1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Driver for DBRI sound chip found on Sparcs. 4 * Copyright (C) 2004, 2005 Martin Habets (mhabets@users.sourceforge.net) 5 * 6 * Converted to ring buffered version by Krzysztof Helt (krzysztof.h1@wp.pl) 7 * 8 * Based entirely upon drivers/sbus/audio/dbri.c which is: 9 * Copyright (C) 1997 Rudolf Koenig (rfkoenig@immd4.informatik.uni-erlangen.de) 10 * Copyright (C) 1998, 1999 Brent Baccala (baccala@freesoft.org) 11 * 12 * This is the low level driver for the DBRI & MMCODEC duo used for ISDN & AUDIO 13 * on Sun SPARCStation 10, 20, LX and Voyager models. 14 * 15 * - DBRI: AT&T T5900FX Dual Basic Rates ISDN Interface. It is a 32 channel 16 * data time multiplexer with ISDN support (aka T7259) 17 * Interfaces: SBus,ISDN NT & TE, CHI, 4 bits parallel. 18 * CHI: (spelled ki) Concentration Highway Interface (AT&T or Intel bus ?). 19 * Documentation: 20 * - "STP 4000SBus Dual Basic Rate ISDN (DBRI) Transceiver" from 21 * Sparc Technology Business (courtesy of Sun Support) 22 * - Data sheet of the T7903, a newer but very similar ISA bus equivalent 23 * available from the Lucent (formerly AT&T microelectronics) home 24 * page. 25 * - http://www.freesoft.org/Linux/DBRI/ 26 * - MMCODEC: Crystal Semiconductor CS4215 16 bit Multimedia Audio Codec 27 * Interfaces: CHI, Audio In & Out, 2 bits parallel 28 * Documentation: from the Crystal Semiconductor home page. 29 * 30 * The DBRI is a 32 pipe machine, each pipe can transfer some bits between 31 * memory and a serial device (long pipes, no. 0-15) or between two serial 32 * devices (short pipes, no. 16-31), or simply send a fixed data to a serial 33 * device (short pipes). 34 * A timeslot defines the bit-offset and no. of bits read from a serial device. 35 * The timeslots are linked to 6 circular lists, one for each direction for 36 * each serial device (NT,TE,CHI). A timeslot is associated to 1 or 2 pipes 37 * (the second one is a monitor/tee pipe, valid only for serial input). 38 * 39 * The mmcodec is connected via the CHI bus and needs the data & some 40 * parameters (volume, output selection) time multiplexed in 8 byte 41 * chunks. It also has a control mode, which serves for audio format setting. 42 * 43 * Looking at the CS4215 data sheet it is easy to set up 2 or 4 codecs on 44 * the same CHI bus, so I thought perhaps it is possible to use the on-board 45 * & the speakerbox codec simultaneously, giving 2 (not very independent :-) 46 * audio devices. But the SUN HW group decided against it, at least on my 47 * LX the speakerbox connector has at least 1 pin missing and 1 wrongly 48 * connected. 49 * 50 * I've tried to stick to the following function naming conventions: 51 * snd_* ALSA stuff 52 * cs4215_* CS4215 codec specific stuff 53 * dbri_* DBRI high-level stuff 54 * other DBRI low-level stuff 55 */ 56 57 #include <linux/interrupt.h> 58 #include <linux/delay.h> 59 #include <linux/irq.h> 60 #include <linux/io.h> 61 #include <linux/dma-mapping.h> 62 #include <linux/gfp.h> 63 64 #include <sound/core.h> 65 #include <sound/pcm.h> 66 #include <sound/pcm_params.h> 67 #include <sound/info.h> 68 #include <sound/control.h> 69 #include <sound/initval.h> 70 71 #include <linux/of.h> 72 #include <linux/of_device.h> 73 #include <linux/atomic.h> 74 #include <linux/module.h> 75 76 MODULE_AUTHOR("Rudolf Koenig, Brent Baccala and Martin Habets"); 77 MODULE_DESCRIPTION("Sun DBRI"); 78 MODULE_LICENSE("GPL"); 79 MODULE_SUPPORTED_DEVICE("{{Sun,DBRI}}"); 80 81 static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX; /* Index 0-MAX */ 82 static char *id[SNDRV_CARDS] = SNDRV_DEFAULT_STR; /* ID for this card */ 83 /* Enable this card */ 84 static bool enable[SNDRV_CARDS] = SNDRV_DEFAULT_ENABLE_PNP; 85 86 module_param_array(index, int, NULL, 0444); 87 MODULE_PARM_DESC(index, "Index value for Sun DBRI soundcard."); 88 module_param_array(id, charp, NULL, 0444); 89 MODULE_PARM_DESC(id, "ID string for Sun DBRI soundcard."); 90 module_param_array(enable, bool, NULL, 0444); 91 MODULE_PARM_DESC(enable, "Enable Sun DBRI soundcard."); 92 93 #undef DBRI_DEBUG 94 95 #define D_INT (1<<0) 96 #define D_GEN (1<<1) 97 #define D_CMD (1<<2) 98 #define D_MM (1<<3) 99 #define D_USR (1<<4) 100 #define D_DESC (1<<5) 101 102 static int dbri_debug; 103 module_param(dbri_debug, int, 0644); 104 MODULE_PARM_DESC(dbri_debug, "Debug value for Sun DBRI soundcard."); 105 106 #ifdef DBRI_DEBUG 107 static char *cmds[] = { 108 "WAIT", "PAUSE", "JUMP", "IIQ", "REX", "SDP", "CDP", "DTS", 109 "SSP", "CHI", "NT", "TE", "CDEC", "TEST", "CDM", "RESRV" 110 }; 111 112 #define dprintk(a, x...) if (dbri_debug & a) printk(KERN_DEBUG x) 113 114 #else 115 #define dprintk(a, x...) do { } while (0) 116 117 #endif /* DBRI_DEBUG */ 118 119 #define DBRI_CMD(cmd, intr, value) ((cmd << 28) | \ 120 (intr << 27) | \ 121 value) 122 123 /*************************************************************************** 124 CS4215 specific definitions and structures 125 ****************************************************************************/ 126 127 struct cs4215 { 128 __u8 data[4]; /* Data mode: Time slots 5-8 */ 129 __u8 ctrl[4]; /* Ctrl mode: Time slots 1-4 */ 130 __u8 onboard; 131 __u8 offset; /* Bit offset from frame sync to time slot 1 */ 132 volatile __u32 status; 133 volatile __u32 version; 134 __u8 precision; /* In bits, either 8 or 16 */ 135 __u8 channels; /* 1 or 2 */ 136 }; 137 138 /* 139 * Control mode first 140 */ 141 142 /* Time Slot 1, Status register */ 143 #define CS4215_CLB (1<<2) /* Control Latch Bit */ 144 #define CS4215_OLB (1<<3) /* 1: line: 2.0V, speaker 4V */ 145 /* 0: line: 2.8V, speaker 8V */ 146 #define CS4215_MLB (1<<4) /* 1: Microphone: 20dB gain disabled */ 147 #define CS4215_RSRVD_1 (1<<5) 148 149 /* Time Slot 2, Data Format Register */ 150 #define CS4215_DFR_LINEAR16 0 151 #define CS4215_DFR_ULAW 1 152 #define CS4215_DFR_ALAW 2 153 #define CS4215_DFR_LINEAR8 3 154 #define CS4215_DFR_STEREO (1<<2) 155 static struct { 156 unsigned short freq; 157 unsigned char xtal; 158 unsigned char csval; 159 } CS4215_FREQ[] = { 160 { 8000, (1 << 4), (0 << 3) }, 161 { 16000, (1 << 4), (1 << 3) }, 162 { 27429, (1 << 4), (2 << 3) }, /* Actually 24428.57 */ 163 { 32000, (1 << 4), (3 << 3) }, 164 /* { NA, (1 << 4), (4 << 3) }, */ 165 /* { NA, (1 << 4), (5 << 3) }, */ 166 { 48000, (1 << 4), (6 << 3) }, 167 { 9600, (1 << 4), (7 << 3) }, 168 { 5512, (2 << 4), (0 << 3) }, /* Actually 5512.5 */ 169 { 11025, (2 << 4), (1 << 3) }, 170 { 18900, (2 << 4), (2 << 3) }, 171 { 22050, (2 << 4), (3 << 3) }, 172 { 37800, (2 << 4), (4 << 3) }, 173 { 44100, (2 << 4), (5 << 3) }, 174 { 33075, (2 << 4), (6 << 3) }, 175 { 6615, (2 << 4), (7 << 3) }, 176 { 0, 0, 0} 177 }; 178 179 #define CS4215_HPF (1<<7) /* High Pass Filter, 1: Enabled */ 180 181 #define CS4215_12_MASK 0xfcbf /* Mask off reserved bits in slot 1 & 2 */ 182 183 /* Time Slot 3, Serial Port Control register */ 184 #define CS4215_XEN (1<<0) /* 0: Enable serial output */ 185 #define CS4215_XCLK (1<<1) /* 1: Master mode: Generate SCLK */ 186 #define CS4215_BSEL_64 (0<<2) /* Bitrate: 64 bits per frame */ 187 #define CS4215_BSEL_128 (1<<2) 188 #define CS4215_BSEL_256 (2<<2) 189 #define CS4215_MCK_MAST (0<<4) /* Master clock */ 190 #define CS4215_MCK_XTL1 (1<<4) /* 24.576 MHz clock source */ 191 #define CS4215_MCK_XTL2 (2<<4) /* 16.9344 MHz clock source */ 192 #define CS4215_MCK_CLK1 (3<<4) /* Clockin, 256 x Fs */ 193 #define CS4215_MCK_CLK2 (4<<4) /* Clockin, see DFR */ 194 195 /* Time Slot 4, Test Register */ 196 #define CS4215_DAD (1<<0) /* 0:Digital-Dig loop, 1:Dig-Analog-Dig loop */ 197 #define CS4215_ENL (1<<1) /* Enable Loopback Testing */ 198 199 /* Time Slot 5, Parallel Port Register */ 200 /* Read only here and the same as the in data mode */ 201 202 /* Time Slot 6, Reserved */ 203 204 /* Time Slot 7, Version Register */ 205 #define CS4215_VERSION_MASK 0xf /* Known versions 0/C, 1/D, 2/E */ 206 207 /* Time Slot 8, Reserved */ 208 209 /* 210 * Data mode 211 */ 212 /* Time Slot 1-2: Left Channel Data, 2-3: Right Channel Data */ 213 214 /* Time Slot 5, Output Setting */ 215 #define CS4215_LO(v) v /* Left Output Attenuation 0x3f: -94.5 dB */ 216 #define CS4215_LE (1<<6) /* Line Out Enable */ 217 #define CS4215_HE (1<<7) /* Headphone Enable */ 218 219 /* Time Slot 6, Output Setting */ 220 #define CS4215_RO(v) v /* Right Output Attenuation 0x3f: -94.5 dB */ 221 #define CS4215_SE (1<<6) /* Speaker Enable */ 222 #define CS4215_ADI (1<<7) /* A/D Data Invalid: Busy in calibration */ 223 224 /* Time Slot 7, Input Setting */ 225 #define CS4215_LG(v) v /* Left Gain Setting 0xf: 22.5 dB */ 226 #define CS4215_IS (1<<4) /* Input Select: 1=Microphone, 0=Line */ 227 #define CS4215_OVR (1<<5) /* 1: Over range condition occurred */ 228 #define CS4215_PIO0 (1<<6) /* Parallel I/O 0 */ 229 #define CS4215_PIO1 (1<<7) 230 231 /* Time Slot 8, Input Setting */ 232 #define CS4215_RG(v) v /* Right Gain Setting 0xf: 22.5 dB */ 233 #define CS4215_MA(v) (v<<4) /* Monitor Path Attenuation 0xf: mute */ 234 235 /*************************************************************************** 236 DBRI specific definitions and structures 237 ****************************************************************************/ 238 239 /* DBRI main registers */ 240 #define REG0 0x00 /* Status and Control */ 241 #define REG1 0x04 /* Mode and Interrupt */ 242 #define REG2 0x08 /* Parallel IO */ 243 #define REG3 0x0c /* Test */ 244 #define REG8 0x20 /* Command Queue Pointer */ 245 #define REG9 0x24 /* Interrupt Queue Pointer */ 246 247 #define DBRI_NO_CMDS 64 248 #define DBRI_INT_BLK 64 249 #define DBRI_NO_DESCS 64 250 #define DBRI_NO_PIPES 32 251 #define DBRI_MAX_PIPE (DBRI_NO_PIPES - 1) 252 253 #define DBRI_REC 0 254 #define DBRI_PLAY 1 255 #define DBRI_NO_STREAMS 2 256 257 /* One transmit/receive descriptor */ 258 /* When ba != 0 descriptor is used */ 259 struct dbri_mem { 260 volatile __u32 word1; 261 __u32 ba; /* Transmit/Receive Buffer Address */ 262 __u32 nda; /* Next Descriptor Address */ 263 volatile __u32 word4; 264 }; 265 266 /* This structure is in a DMA region where it can accessed by both 267 * the CPU and the DBRI 268 */ 269 struct dbri_dma { 270 s32 cmd[DBRI_NO_CMDS]; /* Place for commands */ 271 volatile s32 intr[DBRI_INT_BLK]; /* Interrupt field */ 272 struct dbri_mem desc[DBRI_NO_DESCS]; /* Xmit/receive descriptors */ 273 }; 274 275 #define dbri_dma_off(member, elem) \ 276 ((u32)(unsigned long) \ 277 (&(((struct dbri_dma *)0)->member[elem]))) 278 279 enum in_or_out { PIPEinput, PIPEoutput }; 280 281 struct dbri_pipe { 282 u32 sdp; /* SDP command word */ 283 int nextpipe; /* Next pipe in linked list */ 284 int length; /* Length of timeslot (bits) */ 285 int first_desc; /* Index of first descriptor */ 286 int desc; /* Index of active descriptor */ 287 volatile __u32 *recv_fixed_ptr; /* Ptr to receive fixed data */ 288 }; 289 290 /* Per stream (playback or record) information */ 291 struct dbri_streaminfo { 292 struct snd_pcm_substream *substream; 293 u32 dvma_buffer; /* Device view of ALSA DMA buffer */ 294 int size; /* Size of DMA buffer */ 295 size_t offset; /* offset in user buffer */ 296 int pipe; /* Data pipe used */ 297 int left_gain; /* mixer elements */ 298 int right_gain; 299 }; 300 301 /* This structure holds the information for both chips (DBRI & CS4215) */ 302 struct snd_dbri { 303 int regs_size, irq; /* Needed for unload */ 304 struct platform_device *op; /* OF device info */ 305 spinlock_t lock; 306 307 struct dbri_dma *dma; /* Pointer to our DMA block */ 308 dma_addr_t dma_dvma; /* DBRI visible DMA address */ 309 310 void __iomem *regs; /* dbri HW regs */ 311 int dbri_irqp; /* intr queue pointer */ 312 313 struct dbri_pipe pipes[DBRI_NO_PIPES]; /* DBRI's 32 data pipes */ 314 int next_desc[DBRI_NO_DESCS]; /* Index of next desc, or -1 */ 315 spinlock_t cmdlock; /* Protects cmd queue accesses */ 316 s32 *cmdptr; /* Pointer to the last queued cmd */ 317 318 int chi_bpf; 319 320 struct cs4215 mm; /* mmcodec special info */ 321 /* per stream (playback/record) info */ 322 struct dbri_streaminfo stream_info[DBRI_NO_STREAMS]; 323 }; 324 325 #define DBRI_MAX_VOLUME 63 /* Output volume */ 326 #define DBRI_MAX_GAIN 15 /* Input gain */ 327 328 /* DBRI Reg0 - Status Control Register - defines. (Page 17) */ 329 #define D_P (1<<15) /* Program command & queue pointer valid */ 330 #define D_G (1<<14) /* Allow 4-Word SBus Burst */ 331 #define D_S (1<<13) /* Allow 16-Word SBus Burst */ 332 #define D_E (1<<12) /* Allow 8-Word SBus Burst */ 333 #define D_X (1<<7) /* Sanity Timer Disable */ 334 #define D_T (1<<6) /* Permit activation of the TE interface */ 335 #define D_N (1<<5) /* Permit activation of the NT interface */ 336 #define D_C (1<<4) /* Permit activation of the CHI interface */ 337 #define D_F (1<<3) /* Force Sanity Timer Time-Out */ 338 #define D_D (1<<2) /* Disable Master Mode */ 339 #define D_H (1<<1) /* Halt for Analysis */ 340 #define D_R (1<<0) /* Soft Reset */ 341 342 /* DBRI Reg1 - Mode and Interrupt Register - defines. (Page 18) */ 343 #define D_LITTLE_END (1<<8) /* Byte Order */ 344 #define D_BIG_END (0<<8) /* Byte Order */ 345 #define D_MRR (1<<4) /* Multiple Error Ack on SBus (read only) */ 346 #define D_MLE (1<<3) /* Multiple Late Error on SBus (read only) */ 347 #define D_LBG (1<<2) /* Lost Bus Grant on SBus (read only) */ 348 #define D_MBE (1<<1) /* Burst Error on SBus (read only) */ 349 #define D_IR (1<<0) /* Interrupt Indicator (read only) */ 350 351 /* DBRI Reg2 - Parallel IO Register - defines. (Page 18) */ 352 #define D_ENPIO3 (1<<7) /* Enable Pin 3 */ 353 #define D_ENPIO2 (1<<6) /* Enable Pin 2 */ 354 #define D_ENPIO1 (1<<5) /* Enable Pin 1 */ 355 #define D_ENPIO0 (1<<4) /* Enable Pin 0 */ 356 #define D_ENPIO (0xf0) /* Enable all the pins */ 357 #define D_PIO3 (1<<3) /* Pin 3: 1: Data mode, 0: Ctrl mode */ 358 #define D_PIO2 (1<<2) /* Pin 2: 1: Onboard PDN */ 359 #define D_PIO1 (1<<1) /* Pin 1: 0: Reset */ 360 #define D_PIO0 (1<<0) /* Pin 0: 1: Speakerbox PDN */ 361 362 /* DBRI Commands (Page 20) */ 363 #define D_WAIT 0x0 /* Stop execution */ 364 #define D_PAUSE 0x1 /* Flush long pipes */ 365 #define D_JUMP 0x2 /* New command queue */ 366 #define D_IIQ 0x3 /* Initialize Interrupt Queue */ 367 #define D_REX 0x4 /* Report command execution via interrupt */ 368 #define D_SDP 0x5 /* Setup Data Pipe */ 369 #define D_CDP 0x6 /* Continue Data Pipe (reread NULL Pointer) */ 370 #define D_DTS 0x7 /* Define Time Slot */ 371 #define D_SSP 0x8 /* Set short Data Pipe */ 372 #define D_CHI 0x9 /* Set CHI Global Mode */ 373 #define D_NT 0xa /* NT Command */ 374 #define D_TE 0xb /* TE Command */ 375 #define D_CDEC 0xc /* Codec setup */ 376 #define D_TEST 0xd /* No comment */ 377 #define D_CDM 0xe /* CHI Data mode command */ 378 379 /* Special bits for some commands */ 380 #define D_PIPE(v) ((v)<<0) /* Pipe No.: 0-15 long, 16-21 short */ 381 382 /* Setup Data Pipe */ 383 /* IRM */ 384 #define D_SDP_2SAME (1<<18) /* Report 2nd time in a row value received */ 385 #define D_SDP_CHANGE (2<<18) /* Report any changes */ 386 #define D_SDP_EVERY (3<<18) /* Report any changes */ 387 #define D_SDP_EOL (1<<17) /* EOL interrupt enable */ 388 #define D_SDP_IDLE (1<<16) /* HDLC idle interrupt enable */ 389 390 /* Pipe data MODE */ 391 #define D_SDP_MEM (0<<13) /* To/from memory */ 392 #define D_SDP_HDLC (2<<13) 393 #define D_SDP_HDLC_D (3<<13) /* D Channel (prio control) */ 394 #define D_SDP_SER (4<<13) /* Serial to serial */ 395 #define D_SDP_FIXED (6<<13) /* Short only */ 396 #define D_SDP_MODE(v) ((v)&(7<<13)) 397 398 #define D_SDP_TO_SER (1<<12) /* Direction */ 399 #define D_SDP_FROM_SER (0<<12) /* Direction */ 400 #define D_SDP_MSB (1<<11) /* Bit order within Byte */ 401 #define D_SDP_LSB (0<<11) /* Bit order within Byte */ 402 #define D_SDP_P (1<<10) /* Pointer Valid */ 403 #define D_SDP_A (1<<8) /* Abort */ 404 #define D_SDP_C (1<<7) /* Clear */ 405 406 /* Define Time Slot */ 407 #define D_DTS_VI (1<<17) /* Valid Input Time-Slot Descriptor */ 408 #define D_DTS_VO (1<<16) /* Valid Output Time-Slot Descriptor */ 409 #define D_DTS_INS (1<<15) /* Insert Time Slot */ 410 #define D_DTS_DEL (0<<15) /* Delete Time Slot */ 411 #define D_DTS_PRVIN(v) ((v)<<10) /* Previous In Pipe */ 412 #define D_DTS_PRVOUT(v) ((v)<<5) /* Previous Out Pipe */ 413 414 /* Time Slot defines */ 415 #define D_TS_LEN(v) ((v)<<24) /* Number of bits in this time slot */ 416 #define D_TS_CYCLE(v) ((v)<<14) /* Bit Count at start of TS */ 417 #define D_TS_DI (1<<13) /* Data Invert */ 418 #define D_TS_1CHANNEL (0<<10) /* Single Channel / Normal mode */ 419 #define D_TS_MONITOR (2<<10) /* Monitor pipe */ 420 #define D_TS_NONCONTIG (3<<10) /* Non contiguous mode */ 421 #define D_TS_ANCHOR (7<<10) /* Starting short pipes */ 422 #define D_TS_MON(v) ((v)<<5) /* Monitor Pipe */ 423 #define D_TS_NEXT(v) ((v)<<0) /* Pipe no.: 0-15 long, 16-21 short */ 424 425 /* Concentration Highway Interface Modes */ 426 #define D_CHI_CHICM(v) ((v)<<16) /* Clock mode */ 427 #define D_CHI_IR (1<<15) /* Immediate Interrupt Report */ 428 #define D_CHI_EN (1<<14) /* CHIL Interrupt enabled */ 429 #define D_CHI_OD (1<<13) /* Open Drain Enable */ 430 #define D_CHI_FE (1<<12) /* Sample CHIFS on Rising Frame Edge */ 431 #define D_CHI_FD (1<<11) /* Frame Drive */ 432 #define D_CHI_BPF(v) ((v)<<0) /* Bits per Frame */ 433 434 /* NT: These are here for completeness */ 435 #define D_NT_FBIT (1<<17) /* Frame Bit */ 436 #define D_NT_NBF (1<<16) /* Number of bad frames to loose framing */ 437 #define D_NT_IRM_IMM (1<<15) /* Interrupt Report & Mask: Immediate */ 438 #define D_NT_IRM_EN (1<<14) /* Interrupt Report & Mask: Enable */ 439 #define D_NT_ISNT (1<<13) /* Configure interface as NT */ 440 #define D_NT_FT (1<<12) /* Fixed Timing */ 441 #define D_NT_EZ (1<<11) /* Echo Channel is Zeros */ 442 #define D_NT_IFA (1<<10) /* Inhibit Final Activation */ 443 #define D_NT_ACT (1<<9) /* Activate Interface */ 444 #define D_NT_MFE (1<<8) /* Multiframe Enable */ 445 #define D_NT_RLB(v) ((v)<<5) /* Remote Loopback */ 446 #define D_NT_LLB(v) ((v)<<2) /* Local Loopback */ 447 #define D_NT_FACT (1<<1) /* Force Activation */ 448 #define D_NT_ABV (1<<0) /* Activate Bipolar Violation */ 449 450 /* Codec Setup */ 451 #define D_CDEC_CK(v) ((v)<<24) /* Clock Select */ 452 #define D_CDEC_FED(v) ((v)<<12) /* FSCOD Falling Edge Delay */ 453 #define D_CDEC_RED(v) ((v)<<0) /* FSCOD Rising Edge Delay */ 454 455 /* Test */ 456 #define D_TEST_RAM(v) ((v)<<16) /* RAM Pointer */ 457 #define D_TEST_SIZE(v) ((v)<<11) /* */ 458 #define D_TEST_ROMONOFF 0x5 /* Toggle ROM opcode monitor on/off */ 459 #define D_TEST_PROC 0x6 /* Microprocessor test */ 460 #define D_TEST_SER 0x7 /* Serial-Controller test */ 461 #define D_TEST_RAMREAD 0x8 /* Copy from Ram to system memory */ 462 #define D_TEST_RAMWRITE 0x9 /* Copy into Ram from system memory */ 463 #define D_TEST_RAMBIST 0xa /* RAM Built-In Self Test */ 464 #define D_TEST_MCBIST 0xb /* Microcontroller Built-In Self Test */ 465 #define D_TEST_DUMP 0xe /* ROM Dump */ 466 467 /* CHI Data Mode */ 468 #define D_CDM_THI (1 << 8) /* Transmit Data on CHIDR Pin */ 469 #define D_CDM_RHI (1 << 7) /* Receive Data on CHIDX Pin */ 470 #define D_CDM_RCE (1 << 6) /* Receive on Rising Edge of CHICK */ 471 #define D_CDM_XCE (1 << 2) /* Transmit Data on Rising Edge of CHICK */ 472 #define D_CDM_XEN (1 << 1) /* Transmit Highway Enable */ 473 #define D_CDM_REN (1 << 0) /* Receive Highway Enable */ 474 475 /* The Interrupts */ 476 #define D_INTR_BRDY 1 /* Buffer Ready for processing */ 477 #define D_INTR_MINT 2 /* Marked Interrupt in RD/TD */ 478 #define D_INTR_IBEG 3 /* Flag to idle transition detected (HDLC) */ 479 #define D_INTR_IEND 4 /* Idle to flag transition detected (HDLC) */ 480 #define D_INTR_EOL 5 /* End of List */ 481 #define D_INTR_CMDI 6 /* Command has bean read */ 482 #define D_INTR_XCMP 8 /* Transmission of frame complete */ 483 #define D_INTR_SBRI 9 /* BRI status change info */ 484 #define D_INTR_FXDT 10 /* Fixed data change */ 485 #define D_INTR_CHIL 11 /* CHI lost frame sync (channel 36 only) */ 486 #define D_INTR_COLL 11 /* Unrecoverable D-Channel collision */ 487 #define D_INTR_DBYT 12 /* Dropped by frame slip */ 488 #define D_INTR_RBYT 13 /* Repeated by frame slip */ 489 #define D_INTR_LINT 14 /* Lost Interrupt */ 490 #define D_INTR_UNDR 15 /* DMA underrun */ 491 492 #define D_INTR_TE 32 493 #define D_INTR_NT 34 494 #define D_INTR_CHI 36 495 #define D_INTR_CMD 38 496 497 #define D_INTR_GETCHAN(v) (((v) >> 24) & 0x3f) 498 #define D_INTR_GETCODE(v) (((v) >> 20) & 0xf) 499 #define D_INTR_GETCMD(v) (((v) >> 16) & 0xf) 500 #define D_INTR_GETVAL(v) ((v) & 0xffff) 501 #define D_INTR_GETRVAL(v) ((v) & 0xfffff) 502 503 #define D_P_0 0 /* TE receive anchor */ 504 #define D_P_1 1 /* TE transmit anchor */ 505 #define D_P_2 2 /* NT transmit anchor */ 506 #define D_P_3 3 /* NT receive anchor */ 507 #define D_P_4 4 /* CHI send data */ 508 #define D_P_5 5 /* CHI receive data */ 509 #define D_P_6 6 /* */ 510 #define D_P_7 7 /* */ 511 #define D_P_8 8 /* */ 512 #define D_P_9 9 /* */ 513 #define D_P_10 10 /* */ 514 #define D_P_11 11 /* */ 515 #define D_P_12 12 /* */ 516 #define D_P_13 13 /* */ 517 #define D_P_14 14 /* */ 518 #define D_P_15 15 /* */ 519 #define D_P_16 16 /* CHI anchor pipe */ 520 #define D_P_17 17 /* CHI send */ 521 #define D_P_18 18 /* CHI receive */ 522 #define D_P_19 19 /* CHI receive */ 523 #define D_P_20 20 /* CHI receive */ 524 #define D_P_21 21 /* */ 525 #define D_P_22 22 /* */ 526 #define D_P_23 23 /* */ 527 #define D_P_24 24 /* */ 528 #define D_P_25 25 /* */ 529 #define D_P_26 26 /* */ 530 #define D_P_27 27 /* */ 531 #define D_P_28 28 /* */ 532 #define D_P_29 29 /* */ 533 #define D_P_30 30 /* */ 534 #define D_P_31 31 /* */ 535 536 /* Transmit descriptor defines */ 537 #define DBRI_TD_F (1 << 31) /* End of Frame */ 538 #define DBRI_TD_D (1 << 30) /* Do not append CRC */ 539 #define DBRI_TD_CNT(v) ((v) << 16) /* Number of valid bytes in the buffer */ 540 #define DBRI_TD_B (1 << 15) /* Final interrupt */ 541 #define DBRI_TD_M (1 << 14) /* Marker interrupt */ 542 #define DBRI_TD_I (1 << 13) /* Transmit Idle Characters */ 543 #define DBRI_TD_FCNT(v) (v) /* Flag Count */ 544 #define DBRI_TD_UNR (1 << 3) /* Underrun: transmitter is out of data */ 545 #define DBRI_TD_ABT (1 << 2) /* Abort: frame aborted */ 546 #define DBRI_TD_TBC (1 << 0) /* Transmit buffer Complete */ 547 #define DBRI_TD_STATUS(v) ((v) & 0xff) /* Transmit status */ 548 /* Maximum buffer size per TD: almost 8KB */ 549 #define DBRI_TD_MAXCNT ((1 << 13) - 4) 550 551 /* Receive descriptor defines */ 552 #define DBRI_RD_F (1 << 31) /* End of Frame */ 553 #define DBRI_RD_C (1 << 30) /* Completed buffer */ 554 #define DBRI_RD_B (1 << 15) /* Final interrupt */ 555 #define DBRI_RD_M (1 << 14) /* Marker interrupt */ 556 #define DBRI_RD_BCNT(v) (v) /* Buffer size */ 557 #define DBRI_RD_CRC (1 << 7) /* 0: CRC is correct */ 558 #define DBRI_RD_BBC (1 << 6) /* 1: Bad Byte received */ 559 #define DBRI_RD_ABT (1 << 5) /* Abort: frame aborted */ 560 #define DBRI_RD_OVRN (1 << 3) /* Overrun: data lost */ 561 #define DBRI_RD_STATUS(v) ((v) & 0xff) /* Receive status */ 562 #define DBRI_RD_CNT(v) (((v) >> 16) & 0x1fff) /* Valid bytes in the buffer */ 563 564 /* stream_info[] access */ 565 /* Translate the ALSA direction into the array index */ 566 #define DBRI_STREAMNO(substream) \ 567 (substream->stream == \ 568 SNDRV_PCM_STREAM_PLAYBACK ? DBRI_PLAY: DBRI_REC) 569 570 /* Return a pointer to dbri_streaminfo */ 571 #define DBRI_STREAM(dbri, substream) \ 572 &dbri->stream_info[DBRI_STREAMNO(substream)] 573 574 /* 575 * Short data pipes transmit LSB first. The CS4215 receives MSB first. Grrr. 576 * So we have to reverse the bits. Note: not all bit lengths are supported 577 */ 578 static __u32 reverse_bytes(__u32 b, int len) 579 { 580 switch (len) { 581 case 32: 582 b = ((b & 0xffff0000) >> 16) | ((b & 0x0000ffff) << 16); 583 /* fall through */ 584 case 16: 585 b = ((b & 0xff00ff00) >> 8) | ((b & 0x00ff00ff) << 8); 586 /* fall through */ 587 case 8: 588 b = ((b & 0xf0f0f0f0) >> 4) | ((b & 0x0f0f0f0f) << 4); 589 /* fall through */ 590 case 4: 591 b = ((b & 0xcccccccc) >> 2) | ((b & 0x33333333) << 2); 592 /* fall through */ 593 case 2: 594 b = ((b & 0xaaaaaaaa) >> 1) | ((b & 0x55555555) << 1); 595 case 1: 596 case 0: 597 break; 598 default: 599 printk(KERN_ERR "DBRI reverse_bytes: unsupported length\n"); 600 } 601 602 return b; 603 } 604 605 /* 606 **************************************************************************** 607 ************** DBRI initialization and command synchronization ************* 608 **************************************************************************** 609 610 Commands are sent to the DBRI by building a list of them in memory, 611 then writing the address of the first list item to DBRI register 8. 612 The list is terminated with a WAIT command, which generates a 613 CPU interrupt to signal completion. 614 615 Since the DBRI can run in parallel with the CPU, several means of 616 synchronization present themselves. The method implemented here uses 617 the dbri_cmdwait() to wait for execution of batch of sent commands. 618 619 A circular command buffer is used here. A new command is being added 620 while another can be executed. The scheme works by adding two WAIT commands 621 after each sent batch of commands. When the next batch is prepared it is 622 added after the WAIT commands then the WAITs are replaced with single JUMP 623 command to the new batch. The the DBRI is forced to reread the last WAIT 624 command (replaced by the JUMP by then). If the DBRI is still executing 625 previous commands the request to reread the WAIT command is ignored. 626 627 Every time a routine wants to write commands to the DBRI, it must 628 first call dbri_cmdlock() and get pointer to a free space in 629 dbri->dma->cmd buffer. After this, the commands can be written to 630 the buffer, and dbri_cmdsend() is called with the final pointer value 631 to send them to the DBRI. 632 633 */ 634 635 #define MAXLOOPS 20 636 /* 637 * Wait for the current command string to execute 638 */ 639 static void dbri_cmdwait(struct snd_dbri *dbri) 640 { 641 int maxloops = MAXLOOPS; 642 unsigned long flags; 643 644 /* Delay if previous commands are still being processed */ 645 spin_lock_irqsave(&dbri->lock, flags); 646 while ((--maxloops) > 0 && (sbus_readl(dbri->regs + REG0) & D_P)) { 647 spin_unlock_irqrestore(&dbri->lock, flags); 648 msleep_interruptible(1); 649 spin_lock_irqsave(&dbri->lock, flags); 650 } 651 spin_unlock_irqrestore(&dbri->lock, flags); 652 653 if (maxloops == 0) 654 printk(KERN_ERR "DBRI: Chip never completed command buffer\n"); 655 else 656 dprintk(D_CMD, "Chip completed command buffer (%d)\n", 657 MAXLOOPS - maxloops - 1); 658 } 659 /* 660 * Lock the command queue and return pointer to space for len cmd words 661 * It locks the cmdlock spinlock. 662 */ 663 static s32 *dbri_cmdlock(struct snd_dbri *dbri, int len) 664 { 665 u32 dvma_addr = (u32)dbri->dma_dvma; 666 667 /* Space for 2 WAIT cmds (replaced later by 1 JUMP cmd) */ 668 len += 2; 669 spin_lock(&dbri->cmdlock); 670 if (dbri->cmdptr - dbri->dma->cmd + len < DBRI_NO_CMDS - 2) 671 return dbri->cmdptr + 2; 672 else if (len < sbus_readl(dbri->regs + REG8) - dvma_addr) 673 return dbri->dma->cmd; 674 else 675 printk(KERN_ERR "DBRI: no space for commands."); 676 677 return NULL; 678 } 679 680 /* 681 * Send prepared cmd string. It works by writing a JUMP cmd into 682 * the last WAIT cmd and force DBRI to reread the cmd. 683 * The JUMP cmd points to the new cmd string. 684 * It also releases the cmdlock spinlock. 685 * 686 * Lock must be held before calling this. 687 */ 688 static void dbri_cmdsend(struct snd_dbri *dbri, s32 *cmd, int len) 689 { 690 u32 dvma_addr = (u32)dbri->dma_dvma; 691 s32 tmp, addr; 692 static int wait_id = 0; 693 694 wait_id++; 695 wait_id &= 0xffff; /* restrict it to a 16 bit counter. */ 696 *(cmd) = DBRI_CMD(D_WAIT, 1, wait_id); 697 *(cmd+1) = DBRI_CMD(D_WAIT, 1, wait_id); 698 699 /* Replace the last command with JUMP */ 700 addr = dvma_addr + (cmd - len - dbri->dma->cmd) * sizeof(s32); 701 *(dbri->cmdptr+1) = addr; 702 *(dbri->cmdptr) = DBRI_CMD(D_JUMP, 0, 0); 703 704 #ifdef DBRI_DEBUG 705 if (cmd > dbri->cmdptr) { 706 s32 *ptr; 707 708 for (ptr = dbri->cmdptr; ptr < cmd+2; ptr++) 709 dprintk(D_CMD, "cmd: %lx:%08x\n", 710 (unsigned long)ptr, *ptr); 711 } else { 712 s32 *ptr = dbri->cmdptr; 713 714 dprintk(D_CMD, "cmd: %lx:%08x\n", (unsigned long)ptr, *ptr); 715 ptr++; 716 dprintk(D_CMD, "cmd: %lx:%08x\n", (unsigned long)ptr, *ptr); 717 for (ptr = dbri->dma->cmd; ptr < cmd+2; ptr++) 718 dprintk(D_CMD, "cmd: %lx:%08x\n", 719 (unsigned long)ptr, *ptr); 720 } 721 #endif 722 723 /* Reread the last command */ 724 tmp = sbus_readl(dbri->regs + REG0); 725 tmp |= D_P; 726 sbus_writel(tmp, dbri->regs + REG0); 727 728 dbri->cmdptr = cmd; 729 spin_unlock(&dbri->cmdlock); 730 } 731 732 /* Lock must be held when calling this */ 733 static void dbri_reset(struct snd_dbri *dbri) 734 { 735 int i; 736 u32 tmp; 737 738 dprintk(D_GEN, "reset 0:%x 2:%x 8:%x 9:%x\n", 739 sbus_readl(dbri->regs + REG0), 740 sbus_readl(dbri->regs + REG2), 741 sbus_readl(dbri->regs + REG8), sbus_readl(dbri->regs + REG9)); 742 743 sbus_writel(D_R, dbri->regs + REG0); /* Soft Reset */ 744 for (i = 0; (sbus_readl(dbri->regs + REG0) & D_R) && i < 64; i++) 745 udelay(10); 746 747 /* A brute approach - DBRI falls back to working burst size by itself 748 * On SS20 D_S does not work, so do not try so high. */ 749 tmp = sbus_readl(dbri->regs + REG0); 750 tmp |= D_G | D_E; 751 tmp &= ~D_S; 752 sbus_writel(tmp, dbri->regs + REG0); 753 } 754 755 /* Lock must not be held before calling this */ 756 static void dbri_initialize(struct snd_dbri *dbri) 757 { 758 u32 dvma_addr = (u32)dbri->dma_dvma; 759 s32 *cmd; 760 u32 dma_addr; 761 unsigned long flags; 762 int n; 763 764 spin_lock_irqsave(&dbri->lock, flags); 765 766 dbri_reset(dbri); 767 768 /* Initialize pipes */ 769 for (n = 0; n < DBRI_NO_PIPES; n++) 770 dbri->pipes[n].desc = dbri->pipes[n].first_desc = -1; 771 772 spin_lock_init(&dbri->cmdlock); 773 /* 774 * Initialize the interrupt ring buffer. 775 */ 776 dma_addr = dvma_addr + dbri_dma_off(intr, 0); 777 dbri->dma->intr[0] = dma_addr; 778 dbri->dbri_irqp = 1; 779 /* 780 * Set up the interrupt queue 781 */ 782 spin_lock(&dbri->cmdlock); 783 cmd = dbri->cmdptr = dbri->dma->cmd; 784 *(cmd++) = DBRI_CMD(D_IIQ, 0, 0); 785 *(cmd++) = dma_addr; 786 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0); 787 dbri->cmdptr = cmd; 788 *(cmd++) = DBRI_CMD(D_WAIT, 1, 0); 789 *(cmd++) = DBRI_CMD(D_WAIT, 1, 0); 790 dma_addr = dvma_addr + dbri_dma_off(cmd, 0); 791 sbus_writel(dma_addr, dbri->regs + REG8); 792 spin_unlock(&dbri->cmdlock); 793 794 spin_unlock_irqrestore(&dbri->lock, flags); 795 dbri_cmdwait(dbri); 796 } 797 798 /* 799 **************************************************************************** 800 ************************** DBRI data pipe management *********************** 801 **************************************************************************** 802 803 While DBRI control functions use the command and interrupt buffers, the 804 main data path takes the form of data pipes, which can be short (command 805 and interrupt driven), or long (attached to DMA buffers). These functions 806 provide a rudimentary means of setting up and managing the DBRI's pipes, 807 but the calling functions have to make sure they respect the pipes' linked 808 list ordering, among other things. The transmit and receive functions 809 here interface closely with the transmit and receive interrupt code. 810 811 */ 812 static inline int pipe_active(struct snd_dbri *dbri, int pipe) 813 { 814 return ((pipe >= 0) && (dbri->pipes[pipe].desc != -1)); 815 } 816 817 /* reset_pipe(dbri, pipe) 818 * 819 * Called on an in-use pipe to clear anything being transmitted or received 820 * Lock must be held before calling this. 821 */ 822 static void reset_pipe(struct snd_dbri *dbri, int pipe) 823 { 824 int sdp; 825 int desc; 826 s32 *cmd; 827 828 if (pipe < 0 || pipe > DBRI_MAX_PIPE) { 829 printk(KERN_ERR "DBRI: reset_pipe called with " 830 "illegal pipe number\n"); 831 return; 832 } 833 834 sdp = dbri->pipes[pipe].sdp; 835 if (sdp == 0) { 836 printk(KERN_ERR "DBRI: reset_pipe called " 837 "on uninitialized pipe\n"); 838 return; 839 } 840 841 cmd = dbri_cmdlock(dbri, 3); 842 *(cmd++) = DBRI_CMD(D_SDP, 0, sdp | D_SDP_C | D_SDP_P); 843 *(cmd++) = 0; 844 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0); 845 dbri_cmdsend(dbri, cmd, 3); 846 847 desc = dbri->pipes[pipe].first_desc; 848 if (desc >= 0) 849 do { 850 dbri->dma->desc[desc].ba = 0; 851 dbri->dma->desc[desc].nda = 0; 852 desc = dbri->next_desc[desc]; 853 } while (desc != -1 && desc != dbri->pipes[pipe].first_desc); 854 855 dbri->pipes[pipe].desc = -1; 856 dbri->pipes[pipe].first_desc = -1; 857 } 858 859 /* 860 * Lock must be held before calling this. 861 */ 862 static void setup_pipe(struct snd_dbri *dbri, int pipe, int sdp) 863 { 864 if (pipe < 0 || pipe > DBRI_MAX_PIPE) { 865 printk(KERN_ERR "DBRI: setup_pipe called " 866 "with illegal pipe number\n"); 867 return; 868 } 869 870 if ((sdp & 0xf800) != sdp) { 871 printk(KERN_ERR "DBRI: setup_pipe called " 872 "with strange SDP value\n"); 873 /* sdp &= 0xf800; */ 874 } 875 876 /* If this is a fixed receive pipe, arrange for an interrupt 877 * every time its data changes 878 */ 879 if (D_SDP_MODE(sdp) == D_SDP_FIXED && !(sdp & D_SDP_TO_SER)) 880 sdp |= D_SDP_CHANGE; 881 882 sdp |= D_PIPE(pipe); 883 dbri->pipes[pipe].sdp = sdp; 884 dbri->pipes[pipe].desc = -1; 885 dbri->pipes[pipe].first_desc = -1; 886 887 reset_pipe(dbri, pipe); 888 } 889 890 /* 891 * Lock must be held before calling this. 892 */ 893 static void link_time_slot(struct snd_dbri *dbri, int pipe, 894 int prevpipe, int nextpipe, 895 int length, int cycle) 896 { 897 s32 *cmd; 898 int val; 899 900 if (pipe < 0 || pipe > DBRI_MAX_PIPE 901 || prevpipe < 0 || prevpipe > DBRI_MAX_PIPE 902 || nextpipe < 0 || nextpipe > DBRI_MAX_PIPE) { 903 printk(KERN_ERR 904 "DBRI: link_time_slot called with illegal pipe number\n"); 905 return; 906 } 907 908 if (dbri->pipes[pipe].sdp == 0 909 || dbri->pipes[prevpipe].sdp == 0 910 || dbri->pipes[nextpipe].sdp == 0) { 911 printk(KERN_ERR "DBRI: link_time_slot called " 912 "on uninitialized pipe\n"); 913 return; 914 } 915 916 dbri->pipes[prevpipe].nextpipe = pipe; 917 dbri->pipes[pipe].nextpipe = nextpipe; 918 dbri->pipes[pipe].length = length; 919 920 cmd = dbri_cmdlock(dbri, 4); 921 922 if (dbri->pipes[pipe].sdp & D_SDP_TO_SER) { 923 /* Deal with CHI special case: 924 * "If transmission on edges 0 or 1 is desired, then cycle n 925 * (where n = # of bit times per frame...) must be used." 926 * - DBRI data sheet, page 11 927 */ 928 if (prevpipe == 16 && cycle == 0) 929 cycle = dbri->chi_bpf; 930 931 val = D_DTS_VO | D_DTS_INS | D_DTS_PRVOUT(prevpipe) | pipe; 932 *(cmd++) = DBRI_CMD(D_DTS, 0, val); 933 *(cmd++) = 0; 934 *(cmd++) = 935 D_TS_LEN(length) | D_TS_CYCLE(cycle) | D_TS_NEXT(nextpipe); 936 } else { 937 val = D_DTS_VI | D_DTS_INS | D_DTS_PRVIN(prevpipe) | pipe; 938 *(cmd++) = DBRI_CMD(D_DTS, 0, val); 939 *(cmd++) = 940 D_TS_LEN(length) | D_TS_CYCLE(cycle) | D_TS_NEXT(nextpipe); 941 *(cmd++) = 0; 942 } 943 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0); 944 945 dbri_cmdsend(dbri, cmd, 4); 946 } 947 948 #if 0 949 /* 950 * Lock must be held before calling this. 951 */ 952 static void unlink_time_slot(struct snd_dbri *dbri, int pipe, 953 enum in_or_out direction, int prevpipe, 954 int nextpipe) 955 { 956 s32 *cmd; 957 int val; 958 959 if (pipe < 0 || pipe > DBRI_MAX_PIPE 960 || prevpipe < 0 || prevpipe > DBRI_MAX_PIPE 961 || nextpipe < 0 || nextpipe > DBRI_MAX_PIPE) { 962 printk(KERN_ERR 963 "DBRI: unlink_time_slot called with illegal pipe number\n"); 964 return; 965 } 966 967 cmd = dbri_cmdlock(dbri, 4); 968 969 if (direction == PIPEinput) { 970 val = D_DTS_VI | D_DTS_DEL | D_DTS_PRVIN(prevpipe) | pipe; 971 *(cmd++) = DBRI_CMD(D_DTS, 0, val); 972 *(cmd++) = D_TS_NEXT(nextpipe); 973 *(cmd++) = 0; 974 } else { 975 val = D_DTS_VO | D_DTS_DEL | D_DTS_PRVOUT(prevpipe) | pipe; 976 *(cmd++) = DBRI_CMD(D_DTS, 0, val); 977 *(cmd++) = 0; 978 *(cmd++) = D_TS_NEXT(nextpipe); 979 } 980 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0); 981 982 dbri_cmdsend(dbri, cmd, 4); 983 } 984 #endif 985 986 /* xmit_fixed() / recv_fixed() 987 * 988 * Transmit/receive data on a "fixed" pipe - i.e, one whose contents are not 989 * expected to change much, and which we don't need to buffer. 990 * The DBRI only interrupts us when the data changes (receive pipes), 991 * or only changes the data when this function is called (transmit pipes). 992 * Only short pipes (numbers 16-31) can be used in fixed data mode. 993 * 994 * These function operate on a 32-bit field, no matter how large 995 * the actual time slot is. The interrupt handler takes care of bit 996 * ordering and alignment. An 8-bit time slot will always end up 997 * in the low-order 8 bits, filled either MSB-first or LSB-first, 998 * depending on the settings passed to setup_pipe(). 999 * 1000 * Lock must not be held before calling it. 1001 */ 1002 static void xmit_fixed(struct snd_dbri *dbri, int pipe, unsigned int data) 1003 { 1004 s32 *cmd; 1005 unsigned long flags; 1006 1007 if (pipe < 16 || pipe > DBRI_MAX_PIPE) { 1008 printk(KERN_ERR "DBRI: xmit_fixed: Illegal pipe number\n"); 1009 return; 1010 } 1011 1012 if (D_SDP_MODE(dbri->pipes[pipe].sdp) == 0) { 1013 printk(KERN_ERR "DBRI: xmit_fixed: " 1014 "Uninitialized pipe %d\n", pipe); 1015 return; 1016 } 1017 1018 if (D_SDP_MODE(dbri->pipes[pipe].sdp) != D_SDP_FIXED) { 1019 printk(KERN_ERR "DBRI: xmit_fixed: Non-fixed pipe %d\n", pipe); 1020 return; 1021 } 1022 1023 if (!(dbri->pipes[pipe].sdp & D_SDP_TO_SER)) { 1024 printk(KERN_ERR "DBRI: xmit_fixed: Called on receive pipe %d\n", 1025 pipe); 1026 return; 1027 } 1028 1029 /* DBRI short pipes always transmit LSB first */ 1030 1031 if (dbri->pipes[pipe].sdp & D_SDP_MSB) 1032 data = reverse_bytes(data, dbri->pipes[pipe].length); 1033 1034 cmd = dbri_cmdlock(dbri, 3); 1035 1036 *(cmd++) = DBRI_CMD(D_SSP, 0, pipe); 1037 *(cmd++) = data; 1038 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0); 1039 1040 spin_lock_irqsave(&dbri->lock, flags); 1041 dbri_cmdsend(dbri, cmd, 3); 1042 spin_unlock_irqrestore(&dbri->lock, flags); 1043 dbri_cmdwait(dbri); 1044 1045 } 1046 1047 static void recv_fixed(struct snd_dbri *dbri, int pipe, volatile __u32 *ptr) 1048 { 1049 if (pipe < 16 || pipe > DBRI_MAX_PIPE) { 1050 printk(KERN_ERR "DBRI: recv_fixed called with " 1051 "illegal pipe number\n"); 1052 return; 1053 } 1054 1055 if (D_SDP_MODE(dbri->pipes[pipe].sdp) != D_SDP_FIXED) { 1056 printk(KERN_ERR "DBRI: recv_fixed called on " 1057 "non-fixed pipe %d\n", pipe); 1058 return; 1059 } 1060 1061 if (dbri->pipes[pipe].sdp & D_SDP_TO_SER) { 1062 printk(KERN_ERR "DBRI: recv_fixed called on " 1063 "transmit pipe %d\n", pipe); 1064 return; 1065 } 1066 1067 dbri->pipes[pipe].recv_fixed_ptr = ptr; 1068 } 1069 1070 /* setup_descs() 1071 * 1072 * Setup transmit/receive data on a "long" pipe - i.e, one associated 1073 * with a DMA buffer. 1074 * 1075 * Only pipe numbers 0-15 can be used in this mode. 1076 * 1077 * This function takes a stream number pointing to a data buffer, 1078 * and work by building chains of descriptors which identify the 1079 * data buffers. Buffers too large for a single descriptor will 1080 * be spread across multiple descriptors. 1081 * 1082 * All descriptors create a ring buffer. 1083 * 1084 * Lock must be held before calling this. 1085 */ 1086 static int setup_descs(struct snd_dbri *dbri, int streamno, unsigned int period) 1087 { 1088 struct dbri_streaminfo *info = &dbri->stream_info[streamno]; 1089 u32 dvma_addr = (u32)dbri->dma_dvma; 1090 __u32 dvma_buffer; 1091 int desc; 1092 int len; 1093 int first_desc = -1; 1094 int last_desc = -1; 1095 1096 if (info->pipe < 0 || info->pipe > 15) { 1097 printk(KERN_ERR "DBRI: setup_descs: Illegal pipe number\n"); 1098 return -2; 1099 } 1100 1101 if (dbri->pipes[info->pipe].sdp == 0) { 1102 printk(KERN_ERR "DBRI: setup_descs: Uninitialized pipe %d\n", 1103 info->pipe); 1104 return -2; 1105 } 1106 1107 dvma_buffer = info->dvma_buffer; 1108 len = info->size; 1109 1110 if (streamno == DBRI_PLAY) { 1111 if (!(dbri->pipes[info->pipe].sdp & D_SDP_TO_SER)) { 1112 printk(KERN_ERR "DBRI: setup_descs: " 1113 "Called on receive pipe %d\n", info->pipe); 1114 return -2; 1115 } 1116 } else { 1117 if (dbri->pipes[info->pipe].sdp & D_SDP_TO_SER) { 1118 printk(KERN_ERR 1119 "DBRI: setup_descs: Called on transmit pipe %d\n", 1120 info->pipe); 1121 return -2; 1122 } 1123 /* Should be able to queue multiple buffers 1124 * to receive on a pipe 1125 */ 1126 if (pipe_active(dbri, info->pipe)) { 1127 printk(KERN_ERR "DBRI: recv_on_pipe: " 1128 "Called on active pipe %d\n", info->pipe); 1129 return -2; 1130 } 1131 1132 /* Make sure buffer size is multiple of four */ 1133 len &= ~3; 1134 } 1135 1136 /* Free descriptors if pipe has any */ 1137 desc = dbri->pipes[info->pipe].first_desc; 1138 if (desc >= 0) 1139 do { 1140 dbri->dma->desc[desc].ba = 0; 1141 dbri->dma->desc[desc].nda = 0; 1142 desc = dbri->next_desc[desc]; 1143 } while (desc != -1 && 1144 desc != dbri->pipes[info->pipe].first_desc); 1145 1146 dbri->pipes[info->pipe].desc = -1; 1147 dbri->pipes[info->pipe].first_desc = -1; 1148 1149 desc = 0; 1150 while (len > 0) { 1151 int mylen; 1152 1153 for (; desc < DBRI_NO_DESCS; desc++) { 1154 if (!dbri->dma->desc[desc].ba) 1155 break; 1156 } 1157 1158 if (desc == DBRI_NO_DESCS) { 1159 printk(KERN_ERR "DBRI: setup_descs: No descriptors\n"); 1160 return -1; 1161 } 1162 1163 if (len > DBRI_TD_MAXCNT) 1164 mylen = DBRI_TD_MAXCNT; /* 8KB - 4 */ 1165 else 1166 mylen = len; 1167 1168 if (mylen > period) 1169 mylen = period; 1170 1171 dbri->next_desc[desc] = -1; 1172 dbri->dma->desc[desc].ba = dvma_buffer; 1173 dbri->dma->desc[desc].nda = 0; 1174 1175 if (streamno == DBRI_PLAY) { 1176 dbri->dma->desc[desc].word1 = DBRI_TD_CNT(mylen); 1177 dbri->dma->desc[desc].word4 = 0; 1178 dbri->dma->desc[desc].word1 |= DBRI_TD_F | DBRI_TD_B; 1179 } else { 1180 dbri->dma->desc[desc].word1 = 0; 1181 dbri->dma->desc[desc].word4 = 1182 DBRI_RD_B | DBRI_RD_BCNT(mylen); 1183 } 1184 1185 if (first_desc == -1) 1186 first_desc = desc; 1187 else { 1188 dbri->next_desc[last_desc] = desc; 1189 dbri->dma->desc[last_desc].nda = 1190 dvma_addr + dbri_dma_off(desc, desc); 1191 } 1192 1193 last_desc = desc; 1194 dvma_buffer += mylen; 1195 len -= mylen; 1196 } 1197 1198 if (first_desc == -1 || last_desc == -1) { 1199 printk(KERN_ERR "DBRI: setup_descs: " 1200 " Not enough descriptors available\n"); 1201 return -1; 1202 } 1203 1204 dbri->dma->desc[last_desc].nda = 1205 dvma_addr + dbri_dma_off(desc, first_desc); 1206 dbri->next_desc[last_desc] = first_desc; 1207 dbri->pipes[info->pipe].first_desc = first_desc; 1208 dbri->pipes[info->pipe].desc = first_desc; 1209 1210 #ifdef DBRI_DEBUG 1211 for (desc = first_desc; desc != -1;) { 1212 dprintk(D_DESC, "DESC %d: %08x %08x %08x %08x\n", 1213 desc, 1214 dbri->dma->desc[desc].word1, 1215 dbri->dma->desc[desc].ba, 1216 dbri->dma->desc[desc].nda, dbri->dma->desc[desc].word4); 1217 desc = dbri->next_desc[desc]; 1218 if (desc == first_desc) 1219 break; 1220 } 1221 #endif 1222 return 0; 1223 } 1224 1225 /* 1226 **************************************************************************** 1227 ************************** DBRI - CHI interface **************************** 1228 **************************************************************************** 1229 1230 The CHI is a four-wire (clock, frame sync, data in, data out) time-division 1231 multiplexed serial interface which the DBRI can operate in either master 1232 (give clock/frame sync) or slave (take clock/frame sync) mode. 1233 1234 */ 1235 1236 enum master_or_slave { CHImaster, CHIslave }; 1237 1238 /* 1239 * Lock must not be held before calling it. 1240 */ 1241 static void reset_chi(struct snd_dbri *dbri, 1242 enum master_or_slave master_or_slave, 1243 int bits_per_frame) 1244 { 1245 s32 *cmd; 1246 int val; 1247 1248 /* Set CHI Anchor: Pipe 16 */ 1249 1250 cmd = dbri_cmdlock(dbri, 4); 1251 val = D_DTS_VO | D_DTS_VI | D_DTS_INS 1252 | D_DTS_PRVIN(16) | D_PIPE(16) | D_DTS_PRVOUT(16); 1253 *(cmd++) = DBRI_CMD(D_DTS, 0, val); 1254 *(cmd++) = D_TS_ANCHOR | D_TS_NEXT(16); 1255 *(cmd++) = D_TS_ANCHOR | D_TS_NEXT(16); 1256 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0); 1257 dbri_cmdsend(dbri, cmd, 4); 1258 1259 dbri->pipes[16].sdp = 1; 1260 dbri->pipes[16].nextpipe = 16; 1261 1262 cmd = dbri_cmdlock(dbri, 4); 1263 1264 if (master_or_slave == CHIslave) { 1265 /* Setup DBRI for CHI Slave - receive clock, frame sync (FS) 1266 * 1267 * CHICM = 0 (slave mode, 8 kHz frame rate) 1268 * IR = give immediate CHI status interrupt 1269 * EN = give CHI status interrupt upon change 1270 */ 1271 *(cmd++) = DBRI_CMD(D_CHI, 0, D_CHI_CHICM(0)); 1272 } else { 1273 /* Setup DBRI for CHI Master - generate clock, FS 1274 * 1275 * BPF = bits per 8 kHz frame 1276 * 12.288 MHz / CHICM_divisor = clock rate 1277 * FD = 1 - drive CHIFS on rising edge of CHICK 1278 */ 1279 int clockrate = bits_per_frame * 8; 1280 int divisor = 12288 / clockrate; 1281 1282 if (divisor > 255 || divisor * clockrate != 12288) 1283 printk(KERN_ERR "DBRI: illegal bits_per_frame " 1284 "in setup_chi\n"); 1285 1286 *(cmd++) = DBRI_CMD(D_CHI, 0, D_CHI_CHICM(divisor) | D_CHI_FD 1287 | D_CHI_BPF(bits_per_frame)); 1288 } 1289 1290 dbri->chi_bpf = bits_per_frame; 1291 1292 /* CHI Data Mode 1293 * 1294 * RCE = 0 - receive on falling edge of CHICK 1295 * XCE = 1 - transmit on rising edge of CHICK 1296 * XEN = 1 - enable transmitter 1297 * REN = 1 - enable receiver 1298 */ 1299 1300 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0); 1301 *(cmd++) = DBRI_CMD(D_CDM, 0, D_CDM_XCE | D_CDM_XEN | D_CDM_REN); 1302 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0); 1303 1304 dbri_cmdsend(dbri, cmd, 4); 1305 } 1306 1307 /* 1308 **************************************************************************** 1309 *********************** CS4215 audio codec management ********************** 1310 **************************************************************************** 1311 1312 In the standard SPARC audio configuration, the CS4215 codec is attached 1313 to the DBRI via the CHI interface and few of the DBRI's PIO pins. 1314 1315 * Lock must not be held before calling it. 1316 1317 */ 1318 static void cs4215_setup_pipes(struct snd_dbri *dbri) 1319 { 1320 unsigned long flags; 1321 1322 spin_lock_irqsave(&dbri->lock, flags); 1323 /* 1324 * Data mode: 1325 * Pipe 4: Send timeslots 1-4 (audio data) 1326 * Pipe 20: Send timeslots 5-8 (part of ctrl data) 1327 * Pipe 6: Receive timeslots 1-4 (audio data) 1328 * Pipe 21: Receive timeslots 6-7. We can only receive 20 bits via 1329 * interrupt, and the rest of the data (slot 5 and 8) is 1330 * not relevant for us (only for doublechecking). 1331 * 1332 * Control mode: 1333 * Pipe 17: Send timeslots 1-4 (slots 5-8 are read only) 1334 * Pipe 18: Receive timeslot 1 (clb). 1335 * Pipe 19: Receive timeslot 7 (version). 1336 */ 1337 1338 setup_pipe(dbri, 4, D_SDP_MEM | D_SDP_TO_SER | D_SDP_MSB); 1339 setup_pipe(dbri, 20, D_SDP_FIXED | D_SDP_TO_SER | D_SDP_MSB); 1340 setup_pipe(dbri, 6, D_SDP_MEM | D_SDP_FROM_SER | D_SDP_MSB); 1341 setup_pipe(dbri, 21, D_SDP_FIXED | D_SDP_FROM_SER | D_SDP_MSB); 1342 1343 setup_pipe(dbri, 17, D_SDP_FIXED | D_SDP_TO_SER | D_SDP_MSB); 1344 setup_pipe(dbri, 18, D_SDP_FIXED | D_SDP_FROM_SER | D_SDP_MSB); 1345 setup_pipe(dbri, 19, D_SDP_FIXED | D_SDP_FROM_SER | D_SDP_MSB); 1346 spin_unlock_irqrestore(&dbri->lock, flags); 1347 1348 dbri_cmdwait(dbri); 1349 } 1350 1351 static int cs4215_init_data(struct cs4215 *mm) 1352 { 1353 /* 1354 * No action, memory resetting only. 1355 * 1356 * Data Time Slot 5-8 1357 * Speaker,Line and Headphone enable. Gain set to the half. 1358 * Input is mike. 1359 */ 1360 mm->data[0] = CS4215_LO(0x20) | CS4215_HE | CS4215_LE; 1361 mm->data[1] = CS4215_RO(0x20) | CS4215_SE; 1362 mm->data[2] = CS4215_LG(0x8) | CS4215_IS | CS4215_PIO0 | CS4215_PIO1; 1363 mm->data[3] = CS4215_RG(0x8) | CS4215_MA(0xf); 1364 1365 /* 1366 * Control Time Slot 1-4 1367 * 0: Default I/O voltage scale 1368 * 1: 8 bit ulaw, 8kHz, mono, high pass filter disabled 1369 * 2: Serial enable, CHI master, 128 bits per frame, clock 1 1370 * 3: Tests disabled 1371 */ 1372 mm->ctrl[0] = CS4215_RSRVD_1 | CS4215_MLB; 1373 mm->ctrl[1] = CS4215_DFR_ULAW | CS4215_FREQ[0].csval; 1374 mm->ctrl[2] = CS4215_XCLK | CS4215_BSEL_128 | CS4215_FREQ[0].xtal; 1375 mm->ctrl[3] = 0; 1376 1377 mm->status = 0; 1378 mm->version = 0xff; 1379 mm->precision = 8; /* For ULAW */ 1380 mm->channels = 1; 1381 1382 return 0; 1383 } 1384 1385 static void cs4215_setdata(struct snd_dbri *dbri, int muted) 1386 { 1387 if (muted) { 1388 dbri->mm.data[0] |= 63; 1389 dbri->mm.data[1] |= 63; 1390 dbri->mm.data[2] &= ~15; 1391 dbri->mm.data[3] &= ~15; 1392 } else { 1393 /* Start by setting the playback attenuation. */ 1394 struct dbri_streaminfo *info = &dbri->stream_info[DBRI_PLAY]; 1395 int left_gain = info->left_gain & 0x3f; 1396 int right_gain = info->right_gain & 0x3f; 1397 1398 dbri->mm.data[0] &= ~0x3f; /* Reset the volume bits */ 1399 dbri->mm.data[1] &= ~0x3f; 1400 dbri->mm.data[0] |= (DBRI_MAX_VOLUME - left_gain); 1401 dbri->mm.data[1] |= (DBRI_MAX_VOLUME - right_gain); 1402 1403 /* Now set the recording gain. */ 1404 info = &dbri->stream_info[DBRI_REC]; 1405 left_gain = info->left_gain & 0xf; 1406 right_gain = info->right_gain & 0xf; 1407 dbri->mm.data[2] |= CS4215_LG(left_gain); 1408 dbri->mm.data[3] |= CS4215_RG(right_gain); 1409 } 1410 1411 xmit_fixed(dbri, 20, *(int *)dbri->mm.data); 1412 } 1413 1414 /* 1415 * Set the CS4215 to data mode. 1416 */ 1417 static void cs4215_open(struct snd_dbri *dbri) 1418 { 1419 int data_width; 1420 u32 tmp; 1421 unsigned long flags; 1422 1423 dprintk(D_MM, "cs4215_open: %d channels, %d bits\n", 1424 dbri->mm.channels, dbri->mm.precision); 1425 1426 /* Temporarily mute outputs, and wait 1/8000 sec (125 us) 1427 * to make sure this takes. This avoids clicking noises. 1428 */ 1429 1430 cs4215_setdata(dbri, 1); 1431 udelay(125); 1432 1433 /* 1434 * Data mode: 1435 * Pipe 4: Send timeslots 1-4 (audio data) 1436 * Pipe 20: Send timeslots 5-8 (part of ctrl data) 1437 * Pipe 6: Receive timeslots 1-4 (audio data) 1438 * Pipe 21: Receive timeslots 6-7. We can only receive 20 bits via 1439 * interrupt, and the rest of the data (slot 5 and 8) is 1440 * not relevant for us (only for doublechecking). 1441 * 1442 * Just like in control mode, the time slots are all offset by eight 1443 * bits. The CS4215, it seems, observes TSIN (the delayed signal) 1444 * even if it's the CHI master. Don't ask me... 1445 */ 1446 spin_lock_irqsave(&dbri->lock, flags); 1447 tmp = sbus_readl(dbri->regs + REG0); 1448 tmp &= ~(D_C); /* Disable CHI */ 1449 sbus_writel(tmp, dbri->regs + REG0); 1450 1451 /* Switch CS4215 to data mode - set PIO3 to 1 */ 1452 sbus_writel(D_ENPIO | D_PIO1 | D_PIO3 | 1453 (dbri->mm.onboard ? D_PIO0 : D_PIO2), dbri->regs + REG2); 1454 1455 reset_chi(dbri, CHIslave, 128); 1456 1457 /* Note: this next doesn't work for 8-bit stereo, because the two 1458 * channels would be on timeslots 1 and 3, with 2 and 4 idle. 1459 * (See CS4215 datasheet Fig 15) 1460 * 1461 * DBRI non-contiguous mode would be required to make this work. 1462 */ 1463 data_width = dbri->mm.channels * dbri->mm.precision; 1464 1465 link_time_slot(dbri, 4, 16, 16, data_width, dbri->mm.offset); 1466 link_time_slot(dbri, 20, 4, 16, 32, dbri->mm.offset + 32); 1467 link_time_slot(dbri, 6, 16, 16, data_width, dbri->mm.offset); 1468 link_time_slot(dbri, 21, 6, 16, 16, dbri->mm.offset + 40); 1469 1470 /* FIXME: enable CHI after _setdata? */ 1471 tmp = sbus_readl(dbri->regs + REG0); 1472 tmp |= D_C; /* Enable CHI */ 1473 sbus_writel(tmp, dbri->regs + REG0); 1474 spin_unlock_irqrestore(&dbri->lock, flags); 1475 1476 cs4215_setdata(dbri, 0); 1477 } 1478 1479 /* 1480 * Send the control information (i.e. audio format) 1481 */ 1482 static int cs4215_setctrl(struct snd_dbri *dbri) 1483 { 1484 int i, val; 1485 u32 tmp; 1486 unsigned long flags; 1487 1488 /* FIXME - let the CPU do something useful during these delays */ 1489 1490 /* Temporarily mute outputs, and wait 1/8000 sec (125 us) 1491 * to make sure this takes. This avoids clicking noises. 1492 */ 1493 cs4215_setdata(dbri, 1); 1494 udelay(125); 1495 1496 /* 1497 * Enable Control mode: Set DBRI's PIO3 (4215's D/~C) to 0, then wait 1498 * 12 cycles <= 12/(5512.5*64) sec = 34.01 usec 1499 */ 1500 val = D_ENPIO | D_PIO1 | (dbri->mm.onboard ? D_PIO0 : D_PIO2); 1501 sbus_writel(val, dbri->regs + REG2); 1502 dprintk(D_MM, "cs4215_setctrl: reg2=0x%x\n", val); 1503 udelay(34); 1504 1505 /* In Control mode, the CS4215 is a slave device, so the DBRI must 1506 * operate as CHI master, supplying clocking and frame synchronization. 1507 * 1508 * In Data mode, however, the CS4215 must be CHI master to insure 1509 * that its data stream is synchronous with its codec. 1510 * 1511 * The upshot of all this? We start by putting the DBRI into master 1512 * mode, program the CS4215 in Control mode, then switch the CS4215 1513 * into Data mode and put the DBRI into slave mode. Various timing 1514 * requirements must be observed along the way. 1515 * 1516 * Oh, and one more thing, on a SPARCStation 20 (and maybe 1517 * others?), the addressing of the CS4215's time slots is 1518 * offset by eight bits, so we add eight to all the "cycle" 1519 * values in the Define Time Slot (DTS) commands. This is 1520 * done in hardware by a TI 248 that delays the DBRI->4215 1521 * frame sync signal by eight clock cycles. Anybody know why? 1522 */ 1523 spin_lock_irqsave(&dbri->lock, flags); 1524 tmp = sbus_readl(dbri->regs + REG0); 1525 tmp &= ~D_C; /* Disable CHI */ 1526 sbus_writel(tmp, dbri->regs + REG0); 1527 1528 reset_chi(dbri, CHImaster, 128); 1529 1530 /* 1531 * Control mode: 1532 * Pipe 17: Send timeslots 1-4 (slots 5-8 are read only) 1533 * Pipe 18: Receive timeslot 1 (clb). 1534 * Pipe 19: Receive timeslot 7 (version). 1535 */ 1536 1537 link_time_slot(dbri, 17, 16, 16, 32, dbri->mm.offset); 1538 link_time_slot(dbri, 18, 16, 16, 8, dbri->mm.offset); 1539 link_time_slot(dbri, 19, 18, 16, 8, dbri->mm.offset + 48); 1540 spin_unlock_irqrestore(&dbri->lock, flags); 1541 1542 /* Wait for the chip to echo back CLB (Control Latch Bit) as zero */ 1543 dbri->mm.ctrl[0] &= ~CS4215_CLB; 1544 xmit_fixed(dbri, 17, *(int *)dbri->mm.ctrl); 1545 1546 spin_lock_irqsave(&dbri->lock, flags); 1547 tmp = sbus_readl(dbri->regs + REG0); 1548 tmp |= D_C; /* Enable CHI */ 1549 sbus_writel(tmp, dbri->regs + REG0); 1550 spin_unlock_irqrestore(&dbri->lock, flags); 1551 1552 for (i = 10; ((dbri->mm.status & 0xe4) != 0x20); --i) 1553 msleep_interruptible(1); 1554 1555 if (i == 0) { 1556 dprintk(D_MM, "CS4215 didn't respond to CLB (0x%02x)\n", 1557 dbri->mm.status); 1558 return -1; 1559 } 1560 1561 /* Disable changes to our copy of the version number, as we are about 1562 * to leave control mode. 1563 */ 1564 recv_fixed(dbri, 19, NULL); 1565 1566 /* Terminate CS4215 control mode - data sheet says 1567 * "Set CLB=1 and send two more frames of valid control info" 1568 */ 1569 dbri->mm.ctrl[0] |= CS4215_CLB; 1570 xmit_fixed(dbri, 17, *(int *)dbri->mm.ctrl); 1571 1572 /* Two frames of control info @ 8kHz frame rate = 250 us delay */ 1573 udelay(250); 1574 1575 cs4215_setdata(dbri, 0); 1576 1577 return 0; 1578 } 1579 1580 /* 1581 * Setup the codec with the sampling rate, audio format and number of 1582 * channels. 1583 * As part of the process we resend the settings for the data 1584 * timeslots as well. 1585 */ 1586 static int cs4215_prepare(struct snd_dbri *dbri, unsigned int rate, 1587 snd_pcm_format_t format, unsigned int channels) 1588 { 1589 int freq_idx; 1590 int ret = 0; 1591 1592 /* Lookup index for this rate */ 1593 for (freq_idx = 0; CS4215_FREQ[freq_idx].freq != 0; freq_idx++) { 1594 if (CS4215_FREQ[freq_idx].freq == rate) 1595 break; 1596 } 1597 if (CS4215_FREQ[freq_idx].freq != rate) { 1598 printk(KERN_WARNING "DBRI: Unsupported rate %d Hz\n", rate); 1599 return -1; 1600 } 1601 1602 switch (format) { 1603 case SNDRV_PCM_FORMAT_MU_LAW: 1604 dbri->mm.ctrl[1] = CS4215_DFR_ULAW; 1605 dbri->mm.precision = 8; 1606 break; 1607 case SNDRV_PCM_FORMAT_A_LAW: 1608 dbri->mm.ctrl[1] = CS4215_DFR_ALAW; 1609 dbri->mm.precision = 8; 1610 break; 1611 case SNDRV_PCM_FORMAT_U8: 1612 dbri->mm.ctrl[1] = CS4215_DFR_LINEAR8; 1613 dbri->mm.precision = 8; 1614 break; 1615 case SNDRV_PCM_FORMAT_S16_BE: 1616 dbri->mm.ctrl[1] = CS4215_DFR_LINEAR16; 1617 dbri->mm.precision = 16; 1618 break; 1619 default: 1620 printk(KERN_WARNING "DBRI: Unsupported format %d\n", format); 1621 return -1; 1622 } 1623 1624 /* Add rate parameters */ 1625 dbri->mm.ctrl[1] |= CS4215_FREQ[freq_idx].csval; 1626 dbri->mm.ctrl[2] = CS4215_XCLK | 1627 CS4215_BSEL_128 | CS4215_FREQ[freq_idx].xtal; 1628 1629 dbri->mm.channels = channels; 1630 if (channels == 2) 1631 dbri->mm.ctrl[1] |= CS4215_DFR_STEREO; 1632 1633 ret = cs4215_setctrl(dbri); 1634 if (ret == 0) 1635 cs4215_open(dbri); /* set codec to data mode */ 1636 1637 return ret; 1638 } 1639 1640 /* 1641 * 1642 */ 1643 static int cs4215_init(struct snd_dbri *dbri) 1644 { 1645 u32 reg2 = sbus_readl(dbri->regs + REG2); 1646 dprintk(D_MM, "cs4215_init: reg2=0x%x\n", reg2); 1647 1648 /* Look for the cs4215 chips */ 1649 if (reg2 & D_PIO2) { 1650 dprintk(D_MM, "Onboard CS4215 detected\n"); 1651 dbri->mm.onboard = 1; 1652 } 1653 if (reg2 & D_PIO0) { 1654 dprintk(D_MM, "Speakerbox detected\n"); 1655 dbri->mm.onboard = 0; 1656 1657 if (reg2 & D_PIO2) { 1658 printk(KERN_INFO "DBRI: Using speakerbox / " 1659 "ignoring onboard mmcodec.\n"); 1660 sbus_writel(D_ENPIO2, dbri->regs + REG2); 1661 } 1662 } 1663 1664 if (!(reg2 & (D_PIO0 | D_PIO2))) { 1665 printk(KERN_ERR "DBRI: no mmcodec found.\n"); 1666 return -EIO; 1667 } 1668 1669 cs4215_setup_pipes(dbri); 1670 cs4215_init_data(&dbri->mm); 1671 1672 /* Enable capture of the status & version timeslots. */ 1673 recv_fixed(dbri, 18, &dbri->mm.status); 1674 recv_fixed(dbri, 19, &dbri->mm.version); 1675 1676 dbri->mm.offset = dbri->mm.onboard ? 0 : 8; 1677 if (cs4215_setctrl(dbri) == -1 || dbri->mm.version == 0xff) { 1678 dprintk(D_MM, "CS4215 failed probe at offset %d\n", 1679 dbri->mm.offset); 1680 return -EIO; 1681 } 1682 dprintk(D_MM, "Found CS4215 at offset %d\n", dbri->mm.offset); 1683 1684 return 0; 1685 } 1686 1687 /* 1688 **************************************************************************** 1689 *************************** DBRI interrupt handler ************************* 1690 **************************************************************************** 1691 1692 The DBRI communicates with the CPU mainly via a circular interrupt 1693 buffer. When an interrupt is signaled, the CPU walks through the 1694 buffer and calls dbri_process_one_interrupt() for each interrupt word. 1695 Complicated interrupts are handled by dedicated functions (which 1696 appear first in this file). Any pending interrupts can be serviced by 1697 calling dbri_process_interrupt_buffer(), which works even if the CPU's 1698 interrupts are disabled. 1699 1700 */ 1701 1702 /* xmit_descs() 1703 * 1704 * Starts transmitting the current TD's for recording/playing. 1705 * For playback, ALSA has filled the DMA memory with new data (we hope). 1706 */ 1707 static void xmit_descs(struct snd_dbri *dbri) 1708 { 1709 struct dbri_streaminfo *info; 1710 u32 dvma_addr; 1711 s32 *cmd; 1712 unsigned long flags; 1713 int first_td; 1714 1715 if (dbri == NULL) 1716 return; /* Disabled */ 1717 1718 dvma_addr = (u32)dbri->dma_dvma; 1719 info = &dbri->stream_info[DBRI_REC]; 1720 spin_lock_irqsave(&dbri->lock, flags); 1721 1722 if (info->pipe >= 0) { 1723 first_td = dbri->pipes[info->pipe].first_desc; 1724 1725 dprintk(D_DESC, "xmit_descs rec @ TD %d\n", first_td); 1726 1727 /* Stream could be closed by the time we run. */ 1728 if (first_td >= 0) { 1729 cmd = dbri_cmdlock(dbri, 2); 1730 *(cmd++) = DBRI_CMD(D_SDP, 0, 1731 dbri->pipes[info->pipe].sdp 1732 | D_SDP_P | D_SDP_EVERY | D_SDP_C); 1733 *(cmd++) = dvma_addr + 1734 dbri_dma_off(desc, first_td); 1735 dbri_cmdsend(dbri, cmd, 2); 1736 1737 /* Reset our admin of the pipe. */ 1738 dbri->pipes[info->pipe].desc = first_td; 1739 } 1740 } 1741 1742 info = &dbri->stream_info[DBRI_PLAY]; 1743 1744 if (info->pipe >= 0) { 1745 first_td = dbri->pipes[info->pipe].first_desc; 1746 1747 dprintk(D_DESC, "xmit_descs play @ TD %d\n", first_td); 1748 1749 /* Stream could be closed by the time we run. */ 1750 if (first_td >= 0) { 1751 cmd = dbri_cmdlock(dbri, 2); 1752 *(cmd++) = DBRI_CMD(D_SDP, 0, 1753 dbri->pipes[info->pipe].sdp 1754 | D_SDP_P | D_SDP_EVERY | D_SDP_C); 1755 *(cmd++) = dvma_addr + 1756 dbri_dma_off(desc, first_td); 1757 dbri_cmdsend(dbri, cmd, 2); 1758 1759 /* Reset our admin of the pipe. */ 1760 dbri->pipes[info->pipe].desc = first_td; 1761 } 1762 } 1763 1764 spin_unlock_irqrestore(&dbri->lock, flags); 1765 } 1766 1767 /* transmission_complete_intr() 1768 * 1769 * Called by main interrupt handler when DBRI signals transmission complete 1770 * on a pipe (interrupt triggered by the B bit in a transmit descriptor). 1771 * 1772 * Walks through the pipe's list of transmit buffer descriptors and marks 1773 * them as available. Stops when the first descriptor is found without 1774 * TBC (Transmit Buffer Complete) set, or we've run through them all. 1775 * 1776 * The DMA buffers are not released. They form a ring buffer and 1777 * they are filled by ALSA while others are transmitted by DMA. 1778 * 1779 */ 1780 1781 static void transmission_complete_intr(struct snd_dbri *dbri, int pipe) 1782 { 1783 struct dbri_streaminfo *info = &dbri->stream_info[DBRI_PLAY]; 1784 int td = dbri->pipes[pipe].desc; 1785 int status; 1786 1787 while (td >= 0) { 1788 if (td >= DBRI_NO_DESCS) { 1789 printk(KERN_ERR "DBRI: invalid td on pipe %d\n", pipe); 1790 return; 1791 } 1792 1793 status = DBRI_TD_STATUS(dbri->dma->desc[td].word4); 1794 if (!(status & DBRI_TD_TBC)) 1795 break; 1796 1797 dprintk(D_INT, "TD %d, status 0x%02x\n", td, status); 1798 1799 dbri->dma->desc[td].word4 = 0; /* Reset it for next time. */ 1800 info->offset += DBRI_RD_CNT(dbri->dma->desc[td].word1); 1801 1802 td = dbri->next_desc[td]; 1803 dbri->pipes[pipe].desc = td; 1804 } 1805 1806 /* Notify ALSA */ 1807 spin_unlock(&dbri->lock); 1808 snd_pcm_period_elapsed(info->substream); 1809 spin_lock(&dbri->lock); 1810 } 1811 1812 static void reception_complete_intr(struct snd_dbri *dbri, int pipe) 1813 { 1814 struct dbri_streaminfo *info; 1815 int rd = dbri->pipes[pipe].desc; 1816 s32 status; 1817 1818 if (rd < 0 || rd >= DBRI_NO_DESCS) { 1819 printk(KERN_ERR "DBRI: invalid rd on pipe %d\n", pipe); 1820 return; 1821 } 1822 1823 dbri->pipes[pipe].desc = dbri->next_desc[rd]; 1824 status = dbri->dma->desc[rd].word1; 1825 dbri->dma->desc[rd].word1 = 0; /* Reset it for next time. */ 1826 1827 info = &dbri->stream_info[DBRI_REC]; 1828 info->offset += DBRI_RD_CNT(status); 1829 1830 /* FIXME: Check status */ 1831 1832 dprintk(D_INT, "Recv RD %d, status 0x%02x, len %d\n", 1833 rd, DBRI_RD_STATUS(status), DBRI_RD_CNT(status)); 1834 1835 /* Notify ALSA */ 1836 spin_unlock(&dbri->lock); 1837 snd_pcm_period_elapsed(info->substream); 1838 spin_lock(&dbri->lock); 1839 } 1840 1841 static void dbri_process_one_interrupt(struct snd_dbri *dbri, int x) 1842 { 1843 int val = D_INTR_GETVAL(x); 1844 int channel = D_INTR_GETCHAN(x); 1845 int command = D_INTR_GETCMD(x); 1846 int code = D_INTR_GETCODE(x); 1847 #ifdef DBRI_DEBUG 1848 int rval = D_INTR_GETRVAL(x); 1849 #endif 1850 1851 if (channel == D_INTR_CMD) { 1852 dprintk(D_CMD, "INTR: Command: %-5s Value:%d\n", 1853 cmds[command], val); 1854 } else { 1855 dprintk(D_INT, "INTR: Chan:%d Code:%d Val:%#x\n", 1856 channel, code, rval); 1857 } 1858 1859 switch (code) { 1860 case D_INTR_CMDI: 1861 if (command != D_WAIT) 1862 printk(KERN_ERR "DBRI: Command read interrupt\n"); 1863 break; 1864 case D_INTR_BRDY: 1865 reception_complete_intr(dbri, channel); 1866 break; 1867 case D_INTR_XCMP: 1868 case D_INTR_MINT: 1869 transmission_complete_intr(dbri, channel); 1870 break; 1871 case D_INTR_UNDR: 1872 /* UNDR - Transmission underrun 1873 * resend SDP command with clear pipe bit (C) set 1874 */ 1875 { 1876 /* FIXME: do something useful in case of underrun */ 1877 printk(KERN_ERR "DBRI: Underrun error\n"); 1878 #if 0 1879 s32 *cmd; 1880 int pipe = channel; 1881 int td = dbri->pipes[pipe].desc; 1882 1883 dbri->dma->desc[td].word4 = 0; 1884 cmd = dbri_cmdlock(dbri, NoGetLock); 1885 *(cmd++) = DBRI_CMD(D_SDP, 0, 1886 dbri->pipes[pipe].sdp 1887 | D_SDP_P | D_SDP_C | D_SDP_2SAME); 1888 *(cmd++) = dbri->dma_dvma + dbri_dma_off(desc, td); 1889 dbri_cmdsend(dbri, cmd); 1890 #endif 1891 } 1892 break; 1893 case D_INTR_FXDT: 1894 /* FXDT - Fixed data change */ 1895 if (dbri->pipes[channel].sdp & D_SDP_MSB) 1896 val = reverse_bytes(val, dbri->pipes[channel].length); 1897 1898 if (dbri->pipes[channel].recv_fixed_ptr) 1899 *(dbri->pipes[channel].recv_fixed_ptr) = val; 1900 break; 1901 default: 1902 if (channel != D_INTR_CMD) 1903 printk(KERN_WARNING 1904 "DBRI: Ignored Interrupt: %d (0x%x)\n", code, x); 1905 } 1906 } 1907 1908 /* dbri_process_interrupt_buffer advances through the DBRI's interrupt 1909 * buffer until it finds a zero word (indicating nothing more to do 1910 * right now). Non-zero words require processing and are handed off 1911 * to dbri_process_one_interrupt AFTER advancing the pointer. 1912 */ 1913 static void dbri_process_interrupt_buffer(struct snd_dbri *dbri) 1914 { 1915 s32 x; 1916 1917 while ((x = dbri->dma->intr[dbri->dbri_irqp]) != 0) { 1918 dbri->dma->intr[dbri->dbri_irqp] = 0; 1919 dbri->dbri_irqp++; 1920 if (dbri->dbri_irqp == DBRI_INT_BLK) 1921 dbri->dbri_irqp = 1; 1922 1923 dbri_process_one_interrupt(dbri, x); 1924 } 1925 } 1926 1927 static irqreturn_t snd_dbri_interrupt(int irq, void *dev_id) 1928 { 1929 struct snd_dbri *dbri = dev_id; 1930 static int errcnt = 0; 1931 int x; 1932 1933 if (dbri == NULL) 1934 return IRQ_NONE; 1935 spin_lock(&dbri->lock); 1936 1937 /* 1938 * Read it, so the interrupt goes away. 1939 */ 1940 x = sbus_readl(dbri->regs + REG1); 1941 1942 if (x & (D_MRR | D_MLE | D_LBG | D_MBE)) { 1943 u32 tmp; 1944 1945 if (x & D_MRR) 1946 printk(KERN_ERR 1947 "DBRI: Multiple Error Ack on SBus reg1=0x%x\n", 1948 x); 1949 if (x & D_MLE) 1950 printk(KERN_ERR 1951 "DBRI: Multiple Late Error on SBus reg1=0x%x\n", 1952 x); 1953 if (x & D_LBG) 1954 printk(KERN_ERR 1955 "DBRI: Lost Bus Grant on SBus reg1=0x%x\n", x); 1956 if (x & D_MBE) 1957 printk(KERN_ERR 1958 "DBRI: Burst Error on SBus reg1=0x%x\n", x); 1959 1960 /* Some of these SBus errors cause the chip's SBus circuitry 1961 * to be disabled, so just re-enable and try to keep going. 1962 * 1963 * The only one I've seen is MRR, which will be triggered 1964 * if you let a transmit pipe underrun, then try to CDP it. 1965 * 1966 * If these things persist, we reset the chip. 1967 */ 1968 if ((++errcnt) % 10 == 0) { 1969 dprintk(D_INT, "Interrupt errors exceeded.\n"); 1970 dbri_reset(dbri); 1971 } else { 1972 tmp = sbus_readl(dbri->regs + REG0); 1973 tmp &= ~(D_D); 1974 sbus_writel(tmp, dbri->regs + REG0); 1975 } 1976 } 1977 1978 dbri_process_interrupt_buffer(dbri); 1979 1980 spin_unlock(&dbri->lock); 1981 1982 return IRQ_HANDLED; 1983 } 1984 1985 /**************************************************************************** 1986 PCM Interface 1987 ****************************************************************************/ 1988 static const struct snd_pcm_hardware snd_dbri_pcm_hw = { 1989 .info = SNDRV_PCM_INFO_MMAP | 1990 SNDRV_PCM_INFO_INTERLEAVED | 1991 SNDRV_PCM_INFO_BLOCK_TRANSFER | 1992 SNDRV_PCM_INFO_MMAP_VALID | 1993 SNDRV_PCM_INFO_BATCH, 1994 .formats = SNDRV_PCM_FMTBIT_MU_LAW | 1995 SNDRV_PCM_FMTBIT_A_LAW | 1996 SNDRV_PCM_FMTBIT_U8 | 1997 SNDRV_PCM_FMTBIT_S16_BE, 1998 .rates = SNDRV_PCM_RATE_8000_48000 | SNDRV_PCM_RATE_5512, 1999 .rate_min = 5512, 2000 .rate_max = 48000, 2001 .channels_min = 1, 2002 .channels_max = 2, 2003 .buffer_bytes_max = 64 * 1024, 2004 .period_bytes_min = 1, 2005 .period_bytes_max = DBRI_TD_MAXCNT, 2006 .periods_min = 1, 2007 .periods_max = 1024, 2008 }; 2009 2010 static int snd_hw_rule_format(struct snd_pcm_hw_params *params, 2011 struct snd_pcm_hw_rule *rule) 2012 { 2013 struct snd_interval *c = hw_param_interval(params, 2014 SNDRV_PCM_HW_PARAM_CHANNELS); 2015 struct snd_mask *f = hw_param_mask(params, SNDRV_PCM_HW_PARAM_FORMAT); 2016 struct snd_mask fmt; 2017 2018 snd_mask_any(&fmt); 2019 if (c->min > 1) { 2020 fmt.bits[0] &= SNDRV_PCM_FMTBIT_S16_BE; 2021 return snd_mask_refine(f, &fmt); 2022 } 2023 return 0; 2024 } 2025 2026 static int snd_hw_rule_channels(struct snd_pcm_hw_params *params, 2027 struct snd_pcm_hw_rule *rule) 2028 { 2029 struct snd_interval *c = hw_param_interval(params, 2030 SNDRV_PCM_HW_PARAM_CHANNELS); 2031 struct snd_mask *f = hw_param_mask(params, SNDRV_PCM_HW_PARAM_FORMAT); 2032 struct snd_interval ch; 2033 2034 snd_interval_any(&ch); 2035 if (!(f->bits[0] & SNDRV_PCM_FMTBIT_S16_BE)) { 2036 ch.min = 1; 2037 ch.max = 1; 2038 ch.integer = 1; 2039 return snd_interval_refine(c, &ch); 2040 } 2041 return 0; 2042 } 2043 2044 static int snd_dbri_open(struct snd_pcm_substream *substream) 2045 { 2046 struct snd_dbri *dbri = snd_pcm_substream_chip(substream); 2047 struct snd_pcm_runtime *runtime = substream->runtime; 2048 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream); 2049 unsigned long flags; 2050 2051 dprintk(D_USR, "open audio output.\n"); 2052 runtime->hw = snd_dbri_pcm_hw; 2053 2054 spin_lock_irqsave(&dbri->lock, flags); 2055 info->substream = substream; 2056 info->offset = 0; 2057 info->dvma_buffer = 0; 2058 info->pipe = -1; 2059 spin_unlock_irqrestore(&dbri->lock, flags); 2060 2061 snd_pcm_hw_rule_add(runtime, 0, SNDRV_PCM_HW_PARAM_CHANNELS, 2062 snd_hw_rule_format, NULL, SNDRV_PCM_HW_PARAM_FORMAT, 2063 -1); 2064 snd_pcm_hw_rule_add(runtime, 0, SNDRV_PCM_HW_PARAM_FORMAT, 2065 snd_hw_rule_channels, NULL, 2066 SNDRV_PCM_HW_PARAM_CHANNELS, 2067 -1); 2068 2069 cs4215_open(dbri); 2070 2071 return 0; 2072 } 2073 2074 static int snd_dbri_close(struct snd_pcm_substream *substream) 2075 { 2076 struct snd_dbri *dbri = snd_pcm_substream_chip(substream); 2077 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream); 2078 2079 dprintk(D_USR, "close audio output.\n"); 2080 info->substream = NULL; 2081 info->offset = 0; 2082 2083 return 0; 2084 } 2085 2086 static int snd_dbri_hw_params(struct snd_pcm_substream *substream, 2087 struct snd_pcm_hw_params *hw_params) 2088 { 2089 struct snd_pcm_runtime *runtime = substream->runtime; 2090 struct snd_dbri *dbri = snd_pcm_substream_chip(substream); 2091 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream); 2092 int direction; 2093 int ret; 2094 2095 /* set sampling rate, audio format and number of channels */ 2096 ret = cs4215_prepare(dbri, params_rate(hw_params), 2097 params_format(hw_params), 2098 params_channels(hw_params)); 2099 if (ret != 0) 2100 return ret; 2101 2102 if ((ret = snd_pcm_lib_malloc_pages(substream, 2103 params_buffer_bytes(hw_params))) < 0) { 2104 printk(KERN_ERR "malloc_pages failed with %d\n", ret); 2105 return ret; 2106 } 2107 2108 /* hw_params can get called multiple times. Only map the DMA once. 2109 */ 2110 if (info->dvma_buffer == 0) { 2111 if (DBRI_STREAMNO(substream) == DBRI_PLAY) 2112 direction = DMA_TO_DEVICE; 2113 else 2114 direction = DMA_FROM_DEVICE; 2115 2116 info->dvma_buffer = 2117 dma_map_single(&dbri->op->dev, 2118 runtime->dma_area, 2119 params_buffer_bytes(hw_params), 2120 direction); 2121 } 2122 2123 direction = params_buffer_bytes(hw_params); 2124 dprintk(D_USR, "hw_params: %d bytes, dvma=%x\n", 2125 direction, info->dvma_buffer); 2126 return 0; 2127 } 2128 2129 static int snd_dbri_hw_free(struct snd_pcm_substream *substream) 2130 { 2131 struct snd_dbri *dbri = snd_pcm_substream_chip(substream); 2132 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream); 2133 int direction; 2134 2135 dprintk(D_USR, "hw_free.\n"); 2136 2137 /* hw_free can get called multiple times. Only unmap the DMA once. 2138 */ 2139 if (info->dvma_buffer) { 2140 if (DBRI_STREAMNO(substream) == DBRI_PLAY) 2141 direction = DMA_TO_DEVICE; 2142 else 2143 direction = DMA_FROM_DEVICE; 2144 2145 dma_unmap_single(&dbri->op->dev, info->dvma_buffer, 2146 substream->runtime->buffer_size, direction); 2147 info->dvma_buffer = 0; 2148 } 2149 if (info->pipe != -1) { 2150 reset_pipe(dbri, info->pipe); 2151 info->pipe = -1; 2152 } 2153 2154 return snd_pcm_lib_free_pages(substream); 2155 } 2156 2157 static int snd_dbri_prepare(struct snd_pcm_substream *substream) 2158 { 2159 struct snd_dbri *dbri = snd_pcm_substream_chip(substream); 2160 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream); 2161 int ret; 2162 2163 info->size = snd_pcm_lib_buffer_bytes(substream); 2164 if (DBRI_STREAMNO(substream) == DBRI_PLAY) 2165 info->pipe = 4; /* Send pipe */ 2166 else 2167 info->pipe = 6; /* Receive pipe */ 2168 2169 spin_lock_irq(&dbri->lock); 2170 info->offset = 0; 2171 2172 /* Setup the all the transmit/receive descriptors to cover the 2173 * whole DMA buffer. 2174 */ 2175 ret = setup_descs(dbri, DBRI_STREAMNO(substream), 2176 snd_pcm_lib_period_bytes(substream)); 2177 2178 spin_unlock_irq(&dbri->lock); 2179 2180 dprintk(D_USR, "prepare audio output. %d bytes\n", info->size); 2181 return ret; 2182 } 2183 2184 static int snd_dbri_trigger(struct snd_pcm_substream *substream, int cmd) 2185 { 2186 struct snd_dbri *dbri = snd_pcm_substream_chip(substream); 2187 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream); 2188 int ret = 0; 2189 2190 switch (cmd) { 2191 case SNDRV_PCM_TRIGGER_START: 2192 dprintk(D_USR, "start audio, period is %d bytes\n", 2193 (int)snd_pcm_lib_period_bytes(substream)); 2194 /* Re-submit the TDs. */ 2195 xmit_descs(dbri); 2196 break; 2197 case SNDRV_PCM_TRIGGER_STOP: 2198 dprintk(D_USR, "stop audio.\n"); 2199 reset_pipe(dbri, info->pipe); 2200 break; 2201 default: 2202 ret = -EINVAL; 2203 } 2204 2205 return ret; 2206 } 2207 2208 static snd_pcm_uframes_t snd_dbri_pointer(struct snd_pcm_substream *substream) 2209 { 2210 struct snd_dbri *dbri = snd_pcm_substream_chip(substream); 2211 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream); 2212 snd_pcm_uframes_t ret; 2213 2214 ret = bytes_to_frames(substream->runtime, info->offset) 2215 % substream->runtime->buffer_size; 2216 dprintk(D_USR, "I/O pointer: %ld frames of %ld.\n", 2217 ret, substream->runtime->buffer_size); 2218 return ret; 2219 } 2220 2221 static const struct snd_pcm_ops snd_dbri_ops = { 2222 .open = snd_dbri_open, 2223 .close = snd_dbri_close, 2224 .ioctl = snd_pcm_lib_ioctl, 2225 .hw_params = snd_dbri_hw_params, 2226 .hw_free = snd_dbri_hw_free, 2227 .prepare = snd_dbri_prepare, 2228 .trigger = snd_dbri_trigger, 2229 .pointer = snd_dbri_pointer, 2230 }; 2231 2232 static int snd_dbri_pcm(struct snd_card *card) 2233 { 2234 struct snd_pcm *pcm; 2235 int err; 2236 2237 if ((err = snd_pcm_new(card, 2238 /* ID */ "sun_dbri", 2239 /* device */ 0, 2240 /* playback count */ 1, 2241 /* capture count */ 1, &pcm)) < 0) 2242 return err; 2243 2244 snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_PLAYBACK, &snd_dbri_ops); 2245 snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_CAPTURE, &snd_dbri_ops); 2246 2247 pcm->private_data = card->private_data; 2248 pcm->info_flags = 0; 2249 strcpy(pcm->name, card->shortname); 2250 2251 snd_pcm_lib_preallocate_pages_for_all(pcm, SNDRV_DMA_TYPE_CONTINUOUS, 2252 snd_dma_continuous_data(GFP_KERNEL), 2253 64 * 1024, 64 * 1024); 2254 return 0; 2255 } 2256 2257 /***************************************************************************** 2258 Mixer interface 2259 *****************************************************************************/ 2260 2261 static int snd_cs4215_info_volume(struct snd_kcontrol *kcontrol, 2262 struct snd_ctl_elem_info *uinfo) 2263 { 2264 uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; 2265 uinfo->count = 2; 2266 uinfo->value.integer.min = 0; 2267 if (kcontrol->private_value == DBRI_PLAY) 2268 uinfo->value.integer.max = DBRI_MAX_VOLUME; 2269 else 2270 uinfo->value.integer.max = DBRI_MAX_GAIN; 2271 return 0; 2272 } 2273 2274 static int snd_cs4215_get_volume(struct snd_kcontrol *kcontrol, 2275 struct snd_ctl_elem_value *ucontrol) 2276 { 2277 struct snd_dbri *dbri = snd_kcontrol_chip(kcontrol); 2278 struct dbri_streaminfo *info; 2279 2280 if (snd_BUG_ON(!dbri)) 2281 return -EINVAL; 2282 info = &dbri->stream_info[kcontrol->private_value]; 2283 2284 ucontrol->value.integer.value[0] = info->left_gain; 2285 ucontrol->value.integer.value[1] = info->right_gain; 2286 return 0; 2287 } 2288 2289 static int snd_cs4215_put_volume(struct snd_kcontrol *kcontrol, 2290 struct snd_ctl_elem_value *ucontrol) 2291 { 2292 struct snd_dbri *dbri = snd_kcontrol_chip(kcontrol); 2293 struct dbri_streaminfo *info = 2294 &dbri->stream_info[kcontrol->private_value]; 2295 unsigned int vol[2]; 2296 int changed = 0; 2297 2298 vol[0] = ucontrol->value.integer.value[0]; 2299 vol[1] = ucontrol->value.integer.value[1]; 2300 if (kcontrol->private_value == DBRI_PLAY) { 2301 if (vol[0] > DBRI_MAX_VOLUME || vol[1] > DBRI_MAX_VOLUME) 2302 return -EINVAL; 2303 } else { 2304 if (vol[0] > DBRI_MAX_GAIN || vol[1] > DBRI_MAX_GAIN) 2305 return -EINVAL; 2306 } 2307 2308 if (info->left_gain != vol[0]) { 2309 info->left_gain = vol[0]; 2310 changed = 1; 2311 } 2312 if (info->right_gain != vol[1]) { 2313 info->right_gain = vol[1]; 2314 changed = 1; 2315 } 2316 if (changed) { 2317 /* First mute outputs, and wait 1/8000 sec (125 us) 2318 * to make sure this takes. This avoids clicking noises. 2319 */ 2320 cs4215_setdata(dbri, 1); 2321 udelay(125); 2322 cs4215_setdata(dbri, 0); 2323 } 2324 return changed; 2325 } 2326 2327 static int snd_cs4215_info_single(struct snd_kcontrol *kcontrol, 2328 struct snd_ctl_elem_info *uinfo) 2329 { 2330 int mask = (kcontrol->private_value >> 16) & 0xff; 2331 2332 uinfo->type = (mask == 1) ? 2333 SNDRV_CTL_ELEM_TYPE_BOOLEAN : SNDRV_CTL_ELEM_TYPE_INTEGER; 2334 uinfo->count = 1; 2335 uinfo->value.integer.min = 0; 2336 uinfo->value.integer.max = mask; 2337 return 0; 2338 } 2339 2340 static int snd_cs4215_get_single(struct snd_kcontrol *kcontrol, 2341 struct snd_ctl_elem_value *ucontrol) 2342 { 2343 struct snd_dbri *dbri = snd_kcontrol_chip(kcontrol); 2344 int elem = kcontrol->private_value & 0xff; 2345 int shift = (kcontrol->private_value >> 8) & 0xff; 2346 int mask = (kcontrol->private_value >> 16) & 0xff; 2347 int invert = (kcontrol->private_value >> 24) & 1; 2348 2349 if (snd_BUG_ON(!dbri)) 2350 return -EINVAL; 2351 2352 if (elem < 4) 2353 ucontrol->value.integer.value[0] = 2354 (dbri->mm.data[elem] >> shift) & mask; 2355 else 2356 ucontrol->value.integer.value[0] = 2357 (dbri->mm.ctrl[elem - 4] >> shift) & mask; 2358 2359 if (invert == 1) 2360 ucontrol->value.integer.value[0] = 2361 mask - ucontrol->value.integer.value[0]; 2362 return 0; 2363 } 2364 2365 static int snd_cs4215_put_single(struct snd_kcontrol *kcontrol, 2366 struct snd_ctl_elem_value *ucontrol) 2367 { 2368 struct snd_dbri *dbri = snd_kcontrol_chip(kcontrol); 2369 int elem = kcontrol->private_value & 0xff; 2370 int shift = (kcontrol->private_value >> 8) & 0xff; 2371 int mask = (kcontrol->private_value >> 16) & 0xff; 2372 int invert = (kcontrol->private_value >> 24) & 1; 2373 int changed = 0; 2374 unsigned short val; 2375 2376 if (snd_BUG_ON(!dbri)) 2377 return -EINVAL; 2378 2379 val = (ucontrol->value.integer.value[0] & mask); 2380 if (invert == 1) 2381 val = mask - val; 2382 val <<= shift; 2383 2384 if (elem < 4) { 2385 dbri->mm.data[elem] = (dbri->mm.data[elem] & 2386 ~(mask << shift)) | val; 2387 changed = (val != dbri->mm.data[elem]); 2388 } else { 2389 dbri->mm.ctrl[elem - 4] = (dbri->mm.ctrl[elem - 4] & 2390 ~(mask << shift)) | val; 2391 changed = (val != dbri->mm.ctrl[elem - 4]); 2392 } 2393 2394 dprintk(D_GEN, "put_single: mask=0x%x, changed=%d, " 2395 "mixer-value=%ld, mm-value=0x%x\n", 2396 mask, changed, ucontrol->value.integer.value[0], 2397 dbri->mm.data[elem & 3]); 2398 2399 if (changed) { 2400 /* First mute outputs, and wait 1/8000 sec (125 us) 2401 * to make sure this takes. This avoids clicking noises. 2402 */ 2403 cs4215_setdata(dbri, 1); 2404 udelay(125); 2405 cs4215_setdata(dbri, 0); 2406 } 2407 return changed; 2408 } 2409 2410 /* Entries 0-3 map to the 4 data timeslots, entries 4-7 map to the 4 control 2411 timeslots. Shift is the bit offset in the timeslot, mask defines the 2412 number of bits. invert is a boolean for use with attenuation. 2413 */ 2414 #define CS4215_SINGLE(xname, entry, shift, mask, invert) \ 2415 { .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = (xname), \ 2416 .info = snd_cs4215_info_single, \ 2417 .get = snd_cs4215_get_single, .put = snd_cs4215_put_single, \ 2418 .private_value = (entry) | ((shift) << 8) | ((mask) << 16) | \ 2419 ((invert) << 24) }, 2420 2421 static struct snd_kcontrol_new dbri_controls[] = { 2422 { 2423 .iface = SNDRV_CTL_ELEM_IFACE_MIXER, 2424 .name = "Playback Volume", 2425 .info = snd_cs4215_info_volume, 2426 .get = snd_cs4215_get_volume, 2427 .put = snd_cs4215_put_volume, 2428 .private_value = DBRI_PLAY, 2429 }, 2430 CS4215_SINGLE("Headphone switch", 0, 7, 1, 0) 2431 CS4215_SINGLE("Line out switch", 0, 6, 1, 0) 2432 CS4215_SINGLE("Speaker switch", 1, 6, 1, 0) 2433 { 2434 .iface = SNDRV_CTL_ELEM_IFACE_MIXER, 2435 .name = "Capture Volume", 2436 .info = snd_cs4215_info_volume, 2437 .get = snd_cs4215_get_volume, 2438 .put = snd_cs4215_put_volume, 2439 .private_value = DBRI_REC, 2440 }, 2441 /* FIXME: mic/line switch */ 2442 CS4215_SINGLE("Line in switch", 2, 4, 1, 0) 2443 CS4215_SINGLE("High Pass Filter switch", 5, 7, 1, 0) 2444 CS4215_SINGLE("Monitor Volume", 3, 4, 0xf, 1) 2445 CS4215_SINGLE("Mic boost", 4, 4, 1, 1) 2446 }; 2447 2448 static int snd_dbri_mixer(struct snd_card *card) 2449 { 2450 int idx, err; 2451 struct snd_dbri *dbri; 2452 2453 if (snd_BUG_ON(!card || !card->private_data)) 2454 return -EINVAL; 2455 dbri = card->private_data; 2456 2457 strcpy(card->mixername, card->shortname); 2458 2459 for (idx = 0; idx < ARRAY_SIZE(dbri_controls); idx++) { 2460 err = snd_ctl_add(card, 2461 snd_ctl_new1(&dbri_controls[idx], dbri)); 2462 if (err < 0) 2463 return err; 2464 } 2465 2466 for (idx = DBRI_REC; idx < DBRI_NO_STREAMS; idx++) { 2467 dbri->stream_info[idx].left_gain = 0; 2468 dbri->stream_info[idx].right_gain = 0; 2469 } 2470 2471 return 0; 2472 } 2473 2474 /**************************************************************************** 2475 /proc interface 2476 ****************************************************************************/ 2477 static void dbri_regs_read(struct snd_info_entry *entry, 2478 struct snd_info_buffer *buffer) 2479 { 2480 struct snd_dbri *dbri = entry->private_data; 2481 2482 snd_iprintf(buffer, "REG0: 0x%x\n", sbus_readl(dbri->regs + REG0)); 2483 snd_iprintf(buffer, "REG2: 0x%x\n", sbus_readl(dbri->regs + REG2)); 2484 snd_iprintf(buffer, "REG8: 0x%x\n", sbus_readl(dbri->regs + REG8)); 2485 snd_iprintf(buffer, "REG9: 0x%x\n", sbus_readl(dbri->regs + REG9)); 2486 } 2487 2488 #ifdef DBRI_DEBUG 2489 static void dbri_debug_read(struct snd_info_entry *entry, 2490 struct snd_info_buffer *buffer) 2491 { 2492 struct snd_dbri *dbri = entry->private_data; 2493 int pipe; 2494 snd_iprintf(buffer, "debug=%d\n", dbri_debug); 2495 2496 for (pipe = 0; pipe < 32; pipe++) { 2497 if (pipe_active(dbri, pipe)) { 2498 struct dbri_pipe *pptr = &dbri->pipes[pipe]; 2499 snd_iprintf(buffer, 2500 "Pipe %d: %s SDP=0x%x desc=%d, " 2501 "len=%d next %d\n", 2502 pipe, 2503 (pptr->sdp & D_SDP_TO_SER) ? "output" : 2504 "input", 2505 pptr->sdp, pptr->desc, 2506 pptr->length, pptr->nextpipe); 2507 } 2508 } 2509 } 2510 #endif 2511 2512 static void snd_dbri_proc(struct snd_card *card) 2513 { 2514 struct snd_dbri *dbri = card->private_data; 2515 2516 snd_card_ro_proc_new(card, "regs", dbri, dbri_regs_read); 2517 #ifdef DBRI_DEBUG 2518 snd_card_ro_proc_new(card, "debug", dbri, dbri_debug_read); 2519 #endif 2520 } 2521 2522 /* 2523 **************************************************************************** 2524 **************************** Initialization ******************************** 2525 **************************************************************************** 2526 */ 2527 static void snd_dbri_free(struct snd_dbri *dbri); 2528 2529 static int snd_dbri_create(struct snd_card *card, 2530 struct platform_device *op, 2531 int irq, int dev) 2532 { 2533 struct snd_dbri *dbri = card->private_data; 2534 int err; 2535 2536 spin_lock_init(&dbri->lock); 2537 dbri->op = op; 2538 dbri->irq = irq; 2539 2540 dbri->dma = dma_alloc_coherent(&op->dev, sizeof(struct dbri_dma), 2541 &dbri->dma_dvma, GFP_KERNEL); 2542 if (!dbri->dma) 2543 return -ENOMEM; 2544 2545 dprintk(D_GEN, "DMA Cmd Block 0x%p (%pad)\n", 2546 dbri->dma, dbri->dma_dvma); 2547 2548 /* Map the registers into memory. */ 2549 dbri->regs_size = resource_size(&op->resource[0]); 2550 dbri->regs = of_ioremap(&op->resource[0], 0, 2551 dbri->regs_size, "DBRI Registers"); 2552 if (!dbri->regs) { 2553 printk(KERN_ERR "DBRI: could not allocate registers\n"); 2554 dma_free_coherent(&op->dev, sizeof(struct dbri_dma), 2555 (void *)dbri->dma, dbri->dma_dvma); 2556 return -EIO; 2557 } 2558 2559 err = request_irq(dbri->irq, snd_dbri_interrupt, IRQF_SHARED, 2560 "DBRI audio", dbri); 2561 if (err) { 2562 printk(KERN_ERR "DBRI: Can't get irq %d\n", dbri->irq); 2563 of_iounmap(&op->resource[0], dbri->regs, dbri->regs_size); 2564 dma_free_coherent(&op->dev, sizeof(struct dbri_dma), 2565 (void *)dbri->dma, dbri->dma_dvma); 2566 return err; 2567 } 2568 2569 /* Do low level initialization of the DBRI and CS4215 chips */ 2570 dbri_initialize(dbri); 2571 err = cs4215_init(dbri); 2572 if (err) { 2573 snd_dbri_free(dbri); 2574 return err; 2575 } 2576 2577 return 0; 2578 } 2579 2580 static void snd_dbri_free(struct snd_dbri *dbri) 2581 { 2582 dprintk(D_GEN, "snd_dbri_free\n"); 2583 dbri_reset(dbri); 2584 2585 if (dbri->irq) 2586 free_irq(dbri->irq, dbri); 2587 2588 if (dbri->regs) 2589 of_iounmap(&dbri->op->resource[0], dbri->regs, dbri->regs_size); 2590 2591 if (dbri->dma) 2592 dma_free_coherent(&dbri->op->dev, 2593 sizeof(struct dbri_dma), 2594 (void *)dbri->dma, dbri->dma_dvma); 2595 } 2596 2597 static int dbri_probe(struct platform_device *op) 2598 { 2599 struct snd_dbri *dbri; 2600 struct resource *rp; 2601 struct snd_card *card; 2602 static int dev = 0; 2603 int irq; 2604 int err; 2605 2606 if (dev >= SNDRV_CARDS) 2607 return -ENODEV; 2608 if (!enable[dev]) { 2609 dev++; 2610 return -ENOENT; 2611 } 2612 2613 irq = op->archdata.irqs[0]; 2614 if (irq <= 0) { 2615 printk(KERN_ERR "DBRI-%d: No IRQ.\n", dev); 2616 return -ENODEV; 2617 } 2618 2619 err = snd_card_new(&op->dev, index[dev], id[dev], THIS_MODULE, 2620 sizeof(struct snd_dbri), &card); 2621 if (err < 0) 2622 return err; 2623 2624 strcpy(card->driver, "DBRI"); 2625 strcpy(card->shortname, "Sun DBRI"); 2626 rp = &op->resource[0]; 2627 sprintf(card->longname, "%s at 0x%02lx:0x%016Lx, irq %d", 2628 card->shortname, 2629 rp->flags & 0xffL, (unsigned long long)rp->start, irq); 2630 2631 err = snd_dbri_create(card, op, irq, dev); 2632 if (err < 0) { 2633 snd_card_free(card); 2634 return err; 2635 } 2636 2637 dbri = card->private_data; 2638 err = snd_dbri_pcm(card); 2639 if (err < 0) 2640 goto _err; 2641 2642 err = snd_dbri_mixer(card); 2643 if (err < 0) 2644 goto _err; 2645 2646 /* /proc file handling */ 2647 snd_dbri_proc(card); 2648 dev_set_drvdata(&op->dev, card); 2649 2650 err = snd_card_register(card); 2651 if (err < 0) 2652 goto _err; 2653 2654 printk(KERN_INFO "audio%d at %p (irq %d) is DBRI(%c)+CS4215(%d)\n", 2655 dev, dbri->regs, 2656 dbri->irq, op->dev.of_node->name[9], dbri->mm.version); 2657 dev++; 2658 2659 return 0; 2660 2661 _err: 2662 snd_dbri_free(dbri); 2663 snd_card_free(card); 2664 return err; 2665 } 2666 2667 static int dbri_remove(struct platform_device *op) 2668 { 2669 struct snd_card *card = dev_get_drvdata(&op->dev); 2670 2671 snd_dbri_free(card->private_data); 2672 snd_card_free(card); 2673 2674 return 0; 2675 } 2676 2677 static const struct of_device_id dbri_match[] = { 2678 { 2679 .name = "SUNW,DBRIe", 2680 }, 2681 { 2682 .name = "SUNW,DBRIf", 2683 }, 2684 {}, 2685 }; 2686 2687 MODULE_DEVICE_TABLE(of, dbri_match); 2688 2689 static struct platform_driver dbri_sbus_driver = { 2690 .driver = { 2691 .name = "dbri", 2692 .of_match_table = dbri_match, 2693 }, 2694 .probe = dbri_probe, 2695 .remove = dbri_remove, 2696 }; 2697 2698 module_platform_driver(dbri_sbus_driver); 2699