1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 */ 4 5 #include <linux/init.h> 6 #include <linux/slab.h> 7 #include <linux/usb.h> 8 #include <linux/usb/audio.h> 9 #include <linux/usb/midi.h> 10 #include <linux/bits.h> 11 12 #include <sound/control.h> 13 #include <sound/core.h> 14 #include <sound/info.h> 15 #include <sound/pcm.h> 16 17 #include "usbaudio.h" 18 #include "card.h" 19 #include "mixer.h" 20 #include "mixer_quirks.h" 21 #include "midi.h" 22 #include "quirks.h" 23 #include "helper.h" 24 #include "endpoint.h" 25 #include "pcm.h" 26 #include "clock.h" 27 #include "stream.h" 28 29 /* 30 * handle the quirks for the contained interfaces 31 */ 32 static int create_composite_quirk(struct snd_usb_audio *chip, 33 struct usb_interface *iface, 34 struct usb_driver *driver, 35 const struct snd_usb_audio_quirk *quirk_comp) 36 { 37 int probed_ifnum = get_iface_desc(iface->altsetting)->bInterfaceNumber; 38 const struct snd_usb_audio_quirk *quirk; 39 int err; 40 41 for (quirk = quirk_comp->data; quirk->ifnum >= 0; ++quirk) { 42 iface = usb_ifnum_to_if(chip->dev, quirk->ifnum); 43 if (!iface) 44 continue; 45 if (quirk->ifnum != probed_ifnum && 46 usb_interface_claimed(iface)) 47 continue; 48 err = snd_usb_create_quirk(chip, iface, driver, quirk); 49 if (err < 0) 50 return err; 51 } 52 53 for (quirk = quirk_comp->data; quirk->ifnum >= 0; ++quirk) { 54 iface = usb_ifnum_to_if(chip->dev, quirk->ifnum); 55 if (!iface) 56 continue; 57 if (quirk->ifnum != probed_ifnum && 58 !usb_interface_claimed(iface)) 59 usb_driver_claim_interface(driver, iface, (void *)-1L); 60 } 61 62 return 0; 63 } 64 65 static int ignore_interface_quirk(struct snd_usb_audio *chip, 66 struct usb_interface *iface, 67 struct usb_driver *driver, 68 const struct snd_usb_audio_quirk *quirk) 69 { 70 return 0; 71 } 72 73 74 /* 75 * Allow alignment on audio sub-slot (channel samples) rather than 76 * on audio slots (audio frames) 77 */ 78 static int create_align_transfer_quirk(struct snd_usb_audio *chip, 79 struct usb_interface *iface, 80 struct usb_driver *driver, 81 const struct snd_usb_audio_quirk *quirk) 82 { 83 chip->txfr_quirk = 1; 84 return 1; /* Continue with creating streams and mixer */ 85 } 86 87 static int create_any_midi_quirk(struct snd_usb_audio *chip, 88 struct usb_interface *intf, 89 struct usb_driver *driver, 90 const struct snd_usb_audio_quirk *quirk) 91 { 92 return snd_usbmidi_create(chip->card, intf, &chip->midi_list, quirk); 93 } 94 95 /* 96 * create a stream for an interface with proper descriptors 97 */ 98 static int create_standard_audio_quirk(struct snd_usb_audio *chip, 99 struct usb_interface *iface, 100 struct usb_driver *driver, 101 const struct snd_usb_audio_quirk *quirk) 102 { 103 struct usb_host_interface *alts; 104 struct usb_interface_descriptor *altsd; 105 int err; 106 107 if (chip->usb_id == USB_ID(0x1686, 0x00dd)) /* Zoom R16/24 */ 108 chip->tx_length_quirk = 1; 109 110 alts = &iface->altsetting[0]; 111 altsd = get_iface_desc(alts); 112 err = snd_usb_parse_audio_interface(chip, altsd->bInterfaceNumber); 113 if (err < 0) { 114 usb_audio_err(chip, "cannot setup if %d: error %d\n", 115 altsd->bInterfaceNumber, err); 116 return err; 117 } 118 /* reset the current interface */ 119 usb_set_interface(chip->dev, altsd->bInterfaceNumber, 0); 120 return 0; 121 } 122 123 /* 124 * create a stream for an endpoint/altsetting without proper descriptors 125 */ 126 static int create_fixed_stream_quirk(struct snd_usb_audio *chip, 127 struct usb_interface *iface, 128 struct usb_driver *driver, 129 const struct snd_usb_audio_quirk *quirk) 130 { 131 struct audioformat *fp; 132 struct usb_host_interface *alts; 133 struct usb_interface_descriptor *altsd; 134 int stream, err; 135 unsigned *rate_table = NULL; 136 137 fp = kmemdup(quirk->data, sizeof(*fp), GFP_KERNEL); 138 if (!fp) 139 return -ENOMEM; 140 141 INIT_LIST_HEAD(&fp->list); 142 if (fp->nr_rates > MAX_NR_RATES) { 143 kfree(fp); 144 return -EINVAL; 145 } 146 if (fp->nr_rates > 0) { 147 rate_table = kmemdup(fp->rate_table, 148 sizeof(int) * fp->nr_rates, GFP_KERNEL); 149 if (!rate_table) { 150 kfree(fp); 151 return -ENOMEM; 152 } 153 fp->rate_table = rate_table; 154 } 155 156 stream = (fp->endpoint & USB_DIR_IN) 157 ? SNDRV_PCM_STREAM_CAPTURE : SNDRV_PCM_STREAM_PLAYBACK; 158 err = snd_usb_add_audio_stream(chip, stream, fp); 159 if (err < 0) 160 goto error; 161 if (fp->iface != get_iface_desc(&iface->altsetting[0])->bInterfaceNumber || 162 fp->altset_idx >= iface->num_altsetting) { 163 err = -EINVAL; 164 goto error; 165 } 166 alts = &iface->altsetting[fp->altset_idx]; 167 altsd = get_iface_desc(alts); 168 if (altsd->bNumEndpoints < 1) { 169 err = -EINVAL; 170 goto error; 171 } 172 173 fp->protocol = altsd->bInterfaceProtocol; 174 175 if (fp->datainterval == 0) 176 fp->datainterval = snd_usb_parse_datainterval(chip, alts); 177 if (fp->maxpacksize == 0) 178 fp->maxpacksize = le16_to_cpu(get_endpoint(alts, 0)->wMaxPacketSize); 179 usb_set_interface(chip->dev, fp->iface, 0); 180 snd_usb_init_pitch(chip, fp); 181 snd_usb_init_sample_rate(chip, fp, fp->rate_max); 182 return 0; 183 184 error: 185 list_del(&fp->list); /* unlink for avoiding double-free */ 186 kfree(fp); 187 kfree(rate_table); 188 return err; 189 } 190 191 static int create_auto_pcm_quirk(struct snd_usb_audio *chip, 192 struct usb_interface *iface, 193 struct usb_driver *driver) 194 { 195 struct usb_host_interface *alts; 196 struct usb_interface_descriptor *altsd; 197 struct usb_endpoint_descriptor *epd; 198 struct uac1_as_header_descriptor *ashd; 199 struct uac_format_type_i_discrete_descriptor *fmtd; 200 201 /* 202 * Most Roland/Yamaha audio streaming interfaces have more or less 203 * standard descriptors, but older devices might lack descriptors, and 204 * future ones might change, so ensure that we fail silently if the 205 * interface doesn't look exactly right. 206 */ 207 208 /* must have a non-zero altsetting for streaming */ 209 if (iface->num_altsetting < 2) 210 return -ENODEV; 211 alts = &iface->altsetting[1]; 212 altsd = get_iface_desc(alts); 213 214 /* must have an isochronous endpoint for streaming */ 215 if (altsd->bNumEndpoints < 1) 216 return -ENODEV; 217 epd = get_endpoint(alts, 0); 218 if (!usb_endpoint_xfer_isoc(epd)) 219 return -ENODEV; 220 221 /* must have format descriptors */ 222 ashd = snd_usb_find_csint_desc(alts->extra, alts->extralen, NULL, 223 UAC_AS_GENERAL); 224 fmtd = snd_usb_find_csint_desc(alts->extra, alts->extralen, NULL, 225 UAC_FORMAT_TYPE); 226 if (!ashd || ashd->bLength < 7 || 227 !fmtd || fmtd->bLength < 8) 228 return -ENODEV; 229 230 return create_standard_audio_quirk(chip, iface, driver, NULL); 231 } 232 233 static int create_yamaha_midi_quirk(struct snd_usb_audio *chip, 234 struct usb_interface *iface, 235 struct usb_driver *driver, 236 struct usb_host_interface *alts) 237 { 238 static const struct snd_usb_audio_quirk yamaha_midi_quirk = { 239 .type = QUIRK_MIDI_YAMAHA 240 }; 241 struct usb_midi_in_jack_descriptor *injd; 242 struct usb_midi_out_jack_descriptor *outjd; 243 244 /* must have some valid jack descriptors */ 245 injd = snd_usb_find_csint_desc(alts->extra, alts->extralen, 246 NULL, USB_MS_MIDI_IN_JACK); 247 outjd = snd_usb_find_csint_desc(alts->extra, alts->extralen, 248 NULL, USB_MS_MIDI_OUT_JACK); 249 if (!injd && !outjd) 250 return -ENODEV; 251 if ((injd && !snd_usb_validate_midi_desc(injd)) || 252 (outjd && !snd_usb_validate_midi_desc(outjd))) 253 return -ENODEV; 254 if (injd && (injd->bLength < 5 || 255 (injd->bJackType != USB_MS_EMBEDDED && 256 injd->bJackType != USB_MS_EXTERNAL))) 257 return -ENODEV; 258 if (outjd && (outjd->bLength < 6 || 259 (outjd->bJackType != USB_MS_EMBEDDED && 260 outjd->bJackType != USB_MS_EXTERNAL))) 261 return -ENODEV; 262 return create_any_midi_quirk(chip, iface, driver, &yamaha_midi_quirk); 263 } 264 265 static int create_roland_midi_quirk(struct snd_usb_audio *chip, 266 struct usb_interface *iface, 267 struct usb_driver *driver, 268 struct usb_host_interface *alts) 269 { 270 static const struct snd_usb_audio_quirk roland_midi_quirk = { 271 .type = QUIRK_MIDI_ROLAND 272 }; 273 u8 *roland_desc = NULL; 274 275 /* might have a vendor-specific descriptor <06 24 F1 02 ...> */ 276 for (;;) { 277 roland_desc = snd_usb_find_csint_desc(alts->extra, 278 alts->extralen, 279 roland_desc, 0xf1); 280 if (!roland_desc) 281 return -ENODEV; 282 if (roland_desc[0] < 6 || roland_desc[3] != 2) 283 continue; 284 return create_any_midi_quirk(chip, iface, driver, 285 &roland_midi_quirk); 286 } 287 } 288 289 static int create_std_midi_quirk(struct snd_usb_audio *chip, 290 struct usb_interface *iface, 291 struct usb_driver *driver, 292 struct usb_host_interface *alts) 293 { 294 struct usb_ms_header_descriptor *mshd; 295 struct usb_ms_endpoint_descriptor *msepd; 296 297 /* must have the MIDIStreaming interface header descriptor*/ 298 mshd = (struct usb_ms_header_descriptor *)alts->extra; 299 if (alts->extralen < 7 || 300 mshd->bLength < 7 || 301 mshd->bDescriptorType != USB_DT_CS_INTERFACE || 302 mshd->bDescriptorSubtype != USB_MS_HEADER) 303 return -ENODEV; 304 /* must have the MIDIStreaming endpoint descriptor*/ 305 msepd = (struct usb_ms_endpoint_descriptor *)alts->endpoint[0].extra; 306 if (alts->endpoint[0].extralen < 4 || 307 msepd->bLength < 4 || 308 msepd->bDescriptorType != USB_DT_CS_ENDPOINT || 309 msepd->bDescriptorSubtype != UAC_MS_GENERAL || 310 msepd->bNumEmbMIDIJack < 1 || 311 msepd->bNumEmbMIDIJack > 16) 312 return -ENODEV; 313 314 return create_any_midi_quirk(chip, iface, driver, NULL); 315 } 316 317 static int create_auto_midi_quirk(struct snd_usb_audio *chip, 318 struct usb_interface *iface, 319 struct usb_driver *driver) 320 { 321 struct usb_host_interface *alts; 322 struct usb_interface_descriptor *altsd; 323 struct usb_endpoint_descriptor *epd; 324 int err; 325 326 alts = &iface->altsetting[0]; 327 altsd = get_iface_desc(alts); 328 329 /* must have at least one bulk/interrupt endpoint for streaming */ 330 if (altsd->bNumEndpoints < 1) 331 return -ENODEV; 332 epd = get_endpoint(alts, 0); 333 if (!usb_endpoint_xfer_bulk(epd) && 334 !usb_endpoint_xfer_int(epd)) 335 return -ENODEV; 336 337 switch (USB_ID_VENDOR(chip->usb_id)) { 338 case 0x0499: /* Yamaha */ 339 err = create_yamaha_midi_quirk(chip, iface, driver, alts); 340 if (err != -ENODEV) 341 return err; 342 break; 343 case 0x0582: /* Roland */ 344 err = create_roland_midi_quirk(chip, iface, driver, alts); 345 if (err != -ENODEV) 346 return err; 347 break; 348 } 349 350 return create_std_midi_quirk(chip, iface, driver, alts); 351 } 352 353 static int create_autodetect_quirk(struct snd_usb_audio *chip, 354 struct usb_interface *iface, 355 struct usb_driver *driver) 356 { 357 int err; 358 359 err = create_auto_pcm_quirk(chip, iface, driver); 360 if (err == -ENODEV) 361 err = create_auto_midi_quirk(chip, iface, driver); 362 return err; 363 } 364 365 static int create_autodetect_quirks(struct snd_usb_audio *chip, 366 struct usb_interface *iface, 367 struct usb_driver *driver, 368 const struct snd_usb_audio_quirk *quirk) 369 { 370 int probed_ifnum = get_iface_desc(iface->altsetting)->bInterfaceNumber; 371 int ifcount, ifnum, err; 372 373 err = create_autodetect_quirk(chip, iface, driver); 374 if (err < 0) 375 return err; 376 377 /* 378 * ALSA PCM playback/capture devices cannot be registered in two steps, 379 * so we have to claim the other corresponding interface here. 380 */ 381 ifcount = chip->dev->actconfig->desc.bNumInterfaces; 382 for (ifnum = 0; ifnum < ifcount; ifnum++) { 383 if (ifnum == probed_ifnum || quirk->ifnum >= 0) 384 continue; 385 iface = usb_ifnum_to_if(chip->dev, ifnum); 386 if (!iface || 387 usb_interface_claimed(iface) || 388 get_iface_desc(iface->altsetting)->bInterfaceClass != 389 USB_CLASS_VENDOR_SPEC) 390 continue; 391 392 err = create_autodetect_quirk(chip, iface, driver); 393 if (err >= 0) 394 usb_driver_claim_interface(driver, iface, (void *)-1L); 395 } 396 397 return 0; 398 } 399 400 /* 401 * Create a stream for an Edirol UA-700/UA-25/UA-4FX interface. 402 * The only way to detect the sample rate is by looking at wMaxPacketSize. 403 */ 404 static int create_uaxx_quirk(struct snd_usb_audio *chip, 405 struct usb_interface *iface, 406 struct usb_driver *driver, 407 const struct snd_usb_audio_quirk *quirk) 408 { 409 static const struct audioformat ua_format = { 410 .formats = SNDRV_PCM_FMTBIT_S24_3LE, 411 .channels = 2, 412 .fmt_type = UAC_FORMAT_TYPE_I, 413 .altsetting = 1, 414 .altset_idx = 1, 415 .rates = SNDRV_PCM_RATE_CONTINUOUS, 416 }; 417 struct usb_host_interface *alts; 418 struct usb_interface_descriptor *altsd; 419 struct audioformat *fp; 420 int stream, err; 421 422 /* both PCM and MIDI interfaces have 2 or more altsettings */ 423 if (iface->num_altsetting < 2) 424 return -ENXIO; 425 alts = &iface->altsetting[1]; 426 altsd = get_iface_desc(alts); 427 428 if (altsd->bNumEndpoints == 2) { 429 static const struct snd_usb_midi_endpoint_info ua700_ep = { 430 .out_cables = 0x0003, 431 .in_cables = 0x0003 432 }; 433 static const struct snd_usb_audio_quirk ua700_quirk = { 434 .type = QUIRK_MIDI_FIXED_ENDPOINT, 435 .data = &ua700_ep 436 }; 437 static const struct snd_usb_midi_endpoint_info uaxx_ep = { 438 .out_cables = 0x0001, 439 .in_cables = 0x0001 440 }; 441 static const struct snd_usb_audio_quirk uaxx_quirk = { 442 .type = QUIRK_MIDI_FIXED_ENDPOINT, 443 .data = &uaxx_ep 444 }; 445 const struct snd_usb_audio_quirk *quirk = 446 chip->usb_id == USB_ID(0x0582, 0x002b) 447 ? &ua700_quirk : &uaxx_quirk; 448 return __snd_usbmidi_create(chip->card, iface, 449 &chip->midi_list, quirk, 450 chip->usb_id); 451 } 452 453 if (altsd->bNumEndpoints != 1) 454 return -ENXIO; 455 456 fp = kmemdup(&ua_format, sizeof(*fp), GFP_KERNEL); 457 if (!fp) 458 return -ENOMEM; 459 460 fp->iface = altsd->bInterfaceNumber; 461 fp->endpoint = get_endpoint(alts, 0)->bEndpointAddress; 462 fp->ep_attr = get_endpoint(alts, 0)->bmAttributes; 463 fp->datainterval = 0; 464 fp->maxpacksize = le16_to_cpu(get_endpoint(alts, 0)->wMaxPacketSize); 465 INIT_LIST_HEAD(&fp->list); 466 467 switch (fp->maxpacksize) { 468 case 0x120: 469 fp->rate_max = fp->rate_min = 44100; 470 break; 471 case 0x138: 472 case 0x140: 473 fp->rate_max = fp->rate_min = 48000; 474 break; 475 case 0x258: 476 case 0x260: 477 fp->rate_max = fp->rate_min = 96000; 478 break; 479 default: 480 usb_audio_err(chip, "unknown sample rate\n"); 481 kfree(fp); 482 return -ENXIO; 483 } 484 485 stream = (fp->endpoint & USB_DIR_IN) 486 ? SNDRV_PCM_STREAM_CAPTURE : SNDRV_PCM_STREAM_PLAYBACK; 487 err = snd_usb_add_audio_stream(chip, stream, fp); 488 if (err < 0) { 489 list_del(&fp->list); /* unlink for avoiding double-free */ 490 kfree(fp); 491 return err; 492 } 493 usb_set_interface(chip->dev, fp->iface, 0); 494 return 0; 495 } 496 497 /* 498 * Create a standard mixer for the specified interface. 499 */ 500 static int create_standard_mixer_quirk(struct snd_usb_audio *chip, 501 struct usb_interface *iface, 502 struct usb_driver *driver, 503 const struct snd_usb_audio_quirk *quirk) 504 { 505 if (quirk->ifnum < 0) 506 return 0; 507 508 return snd_usb_create_mixer(chip, quirk->ifnum, 0); 509 } 510 511 static int setup_disable_autosuspend(struct snd_usb_audio *chip, 512 struct usb_interface *iface, 513 struct usb_driver *driver, 514 const struct snd_usb_audio_quirk *quirk) 515 { 516 driver->supports_autosuspend = 0; 517 return 1; /* Continue with creating streams and mixer */ 518 } 519 520 /* 521 * audio-interface quirks 522 * 523 * returns zero if no standard audio/MIDI parsing is needed. 524 * returns a positive value if standard audio/midi interfaces are parsed 525 * after this. 526 * returns a negative value at error. 527 */ 528 int snd_usb_create_quirk(struct snd_usb_audio *chip, 529 struct usb_interface *iface, 530 struct usb_driver *driver, 531 const struct snd_usb_audio_quirk *quirk) 532 { 533 typedef int (*quirk_func_t)(struct snd_usb_audio *, 534 struct usb_interface *, 535 struct usb_driver *, 536 const struct snd_usb_audio_quirk *); 537 static const quirk_func_t quirk_funcs[] = { 538 [QUIRK_IGNORE_INTERFACE] = ignore_interface_quirk, 539 [QUIRK_COMPOSITE] = create_composite_quirk, 540 [QUIRK_AUTODETECT] = create_autodetect_quirks, 541 [QUIRK_MIDI_STANDARD_INTERFACE] = create_any_midi_quirk, 542 [QUIRK_MIDI_FIXED_ENDPOINT] = create_any_midi_quirk, 543 [QUIRK_MIDI_YAMAHA] = create_any_midi_quirk, 544 [QUIRK_MIDI_ROLAND] = create_any_midi_quirk, 545 [QUIRK_MIDI_MIDIMAN] = create_any_midi_quirk, 546 [QUIRK_MIDI_NOVATION] = create_any_midi_quirk, 547 [QUIRK_MIDI_RAW_BYTES] = create_any_midi_quirk, 548 [QUIRK_MIDI_EMAGIC] = create_any_midi_quirk, 549 [QUIRK_MIDI_CME] = create_any_midi_quirk, 550 [QUIRK_MIDI_AKAI] = create_any_midi_quirk, 551 [QUIRK_MIDI_FTDI] = create_any_midi_quirk, 552 [QUIRK_MIDI_CH345] = create_any_midi_quirk, 553 [QUIRK_AUDIO_STANDARD_INTERFACE] = create_standard_audio_quirk, 554 [QUIRK_AUDIO_FIXED_ENDPOINT] = create_fixed_stream_quirk, 555 [QUIRK_AUDIO_EDIROL_UAXX] = create_uaxx_quirk, 556 [QUIRK_AUDIO_ALIGN_TRANSFER] = create_align_transfer_quirk, 557 [QUIRK_AUDIO_STANDARD_MIXER] = create_standard_mixer_quirk, 558 [QUIRK_SETUP_DISABLE_AUTOSUSPEND] = setup_disable_autosuspend, 559 }; 560 561 if (quirk->type < QUIRK_TYPE_COUNT) { 562 return quirk_funcs[quirk->type](chip, iface, driver, quirk); 563 } else { 564 usb_audio_err(chip, "invalid quirk type %d\n", quirk->type); 565 return -ENXIO; 566 } 567 } 568 569 /* 570 * boot quirks 571 */ 572 573 #define EXTIGY_FIRMWARE_SIZE_OLD 794 574 #define EXTIGY_FIRMWARE_SIZE_NEW 483 575 576 static int snd_usb_extigy_boot_quirk(struct usb_device *dev, struct usb_interface *intf) 577 { 578 struct usb_host_config *config = dev->actconfig; 579 int err; 580 581 if (le16_to_cpu(get_cfg_desc(config)->wTotalLength) == EXTIGY_FIRMWARE_SIZE_OLD || 582 le16_to_cpu(get_cfg_desc(config)->wTotalLength) == EXTIGY_FIRMWARE_SIZE_NEW) { 583 dev_dbg(&dev->dev, "sending Extigy boot sequence...\n"); 584 /* Send message to force it to reconnect with full interface. */ 585 err = snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev,0), 586 0x10, 0x43, 0x0001, 0x000a, NULL, 0); 587 if (err < 0) 588 dev_dbg(&dev->dev, "error sending boot message: %d\n", err); 589 err = usb_get_descriptor(dev, USB_DT_DEVICE, 0, 590 &dev->descriptor, sizeof(dev->descriptor)); 591 config = dev->actconfig; 592 if (err < 0) 593 dev_dbg(&dev->dev, "error usb_get_descriptor: %d\n", err); 594 err = usb_reset_configuration(dev); 595 if (err < 0) 596 dev_dbg(&dev->dev, "error usb_reset_configuration: %d\n", err); 597 dev_dbg(&dev->dev, "extigy_boot: new boot length = %d\n", 598 le16_to_cpu(get_cfg_desc(config)->wTotalLength)); 599 return -ENODEV; /* quit this anyway */ 600 } 601 return 0; 602 } 603 604 static int snd_usb_audigy2nx_boot_quirk(struct usb_device *dev) 605 { 606 u8 buf = 1; 607 608 snd_usb_ctl_msg(dev, usb_rcvctrlpipe(dev, 0), 0x2a, 609 USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_OTHER, 610 0, 0, &buf, 1); 611 if (buf == 0) { 612 snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), 0x29, 613 USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_OTHER, 614 1, 2000, NULL, 0); 615 return -ENODEV; 616 } 617 return 0; 618 } 619 620 static int snd_usb_fasttrackpro_boot_quirk(struct usb_device *dev) 621 { 622 int err; 623 624 if (dev->actconfig->desc.bConfigurationValue == 1) { 625 dev_info(&dev->dev, 626 "Fast Track Pro switching to config #2\n"); 627 /* This function has to be available by the usb core module. 628 * if it is not avialable the boot quirk has to be left out 629 * and the configuration has to be set by udev or hotplug 630 * rules 631 */ 632 err = usb_driver_set_configuration(dev, 2); 633 if (err < 0) 634 dev_dbg(&dev->dev, 635 "error usb_driver_set_configuration: %d\n", 636 err); 637 /* Always return an error, so that we stop creating a device 638 that will just be destroyed and recreated with a new 639 configuration */ 640 return -ENODEV; 641 } else 642 dev_info(&dev->dev, "Fast Track Pro config OK\n"); 643 644 return 0; 645 } 646 647 /* 648 * C-Media CM106/CM106+ have four 16-bit internal registers that are nicely 649 * documented in the device's data sheet. 650 */ 651 static int snd_usb_cm106_write_int_reg(struct usb_device *dev, int reg, u16 value) 652 { 653 u8 buf[4]; 654 buf[0] = 0x20; 655 buf[1] = value & 0xff; 656 buf[2] = (value >> 8) & 0xff; 657 buf[3] = reg; 658 return snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), USB_REQ_SET_CONFIGURATION, 659 USB_DIR_OUT | USB_TYPE_CLASS | USB_RECIP_ENDPOINT, 660 0, 0, &buf, 4); 661 } 662 663 static int snd_usb_cm106_boot_quirk(struct usb_device *dev) 664 { 665 /* 666 * Enable line-out driver mode, set headphone source to front 667 * channels, enable stereo mic. 668 */ 669 return snd_usb_cm106_write_int_reg(dev, 2, 0x8004); 670 } 671 672 /* 673 * CM6206 registers from the CM6206 datasheet rev 2.1 674 */ 675 #define CM6206_REG0_DMA_MASTER BIT(15) 676 #define CM6206_REG0_SPDIFO_RATE_48K (2 << 12) 677 #define CM6206_REG0_SPDIFO_RATE_96K (7 << 12) 678 /* Bit 4 thru 11 is the S/PDIF category code */ 679 #define CM6206_REG0_SPDIFO_CAT_CODE_GENERAL (0 << 4) 680 #define CM6206_REG0_SPDIFO_EMPHASIS_CD BIT(3) 681 #define CM6206_REG0_SPDIFO_COPYRIGHT_NA BIT(2) 682 #define CM6206_REG0_SPDIFO_NON_AUDIO BIT(1) 683 #define CM6206_REG0_SPDIFO_PRO_FORMAT BIT(0) 684 685 #define CM6206_REG1_TEST_SEL_CLK BIT(14) 686 #define CM6206_REG1_PLLBIN_EN BIT(13) 687 #define CM6206_REG1_SOFT_MUTE_EN BIT(12) 688 #define CM6206_REG1_GPIO4_OUT BIT(11) 689 #define CM6206_REG1_GPIO4_OE BIT(10) 690 #define CM6206_REG1_GPIO3_OUT BIT(9) 691 #define CM6206_REG1_GPIO3_OE BIT(8) 692 #define CM6206_REG1_GPIO2_OUT BIT(7) 693 #define CM6206_REG1_GPIO2_OE BIT(6) 694 #define CM6206_REG1_GPIO1_OUT BIT(5) 695 #define CM6206_REG1_GPIO1_OE BIT(4) 696 #define CM6206_REG1_SPDIFO_INVALID BIT(3) 697 #define CM6206_REG1_SPDIF_LOOP_EN BIT(2) 698 #define CM6206_REG1_SPDIFO_DIS BIT(1) 699 #define CM6206_REG1_SPDIFI_MIX BIT(0) 700 701 #define CM6206_REG2_DRIVER_ON BIT(15) 702 #define CM6206_REG2_HEADP_SEL_SIDE_CHANNELS (0 << 13) 703 #define CM6206_REG2_HEADP_SEL_SURROUND_CHANNELS (1 << 13) 704 #define CM6206_REG2_HEADP_SEL_CENTER_SUBW (2 << 13) 705 #define CM6206_REG2_HEADP_SEL_FRONT_CHANNELS (3 << 13) 706 #define CM6206_REG2_MUTE_HEADPHONE_RIGHT BIT(12) 707 #define CM6206_REG2_MUTE_HEADPHONE_LEFT BIT(11) 708 #define CM6206_REG2_MUTE_REAR_SURROUND_RIGHT BIT(10) 709 #define CM6206_REG2_MUTE_REAR_SURROUND_LEFT BIT(9) 710 #define CM6206_REG2_MUTE_SIDE_SURROUND_RIGHT BIT(8) 711 #define CM6206_REG2_MUTE_SIDE_SURROUND_LEFT BIT(7) 712 #define CM6206_REG2_MUTE_SUBWOOFER BIT(6) 713 #define CM6206_REG2_MUTE_CENTER BIT(5) 714 #define CM6206_REG2_MUTE_RIGHT_FRONT BIT(3) 715 #define CM6206_REG2_MUTE_LEFT_FRONT BIT(3) 716 #define CM6206_REG2_EN_BTL BIT(2) 717 #define CM6206_REG2_MCUCLKSEL_1_5_MHZ (0) 718 #define CM6206_REG2_MCUCLKSEL_3_MHZ (1) 719 #define CM6206_REG2_MCUCLKSEL_6_MHZ (2) 720 #define CM6206_REG2_MCUCLKSEL_12_MHZ (3) 721 722 /* Bit 11..13 sets the sensitivity to FLY tuner volume control VP/VD signal */ 723 #define CM6206_REG3_FLYSPEED_DEFAULT (2 << 11) 724 #define CM6206_REG3_VRAP25EN BIT(10) 725 #define CM6206_REG3_MSEL1 BIT(9) 726 #define CM6206_REG3_SPDIFI_RATE_44_1K BIT(0 << 7) 727 #define CM6206_REG3_SPDIFI_RATE_48K BIT(2 << 7) 728 #define CM6206_REG3_SPDIFI_RATE_32K BIT(3 << 7) 729 #define CM6206_REG3_PINSEL BIT(6) 730 #define CM6206_REG3_FOE BIT(5) 731 #define CM6206_REG3_ROE BIT(4) 732 #define CM6206_REG3_CBOE BIT(3) 733 #define CM6206_REG3_LOSE BIT(2) 734 #define CM6206_REG3_HPOE BIT(1) 735 #define CM6206_REG3_SPDIFI_CANREC BIT(0) 736 737 #define CM6206_REG5_DA_RSTN BIT(13) 738 #define CM6206_REG5_AD_RSTN BIT(12) 739 #define CM6206_REG5_SPDIFO_AD2SPDO BIT(12) 740 #define CM6206_REG5_SPDIFO_SEL_FRONT (0 << 9) 741 #define CM6206_REG5_SPDIFO_SEL_SIDE_SUR (1 << 9) 742 #define CM6206_REG5_SPDIFO_SEL_CEN_LFE (2 << 9) 743 #define CM6206_REG5_SPDIFO_SEL_REAR_SUR (3 << 9) 744 #define CM6206_REG5_CODECM BIT(8) 745 #define CM6206_REG5_EN_HPF BIT(7) 746 #define CM6206_REG5_T_SEL_DSDA4 BIT(6) 747 #define CM6206_REG5_T_SEL_DSDA3 BIT(5) 748 #define CM6206_REG5_T_SEL_DSDA2 BIT(4) 749 #define CM6206_REG5_T_SEL_DSDA1 BIT(3) 750 #define CM6206_REG5_T_SEL_DSDAD_NORMAL 0 751 #define CM6206_REG5_T_SEL_DSDAD_FRONT 4 752 #define CM6206_REG5_T_SEL_DSDAD_S_SURROUND 5 753 #define CM6206_REG5_T_SEL_DSDAD_CEN_LFE 6 754 #define CM6206_REG5_T_SEL_DSDAD_R_SURROUND 7 755 756 static int snd_usb_cm6206_boot_quirk(struct usb_device *dev) 757 { 758 int err = 0, reg; 759 int val[] = { 760 /* 761 * Values here are chosen based on sniffing USB traffic 762 * under Windows. 763 * 764 * REG0: DAC is master, sample rate 48kHz, no copyright 765 */ 766 CM6206_REG0_SPDIFO_RATE_48K | 767 CM6206_REG0_SPDIFO_COPYRIGHT_NA, 768 /* 769 * REG1: PLL binary search enable, soft mute enable. 770 */ 771 CM6206_REG1_PLLBIN_EN | 772 CM6206_REG1_SOFT_MUTE_EN, 773 /* 774 * REG2: enable output drivers, 775 * select front channels to the headphone output, 776 * then mute the headphone channels, run the MCU 777 * at 1.5 MHz. 778 */ 779 CM6206_REG2_DRIVER_ON | 780 CM6206_REG2_HEADP_SEL_FRONT_CHANNELS | 781 CM6206_REG2_MUTE_HEADPHONE_RIGHT | 782 CM6206_REG2_MUTE_HEADPHONE_LEFT, 783 /* 784 * REG3: default flyspeed, set 2.5V mic bias 785 * enable all line out ports and enable SPDIF 786 */ 787 CM6206_REG3_FLYSPEED_DEFAULT | 788 CM6206_REG3_VRAP25EN | 789 CM6206_REG3_FOE | 790 CM6206_REG3_ROE | 791 CM6206_REG3_CBOE | 792 CM6206_REG3_LOSE | 793 CM6206_REG3_HPOE | 794 CM6206_REG3_SPDIFI_CANREC, 795 /* REG4 is just a bunch of GPIO lines */ 796 0x0000, 797 /* REG5: de-assert AD/DA reset signals */ 798 CM6206_REG5_DA_RSTN | 799 CM6206_REG5_AD_RSTN }; 800 801 for (reg = 0; reg < ARRAY_SIZE(val); reg++) { 802 err = snd_usb_cm106_write_int_reg(dev, reg, val[reg]); 803 if (err < 0) 804 return err; 805 } 806 807 return err; 808 } 809 810 /* quirk for Plantronics GameCom 780 with CM6302 chip */ 811 static int snd_usb_gamecon780_boot_quirk(struct usb_device *dev) 812 { 813 /* set the initial volume and don't change; other values are either 814 * too loud or silent due to firmware bug (bko#65251) 815 */ 816 u8 buf[2] = { 0x74, 0xe3 }; 817 return snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), UAC_SET_CUR, 818 USB_RECIP_INTERFACE | USB_TYPE_CLASS | USB_DIR_OUT, 819 UAC_FU_VOLUME << 8, 9 << 8, buf, 2); 820 } 821 822 /* 823 * Novation Twitch DJ controller 824 * Focusrite Novation Saffire 6 USB audio card 825 */ 826 static int snd_usb_novation_boot_quirk(struct usb_device *dev) 827 { 828 /* preemptively set up the device because otherwise the 829 * raw MIDI endpoints are not active */ 830 usb_set_interface(dev, 0, 1); 831 return 0; 832 } 833 834 /* 835 * This call will put the synth in "USB send" mode, i.e it will send MIDI 836 * messages through USB (this is disabled at startup). The synth will 837 * acknowledge by sending a sysex on endpoint 0x85 and by displaying a USB 838 * sign on its LCD. Values here are chosen based on sniffing USB traffic 839 * under Windows. 840 */ 841 static int snd_usb_accessmusic_boot_quirk(struct usb_device *dev) 842 { 843 int err, actual_length; 844 /* "midi send" enable */ 845 static const u8 seq[] = { 0x4e, 0x73, 0x52, 0x01 }; 846 void *buf; 847 848 if (usb_pipe_type_check(dev, usb_sndintpipe(dev, 0x05))) 849 return -EINVAL; 850 buf = kmemdup(seq, ARRAY_SIZE(seq), GFP_KERNEL); 851 if (!buf) 852 return -ENOMEM; 853 err = usb_interrupt_msg(dev, usb_sndintpipe(dev, 0x05), buf, 854 ARRAY_SIZE(seq), &actual_length, 1000); 855 kfree(buf); 856 if (err < 0) 857 return err; 858 859 return 0; 860 } 861 862 /* 863 * Some sound cards from Native Instruments are in fact compliant to the USB 864 * audio standard of version 2 and other approved USB standards, even though 865 * they come up as vendor-specific device when first connected. 866 * 867 * However, they can be told to come up with a new set of descriptors 868 * upon their next enumeration, and the interfaces announced by the new 869 * descriptors will then be handled by the kernel's class drivers. As the 870 * product ID will also change, no further checks are required. 871 */ 872 873 static int snd_usb_nativeinstruments_boot_quirk(struct usb_device *dev) 874 { 875 int ret; 876 877 ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 878 0xaf, USB_TYPE_VENDOR | USB_RECIP_DEVICE, 879 1, 0, NULL, 0, 1000); 880 881 if (ret < 0) 882 return ret; 883 884 usb_reset_device(dev); 885 886 /* return -EAGAIN, so the creation of an audio interface for this 887 * temporary device is aborted. The device will reconnect with a 888 * new product ID */ 889 return -EAGAIN; 890 } 891 892 static void mbox2_setup_48_24_magic(struct usb_device *dev) 893 { 894 u8 srate[3]; 895 u8 temp[12]; 896 897 /* Choose 48000Hz permanently */ 898 srate[0] = 0x80; 899 srate[1] = 0xbb; 900 srate[2] = 0x00; 901 902 /* Send the magic! */ 903 snd_usb_ctl_msg(dev, usb_rcvctrlpipe(dev, 0), 904 0x01, 0x22, 0x0100, 0x0085, &temp, 0x0003); 905 snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), 906 0x81, 0xa2, 0x0100, 0x0085, &srate, 0x0003); 907 snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), 908 0x81, 0xa2, 0x0100, 0x0086, &srate, 0x0003); 909 snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), 910 0x81, 0xa2, 0x0100, 0x0003, &srate, 0x0003); 911 return; 912 } 913 914 /* Digidesign Mbox 2 needs to load firmware onboard 915 * and driver must wait a few seconds for initialisation. 916 */ 917 918 #define MBOX2_FIRMWARE_SIZE 646 919 #define MBOX2_BOOT_LOADING 0x01 /* Hard coded into the device */ 920 #define MBOX2_BOOT_READY 0x02 /* Hard coded into the device */ 921 922 static int snd_usb_mbox2_boot_quirk(struct usb_device *dev) 923 { 924 struct usb_host_config *config = dev->actconfig; 925 int err; 926 u8 bootresponse[0x12]; 927 int fwsize; 928 int count; 929 930 fwsize = le16_to_cpu(get_cfg_desc(config)->wTotalLength); 931 932 if (fwsize != MBOX2_FIRMWARE_SIZE) { 933 dev_err(&dev->dev, "Invalid firmware size=%d.\n", fwsize); 934 return -ENODEV; 935 } 936 937 dev_dbg(&dev->dev, "Sending Digidesign Mbox 2 boot sequence...\n"); 938 939 count = 0; 940 bootresponse[0] = MBOX2_BOOT_LOADING; 941 while ((bootresponse[0] == MBOX2_BOOT_LOADING) && (count < 10)) { 942 msleep(500); /* 0.5 second delay */ 943 snd_usb_ctl_msg(dev, usb_rcvctrlpipe(dev, 0), 944 /* Control magic - load onboard firmware */ 945 0x85, 0xc0, 0x0001, 0x0000, &bootresponse, 0x0012); 946 if (bootresponse[0] == MBOX2_BOOT_READY) 947 break; 948 dev_dbg(&dev->dev, "device not ready, resending boot sequence...\n"); 949 count++; 950 } 951 952 if (bootresponse[0] != MBOX2_BOOT_READY) { 953 dev_err(&dev->dev, "Unknown bootresponse=%d, or timed out, ignoring device.\n", bootresponse[0]); 954 return -ENODEV; 955 } 956 957 dev_dbg(&dev->dev, "device initialised!\n"); 958 959 err = usb_get_descriptor(dev, USB_DT_DEVICE, 0, 960 &dev->descriptor, sizeof(dev->descriptor)); 961 config = dev->actconfig; 962 if (err < 0) 963 dev_dbg(&dev->dev, "error usb_get_descriptor: %d\n", err); 964 965 err = usb_reset_configuration(dev); 966 if (err < 0) 967 dev_dbg(&dev->dev, "error usb_reset_configuration: %d\n", err); 968 dev_dbg(&dev->dev, "mbox2_boot: new boot length = %d\n", 969 le16_to_cpu(get_cfg_desc(config)->wTotalLength)); 970 971 mbox2_setup_48_24_magic(dev); 972 973 dev_info(&dev->dev, "Digidesign Mbox 2: 24bit 48kHz"); 974 975 return 0; /* Successful boot */ 976 } 977 978 static int snd_usb_axefx3_boot_quirk(struct usb_device *dev) 979 { 980 int err; 981 982 dev_dbg(&dev->dev, "Waiting for Axe-Fx III to boot up...\n"); 983 984 /* If the Axe-Fx III has not fully booted, it will timeout when trying 985 * to enable the audio streaming interface. A more generous timeout is 986 * used here to detect when the Axe-Fx III has finished booting as the 987 * set interface message will be acked once it has 988 */ 989 err = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 990 USB_REQ_SET_INTERFACE, USB_RECIP_INTERFACE, 991 1, 1, NULL, 0, 120000); 992 if (err < 0) { 993 dev_err(&dev->dev, 994 "failed waiting for Axe-Fx III to boot: %d\n", err); 995 return err; 996 } 997 998 dev_dbg(&dev->dev, "Axe-Fx III is now ready\n"); 999 1000 err = usb_set_interface(dev, 1, 0); 1001 if (err < 0) 1002 dev_dbg(&dev->dev, 1003 "error stopping Axe-Fx III interface: %d\n", err); 1004 1005 return 0; 1006 } 1007 1008 1009 #define MICROBOOK_BUF_SIZE 128 1010 1011 static int snd_usb_motu_microbookii_communicate(struct usb_device *dev, u8 *buf, 1012 int buf_size, int *length) 1013 { 1014 int err, actual_length; 1015 1016 if (usb_pipe_type_check(dev, usb_sndintpipe(dev, 0x01))) 1017 return -EINVAL; 1018 err = usb_interrupt_msg(dev, usb_sndintpipe(dev, 0x01), buf, *length, 1019 &actual_length, 1000); 1020 if (err < 0) 1021 return err; 1022 1023 print_hex_dump(KERN_DEBUG, "MicroBookII snd: ", DUMP_PREFIX_NONE, 16, 1, 1024 buf, actual_length, false); 1025 1026 memset(buf, 0, buf_size); 1027 1028 if (usb_pipe_type_check(dev, usb_rcvintpipe(dev, 0x82))) 1029 return -EINVAL; 1030 err = usb_interrupt_msg(dev, usb_rcvintpipe(dev, 0x82), buf, buf_size, 1031 &actual_length, 1000); 1032 if (err < 0) 1033 return err; 1034 1035 print_hex_dump(KERN_DEBUG, "MicroBookII rcv: ", DUMP_PREFIX_NONE, 16, 1, 1036 buf, actual_length, false); 1037 1038 *length = actual_length; 1039 return 0; 1040 } 1041 1042 static int snd_usb_motu_microbookii_boot_quirk(struct usb_device *dev) 1043 { 1044 int err, actual_length, poll_attempts = 0; 1045 static const u8 set_samplerate_seq[] = { 0x00, 0x00, 0x00, 0x00, 1046 0x00, 0x00, 0x0b, 0x14, 1047 0x00, 0x00, 0x00, 0x01 }; 1048 static const u8 poll_ready_seq[] = { 0x00, 0x04, 0x00, 0x00, 1049 0x00, 0x00, 0x0b, 0x18 }; 1050 u8 *buf = kzalloc(MICROBOOK_BUF_SIZE, GFP_KERNEL); 1051 1052 if (!buf) 1053 return -ENOMEM; 1054 1055 dev_info(&dev->dev, "Waiting for MOTU Microbook II to boot up...\n"); 1056 1057 /* First we tell the device which sample rate to use. */ 1058 memcpy(buf, set_samplerate_seq, sizeof(set_samplerate_seq)); 1059 actual_length = sizeof(set_samplerate_seq); 1060 err = snd_usb_motu_microbookii_communicate(dev, buf, MICROBOOK_BUF_SIZE, 1061 &actual_length); 1062 1063 if (err < 0) { 1064 dev_err(&dev->dev, 1065 "failed setting the sample rate for Motu MicroBook II: %d\n", 1066 err); 1067 goto free_buf; 1068 } 1069 1070 /* Then we poll every 100 ms until the device informs of its readiness. */ 1071 while (true) { 1072 if (++poll_attempts > 100) { 1073 dev_err(&dev->dev, 1074 "failed booting Motu MicroBook II: timeout\n"); 1075 err = -ENODEV; 1076 goto free_buf; 1077 } 1078 1079 memset(buf, 0, MICROBOOK_BUF_SIZE); 1080 memcpy(buf, poll_ready_seq, sizeof(poll_ready_seq)); 1081 1082 actual_length = sizeof(poll_ready_seq); 1083 err = snd_usb_motu_microbookii_communicate( 1084 dev, buf, MICROBOOK_BUF_SIZE, &actual_length); 1085 if (err < 0) { 1086 dev_err(&dev->dev, 1087 "failed booting Motu MicroBook II: communication error %d\n", 1088 err); 1089 goto free_buf; 1090 } 1091 1092 /* the device signals its readiness through a message of the 1093 * form 1094 * XX 06 00 00 00 00 0b 18 00 00 00 01 1095 * If the device is not yet ready to accept audio data, the 1096 * last byte of that sequence is 00. 1097 */ 1098 if (actual_length == 12 && buf[actual_length - 1] == 1) 1099 break; 1100 1101 msleep(100); 1102 } 1103 1104 dev_info(&dev->dev, "MOTU MicroBook II ready\n"); 1105 1106 free_buf: 1107 kfree(buf); 1108 return err; 1109 } 1110 1111 static int snd_usb_motu_m_series_boot_quirk(struct usb_device *dev) 1112 { 1113 msleep(2000); 1114 1115 return 0; 1116 } 1117 1118 /* 1119 * Setup quirks 1120 */ 1121 #define MAUDIO_SET 0x01 /* parse device_setup */ 1122 #define MAUDIO_SET_COMPATIBLE 0x80 /* use only "win-compatible" interfaces */ 1123 #define MAUDIO_SET_DTS 0x02 /* enable DTS Digital Output */ 1124 #define MAUDIO_SET_96K 0x04 /* 48-96kHz rate if set, 8-48kHz otherwise */ 1125 #define MAUDIO_SET_24B 0x08 /* 24bits sample if set, 16bits otherwise */ 1126 #define MAUDIO_SET_DI 0x10 /* enable Digital Input */ 1127 #define MAUDIO_SET_MASK 0x1f /* bit mask for setup value */ 1128 #define MAUDIO_SET_24B_48K_DI 0x19 /* 24bits+48kHz+Digital Input */ 1129 #define MAUDIO_SET_24B_48K_NOTDI 0x09 /* 24bits+48kHz+No Digital Input */ 1130 #define MAUDIO_SET_16B_48K_DI 0x11 /* 16bits+48kHz+Digital Input */ 1131 #define MAUDIO_SET_16B_48K_NOTDI 0x01 /* 16bits+48kHz+No Digital Input */ 1132 1133 static int quattro_skip_setting_quirk(struct snd_usb_audio *chip, 1134 int iface, int altno) 1135 { 1136 /* Reset ALL ifaces to 0 altsetting. 1137 * Call it for every possible altsetting of every interface. 1138 */ 1139 usb_set_interface(chip->dev, iface, 0); 1140 if (chip->setup & MAUDIO_SET) { 1141 if (chip->setup & MAUDIO_SET_COMPATIBLE) { 1142 if (iface != 1 && iface != 2) 1143 return 1; /* skip all interfaces but 1 and 2 */ 1144 } else { 1145 unsigned int mask; 1146 if (iface == 1 || iface == 2) 1147 return 1; /* skip interfaces 1 and 2 */ 1148 if ((chip->setup & MAUDIO_SET_96K) && altno != 1) 1149 return 1; /* skip this altsetting */ 1150 mask = chip->setup & MAUDIO_SET_MASK; 1151 if (mask == MAUDIO_SET_24B_48K_DI && altno != 2) 1152 return 1; /* skip this altsetting */ 1153 if (mask == MAUDIO_SET_24B_48K_NOTDI && altno != 3) 1154 return 1; /* skip this altsetting */ 1155 if (mask == MAUDIO_SET_16B_48K_NOTDI && altno != 4) 1156 return 1; /* skip this altsetting */ 1157 } 1158 } 1159 usb_audio_dbg(chip, 1160 "using altsetting %d for interface %d config %d\n", 1161 altno, iface, chip->setup); 1162 return 0; /* keep this altsetting */ 1163 } 1164 1165 static int audiophile_skip_setting_quirk(struct snd_usb_audio *chip, 1166 int iface, 1167 int altno) 1168 { 1169 /* Reset ALL ifaces to 0 altsetting. 1170 * Call it for every possible altsetting of every interface. 1171 */ 1172 usb_set_interface(chip->dev, iface, 0); 1173 1174 if (chip->setup & MAUDIO_SET) { 1175 unsigned int mask; 1176 if ((chip->setup & MAUDIO_SET_DTS) && altno != 6) 1177 return 1; /* skip this altsetting */ 1178 if ((chip->setup & MAUDIO_SET_96K) && altno != 1) 1179 return 1; /* skip this altsetting */ 1180 mask = chip->setup & MAUDIO_SET_MASK; 1181 if (mask == MAUDIO_SET_24B_48K_DI && altno != 2) 1182 return 1; /* skip this altsetting */ 1183 if (mask == MAUDIO_SET_24B_48K_NOTDI && altno != 3) 1184 return 1; /* skip this altsetting */ 1185 if (mask == MAUDIO_SET_16B_48K_DI && altno != 4) 1186 return 1; /* skip this altsetting */ 1187 if (mask == MAUDIO_SET_16B_48K_NOTDI && altno != 5) 1188 return 1; /* skip this altsetting */ 1189 } 1190 1191 return 0; /* keep this altsetting */ 1192 } 1193 1194 static int fasttrackpro_skip_setting_quirk(struct snd_usb_audio *chip, 1195 int iface, int altno) 1196 { 1197 /* Reset ALL ifaces to 0 altsetting. 1198 * Call it for every possible altsetting of every interface. 1199 */ 1200 usb_set_interface(chip->dev, iface, 0); 1201 1202 /* possible configuration where both inputs and only one output is 1203 *used is not supported by the current setup 1204 */ 1205 if (chip->setup & (MAUDIO_SET | MAUDIO_SET_24B)) { 1206 if (chip->setup & MAUDIO_SET_96K) { 1207 if (altno != 3 && altno != 6) 1208 return 1; 1209 } else if (chip->setup & MAUDIO_SET_DI) { 1210 if (iface == 4) 1211 return 1; /* no analog input */ 1212 if (altno != 2 && altno != 5) 1213 return 1; /* enable only altsets 2 and 5 */ 1214 } else { 1215 if (iface == 5) 1216 return 1; /* disable digialt input */ 1217 if (altno != 2 && altno != 5) 1218 return 1; /* enalbe only altsets 2 and 5 */ 1219 } 1220 } else { 1221 /* keep only 16-Bit mode */ 1222 if (altno != 1) 1223 return 1; 1224 } 1225 1226 usb_audio_dbg(chip, 1227 "using altsetting %d for interface %d config %d\n", 1228 altno, iface, chip->setup); 1229 return 0; /* keep this altsetting */ 1230 } 1231 1232 static int s1810c_skip_setting_quirk(struct snd_usb_audio *chip, 1233 int iface, int altno) 1234 { 1235 /* 1236 * Altno settings: 1237 * 1238 * Playback (Interface 1): 1239 * 1: 6 Analog + 2 S/PDIF 1240 * 2: 6 Analog + 2 S/PDIF 1241 * 3: 6 Analog 1242 * 1243 * Capture (Interface 2): 1244 * 1: 8 Analog + 2 S/PDIF + 8 ADAT 1245 * 2: 8 Analog + 2 S/PDIF + 4 ADAT 1246 * 3: 8 Analog 1247 */ 1248 1249 /* 1250 * I'll leave 2 as the default one and 1251 * use device_setup to switch to the 1252 * other two. 1253 */ 1254 if ((chip->setup == 0 || chip->setup > 2) && altno != 2) 1255 return 1; 1256 else if (chip->setup == 1 && altno != 1) 1257 return 1; 1258 else if (chip->setup == 2 && altno != 3) 1259 return 1; 1260 1261 return 0; 1262 } 1263 1264 int snd_usb_apply_interface_quirk(struct snd_usb_audio *chip, 1265 int iface, 1266 int altno) 1267 { 1268 /* audiophile usb: skip altsets incompatible with device_setup */ 1269 if (chip->usb_id == USB_ID(0x0763, 0x2003)) 1270 return audiophile_skip_setting_quirk(chip, iface, altno); 1271 /* quattro usb: skip altsets incompatible with device_setup */ 1272 if (chip->usb_id == USB_ID(0x0763, 0x2001)) 1273 return quattro_skip_setting_quirk(chip, iface, altno); 1274 /* fasttrackpro usb: skip altsets incompatible with device_setup */ 1275 if (chip->usb_id == USB_ID(0x0763, 0x2012)) 1276 return fasttrackpro_skip_setting_quirk(chip, iface, altno); 1277 /* presonus studio 1810c: skip altsets incompatible with device_setup */ 1278 if (chip->usb_id == USB_ID(0x0194f, 0x010c)) 1279 return s1810c_skip_setting_quirk(chip, iface, altno); 1280 1281 1282 return 0; 1283 } 1284 1285 int snd_usb_apply_boot_quirk(struct usb_device *dev, 1286 struct usb_interface *intf, 1287 const struct snd_usb_audio_quirk *quirk, 1288 unsigned int id) 1289 { 1290 switch (id) { 1291 case USB_ID(0x041e, 0x3000): 1292 /* SB Extigy needs special boot-up sequence */ 1293 /* if more models come, this will go to the quirk list. */ 1294 return snd_usb_extigy_boot_quirk(dev, intf); 1295 1296 case USB_ID(0x041e, 0x3020): 1297 /* SB Audigy 2 NX needs its own boot-up magic, too */ 1298 return snd_usb_audigy2nx_boot_quirk(dev); 1299 1300 case USB_ID(0x10f5, 0x0200): 1301 /* C-Media CM106 / Turtle Beach Audio Advantage Roadie */ 1302 return snd_usb_cm106_boot_quirk(dev); 1303 1304 case USB_ID(0x0d8c, 0x0102): 1305 /* C-Media CM6206 / CM106-Like Sound Device */ 1306 case USB_ID(0x0ccd, 0x00b1): /* Terratec Aureon 7.1 USB */ 1307 return snd_usb_cm6206_boot_quirk(dev); 1308 1309 case USB_ID(0x0dba, 0x3000): 1310 /* Digidesign Mbox 2 */ 1311 return snd_usb_mbox2_boot_quirk(dev); 1312 1313 case USB_ID(0x1235, 0x0010): /* Focusrite Novation Saffire 6 USB */ 1314 case USB_ID(0x1235, 0x0018): /* Focusrite Novation Twitch */ 1315 return snd_usb_novation_boot_quirk(dev); 1316 1317 case USB_ID(0x133e, 0x0815): 1318 /* Access Music VirusTI Desktop */ 1319 return snd_usb_accessmusic_boot_quirk(dev); 1320 1321 case USB_ID(0x17cc, 0x1000): /* Komplete Audio 6 */ 1322 case USB_ID(0x17cc, 0x1010): /* Traktor Audio 6 */ 1323 case USB_ID(0x17cc, 0x1020): /* Traktor Audio 10 */ 1324 return snd_usb_nativeinstruments_boot_quirk(dev); 1325 case USB_ID(0x0763, 0x2012): /* M-Audio Fast Track Pro USB */ 1326 return snd_usb_fasttrackpro_boot_quirk(dev); 1327 case USB_ID(0x047f, 0xc010): /* Plantronics Gamecom 780 */ 1328 return snd_usb_gamecon780_boot_quirk(dev); 1329 case USB_ID(0x2466, 0x8010): /* Fractal Audio Axe-Fx 3 */ 1330 return snd_usb_axefx3_boot_quirk(dev); 1331 case USB_ID(0x07fd, 0x0004): /* MOTU MicroBook II */ 1332 /* 1333 * For some reason interface 3 with vendor-spec class is 1334 * detected on MicroBook IIc. 1335 */ 1336 if (get_iface_desc(intf->altsetting)->bInterfaceClass == 1337 USB_CLASS_VENDOR_SPEC && 1338 get_iface_desc(intf->altsetting)->bInterfaceNumber < 3) 1339 return snd_usb_motu_microbookii_boot_quirk(dev); 1340 break; 1341 } 1342 1343 return 0; 1344 } 1345 1346 int snd_usb_apply_boot_quirk_once(struct usb_device *dev, 1347 struct usb_interface *intf, 1348 const struct snd_usb_audio_quirk *quirk, 1349 unsigned int id) 1350 { 1351 switch (id) { 1352 case USB_ID(0x07fd, 0x0008): /* MOTU M Series */ 1353 return snd_usb_motu_m_series_boot_quirk(dev); 1354 } 1355 1356 return 0; 1357 } 1358 1359 /* 1360 * check if the device uses big-endian samples 1361 */ 1362 int snd_usb_is_big_endian_format(struct snd_usb_audio *chip, 1363 const struct audioformat *fp) 1364 { 1365 /* it depends on altsetting whether the device is big-endian or not */ 1366 switch (chip->usb_id) { 1367 case USB_ID(0x0763, 0x2001): /* M-Audio Quattro: captured data only */ 1368 if (fp->altsetting == 2 || fp->altsetting == 3 || 1369 fp->altsetting == 5 || fp->altsetting == 6) 1370 return 1; 1371 break; 1372 case USB_ID(0x0763, 0x2003): /* M-Audio Audiophile USB */ 1373 if (chip->setup == 0x00 || 1374 fp->altsetting == 1 || fp->altsetting == 2 || 1375 fp->altsetting == 3) 1376 return 1; 1377 break; 1378 case USB_ID(0x0763, 0x2012): /* M-Audio Fast Track Pro */ 1379 if (fp->altsetting == 2 || fp->altsetting == 3 || 1380 fp->altsetting == 5 || fp->altsetting == 6) 1381 return 1; 1382 break; 1383 } 1384 return 0; 1385 } 1386 1387 /* 1388 * For E-Mu 0404USB/0202USB/TrackerPre/0204 sample rate should be set for device, 1389 * not for interface. 1390 */ 1391 1392 enum { 1393 EMU_QUIRK_SR_44100HZ = 0, 1394 EMU_QUIRK_SR_48000HZ, 1395 EMU_QUIRK_SR_88200HZ, 1396 EMU_QUIRK_SR_96000HZ, 1397 EMU_QUIRK_SR_176400HZ, 1398 EMU_QUIRK_SR_192000HZ 1399 }; 1400 1401 static void set_format_emu_quirk(struct snd_usb_substream *subs, 1402 const struct audioformat *fmt) 1403 { 1404 unsigned char emu_samplerate_id = 0; 1405 1406 /* When capture is active 1407 * sample rate shouldn't be changed 1408 * by playback substream 1409 */ 1410 if (subs->direction == SNDRV_PCM_STREAM_PLAYBACK) { 1411 if (subs->stream->substream[SNDRV_PCM_STREAM_CAPTURE].cur_audiofmt) 1412 return; 1413 } 1414 1415 switch (fmt->rate_min) { 1416 case 48000: 1417 emu_samplerate_id = EMU_QUIRK_SR_48000HZ; 1418 break; 1419 case 88200: 1420 emu_samplerate_id = EMU_QUIRK_SR_88200HZ; 1421 break; 1422 case 96000: 1423 emu_samplerate_id = EMU_QUIRK_SR_96000HZ; 1424 break; 1425 case 176400: 1426 emu_samplerate_id = EMU_QUIRK_SR_176400HZ; 1427 break; 1428 case 192000: 1429 emu_samplerate_id = EMU_QUIRK_SR_192000HZ; 1430 break; 1431 default: 1432 emu_samplerate_id = EMU_QUIRK_SR_44100HZ; 1433 break; 1434 } 1435 snd_emuusb_set_samplerate(subs->stream->chip, emu_samplerate_id); 1436 subs->pkt_offset_adj = (emu_samplerate_id >= EMU_QUIRK_SR_176400HZ) ? 4 : 0; 1437 } 1438 1439 1440 /* 1441 * Pioneer DJ DJM-900NXS2 1442 * Device needs to know the sample rate each time substream is started 1443 */ 1444 static int pioneer_djm_set_format_quirk(struct snd_usb_substream *subs) 1445 { 1446 unsigned int cur_rate = subs->data_endpoint->cur_rate; 1447 /* Convert sample rate value to little endian */ 1448 u8 sr[3]; 1449 1450 sr[0] = cur_rate & 0xff; 1451 sr[1] = (cur_rate >> 8) & 0xff; 1452 sr[2] = (cur_rate >> 16) & 0xff; 1453 1454 /* Configure device */ 1455 usb_set_interface(subs->dev, 0, 1); 1456 snd_usb_ctl_msg(subs->stream->chip->dev, 1457 usb_rcvctrlpipe(subs->stream->chip->dev, 0), 1458 0x01, 0x22, 0x0100, 0x0082, &sr, 0x0003); 1459 1460 return 0; 1461 } 1462 1463 void snd_usb_set_format_quirk(struct snd_usb_substream *subs, 1464 const struct audioformat *fmt) 1465 { 1466 switch (subs->stream->chip->usb_id) { 1467 case USB_ID(0x041e, 0x3f02): /* E-Mu 0202 USB */ 1468 case USB_ID(0x041e, 0x3f04): /* E-Mu 0404 USB */ 1469 case USB_ID(0x041e, 0x3f0a): /* E-Mu Tracker Pre */ 1470 case USB_ID(0x041e, 0x3f19): /* E-Mu 0204 USB */ 1471 set_format_emu_quirk(subs, fmt); 1472 break; 1473 case USB_ID(0x2b73, 0x000a): /* Pioneer DJ DJM-900NXS2 */ 1474 case USB_ID(0x2b73, 0x0017): /* Pioneer DJ DJM-250MK2 */ 1475 pioneer_djm_set_format_quirk(subs); 1476 break; 1477 case USB_ID(0x534d, 0x2109): /* MacroSilicon MS2109 */ 1478 subs->stream_offset_adj = 2; 1479 break; 1480 } 1481 } 1482 1483 bool snd_usb_get_sample_rate_quirk(struct snd_usb_audio *chip) 1484 { 1485 /* devices which do not support reading the sample rate. */ 1486 switch (chip->usb_id) { 1487 case USB_ID(0x041e, 0x4080): /* Creative Live Cam VF0610 */ 1488 case USB_ID(0x04d8, 0xfeea): /* Benchmark DAC1 Pre */ 1489 case USB_ID(0x0556, 0x0014): /* Phoenix Audio TMX320VC */ 1490 case USB_ID(0x05a3, 0x9420): /* ELP HD USB Camera */ 1491 case USB_ID(0x05a7, 0x1020): /* Bose Companion 5 */ 1492 case USB_ID(0x074d, 0x3553): /* Outlaw RR2150 (Micronas UAC3553B) */ 1493 case USB_ID(0x1395, 0x740a): /* Sennheiser DECT */ 1494 case USB_ID(0x1901, 0x0191): /* GE B850V3 CP2114 audio interface */ 1495 case USB_ID(0x21b4, 0x0081): /* AudioQuest DragonFly */ 1496 case USB_ID(0x2912, 0x30c8): /* Audioengine D1 */ 1497 return true; 1498 } 1499 1500 /* devices of these vendors don't support reading rate, either */ 1501 switch (USB_ID_VENDOR(chip->usb_id)) { 1502 case 0x045e: /* MS Lifecam */ 1503 case 0x047f: /* Plantronics */ 1504 case 0x1de7: /* Phoenix Audio */ 1505 return true; 1506 } 1507 1508 return false; 1509 } 1510 1511 /* ITF-USB DSD based DACs need a vendor cmd to switch 1512 * between PCM and native DSD mode 1513 */ 1514 static bool is_itf_usb_dsd_dac(unsigned int id) 1515 { 1516 switch (id) { 1517 case USB_ID(0x154e, 0x1002): /* Denon DCD-1500RE */ 1518 case USB_ID(0x154e, 0x1003): /* Denon DA-300USB */ 1519 case USB_ID(0x154e, 0x3005): /* Marantz HD-DAC1 */ 1520 case USB_ID(0x154e, 0x3006): /* Marantz SA-14S1 */ 1521 case USB_ID(0x1852, 0x5065): /* Luxman DA-06 */ 1522 case USB_ID(0x0644, 0x8043): /* TEAC UD-501/UD-501V2/UD-503/NT-503 */ 1523 case USB_ID(0x0644, 0x8044): /* Esoteric D-05X */ 1524 case USB_ID(0x0644, 0x804a): /* TEAC UD-301 */ 1525 return true; 1526 } 1527 return false; 1528 } 1529 1530 int snd_usb_select_mode_quirk(struct snd_usb_audio *chip, 1531 const struct audioformat *fmt) 1532 { 1533 struct usb_device *dev = chip->dev; 1534 int err; 1535 1536 if (is_itf_usb_dsd_dac(chip->usb_id)) { 1537 /* First switch to alt set 0, otherwise the mode switch cmd 1538 * will not be accepted by the DAC 1539 */ 1540 err = usb_set_interface(dev, fmt->iface, 0); 1541 if (err < 0) 1542 return err; 1543 1544 msleep(20); /* Delay needed after setting the interface */ 1545 1546 /* Vendor mode switch cmd is required. */ 1547 if (fmt->formats & SNDRV_PCM_FMTBIT_DSD_U32_BE) { 1548 /* DSD mode (DSD_U32) requested */ 1549 err = snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), 0, 1550 USB_DIR_OUT|USB_TYPE_VENDOR|USB_RECIP_INTERFACE, 1551 1, 1, NULL, 0); 1552 if (err < 0) 1553 return err; 1554 1555 } else { 1556 /* PCM or DOP mode (S32) requested */ 1557 /* PCM mode (S16) requested */ 1558 err = snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), 0, 1559 USB_DIR_OUT|USB_TYPE_VENDOR|USB_RECIP_INTERFACE, 1560 0, 1, NULL, 0); 1561 if (err < 0) 1562 return err; 1563 1564 } 1565 msleep(20); 1566 } 1567 return 0; 1568 } 1569 1570 void snd_usb_endpoint_start_quirk(struct snd_usb_endpoint *ep) 1571 { 1572 /* 1573 * "Playback Design" products send bogus feedback data at the start 1574 * of the stream. Ignore them. 1575 */ 1576 if (USB_ID_VENDOR(ep->chip->usb_id) == 0x23ba && 1577 ep->type == SND_USB_ENDPOINT_TYPE_SYNC) 1578 ep->skip_packets = 4; 1579 1580 /* 1581 * M-Audio Fast Track C400/C600 - when packets are not skipped, real 1582 * world latency varies by approx. +/- 50 frames (at 96kHz) each time 1583 * the stream is (re)started. When skipping packets 16 at endpoint 1584 * start up, the real world latency is stable within +/- 1 frame (also 1585 * across power cycles). 1586 */ 1587 if ((ep->chip->usb_id == USB_ID(0x0763, 0x2030) || 1588 ep->chip->usb_id == USB_ID(0x0763, 0x2031)) && 1589 ep->type == SND_USB_ENDPOINT_TYPE_DATA) 1590 ep->skip_packets = 16; 1591 1592 /* Work around devices that report unreasonable feedback data */ 1593 if ((ep->chip->usb_id == USB_ID(0x0644, 0x8038) || /* TEAC UD-H01 */ 1594 ep->chip->usb_id == USB_ID(0x1852, 0x5034)) && /* T+A Dac8 */ 1595 ep->syncmaxsize == 4) 1596 ep->tenor_fb_quirk = 1; 1597 } 1598 1599 void snd_usb_set_interface_quirk(struct snd_usb_audio *chip) 1600 { 1601 if (!chip) 1602 return; 1603 /* 1604 * "Playback Design" products need a 50ms delay after setting the 1605 * USB interface. 1606 */ 1607 switch (USB_ID_VENDOR(chip->usb_id)) { 1608 case 0x23ba: /* Playback Design */ 1609 case 0x0644: /* TEAC Corp. */ 1610 msleep(50); 1611 break; 1612 } 1613 } 1614 1615 /* quirk applied after snd_usb_ctl_msg(); not applied during boot quirks */ 1616 void snd_usb_ctl_msg_quirk(struct usb_device *dev, unsigned int pipe, 1617 __u8 request, __u8 requesttype, __u16 value, 1618 __u16 index, void *data, __u16 size) 1619 { 1620 struct snd_usb_audio *chip = dev_get_drvdata(&dev->dev); 1621 1622 if (!chip) 1623 return; 1624 /* 1625 * "Playback Design" products need a 20ms delay after each 1626 * class compliant request 1627 */ 1628 if (USB_ID_VENDOR(chip->usb_id) == 0x23ba && 1629 (requesttype & USB_TYPE_MASK) == USB_TYPE_CLASS) 1630 msleep(20); 1631 1632 /* 1633 * "TEAC Corp." products need a 20ms delay after each 1634 * class compliant request 1635 */ 1636 if (USB_ID_VENDOR(chip->usb_id) == 0x0644 && 1637 (requesttype & USB_TYPE_MASK) == USB_TYPE_CLASS) 1638 msleep(20); 1639 1640 /* ITF-USB DSD based DACs functionality need a delay 1641 * after each class compliant request 1642 */ 1643 if (is_itf_usb_dsd_dac(chip->usb_id) 1644 && (requesttype & USB_TYPE_MASK) == USB_TYPE_CLASS) 1645 msleep(20); 1646 1647 /* Zoom R16/24, many Logitech(at least H650e/H570e/BCC950), 1648 * Jabra 550a, Kingston HyperX needs a tiny delay here, 1649 * otherwise requests like get/set frequency return 1650 * as failed despite actually succeeding. 1651 */ 1652 if ((chip->usb_id == USB_ID(0x1686, 0x00dd) || 1653 USB_ID_VENDOR(chip->usb_id) == 0x046d || /* Logitech */ 1654 chip->usb_id == USB_ID(0x0b0e, 0x0349) || 1655 chip->usb_id == USB_ID(0x0951, 0x16ad)) && 1656 (requesttype & USB_TYPE_MASK) == USB_TYPE_CLASS) 1657 usleep_range(1000, 2000); 1658 1659 /* 1660 * Samsung USBC Headset (AKG) need a tiny delay after each 1661 * class compliant request. (Model number: AAM625R or AAM627R) 1662 */ 1663 if (chip->usb_id == USB_ID(0x04e8, 0xa051) && 1664 (requesttype & USB_TYPE_MASK) == USB_TYPE_CLASS) 1665 usleep_range(5000, 6000); 1666 } 1667 1668 /* 1669 * snd_usb_interface_dsd_format_quirks() is called from format.c to 1670 * augment the PCM format bit-field for DSD types. The UAC standards 1671 * don't have a designated bit field to denote DSD-capable interfaces, 1672 * hence all hardware that is known to support this format has to be 1673 * listed here. 1674 */ 1675 u64 snd_usb_interface_dsd_format_quirks(struct snd_usb_audio *chip, 1676 struct audioformat *fp, 1677 unsigned int sample_bytes) 1678 { 1679 struct usb_interface *iface; 1680 1681 /* Playback Designs */ 1682 if (USB_ID_VENDOR(chip->usb_id) == 0x23ba && 1683 USB_ID_PRODUCT(chip->usb_id) < 0x0110) { 1684 switch (fp->altsetting) { 1685 case 1: 1686 fp->dsd_dop = true; 1687 return SNDRV_PCM_FMTBIT_DSD_U16_LE; 1688 case 2: 1689 fp->dsd_bitrev = true; 1690 return SNDRV_PCM_FMTBIT_DSD_U8; 1691 case 3: 1692 fp->dsd_bitrev = true; 1693 return SNDRV_PCM_FMTBIT_DSD_U16_LE; 1694 } 1695 } 1696 1697 /* XMOS based USB DACs */ 1698 switch (chip->usb_id) { 1699 case USB_ID(0x1511, 0x0037): /* AURALiC VEGA */ 1700 case USB_ID(0x2522, 0x0012): /* LH Labs VI DAC Infinity */ 1701 case USB_ID(0x2772, 0x0230): /* Pro-Ject Pre Box S2 Digital */ 1702 if (fp->altsetting == 2) 1703 return SNDRV_PCM_FMTBIT_DSD_U32_BE; 1704 break; 1705 1706 case USB_ID(0x0d8c, 0x0316): /* Hegel HD12 DSD */ 1707 case USB_ID(0x10cb, 0x0103): /* The Bit Opus #3; with fp->dsd_raw */ 1708 case USB_ID(0x16d0, 0x06b2): /* NuPrime DAC-10 */ 1709 case USB_ID(0x16d0, 0x09dd): /* Encore mDSD */ 1710 case USB_ID(0x16d0, 0x0733): /* Furutech ADL Stratos */ 1711 case USB_ID(0x16d0, 0x09db): /* NuPrime Audio DAC-9 */ 1712 case USB_ID(0x1db5, 0x0003): /* Bryston BDA3 */ 1713 case USB_ID(0x22e1, 0xca01): /* HDTA Serenade DSD */ 1714 case USB_ID(0x249c, 0x9326): /* M2Tech Young MkIII */ 1715 case USB_ID(0x2616, 0x0106): /* PS Audio NuWave DAC */ 1716 case USB_ID(0x2622, 0x0041): /* Audiolab M-DAC+ */ 1717 case USB_ID(0x27f7, 0x3002): /* W4S DAC-2v2SE */ 1718 case USB_ID(0x29a2, 0x0086): /* Mutec MC3+ USB */ 1719 case USB_ID(0x6b42, 0x0042): /* MSB Technology */ 1720 if (fp->altsetting == 3) 1721 return SNDRV_PCM_FMTBIT_DSD_U32_BE; 1722 break; 1723 1724 /* Amanero Combo384 USB based DACs with native DSD support */ 1725 case USB_ID(0x16d0, 0x071a): /* Amanero - Combo384 */ 1726 case USB_ID(0x2ab6, 0x0004): /* T+A DAC8DSD-V2.0, MP1000E-V2.0, MP2000R-V2.0, MP2500R-V2.0, MP3100HV-V2.0 */ 1727 case USB_ID(0x2ab6, 0x0005): /* T+A USB HD Audio 1 */ 1728 case USB_ID(0x2ab6, 0x0006): /* T+A USB HD Audio 2 */ 1729 if (fp->altsetting == 2) { 1730 switch (le16_to_cpu(chip->dev->descriptor.bcdDevice)) { 1731 case 0x199: 1732 return SNDRV_PCM_FMTBIT_DSD_U32_LE; 1733 case 0x19b: 1734 case 0x203: 1735 return SNDRV_PCM_FMTBIT_DSD_U32_BE; 1736 default: 1737 break; 1738 } 1739 } 1740 break; 1741 case USB_ID(0x16d0, 0x0a23): 1742 if (fp->altsetting == 2) 1743 return SNDRV_PCM_FMTBIT_DSD_U32_BE; 1744 break; 1745 1746 default: 1747 break; 1748 } 1749 1750 /* ITF-USB DSD based DACs */ 1751 if (is_itf_usb_dsd_dac(chip->usb_id)) { 1752 iface = usb_ifnum_to_if(chip->dev, fp->iface); 1753 1754 /* Altsetting 2 support native DSD if the num of altsets is 1755 * three (0-2), 1756 * Altsetting 3 support native DSD if the num of altsets is 1757 * four (0-3). 1758 */ 1759 if (fp->altsetting == iface->num_altsetting - 1) 1760 return SNDRV_PCM_FMTBIT_DSD_U32_BE; 1761 } 1762 1763 /* Mostly generic method to detect many DSD-capable implementations - 1764 * from XMOS/Thesycon 1765 */ 1766 switch (USB_ID_VENDOR(chip->usb_id)) { 1767 case 0x152a: /* Thesycon devices */ 1768 case 0x20b1: /* XMOS based devices */ 1769 case 0x22d9: /* Oppo */ 1770 case 0x23ba: /* Playback Designs */ 1771 case 0x25ce: /* Mytek devices */ 1772 case 0x278b: /* Rotel? */ 1773 case 0x292b: /* Gustard/Ess based devices */ 1774 case 0x2972: /* FiiO devices */ 1775 case 0x2ab6: /* T+A devices */ 1776 case 0x3353: /* Khadas devices */ 1777 case 0x3842: /* EVGA */ 1778 case 0xc502: /* HiBy devices */ 1779 if (fp->dsd_raw) 1780 return SNDRV_PCM_FMTBIT_DSD_U32_BE; 1781 break; 1782 default: 1783 break; 1784 1785 } 1786 1787 return 0; 1788 } 1789 1790 void snd_usb_audioformat_attributes_quirk(struct snd_usb_audio *chip, 1791 struct audioformat *fp, 1792 int stream) 1793 { 1794 switch (chip->usb_id) { 1795 case USB_ID(0x0a92, 0x0053): /* AudioTrak Optoplay */ 1796 /* Optoplay sets the sample rate attribute although 1797 * it seems not supporting it in fact. 1798 */ 1799 fp->attributes &= ~UAC_EP_CS_ATTR_SAMPLE_RATE; 1800 break; 1801 case USB_ID(0x041e, 0x3020): /* Creative SB Audigy 2 NX */ 1802 case USB_ID(0x0763, 0x2003): /* M-Audio Audiophile USB */ 1803 /* doesn't set the sample rate attribute, but supports it */ 1804 fp->attributes |= UAC_EP_CS_ATTR_SAMPLE_RATE; 1805 break; 1806 case USB_ID(0x0763, 0x2001): /* M-Audio Quattro USB */ 1807 case USB_ID(0x0763, 0x2012): /* M-Audio Fast Track Pro USB */ 1808 case USB_ID(0x047f, 0x0ca1): /* plantronics headset */ 1809 case USB_ID(0x077d, 0x07af): /* Griffin iMic (note that there is 1810 an older model 77d:223) */ 1811 /* 1812 * plantronics headset and Griffin iMic have set adaptive-in 1813 * although it's really not... 1814 */ 1815 fp->ep_attr &= ~USB_ENDPOINT_SYNCTYPE; 1816 if (stream == SNDRV_PCM_STREAM_PLAYBACK) 1817 fp->ep_attr |= USB_ENDPOINT_SYNC_ADAPTIVE; 1818 else 1819 fp->ep_attr |= USB_ENDPOINT_SYNC_SYNC; 1820 break; 1821 case USB_ID(0x07fd, 0x0004): /* MOTU MicroBook IIc */ 1822 /* 1823 * MaxPacketsOnly attribute is erroneously set in endpoint 1824 * descriptors. As a result this card produces noise with 1825 * all sample rates other than 96 kHz. 1826 */ 1827 fp->attributes &= ~UAC_EP_CS_ATTR_FILL_MAX; 1828 break; 1829 } 1830 } 1831 1832 /* 1833 * registration quirk: 1834 * the registration is skipped if a device matches with the given ID, 1835 * unless the interface reaches to the defined one. This is for delaying 1836 * the registration until the last known interface, so that the card and 1837 * devices appear at the same time. 1838 */ 1839 1840 struct registration_quirk { 1841 unsigned int usb_id; /* composed via USB_ID() */ 1842 unsigned int interface; /* the interface to trigger register */ 1843 }; 1844 1845 #define REG_QUIRK_ENTRY(vendor, product, iface) \ 1846 { .usb_id = USB_ID(vendor, product), .interface = (iface) } 1847 1848 static const struct registration_quirk registration_quirks[] = { 1849 REG_QUIRK_ENTRY(0x0951, 0x16d8, 2), /* Kingston HyperX AMP */ 1850 REG_QUIRK_ENTRY(0x0951, 0x16ed, 2), /* Kingston HyperX Cloud Alpha S */ 1851 REG_QUIRK_ENTRY(0x0951, 0x16ea, 2), /* Kingston HyperX Cloud Flight S */ 1852 { 0 } /* terminator */ 1853 }; 1854 1855 /* return true if skipping registration */ 1856 bool snd_usb_registration_quirk(struct snd_usb_audio *chip, int iface) 1857 { 1858 const struct registration_quirk *q; 1859 1860 for (q = registration_quirks; q->usb_id; q++) 1861 if (chip->usb_id == q->usb_id) 1862 return iface != q->interface; 1863 1864 /* Register as normal */ 1865 return false; 1866 } 1867