mac_via_post_load, 1127 .fields = (VMStateField[]) { 1128 /* VIAs */ 1129 VMSTATE_STRUCT(mos6522_via1.parent_obj, MacVIAState, 0, vmstate_mos6522, 1130 MOS6522State), 1131 VMSTATE_UINT8(mos6522_via1.last_b, MacVIAState), 1132 VMSTATE_BUFFER(mos6522_via1.PRAM, MacVIAState), 1133 VMSTATE_TIMER_PTR(mos6522_via1.one_second_timer, MacVIAState), 1134 VMSTATE_INT64(mos6522_via1.next_second, MacVIAState), 1135 VMSTATE_TIMER_PTR(mos6522_via1.VBL_timer, MacVIAState), 1136 VMSTATE_INT64(mos6522_via1.next_VBL, MacVIAState), 1137 VMSTATE_STRUCT(mos6522_via2.parent_obj, MacVIAState, 0, vmstate_mos6522, 1138 MOS6522State), 1139 /* RTC */ 1140 VMSTATE_UINT32(tick_offset, MacVIAState), 1141 VMSTATE_UINT8(data_out, MacVIAState), 1142 VMSTATE_INT32(data_out_cnt, MacVIAState), 1143 VMSTATE_UINT8(data_in, MacVIAState), 1144 VMSTATE_UINT8(data_in_cnt, MacVIAState), 1145 VMSTATE_UINT8(cmd, MacVIAState), 1146 VMSTATE_INT32(wprotect, MacVIAState), 1147 VMSTATE_INT32(alt, MacVIAState), 1148 /* ADB */ 1149 VMSTATE_INT32(adb_data_in_size, MacVIAState), 1150 VMSTATE_INT32(adb_data_in_index, MacVIAState), 1151 VMSTATE_INT32(adb_data_out_index, MacVIAState), 1152 VMSTATE_BUFFER(adb_data_in, MacVIAState), 1153 VMSTATE_BUFFER(adb_data_out, MacVIAState), 1154 VMSTATE_UINT8(adb_autopoll_cmd, MacVIAState), 1155 VMSTATE_END_OF_LIST() 1156 } 1157 }; 1158 1159 static Property mac_via_properties[] = { 1160 DEFINE_PROP_DRIVE("drive", MacVIAState, blk), 1161 DEFINE_PROP_END_OF_LIST(), 1162 }; 1163 1164 static void mac_via_class_init(ObjectClass *oc, void *data) 1165 { 1166 DeviceClass *dc = DEVICE_CLASS(oc); 1167 1168 dc->realize = mac_via_realize; 1169 dc->reset = mac_via_reset; 1170 dc->vmsd = &vmstate_mac_via; 1171 device_class_set_props(dc, mac_via_properties); 1172 } 1173 1174 static TypeInfo mac_via_info = { 1175 .name = TYPE_MAC_VIA, 1176 .parent = TYPE_SYS_BUS_DEVICE, 1177 .instance_size = sizeof(MacVIAState), 1178 .instance_init = mac_via_init, 1179 .class_init = mac_via_class_init, 1180 }; 1181 1182 /* VIA 1 */ 1183 static void mos6522_q800_via1_reset(DeviceState *dev) 1184 { 1185 MOS6522State *ms = MOS6522(dev); 1186 MOS6522DeviceClass *mdc = MOS6522_DEVICE_GET_CLASS(ms); 1187 1188 mdc->parent_reset(dev); 1189 1190 ms->timers[0].frequency = VIA_TIMER_FREQ; 1191 ms->timers[1].frequency = VIA_TIMER_FREQ; 1192 1193 ms->b = VIA1B_vADB_StateMask | VIA1B_vADBInt | VIA1B_vRTCEnb; 1194 } 1195 1196 static void mos6522_q800_via1_init(Object *obj) 1197 { 1198 qdev_init_gpio_in_named(DEVICE(obj), via1_irq_request, "via1-irq", 1199 VIA1_IRQ_NB); 1200 } 1201 1202 static void mos6522_q800_via1_class_init(ObjectClass *oc, void *data) 1203 { 1204 DeviceClass *dc = DEVICE_CLASS(oc); 1205 1206 dc->reset = mos6522_q800_via1_reset; 1207 } 1208 1209 static const TypeInfo mos6522_q800_via1_type_info = { 1210 .name = TYPE_MOS6522_Q800_VIA1, 1211 .parent = TYPE_MOS6522, 1212 .instance_size = sizeof(MOS6522Q800VIA1State), 1213 .instance_init = mos6522_q800_via1_init, 1214 .class_init = mos6522_q800_via1_class_init, 1215 }; 1216 1217 /* VIA 2 */ 1218 static void mos6522_q800_via2_portB_write(MOS6522State *s) 1219 { 1220 if (s->dirb & VIA2B_vPower && (s->b & VIA2B_vPower) == 0) { 1221 /* shutdown */ 1222 qemu_system_shutdown_request(SHUTDOWN_CAUSE_GUEST_SHUTDOWN); 1223 } 1224 } 1225 1226 static void mos6522_q800_via2_reset(DeviceState *dev) 1227 { 1228 MOS6522State *ms = MOS6522(dev); 1229 MOS6522DeviceClass *mdc = MOS6522_DEVICE_GET_CLASS(ms); 1230 1231 mdc->parent_reset(dev); 1232 1233 ms->timers[0].frequency = VIA_TIMER_FREQ; 1234 ms->timers[1].frequency = VIA_TIMER_FREQ; 1235 1236 ms->dirb = 0; 1237 ms->b = 0; 1238 } 1239 1240 static void mos6522_q800_via2_init(Object *obj) 1241 { 1242 qdev_init_gpio_in_named(DEVICE(obj), via2_irq_request, "via2-irq", 1243 VIA2_IRQ_NB); 1244 } 1245 1246 static void mos6522_q800_via2_class_init(ObjectClass *oc, void *data) 1247 { 1248 DeviceClass *dc = DEVICE_CLASS(oc); 1249 MOS6522DeviceClass *mdc = MOS6522_DEVICE_CLASS(oc); 1250 1251 dc->reset = mos6522_q800_via2_reset; 1252 mdc->portB_write = mos6522_q800_via2_portB_write; 1253 } 1254 1255 static const TypeInfo mos6522_q800_via2_type_info = { 1256 .name = TYPE_MOS6522_Q800_VIA2, 1257 .parent = TYPE_MOS6522, 1258 .instance_size = sizeof(MOS6522Q800VIA2State), 1259 .instance_init = mos6522_q800_via2_init, 1260 .class_init = mos6522_q800_via2_class_init, 1261 }; 1262 1263 static void mac_via_register_types(void) 1264 { 1265 type_register_static(&mos6522_q800_via1_type_info); 1266 type_register_static(&mos6522_q800_via2_type_info); 1267 type_register_static(&mac_via_info); 1268 } 1269 1270 type_init(mac_via_register_types); 1271