1 /* 2 * National Semiconductor LM8322/8323 GPIO keyboard & PWM chips. 3 * 4 * Copyright (C) 2008 Nokia Corporation 5 * Written by Andrzej Zaborowski <andrew@openedhand.com> 6 * 7 * This program is free software; you can redistribute it and/or 8 * modify it under the terms of the GNU General Public License as 9 * published by the Free Software Foundation; either version 2 or 10 * (at your option) version 3 of the License. 11 * 12 * This program is distributed in the hope that it will be useful, 13 * but WITHOUT ANY WARRANTY; without even the implied warranty of 14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 15 * GNU General Public License for more details. 16 * 17 * You should have received a copy of the GNU General Public License along 18 * with this program; if not, see <http://www.gnu.org/licenses/>. 19 */ 20 21 #include "qemu/osdep.h" 22 #include "hw/hw.h" 23 #include "hw/i2c/i2c.h" 24 #include "qemu/timer.h" 25 #include "ui/console.h" 26 27 #define TYPE_LM8323 "lm8323" 28 #define LM8323(obj) OBJECT_CHECK(LM823KbdState, (obj), TYPE_LM8323) 29 30 typedef struct { 31 I2CSlave parent_obj; 32 33 uint8_t i2c_dir; 34 uint8_t i2c_cycle; 35 uint8_t reg; 36 37 qemu_irq nirq; 38 uint16_t model; 39 40 struct { 41 qemu_irq out[2]; 42 int in[2][2]; 43 } mux; 44 45 uint8_t config; 46 uint8_t status; 47 uint8_t acttime; 48 uint8_t error; 49 uint8_t clock; 50 51 struct { 52 uint16_t pull; 53 uint16_t mask; 54 uint16_t dir; 55 uint16_t level; 56 qemu_irq out[16]; 57 } gpio; 58 59 struct { 60 uint8_t dbnctime; 61 uint8_t size; 62 uint8_t start; 63 uint8_t len; 64 uint8_t fifo[16]; 65 } kbd; 66 67 struct { 68 uint16_t file[256]; 69 uint8_t faddr; 70 uint8_t addr[3]; 71 QEMUTimer *tm[3]; 72 } pwm; 73 } LM823KbdState; 74 75 #define INT_KEYPAD (1 << 0) 76 #define INT_ERROR (1 << 3) 77 #define INT_NOINIT (1 << 4) 78 #define INT_PWMEND(n) (1 << (5 + n)) 79 80 #define ERR_BADPAR (1 << 0) 81 #define ERR_CMDUNK (1 << 1) 82 #define ERR_KEYOVR (1 << 2) 83 #define ERR_FIFOOVR (1 << 6) 84 85 static void lm_kbd_irq_update(LM823KbdState *s) 86 { 87 qemu_set_irq(s->nirq, !s->status); 88 } 89 90 static void lm_kbd_gpio_update(LM823KbdState *s) 91 { 92 } 93 94 static void lm_kbd_reset(LM823KbdState *s) 95 { 96 s->config = 0x80; 97 s->status = INT_NOINIT; 98 s->acttime = 125; 99 s->kbd.dbnctime = 3; 100 s->kbd.size = 0x33; 101 s->clock = 0x08; 102 103 lm_kbd_irq_update(s); 104 lm_kbd_gpio_update(s); 105 } 106 107 static void lm_kbd_error(LM823KbdState *s, int err) 108 { 109 s->error |= err; 110 s->status |= INT_ERROR; 111 lm_kbd_irq_update(s); 112 } 113 114 static void lm_kbd_pwm_tick(LM823KbdState *s, int line) 115 { 116 } 117 118 static void lm_kbd_pwm_start(LM823KbdState *s, int line) 119 { 120 lm_kbd_pwm_tick(s, line); 121 } 122 123 static void lm_kbd_pwm0_tick(void *opaque) 124 { 125 lm_kbd_pwm_tick(opaque, 0); 126 } 127 static void lm_kbd_pwm1_tick(void *opaque) 128 { 129 lm_kbd_pwm_tick(opaque, 1); 130 } 131 static void lm_kbd_pwm2_tick(void *opaque) 132 { 133 lm_kbd_pwm_tick(opaque, 2); 134 } 135 136 enum { 137 LM832x_CMD_READ_ID = 0x80, /* Read chip ID. */ 138 LM832x_CMD_WRITE_CFG = 0x81, /* Set configuration item. */ 139 LM832x_CMD_READ_INT = 0x82, /* Get interrupt status. */ 140 LM832x_CMD_RESET = 0x83, /* Reset, same as external one */ 141 LM823x_CMD_WRITE_PULL_DOWN = 0x84, /* Select GPIO pull-up/down. */ 142 LM832x_CMD_WRITE_PORT_SEL = 0x85, /* Select GPIO in/out. */ 143 LM832x_CMD_WRITE_PORT_STATE = 0x86, /* Set GPIO pull-up/down. */ 144 LM832x_CMD_READ_PORT_SEL = 0x87, /* Get GPIO in/out. */ 145 LM832x_CMD_READ_PORT_STATE = 0x88, /* Get GPIO pull-up/down. */ 146 LM832x_CMD_READ_FIFO = 0x89, /* Read byte from FIFO. */ 147 LM832x_CMD_RPT_READ_FIFO = 0x8a, /* Read FIFO (no increment). */ 148 LM832x_CMD_SET_ACTIVE = 0x8b, /* Set active time. */ 149 LM832x_CMD_READ_ERROR = 0x8c, /* Get error status. */ 150 LM832x_CMD_READ_ROTATOR = 0x8e, /* Read rotator status. */ 151 LM832x_CMD_SET_DEBOUNCE = 0x8f, /* Set debouncing time. */ 152 LM832x_CMD_SET_KEY_SIZE = 0x90, /* Set keypad size. */ 153 LM832x_CMD_READ_KEY_SIZE = 0x91, /* Get keypad size. */ 154 LM832x_CMD_READ_CFG = 0x92, /* Get configuration item. */ 155 LM832x_CMD_WRITE_CLOCK = 0x93, /* Set clock config. */ 156 LM832x_CMD_READ_CLOCK = 0x94, /* Get clock config. */ 157 LM832x_CMD_PWM_WRITE = 0x95, /* Write PWM script. */ 158 LM832x_CMD_PWM_START = 0x96, /* Start PWM engine. */ 159 LM832x_CMD_PWM_STOP = 0x97, /* Stop PWM engine. */ 160 LM832x_GENERAL_ERROR = 0xff, /* There was one error. 161 Previously was represented by -1 162 This is not a command */ 163 }; 164 165 #define LM832x_MAX_KPX 8 166 #define LM832x_MAX_KPY 12 167 168 static uint8_t lm_kbd_read(LM823KbdState *s, int reg, int byte) 169 { 170 int ret; 171 172 switch (reg) { 173 case LM832x_CMD_READ_ID: 174 ret = 0x0400; 175 break; 176 177 case LM832x_CMD_READ_INT: 178 ret = s->status; 179 if (!(s->status & INT_NOINIT)) { 180 s->status = 0; 181 lm_kbd_irq_update(s); 182 } 183 break; 184 185 case LM832x_CMD_READ_PORT_SEL: 186 ret = s->gpio.dir; 187 break; 188 case LM832x_CMD_READ_PORT_STATE: 189 ret = s->gpio.mask; 190 break; 191 192 case LM832x_CMD_READ_FIFO: 193 if (s->kbd.len <= 1) 194 return 0x00; 195 196 /* Example response from the two commands after a INT_KEYPAD 197 * interrupt caused by the key 0x3c being pressed: 198 * RPT_READ_FIFO: 55 bc 00 4e ff 0a 50 08 00 29 d9 08 01 c9 01 199 * READ_FIFO: bc 00 00 4e ff 0a 50 08 00 29 d9 08 01 c9 01 200 * RPT_READ_FIFO: bc 00 00 4e ff 0a 50 08 00 29 d9 08 01 c9 01 201 * 202 * 55 is the code of the key release event serviced in the previous 203 * interrupt handling. 204 * 205 * TODO: find out whether the FIFO is advanced a single character 206 * before reading every byte or the whole size of the FIFO at the 207 * last LM832x_CMD_READ_FIFO. This affects LM832x_CMD_RPT_READ_FIFO 208 * output in cases where there are more than one event in the FIFO. 209 * Assume 0xbc and 0x3c events are in the FIFO: 210 * RPT_READ_FIFO: 55 bc 3c 00 4e ff 0a 50 08 00 29 d9 08 01 c9 211 * READ_FIFO: bc 3c 00 00 4e ff 0a 50 08 00 29 d9 08 01 c9 212 * Does RPT_READ_FIFO now return 0xbc and 0x3c or only 0x3c? 213 */ 214 s->kbd.start ++; 215 s->kbd.start &= sizeof(s->kbd.fifo) - 1; 216 s->kbd.len --; 217 218 return s->kbd.fifo[s->kbd.start]; 219 case LM832x_CMD_RPT_READ_FIFO: 220 if (byte >= s->kbd.len) 221 return 0x00; 222 223 return s->kbd.fifo[(s->kbd.start + byte) & (sizeof(s->kbd.fifo) - 1)]; 224 225 case LM832x_CMD_READ_ERROR: 226 return s->error; 227 228 case LM832x_CMD_READ_ROTATOR: 229 return 0; 230 231 case LM832x_CMD_READ_KEY_SIZE: 232 return s->kbd.size; 233 234 case LM832x_CMD_READ_CFG: 235 return s->config & 0xf; 236 237 case LM832x_CMD_READ_CLOCK: 238 return (s->clock & 0xfc) | 2; 239 240 default: 241 lm_kbd_error(s, ERR_CMDUNK); 242 fprintf(stderr, "%s: unknown command %02x\n", __func__, reg); 243 return 0x00; 244 } 245 246 return ret >> (byte << 3); 247 } 248 249 static void lm_kbd_write(LM823KbdState *s, int reg, int byte, uint8_t value) 250 { 251 switch (reg) { 252 case LM832x_CMD_WRITE_CFG: 253 s->config = value; 254 /* This must be done whenever s->mux.in is updated (never). */ 255 if ((s->config >> 1) & 1) /* MUX1EN */ 256 qemu_set_irq(s->mux.out[0], s->mux.in[0][(s->config >> 0) & 1]); 257 if ((s->config >> 3) & 1) /* MUX2EN */ 258 qemu_set_irq(s->mux.out[0], s->mux.in[0][(s->config >> 2) & 1]); 259 /* TODO: check that this is issued only following the chip reset 260 * and not in the middle of operation and that it is followed by 261 * the GPIO ports re-resablishing through WRITE_PORT_SEL and 262 * WRITE_PORT_STATE (using a timer perhaps) and otherwise output 263 * warnings. */ 264 s->status = 0; 265 lm_kbd_irq_update(s); 266 s->kbd.len = 0; 267 s->kbd.start = 0; 268 s->reg = LM832x_GENERAL_ERROR; 269 break; 270 271 case LM832x_CMD_RESET: 272 if (value == 0xaa) 273 lm_kbd_reset(s); 274 else 275 lm_kbd_error(s, ERR_BADPAR); 276 s->reg = LM832x_GENERAL_ERROR; 277 break; 278 279 case LM823x_CMD_WRITE_PULL_DOWN: 280 if (!byte) 281 s->gpio.pull = value; 282 else { 283 s->gpio.pull |= value << 8; 284 lm_kbd_gpio_update(s); 285 s->reg = LM832x_GENERAL_ERROR; 286 } 287 break; 288 case LM832x_CMD_WRITE_PORT_SEL: 289 if (!byte) 290 s->gpio.dir = value; 291 else { 292 s->gpio.dir |= value << 8; 293 lm_kbd_gpio_update(s); 294 s->reg = LM832x_GENERAL_ERROR; 295 } 296 break; 297 case LM832x_CMD_WRITE_PORT_STATE: 298 if (!byte) 299 s->gpio.mask = value; 300 else { 301 s->gpio.mask |= value << 8; 302 lm_kbd_gpio_update(s); 303 s->reg = LM832x_GENERAL_ERROR; 304 } 305 break; 306 307 case LM832x_CMD_SET_ACTIVE: 308 s->acttime = value; 309 s->reg = LM832x_GENERAL_ERROR; 310 break; 311 312 case LM832x_CMD_SET_DEBOUNCE: 313 s->kbd.dbnctime = value; 314 s->reg = LM832x_GENERAL_ERROR; 315 if (!value) 316 lm_kbd_error(s, ERR_BADPAR); 317 break; 318 319 case LM832x_CMD_SET_KEY_SIZE: 320 s->kbd.size = value; 321 s->reg = LM832x_GENERAL_ERROR; 322 if ( 323 (value & 0xf) < 3 || (value & 0xf) > LM832x_MAX_KPY || 324 (value >> 4) < 3 || (value >> 4) > LM832x_MAX_KPX) 325 lm_kbd_error(s, ERR_BADPAR); 326 break; 327 328 case LM832x_CMD_WRITE_CLOCK: 329 s->clock = value; 330 s->reg = LM832x_GENERAL_ERROR; 331 if ((value & 3) && (value & 3) != 3) { 332 lm_kbd_error(s, ERR_BADPAR); 333 fprintf(stderr, "%s: invalid clock setting in RCPWM\n", 334 __func__); 335 } 336 /* TODO: Validate that the command is only issued once */ 337 break; 338 339 case LM832x_CMD_PWM_WRITE: 340 if (byte == 0) { 341 if (!(value & 3) || (value >> 2) > 59) { 342 lm_kbd_error(s, ERR_BADPAR); 343 s->reg = LM832x_GENERAL_ERROR; 344 break; 345 } 346 347 s->pwm.faddr = value; 348 s->pwm.file[s->pwm.faddr] = 0; 349 } else if (byte == 1) { 350 s->pwm.file[s->pwm.faddr] |= value << 8; 351 } else if (byte == 2) { 352 s->pwm.file[s->pwm.faddr] |= value << 0; 353 s->reg = LM832x_GENERAL_ERROR; 354 } 355 break; 356 case LM832x_CMD_PWM_START: 357 s->reg = LM832x_GENERAL_ERROR; 358 if (!(value & 3) || (value >> 2) > 59) { 359 lm_kbd_error(s, ERR_BADPAR); 360 break; 361 } 362 363 s->pwm.addr[(value & 3) - 1] = value >> 2; 364 lm_kbd_pwm_start(s, (value & 3) - 1); 365 break; 366 case LM832x_CMD_PWM_STOP: 367 s->reg = LM832x_GENERAL_ERROR; 368 if (!(value & 3)) { 369 lm_kbd_error(s, ERR_BADPAR); 370 break; 371 } 372 373 timer_del(s->pwm.tm[(value & 3) - 1]); 374 break; 375 376 case LM832x_GENERAL_ERROR: 377 lm_kbd_error(s, ERR_BADPAR); 378 break; 379 default: 380 lm_kbd_error(s, ERR_CMDUNK); 381 fprintf(stderr, "%s: unknown command %02x\n", __func__, reg); 382 break; 383 } 384 } 385 386 static int lm_i2c_event(I2CSlave *i2c, enum i2c_event event) 387 { 388 LM823KbdState *s = LM8323(i2c); 389 390 switch (event) { 391 case I2C_START_RECV: 392 case I2C_START_SEND: 393 s->i2c_cycle = 0; 394 s->i2c_dir = (event == I2C_START_SEND); 395 break; 396 397 default: 398 break; 399 } 400 401 return 0; 402 } 403 404 static uint8_t lm_i2c_rx(I2CSlave *i2c) 405 { 406 LM823KbdState *s = LM8323(i2c); 407 408 return lm_kbd_read(s, s->reg, s->i2c_cycle ++); 409 } 410 411 static int lm_i2c_tx(I2CSlave *i2c, uint8_t data) 412 { 413 LM823KbdState *s = LM8323(i2c); 414 415 if (!s->i2c_cycle) 416 s->reg = data; 417 else 418 lm_kbd_write(s, s->reg, s->i2c_cycle - 1, data); 419 s->i2c_cycle ++; 420 421 return 0; 422 } 423 424 static int lm_kbd_post_load(void *opaque, int version_id) 425 { 426 LM823KbdState *s = opaque; 427 428 lm_kbd_irq_update(s); 429 lm_kbd_gpio_update(s); 430 431 return 0; 432 } 433 434 static const VMStateDescription vmstate_lm_kbd = { 435 .name = "LM8323", 436 .version_id = 0, 437 .minimum_version_id = 0, 438 .post_load = lm_kbd_post_load, 439 .fields = (VMStateField[]) { 440 VMSTATE_I2C_SLAVE(parent_obj, LM823KbdState), 441 VMSTATE_UINT8(i2c_dir, LM823KbdState), 442 VMSTATE_UINT8(i2c_cycle, LM823KbdState), 443 VMSTATE_UINT8(reg, LM823KbdState), 444 VMSTATE_UINT8(config, LM823KbdState), 445 VMSTATE_UINT8(status, LM823KbdState), 446 VMSTATE_UINT8(acttime, LM823KbdState), 447 VMSTATE_UINT8(error, LM823KbdState), 448 VMSTATE_UINT8(clock, LM823KbdState), 449 VMSTATE_UINT16(gpio.pull, LM823KbdState), 450 VMSTATE_UINT16(gpio.mask, LM823KbdState), 451 VMSTATE_UINT16(gpio.dir, LM823KbdState), 452 VMSTATE_UINT16(gpio.level, LM823KbdState), 453 VMSTATE_UINT8(kbd.dbnctime, LM823KbdState), 454 VMSTATE_UINT8(kbd.size, LM823KbdState), 455 VMSTATE_UINT8(kbd.start, LM823KbdState), 456 VMSTATE_UINT8(kbd.len, LM823KbdState), 457 VMSTATE_BUFFER(kbd.fifo, LM823KbdState), 458 VMSTATE_UINT16_ARRAY(pwm.file, LM823KbdState, 256), 459 VMSTATE_UINT8(pwm.faddr, LM823KbdState), 460 VMSTATE_BUFFER(pwm.addr, LM823KbdState), 461 VMSTATE_TIMER_PTR_ARRAY(pwm.tm, LM823KbdState, 3), 462 VMSTATE_END_OF_LIST() 463 } 464 }; 465 466 467 static void lm8323_realize(DeviceState *dev, Error **errp) 468 { 469 LM823KbdState *s = LM8323(dev); 470 471 s->model = 0x8323; 472 s->pwm.tm[0] = timer_new_ns(QEMU_CLOCK_VIRTUAL, lm_kbd_pwm0_tick, s); 473 s->pwm.tm[1] = timer_new_ns(QEMU_CLOCK_VIRTUAL, lm_kbd_pwm1_tick, s); 474 s->pwm.tm[2] = timer_new_ns(QEMU_CLOCK_VIRTUAL, lm_kbd_pwm2_tick, s); 475 qdev_init_gpio_out(dev, &s->nirq, 1); 476 477 lm_kbd_reset(s); 478 479 qemu_register_reset((void *) lm_kbd_reset, s); 480 } 481 482 void lm832x_key_event(DeviceState *dev, int key, int state) 483 { 484 LM823KbdState *s = LM8323(dev); 485 486 if ((s->status & INT_ERROR) && (s->error & ERR_FIFOOVR)) 487 return; 488 489 if (s->kbd.len >= sizeof(s->kbd.fifo)) { 490 lm_kbd_error(s, ERR_FIFOOVR); 491 return; 492 } 493 494 s->kbd.fifo[(s->kbd.start + s->kbd.len ++) & (sizeof(s->kbd.fifo) - 1)] = 495 key | (state << 7); 496 497 /* We never set ERR_KEYOVR because we support multiple keys fine. */ 498 s->status |= INT_KEYPAD; 499 lm_kbd_irq_update(s); 500 } 501 502 static void lm8323_class_init(ObjectClass *klass, void *data) 503 { 504 DeviceClass *dc = DEVICE_CLASS(klass); 505 I2CSlaveClass *k = I2C_SLAVE_CLASS(klass); 506 507 dc->realize = lm8323_realize; 508 k->event = lm_i2c_event; 509 k->recv = lm_i2c_rx; 510 k->send = lm_i2c_tx; 511 dc->vmsd = &vmstate_lm_kbd; 512 } 513 514 static const TypeInfo lm8323_info = { 515 .name = TYPE_LM8323, 516 .parent = TYPE_I2C_SLAVE, 517 .instance_size = sizeof(LM823KbdState), 518 .class_init = lm8323_class_init, 519 }; 520 521 static void lm832x_register_types(void) 522 { 523 type_register_static(&lm8323_info); 524 } 525 526 type_init(lm832x_register_types) 527